Search Documents

By G. M. Molinda

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

Jan 1, 2008

A bearing isolator is a noncontact, nonwearing, permanent bearing protection device. It has a rotor and a stator, and the two are unitized, so that they do not separate from one another while in use. The rotor turns with a rotating shaft, while the stator is pressed into a bearing housing. The two components interact to keep contamination out of the bearing enclosure and the lubricant in. Bearing isolators do not require lubrication or any particular shaft finish or condition. The best bearing isolators are made of metal, usually bronze. They use a vapor-blocking feature that inhibits the free transfer of vapor contamination when the rotating equipment is cycled on and off.

Jan 1, 2004

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By Heather Wright

Shovel operators are one step closer to having a better tool to operate and monitor their equipment. The development of a unified shovel interface is proceeding into phase three, focused on producing a standard application programming interface (API) for connecting onboard devices. This solution will positively impact safety, performance and productivity, and is the result of collaborative work driven by the Global Mining Standards and Guidelines Group (GMSG). Proof of concept revealed During the spring of 2013, Peck Tech Consulting was engaged to develop the working proof of concept (POC) software implementation, which integrates multiple vendors? systems into a single interface using one-to-two displays. As a result, the GMSG developed a functioning, manipulatable, unified shovel interface proof of concept and unveiled it at the World Mining Conference in August in Montreal. The proof of concept effectively provides a unified operator interface that pulls together the many divergent systems onboard large shovels.

Mar 1, 2014

By R. S. Mateer

Linear programming on desktop computers is commonly used to optimize coal blending proportions. The objective function is usually the cost of the blend. The constraints consist of materials and heat balances as expressed as linear functions of the blend. This is illustrated in Example 1. Inclusion of a sulfur compliance constraint is more complex because the maximum permitted sulfur percentage is not a pre-specified constant. Rather, it is a function of the calorific power of the blend itself. The current limit of 1.2 pounds of sulfur dioxide per million Btu may be expressed as: Sulfur Max % = 0.6 • H/10,000 with H in Btu/lb.

Jan 1, 1994

By Mahmut Altiner

Magnesium is listed as a key critical raw material in a report by the European Commission that evaluated raw materials based on supply risk versus economic importance [1]. It has extraordinary properties, such as nontoxicity, inertness, high melting point, stability, low weight, chemical resistance, electrical insulation, optical transparency, corrosion-resistant behavior and refractory nature. It is widely used in the areas of agriculture; the environment, for antibacterial and water-purification purposes; electronics; automotive; drug delivery; ceramics; construction, as filler in brick; and concrete production, in the forms of magnesium oxychloride and magnesium oxysulfate. Magnesium oxide (MgO) particles can be produced through the calcination of magnesite ore at different calcination conditions depending on the desired quality of the product, classified as fused (2,800 °C), dead-burned (>1,400 °C), hard-burned (1,000–1,400 °C), or light-burned MgO (700–1,000 °C) [2]. However, the global availability of magnesite ore is limited.

By G. Soni

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model has been validated in a series of laboratory batch flotation experiments, in which mono-sized glass beads are used as feeds. The experimental results are in good agreement with model predictions both in terms of grade and recovery.

Feb 23, 2014

By Edward H. Jr. Boyle, Paul R. Thomas

Introduction It is estimated that nearly 40% of all the gold ever mined in free world countries has been produced by South African operations. There is concern that this immense productive capacity will soon decline. Such a decline could reduce world gold supply and lessen the ability of market economy countries (MEC) to exert the major influence upon the world gold market. This paper addresses three general issues concerning South African gold production: • How much gold remains to be recovered from the demonstrated resources of the 44 evaluated South African mines; • How long can production at current levels continue; and • What will be its cost. Table 1 provides production data on the world's 10 largest producers for the years 1971, 1981, and 1983. As shown, South African gold production declined significantly from 1971 through 1981. As of 1981, annual South African gold production had dropped by more than 311 t (10 million oz) in 10 years. Despite this, its mines still produced 656 t (21 million oz) that year, about half the world total. From 1981 through 1983, this trend was reversed. Annual South African gold production increased by more than 21.8 t (700,000 oz). The trend reversal was also evident in the US, Canada, and Australia. This illustrates the general, inverse relationship between gold price and gold production. In South Africa especially, as gold prices increased substantially during the 1970s, the average grade of ore mined (pay limit) was lowered as new, lower grade areas and materials were exploited. Gold production declined in volume. But gold revenues increased, and the lives of the operations were extended. The 1981-83 period was one of declining (US dollar-based, average annual) gold prices that resulted in increasing South African production as average ore grades were raised. South Africa currently accounts for 50% of world production (Fig. 1). Figure 2 illustrates South Africa's contribution to total MEC production in 1971 and 1983. Although South Africa's relative share of production has declined, it still represents the single most important source of new gold supply. In 1983, it supplied more than 65% of total MEC production. South Africa currently produces more than twice as much gold as the Soviet Union (ranked second in world production), and 11 times more gold than the US (ranked fourth in world production). Barring major discoveries, South African gold production is expected to peak in 1987 and begin to decline again throughout the 1990s. The rate of decline is ex-

