Search Documents

By K. Vanbroekhoven

An industrial site near the centre of a historical town in Flanders is characterized by chromium(VI) contamination of the groundwater. Since the potential for natural attenuation was not sufficient to control the groundwater plume as observed from different analyses like pH, Eh, soil oxidation and reduction capacity, the feasibility of site remediation based on in-situ bioprecipitation of chromium was examined in lab microcosm studies. By creating reducing conditions by addition of a carbon source in the groundwater, chromium(VI) can be biologically reduced to chromium(III), which can form an insoluble precipitate of chromium(III) hydroxide. Microcosms contained contaminated groundwater and aquifer samples that were collected and manipulated under anaerobic conditions. Three different carbon sources were screened for their effectiveness: molasses from sugar beet production, molasses form starch production (protamylasses) based on potato juice and lactate. The different concentrations of sugar molasses were used to determine the optimal conditions. A range of parameters was monitored at regular time intervals for a period of six months such as chromium(VI) and chromium(III), DOC, methane, pH, Eh. A rapid conversion of chromium(VI) to chromium(III) was observed for all conditions tested. However, extensive removal of chromium from the groundwater by precipitation was only achieved for a limited number of conditions. In general, lactate was found to be the most effective carbon source, slightly better than the lowest concentration of sugar molasses that was tested, which itself was more effective than molasses based on potato. Higher concentrations of molasses, although causing a steeper decline in redox potential, resulted in less effective Cr removal. Typically, the fermentation of molasses results in acidification and this drop in pH may hinder the formation of insoluble chromium(III)hydroxides. It may also be possible that certain components of the molasses form soluble complexes with chromium(III). For lactate, no significant drop in pH was observed. Following the laboratory microcosm tests, the stability of the chromium precipitates was examined by performing a sequential extraction on the microcosm materials. These were performed under redox conditions which were similar to the ones observed in the field. Since the outcome of these tests was positive, a pilot scale test was implemented in the field in April 2005. Two different substrates, the cheap waste product sugar molasses and lactate are being injected creating two different impact zones and typical parameters are monitored. Frequent re-injections were important to maintain reduced conditions and are carried out three-weekly up to now. To study the stability of precipitates formed, mesocosm socks containing aquifer material were installed in the monitoring wells and harvested at regular intervals. Results of this pilot test will be presented and compared to the laboratory results. Based on the success of this field test, a full scale process will be designed and implemented as remediation strategy.

Jan 1, 2006

By Eric Hansen, Todd Wanless, Chris Mueller, Shannon Dunne, Scott Elmer

Between 2010 and 2018, Houston added more than 1 Million residents; the third largest rate of growth in the nation. With growth, the region faces new challenges with water supply, capacity of its wastewater system, and regional drainage. While tunnel construction has been limited in Houston since the Clean Water Program of 1990s, it is about to see a resurgence to improve water supply reliability and to reduce flood risks and sanitary sewer overflows. This paper examines the challenges with “going deep” below the built urban environment and related to high ground water; stiff, fissured clays; flowing silts and sands; faults; hazardous materials; and abandoned well fields.

Jun 13, 2021

By H. F. Anderson

The Palabora Mining Company Ltd. is probably best known for its production of copper since 1965. The success of the PMC mine lies in the outstanding technical and highly organized efficiencies applied to the massive mining, transportation, and treatment operations necessary to produce profitable copper. We are not however going to discuss the well-known copper operation but the extremely successful recovery and marketing of Baddeleyite by the PMC group. Let us first review the extraction process at the Heavy Minerals Plant. Non-magnetic ground ore from the copper magnetic separators is processed in the Heavy Minerals Plant for the extraction of the "heavy minerals" uranium and zirconia (Baddeleyite). Thorium is also present as a potentially recoverable mineral. The content of the minerals in the feed is probably the lowest in the world to be treated commercially. Minerals are separated from the waste ore by a gravity separation process in which the high density minerals segregate preferentially in a waterborne system.

