Search Documents

By Robert K. Jones

Filter media can be defined as that material which effects the removal of finely divided solids from a fluid. Thus the removal of dust from air or turbidity from water, for example, can be the result of passing the fluid through a properly supported filter media. Since filtration in one form or another has been practiced since pre¬historic times filter media have been made from an extremely wide variety of materials. Vegetable and synthetic fibers (used loose, or formed into papers, felts or cloth) sand, ground coal, diatomite, perlite, wire cloth, porous metal, and bonded aluminum oxide are among the more important materials used today.

Jan 1, 1961

By R. J. Good

It is well known that the elimination of impurities such as iron pyrite, shale, clay, silica, etc., from coal, by floatation [Sun, 1954; Aplan, 1983] and selective oil agglomeration [Keller and Burry; 1990] depends on the fact that coal is hydrophobic, and the impurities are hydrophilic. The water contact angle has long been used to evaluate the hydrophobic nature of coal, first by Brady and Gauger (1940), who demonstrated that the contact angle of water on coals increases with rank, and passes through a maximum at about 88% carbon. Brown (1962) found that the contact angle of coal decreased with increasing ash content. Sun, and also Aplan, have reported a direct relationship between values of the contact angle and rank, and have related the contact angle to coal floatability. Horsley and Smith (1951) first demonstrated that the captive bubble contact angle may be used to characterize the hydrophobicity of a coal containing more than 80% carbon DAF, while Parekh and Aplan (1978) have shown that the sessile-drop technique may be used to evaluate the hydrophobicity of coal of any rank.

Jan 1, 1992

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By Frederick B. Brien

For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present-low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Bolivia today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since appropriate heavy liquids are available and with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined.

Jan 1, 1964

By R. Bhaskar

The results of an experimental study on the dispersion and deposition characteristics of fine coal dust in mine airways are presented. Experiments were conducted at various flow velocities using bituminous and semi-anthracite-coal dust which had a large proportion of dust in the respirable size range. Cross sectional variations in the concentration of dust at various points in the airway were also measured. Instruments used in the experiments included gravimetric samplers and impactors. Concentration measurements were made both for the respirable and total airborne dust. The experimental design, sampling procedures and results are discussed. The study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways.

Jan 1, 1986

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By C. Caceres

Fibre reinforced shotcrete in combination with other types of support systems is becoming the leading support method for underground excavations, especially those present in low quality rock masses. Sudden or rapid ground support failure can expose workers to safety hazards, damage to equipment and others resulting in production interruptions that will impact the cost of operation. Knowing the peak and post-peak strength characteristics of the support system over time are of major importance. Round Determinate Panel Testing of fiber reinforce shotcrete is the primary test used by the mining industry to determine strength characteristics; however, the tests are costly and significant manpower is required in a mine environment to build, store, handle and test the panels. For these reasons numerical modeling can result in an effective method to produce realistic results. This paper examines the strength characteristics Round Determinate Panel tests and its ultimate application in underground excavations, using Itasca?s three dimensional particle flow code (PFC3D).

Jan 1, 2010

By Melvin W. Dadd

[One of the major problems in the purchase and sale of coal shipped in lake or ocean going vessels has always been the difficulty in obtaining a true analysis of the shipped coal?s quality because of faulty sampling by manual methods. As long as coal was sampled according to standards set up by ASTM methods designated D 492-48 there generally were no quarrels with the results obtained. However, due to varied weather conditions and because of the large number of cars sampled, there is no assurance that prescribed manual methods of sampling will always be followed. Because of this problem, the organization previously called American Coal Sales Association, now part of the National Coal Association, set up a committee compose of representatives from coal producers, coal shippers and coal consumers to study this sampling problem and to devise, if possible, a means of sampling on the high lift dumpers which could be automated so that a; true sample of the coal as loaded in the railroad car could be obtained.]