Jan 11, 1984

By Yaxiong Wang, Yong Li, Yuedong Wu, Haigang Dong, Jiachun Zhao

A roasting-leaching process has been developed for concentrating platinum group metals (PGM) from a PGM-containing ferroalloy. The optimized roasting conditions used a NaOH-to-ferroalloy mass ratio of 1.2 at 600 °C for 2 h. The roasted product mainly comprised Na4SiO4, NaFeO2 and Fe2O3. The iron oxide and sodium silicate associated with the roasted product were leached in water and dilute sulfuric acid solution, while the PGM was concentrated in the acid-leached residue. A PGM concentration of 23.4% was obtained with assaying, and the concentration factor of PGM from the ferroalloy to PGM concentration was greater than 9.

Jun 14, 2021

By Jean E. Tilden

An investigation of several trace elements distributed among sulfide minerals from deposits located in the southeastern United States was conducted. The deposits investigated are distributed within both the Blue Ridge Province and the Piedmont Province, which are contiguous geographic provinces. Twenty five deposits were examined;' eleven in the Blue Ridge Province and fourteen in the Piedmont Province. Figure 1 shows the locations of deposits investigated. In the deposits investigated, the mineral phases examined were pyrite, pyrrhotite, chalcopyrite, and sphalerite. These phases were chosen because of their relatively widespread occurrence, although no pyrrhotite was seen in the Piedmont Province. A total of 116 polished surfaces of ores were prepared, and mineral phases were collected from these surfaces for analysis. Samples were analyzed for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. A total of 372 analyses were made. Trace elements were determined by atomic absorption spectrophotometry following standard procedures. In this study, trace elements are defined as those elements which are present in the mineral but which do not affect the chemical formula for that mineral. Lead is considered as a trace element only in ores where little or no lead sulfide could be identified as a distinct mineral phase.

Jan 1, 1972

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) remains a health concern in many underground metal/nonmetal mines, and has been regulated by the Mine Safety and Health Administration since 2002. While the NIOSH 5040 standard method for DPM monitoring is required to demonstrate regulatory compliance, the FLIR Airtec DPM Monitor can serve as complementary engineering tool. It is a handheld instrument that offers near real-time measurements. As part of an ongoing field study, the Airtec has been used to survey elemental carbon concentrations (a proxy for DPM) in an underground stone mine. Via “spot-checking” and more prolonged area monitoring, this effort was aimed at determining spatial and temporal DPM variation in several key locations. INTRODUCTION Diesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It is largely made up of elemental and organic carbon (EC and OC, respectively), which can be measured as proxies for estimating mass concentrations of DPM. The National Institute for Occupational Safety and Health (NIOSH) considers DPM to be a health hazard and potential carcinogen [1]. It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition, and retention in lung tissue [2]. Since DPM exists in both the micro- and nano-particulate ranges, it can surpass typical auto-immuno defense mechanisms that keep larger particles out of the respiratory system [2]. Relative to other occupations, the DPM exposure potential for underground miners is high because these individuals work in enclosed environments where diesel powered equipment is frequently used [3,4]. A variety of engineering and administrative controls have been devised to reduce DPM exposures in underground mines, and increased airflow is often a key component of control strategies. In large-opening mines, which are most common in the metal/nonmetal sector, DPM abatement via increased ventilation can be especially complex due to moving and controlling the large air quantities [5]. The Mine Safety and Health Administration (MSHA) has regulated DPM exposure in metal/nonmetal mines since 2002. The final rule limits personal exposure to total carbon (TC, which is the sum of EC and OC) to an eight-hour time weighted average (TWA) of 160 µg/m3. To demonstrate compliance, operators must use the NIOSH 5040 Method [6]. However, the Airtec DPM Monitor (FLIR Systems, Inc., Nashua, NH) was developed as an engineering tool to provide near real-time measurements of both EC and TC for tracking personal exposures [7]. The portable Airtec works by capturing DPM on a filter and successively measuring laser extinction on the filter as DPM accumulates; the EC fraction of the DPM is dark, and so as it accumulates the filter becomes darker and absorbs more laser light [8]. The laser extinction value is directly correlated to EC, but since EC and TC are generally observed in consistent proportions (i.e., TC = EC*1.3), the Airtec is also programmed to display TC as a TWA [9]. There have been multiple studies conducted to validate the Airtec and the instrument has been adopted by some mine operators as a tool for their health and safety programs [3,8]."

Jan 1, 2016

By Jackson G. Jenkins

Magma Copper Company's San Manuel SX-EW facility has operated since May, 1986. The original facility had a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solution from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing in-situ leach solutions. This paper focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research utilizing surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1993

By Steve Kral

In a lagging economy where profits are tight, businesses cut costs. No revelation there. The mining industry, though, has always looked for ways to reduce production costs — no matter the state of the economy or commodity prices. The fact is, when planning a new mine or the expansion of an existing one, mining companies gamble that commodity prices will be reasonably high when a project comes onstream. It takes millions of dollars and several years to bring a mine into operation. And a lot can happen economically between the time management gives the go-ahead for a new project and its completion.