Jan 1, 1985

By G. E. Wasson

Coal in most refuse ponds including those owned by Consolidation Coal Company can be recovered by froth flotation techniques. Laboratory studies show that the flotation conditions required for coal recovery varied greatly from pond to pond. The variables found to be most important for high coal recovery and low product ash were: a) the amount and type of flotation reagents and b) the degree of conditioning before flotation. Coal recovery at a rate of 0.504 kg/s (2 tons/hr) was demonstrated at a pond site employing a mobile froth flotation unit.

Jan 1, 1988

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

By S. Ford

The introduction of recent advances in molecular biology into the field of microbial ecology has made available a powerful set of analytical tools for dissecting the structure of microbial communities in natural environments. The use of these approaches, many of them based on DNA-DNA hybridization enables the researcher to assess the occurrence of specific DNA sequences among the natural bacterial flora (Ford and Olson 1987). These techniques promise to have wide application as tools for monitoring the spread of introduced microorganisms (Trevors, 198'): Ford and Olson. 1987) and have been used to examine the response of bacterial communities to environmental contaminants and stressors (Barkay and Olson. 1986. Olson and Ford. 1986. Olson. Ford and Lester 1987) The occurrence of heavy metal resistance among microorganisms has been discussed as a possible tool for the detection of pathfinder elements employed in mineral exploration (Olson and Barkay 1986). In addition, the occurrence of heavy metal resistant bacteria may be utilized in protocols for assessing the occurrence and biological impact of contamination occurring as a consequence of mining operations. In this context the use of DNA hybridization technology enables the investigator to directly quantify the number of heavy metal resistant bacteria by the use of genetic probes specific for those resistance genes. The implementation of a strategy for detection of heavy metal resistance genes by hybridization technology is dependent on the availability of data on the genetic systems which encode resistance The availability of extensive DNA sequence data on mercury resistance genes (Brown et a11986. Barrineau et al 1984) has lead us to use gene probes specific for mercury resistance within natural bacterial populations as a model system for investigating the response of these bacterial populations to the occurrence of mercury In the environment.

Jan 1, 1988

By W. A. Weimer

Coal and coal mining is no longer the mighty king of industry and in our daily lives and homes that it once had the privilege of commanding. Many of you will remember that one of the chores of your youth was to bring in the scuttles of coal, morning and night, to feed the heater or stoke the furnace in the morning and bank it at bedtime. Growth of gas and oil have displaced coal in home furnaces and commercial buildings, and have taken over some segments of industrial markets. The coal burning locomotives have virtually disappeared in favor of the more efficient diesel engine. However, coal as a prime mover still holds its strategic position as is evidenced by act that the electric power industry almost entirely depends upon coal for its generation.

Jan 1, 1961

By O. Ofor

Finely-ground hematitic ore, too high in silica (quartz) to be commercially viable, was treated by emulsion flotation. A three-component emulsion mixture was used at temperatures ranging from ambient (22° C) to 30° C, 40° C, 49 °C, 59° C and 68° C. The optimal emulsion dosage and composition at ambient temperature were used to determine that dosage for higher-temperature flotation tests. The crushed ore (100%, -8 mesh) was repeatedly washed with tap water, and the filtrate's ionic content was analyzed. The separation efficiency values (a measure of the selective separation and concentration of hematite from gangue minerals) demonstrated temperature dependence, with marked increases at temperatures above ambient. The optimal separation efficiency occurred within the range from 30° C to 60° C. The improved separation efficiencies at temperatures exceeding ambient are explained by quartz depression. This depression is attributed to: • the precipitation of quartz-activating cations, principally calcium and magnesium, at increasing temperature; and • temperature's effect on the collector's solubility and attachment to the aqueous hematite surface.