Jan 1, 1962

By George A. Savanick

Borehole (slurry) mining, in which a tool incorporating a water-jet cutter and a downhole slurry pump mines phosphate through a borehole, was field tested in northeastern Florida as part of a Bureau of Mines program to increase the domestic availability of critical minerals. Approximately 1700 tons (1.54x106 kg) of phosphate ore were mined at 40 tph (10.1 kg/s) from a depth of 250 ft (76 m). The borehole was filled with water during mining for roof support and to assist slurry pumping. Underwater cutting was enhanced with an air-shrouded water jet. Mined cavities were backfilled to prevent subsidence after abandonment. Roof subsidence during mining was avoided only when the cavity was filled with water. Environmental monitoring before, during, and after mining included hydrological studies and measurements of water quality. Significant water quality changes occurred only in the zone being mined and were confined to the immediate area of the borehole.

Jan 1, 1983

By Yuemin Zhao, Daniel Tao, Xinxi Zhang, Qingru Chen, Maoming Fan, Zhenfu Luo, Xiuxiang Tao, Guohua Yang

Coal is currently cleaned with the minimum of size reduction, fine particle processing, recovery, and tailings disposal are major problems. Adequate water resources are not always available. For example, two thirds of China's coal is located in arid areas. Hence, dry separation provides an alternative approach. Of the dry coal separation methods available, air dense-medium fluidized beds have been used to separate 50~6mm coal efficiently. However, excessive bubbling and back mixing of the separated solids in the air-dense media fluidized bed causes the high lower size limit of 6mm for the feed material, this affecting the preparation efficiency. Based on prior study on air-fluidized dense media for 6~50mm coal preparation, this paper presents methods and test results on the fine coal dry classification, static electricity beneficiation of 0~0.5mm coal, and magnetically stabilized fluidized beds for separating 0.5~6mm coal.

Jan 1, 2005

By R. V. Ramani

In this paper, the application of the concepts of reliability engineering to the evaluation of longwall system performance is illustrated with data from an operating longwall face. A number of cases are analyzed to highlight the impacts of longwall equipment, geological conditions and outby haulage on systems reliability and availability.

Jan 1, 1988

By Z. Jin, D. DePaoli, P. Zhang

"Phosphorite, or phosphate rock, is the most significant secondary rare-earth resource. It contains high amounts of phosphate-bearing minerals along with low contents of rare earth elements (REEs). In Florida, about 19 Mt of phosphate rock are mined annually and most are used to manufacture fertilizers using a wet process, in which sulfuric acid reacts with phosphates to produce phosphoric acid and phosphogypsum. In the wet process, REEs are also leached out into solution and eventually get lost in the leaching residue and phosphate fertilizer. Recovering REEs from Florida phosphate rock in the wet process will be beneficial to broadening rare-earth availability, improving the quality of phosphoric acid product and protecting the environment.This study focuses on the influences of wet-process operating conditions on REE leaching efficiency. The results indicate that REE leaching efficiency increases with phosphoric acid addition in the initial pulp. At a temperature of 75 °C, a stoichiometric ratio of sulfuric acid (H2 SO4 ) to calcium oxide (CaO) of 1.05 and a weight ratio of liquid to solid of 3.5, REE leaching efficiency reached a relatively high value of 52.82 percent. The trends of REE leaching efficiency were similar to those for phosphoric acid (P2O5 ). Extensive tests on the leaching residue showed that during leaching, about 90 percent of the REEs were released from the phosphate rock but only 52.82 percent ended up in the leaching solution. This phenomenon can be attributed to two factors: (1) the effect of phosphate ions (PO4 3-) in the solution, which caused REE ions to form REE phosphates and be precipitated into the leaching residue, and (2) the influence of large amounts of anions such as sulfate (SO4 2-), dihydrogen phosphate (H2 PO4 -) and hydrogen phosphate (HPO4 2-) anions as well as the polar molecule H3 PO4 , which surrounded the REE cations and formed an ion atmosphere that prevented the PO4 3- from contacting and combining with REE cations. Interaction of these two opposite effects determined the REE distribution between leaching solution and residue."