Jan 1, 2002

By N. Rocco, G. Johnson

Implementation of post-closure draindown estimates for tailings facilities are important predictive tools for reclamation planning and often influence jurisdictional bonding. Simplified estimates of draindown have been proposed in the past but these methods are not able to capture many of the site-specific nuances as well as operational and material parameters that influence robust draindown estimates. This paper discusses an iterative approach that relies on unsaturated flow models to predict draindown rates and associated pond inventory water balances that track inputs into underdrain pond systems, solution storage volumes, implementation of active evaporation, and necessary recirculation of solution back to the tailings facilities. Specific design criteria such as climate, facility geometry, material properties, and initial conditions, as well as active closure operational considerations that can influence draindown estimate will be discussed. Concepts presented will be valuable for operators, designers, and regulators to guide closure planning and predictive analytical analyses that support draindown estimates.

Mar 2, 2022

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 11, 2018

By T. O. Llewellyn

The Bureau of Mines, U.S. Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8 to 10.2 percent P205 and 1.7 to 1.8 percent MgO. Chemical analyses of sized fractions indicated that no pebble concentrate (plus 1.2 mm) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid-fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0 to 31.3 percent P205 at flotation recoveries ranging from 72.4 to 96.1 percent of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36 percent. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3 percent P205 and 0.55 percent MgO could be produced with a flotation recovery of 89.9 percent. The MgO content of concentrates obtained from the Manatee No. I and Hardee samples was 1.20 to 1.36 percent, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 percent, but with a concomitant loss in phosphate recovery.

Jan 1, 1983

By M. Ribeiro, P. So, P. Wong

Electrowinning is a process by which metals, such as copper or nickel, are recovered from aqueous electrolyte solutions resulting from the extraction of the metal ion from an acidic or basic leach solution. The electrolyte or “pregnant” solution is customarily forwarded to an electrowinning "tankhouse." In the tankhouse, the metal ions are deposited on cathode plates by electrodeposition and then recovered from the cathode plates. Other processes may be employed with other metals, such as nickel, zinc, among others, to produce an electrolyte from which their respective metals are obtained. During the electrowinning (electrodeposition) stage, elemental metal is plated out at the electrowinning cathode and oxygen evolves at an insoluble anode. The evolution of oxygen gas forms bubbles which entrain strong acid electrolyte, carrying it into the air above the electrowinning tank in the form of a fine mist or spray when the bubbles break. An acidic mist is generated above the electrolyte. This mist or spray then spreads throughout the electrowinning tankhouse. The acidic mist is corrosive and a health hazard and can cause extreme discomfort to the skin, eyes, and respiratory systems of tankhouse workers, especially during hot weather conditions. Polyfluoroalkyl based products (PFAS) have been widely applied as anti-misting agents in the electrowinning of metals in an acidic electrolyte. Functionalized PFAS compounds, however, have come under increased scrutiny by the EPA due to their impact on human health and the environment. There remains need for improved acid mist suppression agents for electrolysis and electrodeposition, particularly for products free of fluoroalkyl components.

Feb 1, 2023

By John Fred Rivera

Since its inception during the hectic days of World War II, Kaiser Steel Corporation has developed and maintained a solid reputation as a progressive company with an incessant penchant for attempting innovative ideas to improve its stature in the American and world corporate framework. The very latest in technology is aptly demonstrated in the new Basic Oxygen Process recently placed into operation at Kaiser's huge Fontana Steel Mill. Daring ventures such as this and other developments on pollution control devices have propelled Kaiser Steel Corporation into the forefront as the largest steel producer in the western United States. Kaiser Steel's boldness and willingness to attempt new ideas and the very latest in technology is by no means limited to its steelmaking operation. It extends into every phase of Kaiser's corporate structure.

Jan 1, 1979

By J. Chai, H. H. Sedarat, Gary J. E. Kramer, A. Kozak

Precast concrete segmental lining systems have been gaining widespread use in seismically active areas and a single-pass version of such a system has been developed for use on the Silicon Valley Rapid Transit (SVRT) Project in San Jose, California. The response of tunnel linings to seismic shaking is often predicted using engineering judgment, elastic closed-form solutions and numerical modeling. Such analyses generally assume a continuous structural system and hence do not explicitly model the behavior of the jointed segmental lining. A number of analyses were performed to predict radial and circumferential joint behavior during seismic ovaling and wave propagation. These analyses included a complex, three-dimensional finite element based ground-structure interaction model that incorporates inelastic constitutive soil behavior, cracked concrete properties and no-tension, frictional segment joint surfaces. The paper discusses the results of the analyses and provides guidelines for the design of precast systems in zones of high seismicity.

Jan 1, 2007