Jan 1, 1993

By Fritz Kleiner, Walter Meintrup

On Nov. 4, 1981 A/S Sydvaranger's 1-kt/h (1,100-stph) wet-process, iron ore ball mill completed its first four months of uninterrupted, full-load operation in Kirkenes, Norway. This 6.5-m-diam (21-ft-diam) mill is driven by a gearless ring or wraparound 8.1-MW (10,860-hp) motor at 13.1 rpm-a first of a kind in this segment of industry. This article examines reasons for selecting this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes the installation in Norway. History For almost a decade, good operating experiences have been gained with 28 gearless ring motor drives in the cement industry, driving 2.5 to 4-m-diam (8.2 to 13-ft-diam) tube mills with drive powers ranging from about 3-4 MW (4,000 - 8,000 hp). Why then did the mineral ore processing industry hesitate until 1980 to adopt this successful concept for similar applications on ball, semiautogenous, and autogenous mills? There are a number of good reasons in the eyes of conservative mill builders and operators, the most commonly cited ones are: • No operating experience in this segment of specialized industry. • More severe environmental conditions in the wet ore grinding process. • An indifferent attitude of mill builders and electric motor manufacturers towards new drive technologies. • Limited confidence in solid-state power supply systems, such as frequency converters of the required size. There have been and still are numerous problems associated with low-speed geared mill drives of any kind, especially with individual motor/gear sizes approaching or exceeding about 4 MW (5,360 hp). Every mill builder knows about them, but operators learn to accept them as inevitable. The Decision to Change Three things combined to break this technological stalemate: the courage and progressive spirit of one major iron ore processor in Scandinavia, the cooperation of three experienced manufacturers, and an unusual application problem that could not be solved by any conventional approach. The last factor was surely the decisive one, but the first one does not come as a surprise either. The Swedes near Kiruna and the Norwegians around Kirkenes are experienced ore miners and processors, and much credit goes to them for technological breakthroughs in the industry. At A/S Sydvaranger in Kirkenes, above the Polar circle at about the latitude of Alaska's northern tip, the existing grinding facilities, with a total of 14 100 to 240-t/h (110 to 264-stph) ball mills, can not be expanded. Nevertheless, to increase mill throughput, only installing a larger mill in place of an existing smaller one was a practical alternative. For this replacement, the owners set requirements that seemed impossible to meet: • The old 100-t/h (110-stph) ball mill should be replaced with a new ball mill with 10 times the rated throughput, without significantly impairing the operation of the remaining mills, and without significantly changing the mill building. • The new mill should have a variable-speed drive to ultimately optimize the grinding process by means of a closed-loop process¬computer-controlled grinding cycle, and to minimize the specific energy consumption. • Availability, efficiency, and life expectancy of all new components must be higher than those being replaced. • Inrush-current and harmonic loads on the rather weak electric supply line must be minimized to ensure safe plant operation. All old ball mills at A/S Sydvaranger are the geared type, using single synchronous and wound-rotor, slow-speed motors with ring-and-pinion gears. Operators are familiar with the limitations and problems associated with such drives, and they are aware that the following items become major concerns when drive powers are drastically increased: • Gears are subject to wear and tear, require frequent maintenance, and eventual replacement of major parts. • Gears are sensitive to misalignment, overload, and thermal distortion, limiting their useful life. • On dual or quadruple drives, load-sharing and torque oscillations between motors can be a major reason for concern. • At these speeds, ring-and-pinion gears reach their torque transmission capabilities altogether at around 4 MW (5,360 hp) per motor/pinion. To obtain the desired variable-speed performance of the new drive, the only practical and economical conventional solution would have been a frequency-controlled, low- or medium-speed dual motor drive with about 8 MW (10,720 hp) of power. This, however, was not feasible because of limited floor space. Therefore, bids were solicited for the alternative drive method, the gearless ring motor. General Considerations Why are such large mills considered? After all, one could avoid all the problems by simply staying with smaller mill unit sizes. Under competitive pressures of free markets, however, grinding efficiencies and specific energy consumption become key factors in selecting new equipment. Specific energy consumption of ball mills decreases with increas-