Jan 1, 2017

By Louis H. Meece

The romance of the River lives on in the tales of Mark Twain; and many Americans still think of the Mississippi River in terms of the steamboats loaded with passengers, gamblers and cotton. Yet for many years, coal has been a major cargo on the American waterways. Currently, about 100 million tons a year of coal is handled in some part of its journey from mine to destination by barge. The bulk of this traffic has been on the Ohio River System and the Upper Mississippi River System in years past. Now we have a new entry. Over the past 10 years various movements of coal have developed down the Mississippi River to power plants at Memphis and along the Gulf Coast, and a small amount of metallurgical coal has moved down the Mississippi River for export to Japan since 1970. But in 1980 a brand new player came on the scene. 1980 was a momentous year for the American coal business. Historically, we have exported about 50 million tons a year of metallurgical coal to the world's steel mills. Just before and after World War I, we also had a fairly healthy export trade in steam coal; and again in the late forties, we supplied large amounts of coal to Europe until domestic production could recover from the ravages of World War II. But since the early fifties, the name of the export game has been metallurgical coal. Starting in the mid seventies, something began that was almost totally missed by the American coal industry; and that was the growth in the use of coal first in Europe and now in the Far East as a steam product and as an alternative to petroleum products. As these world coal markets began increasing, the U.S. at first was thought to be noncompetitive because ocean rates were still very low. For example, as recently as 1977, Australian coal could be moved all the way from Australia to the Gulf Coast for $12.50 per metric ton. Coal exporting countries were Poland, Australia and South Africa, except for the continuing exports of U.S. high quality metallurgical coal. But then came the second oil shock, and all of the sudden that $12.50 rate from Australia to the U.S. Gulf became $25.00. And then suddenly and almost unrecognized by the American industry, American coal was in fact competitive at overseas destinations because of the drastic change in trade patterns brought on by the doubling and tripling and quadrupling of bunker fuel prices for ships.

Jan 1, 1982

By Graham A. Brown

Activities in offshore mineral exploration In Australia are increasing almost daily, at such a rate that this report will rapidly become out of date. At the time of writing, February 1967, there were no commercial discoveries of offshore minerals reported in Australia, although there has been definite encouragement in many fields. While this initial encouragement has not revealed any commercial mineral deposits offshore hopes are running high in Australia for success in 1967. Why should mineral deposits be expected offshore in Australia in the first place? The reasons are many. The minerals to be discovered also are many. The reasons are based on the history of alluvial and beach mining activities in Australia's past and at the present time, and on the physical environment of the vast Continental Shelf which surrounds the continent. A brief examination of the two primary features which are necessary before offshore mineral exploration can be contemplated should be, undertaken. Two favourable environments are necessary; firstly a Continental- Shelf to form a physical environment for the accumulation of the mineral deposits, and secondly a favourable political-legal environment to give the exploration companies adequate protection during exploration, and suitable long term arrangements for the exploitation of the deposits after discoveries have been made. Australia is well endowed with both of these.

Jan 1, 1967

By C. Sampaio, C. Petter, M. Veras

"INTRODUCTION Use of sensor technology applied to the gravimetric beneficiation is intended for the selective preconcentration or separation of various minerals. Sensor Based Sorting (SBS) uses sensors to identify the particles and separate them by a mechanical process (flap) or pneumatic ejection valves (Wotruba et al. 2014). The principle of the SBS technology to separate mineral particles consists of three phases which cover feed,detection and separation. (killmann, 2009 Apud nienhaus et al. 2014). The applicability of the technique in an early stage of beneficiation enables free particles and poor grade to be a part of the process. The mass of tailings to be processed can be removed at the initial stage to save energy, water and equipment maintenance (Wotruba et al. 2014). Lindner (2010) suggested that the use of SBS technology would only will be possible if there exsists an electromagnetic interaction in all the wave spectra interacting with the solid ore. The interaction of electromagnetic waves depends directly on the characteristics of the material. The material receives a spectrum of electromagnetic waves by irradiation and this results in a reduced wavelength with differing types radiation such as fluorescence, reflection, remission, absorption, transmission and transmission. The frequency of the wave spectrum varies between 1000 and 1020Hz, illustrated by the data in Figure 1, which shows that each type of sensor emits a wavelength inversely proportional to the frequency ranging from 10-11pm to 104km, and the frequency that varies between EHz 103 and 1020kHz. The difference between the electromagnetic spectrum variations can only be visible to the human eye at wavelengths with intervals between 380nm and 780nm (Wotruba et al. 2014). One of the main advantages of operating with imaging sensors is the versatility of the images which can take on zero, one, two or three dimensions shown below as a point, a line, an area or a spatial image, as illustrated in Figure 2. According to Schubert (1988), to separate a mineral particle it is necessary to follow the characteristics of mineralogy, physics and chemistry with or without use of water. The use of new technologies can help reduce operating costs and improve utilization of mineral resources."