Jan 9, 1982

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Roof stability in the belt entry is critical for safe and continuous production of coal during longwall mining. Previous studies of roof falls that occurred in belt entries have shown that the roof falls were largely associated with high in situ and longwall-induced horizontal stresses [1,2,3,4]. To properly support the roof in a belt entry, it is important to understand how longwall-induced horizontal stress changes can affect roof stability in the belt entry. Monitoring of horizontal stress changes was conducted in the belt entries of two Pittsburgh seam longwall panels oriented unfavorably to the major horizontal stress. Numerical models were also set up to investigate how horizontal stress concentrates and relieves in the belt-entry roof near the face as panel orientation changes. Both measurements and modeling results show that high horizontal stress concentrates in the belt entry roof within about 15 m outby the face. The study demonstrates that longwall-induced differential horizontal stress can be used to evaluate the horizontal stress concentration factors. The horizontal stress concentration factors change with panel orientation, resulting in high stress concentrations at orientations between 20 and 110° and low stress concentrations between 130 and 180°. Roof support strategies are given for the belt entries under the influence of high horizontal stress. For unfavorably oriented panels in weak roof conditions, supplementary support should be installed during development, and cable bolts should be anchored into a stable roof horizon. The bolting pattern should be designed to cover both entry corners and the entry center to prevent potential roof cutters and sagging.

Jan 1, 2023

By William G. Pariseau

The flexure of geologic strata, a phenomenon of inter- est to geologists and mining engineers alike, is examined as a sheet bending problem' in Coulomb plasticity. Formulae for the distribution of stress, strain and displacement increments, volume change, change in the length of the central surface and power of dissipation, as well as for the neutral surface shift are given. Strains of any magnitude are considered. The analysis shows that deeply buried strata may bend and develop "tensile" cracks under generally compressive states of stress. It is also shown that bed separation and high capacity props are desirable in mechanized longwall mining, a result in keeping with operating experience. Although speculative at this time, the analysis provides a rational working hypothesis as regards the problem of strata flexure and control.

Jan 1, 1968

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By X. Y. Yu, X. A. Wei, A. Zeng

"The flotation behaviors of diaspore and three kinds of silicate minerals - kaolinite, illite and pyrophyllite - using an organosilicon cationic surfactant as collector were investigated as functions of reagent concentration and pulp pH. The results show that the organosilicon cationic collector QAS122 is a suitable collector for the flotation of aluminosilicate minerals but has weak collecting ability with regard to diaspore, enabling the flotation separation of diaspore from silicate minerals using QAS122 as collector. The flotation of a bauxite ore was then studied in detail. Finally, a reverse flotation separation process was used to process a low-grade bauxite ore. It was concluded that use of the organosilicon cationic collector is effective. A concentrate with aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, of 9.67 was obtained from natural bauxite ore with A/S of 6.07 at pH of around 11. The Al2O3 recovery rate was 81.72 percent. IntroductionChina has abundant bauxite ore resources, but more than 98 percent of the bauxite ores are the diasporic type, with the characteristics of complex mineral composition, low aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, and difficulty of processing. The gangue minerals in bauxite ores are mainly kaolinite, pyrophyllite and illite, containing titanium and iron impurities (Zong et al., 2008). It is known that high-grade bauxite ore, with A/S greater than 8, can be processed directly by the Bayer process (Papanastassiou et al., 2002; Ma et al., 1996). However, Chinese diasporic ores have been processed mainly by the sintering process, which is environmentally damaging and energy intensive. Increasing the A/S of the diasporic ores using a flotation method is needed (Xia et al., 2010).Froth flotation is one of the most widely used processes to concentrate valuable minerals in beneficiation ores. It is particularly useful for separating finely ground ores from their associated gangue minerals. For diasporic bauxite ores, flotation is applied to obtain high-quality material for the Bayer process by increasing the A/S. Direct flotation has been shown to be an efficient method for the desilicating of diasporic bauxite ore (Wang et al., 2004; Xu et al., 2004), but reverse flotation has more advantages for this purpose, including less collector consumption, less foaming product and less effect on metallurgy (Liu et al., 2007; Hu et al., 2003; Hu, 2003; Luo et al., 2001)."

Jan 1, 2015

By A. T. Yu, K. A. Young, Ronald M. Hays, Sanford Terry, D. R. Campbell, J. K. Lovrien, W. L. Price, C. W. Matthews, W. R. van Slyke, S. P. Cole

Storage and transport systems are essential for mineral processing. Section 10 includes systems for storage and transport of dry bulk materials, slurries, and water necessary for operation of mineral pro¬cessing plants. All aspects of these systems are presented, including material characteristics; dry material placement in and reclamation from storage stockpiles and bins; dry material conveyance; hydraulics (liquid flow and pumping); slurry characteristics; slurry storage and reclaim, slurry flow (distributors, launders, and pipes), and pumping; water (primary and secondary process, reclaimed, fire, cooling, and domestic) supply, transport, and storage; equipment selection and sizing; power transmission; controls; and health and safety. The mate¬rials considered include crude ore; process and other water supplies; initial, intermediate; and final in-plant materials; finished materials; and tailings and other waste products. Section 10 is a compilation of practical operating data for engineers, technicians, and plant opera¬tors. For the design of mineral processing plants, including selection and sizing of equipment, the design engineer should consult with equipment manufacturers, suppliers, engineering firms, and plant op¬erators with specialized experience in particular materials handling methods. When unusual conditions are encountered, actual pilot or full scale testing may be required to insure adequate design. Operation of mineral processing plants is dependent on the proper engineering and construction of storage and transport systems for dry bulk materials, slurries, and water. It is obvious that processing plants cannot produce the required quantities of semifinished and finished products unless these material can be transported adequately to, through, within, and from the plant. Costs of storage and transport systems may exceed 50% of the total capital and/or operating costs. Considerable attention must be given to the design, layout, and engineering of these systems. These systems are interrelated with the mineral processing method and it is necessary to determine the best combination of mineral processing method and storage and transport systems. Storage and transport systems perform a major supportive func¬tion to mineral processing. The final selection of these systems depends on the final selection of the processing method and related systems (environmental control, tailings and waste disposal, etc.). The process¬ing method determines the characteristics of materials to be stored and transported; distances, elevations, flow rates for transport; and storage requirements. Flowsheet After selection of the processing method and related systems, a flowsheet must be developed. This flowsheet should indicate produc¬tion rate, percent solids or moisture, and specific gravity for all initial, intermediate, and final products or product flow streams. It also may be necessary to know the size analysis, chemical analysis, abrasiveness, and other physical characteristics of various product flow streams. The flowsheet provides basic information for plant layout, storage requirements, and selection and sizing of process and transport equip¬ment. Storage and transport systems often function improperly be¬ cause of inadequate flowsheet data or process revisions, resulting in improper equipment selection and sizing. Further details on plant design are presented in Section 33. After selection and sizing of process equipment, it is necessary to select the type of material transport equipment to be used for in¬plant materials handling as well as crude ore, tailings, and final prod¬ucts. The storage and/or surge requirements, including capacity and location, then are determined. Storage and/or surge capacity is neces¬sary for leveling production rate fluctuations due to variations in material characteristics; production scheduling; equipment mismatch¬ing, failure, or breakdown; and scheduled maintenance downtime. Variations in ore grindability will cause fluctuations in throughput or production rate for grinding mills and variations in ore grade will cause fluctuations in production rate for concentrating equipment. Variations in material moisture content and percent solids can have serious effects on the capacity of material transport equipment. In some cases, a blending system may be desirable or necessary to reduce variations and to obtain uniform production and/or metallurgy. Storage capacity often is needed because of different production schedules for various phases of the mining and mineral processing complex. As an example, the mine and coarse crushing plant may operate on a one- or two-shift-per-day schedule while the fine crushing plant and concentrator on a three-shift-per-day schedule. This would require storage between the coarse and fine crushing plants. Another example would be load-out storage where unit trains are used to haul concentrate or final products. The concentrator could be operated on a three-shift-per-day schedule while only I to 2 hr may be scheduled for unit train loading. This would require adequate load-out storage so that the concentrator can be operated continuously. Process equipment with mismatched capacities requires storage or surge capacity between the mismatched equipment to achieve oper¬ating efficiency. As an example, the fine crushers may have greater capacity than the rod mills. Storage between the fine crushers and the rod mills permits both the crushers and rod mills to be operated at optimum capacity with the crushers actually operating or running a lesser number of hours per day. Mismatched capacities for process and transport equipment also may require storage or surge capacity. Mismatching of equipment capacities most often occurs because of the difficulty in equipment sizing. Thus, the design engineer must anticipate where in the flowsheet these mismatching capacities are likely to occur while making every effort to assure that equipment is selected and sized properly. Equipment breakdown can cause major operating difficulties and lost production. These breakdowns can be reduced with adequate scheduled maintenance. Lost production due to nonscheduled down¬time caused by equipment breakdown can be reduced further by standby equipment and storage and/or surge capacity ahead of essen¬tial mechanical and electrical equipment. As an example, standby pumps and conveyors often are available as part of the in-plant trans¬port system. Storage and/or surge bins and tanks often serve dual functions, such as dewatering, mixing, and smoothing production rate fluctuations.