Jan 1, 2016

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By R. Jin

The hydrophobicity of six coals ranked from lignite to anthracite is studied through contact-angle measurements, bubble attachment-time measurements, FTIR spectroscopy, and Hallimond-tube flotation. The preliminary study shows that the hydrophobicity of coals can be told by the bubble attachment times of coals (a kinetic criterion) or by the contact angles (an - equilibrium criterion). A general agreement between flotation response of coals and measured bubble attachment times or contact angles is observed in the present study. However, the study also shows that the hydrophobicity of coals can be predicted by FTIR spectroscopy work with proper manipulation of the spectra. Both hydroxyl and carboxyl groups in the coals are proven by FTIR work to be responsible for the change of coal hydrophobicity. A new criterion for the hydrophilicity index of coals from FTIR spectra is introduced through the study.

Jan 1, 1987

By F. C. Appleyard

A couple of miles southwest of the town of Saltville in the western tip of Virginia is a little village called Plasterco. Gypsum has been produced in this area since about the year 1815, being originally found as small outcrops at the surface. Production in the early days was very small, and the use of the mineral was limited to that of "land plaster" or ground gypsum which was spread on the land to sweeten the soil. In the late 1800's, a small calcining plant was constructed and the production of gypsum plaster began. About this same time, the surface rock was depleted and it became necessary to begin underground mining operations in order to maintain a continuous supply of raw material. The United States Gypsum Company became interested in this property in 1909, and has operated there ever since, having enlarged the calcining mill and built a plant for the manufacture of gypsum wall-board in the middle 1920's. Production of gypsum continues from underground' mining operations, and the present mine at Plasterco is now about 1,000 feet below the surface, making it the deepest gypsum mine' in the world.

Jan 1, 1965

By K. F. Unrug

The research work reported in in this paper deals with the monitoring of roof behavior in a drift mine located in Eastern Kentucky operating in the Coalburg Seam. The thickness of the seam at the monitoring site ranges between 9 and 10 feet with the immediate roof changing from sandstone to shale then back to sandstone. Shale thickness varies between 0 and 2.5 feet. The characteristics of the immediate shaly roof were monitored with 38 dynamometers which were set up in three survey lines to cover the entire range of shale distribution. The dynamometers are capable of providing accurate load readings in the range of +/- 5 pounds. To closely observe the contribution of moisture toward roof deterioration the dynamometers were set up in intake and neutral airways. A television borescoping camera was used in conjunction with the dynamo- metric instrumentations at pre- determined observation holes to physically observe and record the separation process of the shale and sandstone stratum with respect to time. Monitoring took place between January 1985 through January 1986 in order to cover a full cycle of dry and wet mine conditions associated with the seasonal changes. Analysis of the data show a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1986

By E. W. Davis

This paper deals with the role of the Maintenance Department in a milling operation; specifically, the Mines Development, Inc., processing plant at Edgement, South Dakota. The goal of very maintenance department is the smooth and uninterrupted operation of the plant it serves, To achieve this goal, maintenance men adapt various features and procedures into a program designed to fit the characteristics of their particular plant operation. A few of the basic elements of a sound maintenance program are: 1, A periodic preventive maintenance schedule. 2, A systematic inspection and lubrication procedure. 3. A training program for maintenance personnel. 4 A good equipment-history file system, 5. A carefully planned spare parts inventory.

Jan 1, 1962