Jan 1, 1985

By H. G. Kok

The concept of mobile crushers is not new. Since their introduction about twenty-five years ago, mobile crushers have continued to gain widespread attention. Mobile crushers reduce minerals in the open pit mine to sizes which can be transported by belt conveyors thereby reducing or eliminating the need for truck haulage. Truck haulage is costly, often representing as much as 50% of the total mining cost. More than 80% of the cost of truck haulage is for fuel and lubricants, tire replacements, and operators' wages, and it can be anticipated that the cost of these items will continue to increase at a steady pace. Compared to truck haulage, transportation by belt conveyor is more energy-efficient, less labor-intensive, and less subject to inflation. Therefore, mobile crushers, used in conjunction with belt conveyor systems, offer one of the most effective available methods of reducing energy consumption and mining costs,

Jan 1, 1980

By F. W. Brackebusch

A unique machine has been designed for mining narrow veins. The machine, called the NONN, walks on the walls of the stope and carries a boom-mounted hydraulic impact breaker. The concept of walking on the walls allows an existing muck handling system such as LHDs to operate beneath the NOMN. The NOMM has four sets of legs which can be manipulated independently or concurrently to cause the carrier to walk in any direction and to turn sharp corners. The mining rate using the breasting method is targeted to be 25 t/hr.

Jan 1, 1990

By E. Stemn

Incident investigation is of utmost importance in most high-risk industries. This study was undertaken to study the content of past investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of 5 elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of 3 Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed. INTRODUCTION The importance of learning from incidents is well documented in the literature. For instance, some scholars regard learning from incidents as important for improving safety [1,2]. Thus, many organisations spend considerable resources in identifying lessons from incidents and subsequently on the process of improvement that follows the identification of lessons. It is therefore important for such organisations to determine the effectiveness of their learning from incidents processes, in order to identify specific areas where improvements are needed, so that interventions can be as specific as possible. The learning from incidents process models the plan-act-check-do approach of management systems, often consisting of four major stages, namely; data collection and incident analysis, planning interventions, implementing interventions and follow-ups and evaluation [3,2]. The investigating and analysis of incidents have been regarded as one of the vital stages of the learning process since it is the stage where lessons are identified [3,2,4]. It has also been noted elsewhere in the literature that results of the previous stage of the learning process are important for the next stage [3]. For example, ineffective incident analyses could result in the planning of ineffective remedial measures. One of the primary aims of incident investigations is to identify lessons from previous incidents which when implemented can prevent future recurrences or minimise the effects of future incidents. There is thus the need for organisations to assess the quality of their investigations periodically since it is one of the means they adopt to improve safety and the quality of remedial measures to some extent depends on the effectiveness of the investigations. Although previous studies [5,2] have assessed the effectiveness of the learning process, and some aspects of the learning process, such as incidents reporting, there is less focus on the effectiveness of incident investigations. The research described in this paper was therefore conducted to contribute to this gap, focusing more closely on incident investigation reports.

Jan 1, 2019

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By Greg Beckstrom

On Oct. 1-3, SME?s Twin Cities chapter (SME TC), in cooperation with the University of Minnesota ? Duluth?s Precambrian Research Center (UMD-PRC), cohosted a symposium on silica sand mining and processing. The conference was held at the Earle Brown Heritage Center near Minneapolis. The symposium was followed by a day-long field trip to operating mines, processing plants and loading facilities located in southwestern Wisconsin. Speakers and attendees at the symposium included university professors, industry experts, regulators, mining company representatives, equipment suppliers, consulting engineers and service companies. Approximately 320 people attended the conference. In addition, about 50 people who oppose mine development and the oil and gas industry showed up to voice their displeasure with the event and those companies that operate in this space.

Jan 1, 2012

By S. Koro

The current economic climate of low commodity prices and increasing costs has put a lot of pressure on mining companies to ensure their operations will survive through the current economic downturn. While history tells us that the cycle will turn around and prices will go back up again, how many mining companies will be left to take advantage of the next upturn? On average in Australia, the maintenance of mining equipment accounts for up to 50% of operating costs; which equates to nearly $15bn per year. In addition to trying to boost productivity, mining companies are also putting a lot of pressure on reducing costs; all with the intention of maintaining/increasing profit margins and thereby keeping shareholders ?happy?. The whole premise of our economy is based on ?growth? and ?profits?. Movements in the market place force mine owners to ?react? to short term fluctuations. And if that movement is downward; operations people at the sites are forced to start reducing costs. Is this cost reduction done in a logical, systematic way where all risks (short-, medium- and long term) are considered? Invariably, the answer is no! Short term ?fixes? are normally implemented with little, or no, regard for medium- and long-term impact. And the reason for this is that management is not fully focused on the long term; focus is mainly on survival. Decision making is driven by shareholder sentiment and history tells us that this is largely short-term. So given these paramteres to work within, what role can ?Asset Management? play in assisting management to meet shareholder and market requirements whilst still maintaining long-term viability of their operations (to the long-term benefit of shareholders dare I say). As maintenance costs account for nearly half the operating costs of mining companies; the ?smart? management of assets is not only crucial; it is essential for survival in today?s economic climate. What is asset management? Asset Management, according to the UK-based Institute of Asset Management (IAM) is ?the systematic and coordinated activities and practices through which an organization optimally and sustainably manages its assets and asset systems, their associated performance, risks and expenditures over their life cycles for the purpose of achieving its organizational strategic plan.? How important is asset management in today?s mining companies? IAM goes on to say: ?This definition of asset management represents a significantly greater scope than just the maintenance or care of physical assets, and is closer to the central purpose of an organization. Good asset management considers and optimizes the conflicting priorities of asset utilization and asset care, of short-term performance opportunities and long-term sustainability, and between capital investments and subsequent operating costs, risks and performance. ?Life cycle? asset management is also more than simply the consideration of capital costs and operating costs over pre-determined asset ?life? assumptions. Truly optimized, whole life asset management includes risk exposures and performance attributes, and considers the asset?s economic life as the result of an optimization process (depending upon the design, utilization, maintenance, obsolescence and other factors).?

Feb 23, 2014