Search Documents

By Stanley C. Suboleski

The increase in productivity which has been achieved in mining during the past two decades has been attained largely through the replacement of manpower with electrical power. Power demands should continue to increase, requiring electrical distribution systems to be well planned to avoid inadequate voltage levels caused by underdesign and excessive costs resulting from overdesign. To aid the mining electrical engineer in designing proposed power systems or analyzing changes to existing systems, a digital computer program has been developed. This program will analyze alternating or direct-current networks with up to 10 voltage sources, 75 loads and 300 total segments. A maximum of nine levels of voltage is permitted in the system. This project was part of a package of programs developed at Virginia Polytechnic Institute (WI) for the mining industry under sponsorship of the Office of Coal Research. Included in this package are also programs to: 1. Schedule mine production and predict cost of mining 2. Simulate rail haulage systems 3. Simulate belt haulage systems 4. Analyze ventilation networks 5. Analyze pumping networks These programs are available from the Department of Mining Engineering, VPI, Blacksburg, Virginia 24061 for a nominal processing cost.

Jan 1, 1970

By Zhe Wang, Tichang Sun, Yongqiang Zhao, Zhengyao Li

Coal-based reduction followed by magnetic separation is a promising technology for processing refractory iron ores. Analysis of the size distribution of metallic iron particles is an effective approach for exploring the mechanisms of coal-based reduction. As metallic iron particles exhibit very complex shapes compared with nature ores, approaches for measuring and characterising metallic iron particles still remain unclear. In this study, the size of metallic iron particles was measured and characterised using manual point-counting by optical microscopy technics and image analysis. The effects of CaF2 as an additive on behaviour of the particle size distribution (i.e. mean size and cumulative frequency distribution) were also determined. Results indicate that CaF2 had a significant effect on the growth of metallic iron particles. When the CaF2 dosage increased from 0 to 8%, the mean size according to the area method increased from 9.03 to 16.28 μm, while the promotion effect gradually weakened and generated many fine metallic iron particles when the CaF2 dosage exceeded 8%. An increase in CaF2 dosage also led to cumulative distribution curves gradually shifting to the right mainly because F− can break the crystal structure of each phase during the carbothermic reduction of titanomagnetite and reduce the stability of the lattice structure, thus reducing the melting point and accelerating the growth of metallic iron grains. Compared to different measuring methods, the area method is a more suitable approach for measuring and characterising the size of metallic iron particles.

Sep 18, 2020

By Leon D. Keller

Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units are currently in operation on magnetite, varying in size from 16 ft diameter circular unit to a 25 ft by 100 ft rectangular unit. Additional units up to 38 ft diameter are under construction. Depending upon the application in the flowsheet, upgrading-varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to economically remove as much silica as possible may not be fully appreciated. These figures pertaining only to transportation may be thought-provoking. If a 10,000,000 ton per year plant could reduce the silica content of their concentrate by 17, a savings in boat freight alone would amount to 100,000 tons at $2.00 per ton annually.

Jan 1, 1963

By M. E. Kuchta

Surface coal mine design can be facilitated with the use of an interactive graphics personal computer program. This mineral inventory and planning program (POLY CALC) is described and its use is illustrated with a case study. The case study deals with investigating a stripping sequence and associated dragline stripping requirements.

Jan 1, 1986

By Ashraf A. M. A. Wali

Many of the economic resources of Egypt have been recognized and exploited for thousands of years (e.g. gold and copper). Most of these minerals, particularly those from hard-rock sited deposits, are found in complex form along with other components while those present in sedimentary sequences are largely in simple compounds or as native elements. Recognition of their characteristic settings (structure, basin development, environment of formation etc.) is the main clue in predicting and locating their presence. The main economic minerals exploited in Egypt today come from sedimentary sequences and include sodium and potassium chlorides, gypsum, sulfur, and sedimentary iron ores. Large amounts of low grade sedimentary phosphates are known but are not of economic value at today's prices. Recent intensive investigation in the north-eastern Sinai (EI Arish) and along the southern coasts of the Gulf of Suez has revealed new and extensive sulfur and chloride deposits, and considerable oil and gas are now being exploited from closely related sediments. Tin is the only mineral that is produced from hard-rock sources, and gold and copper deposits are present but not of high enough grade to be economically viable. However, a significant part of Egypt has not yet been studied in enough detail to close the door on future discoveries. Another point of considerable geological interest is the presence of diverse, modern evaporitic settings, from which we may draw the analogs for many of the older gypsum, anhydrite, chloride and sulfur de-posits. In fact these analogs are so well displayed that both the Sinai and Gulf of Suez-Red Sea evaporites (Middle and Upper Miocene) can be readily compared with these modern deposits.

Jan 1, 1990

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990

By Robin P. Gardner

The mechanistic or phenomenological approach to ball milling involving the, concepts of particulate selection and breakage functions with particle population balance models has been well established over the past decade (c.f., the review articles by Austin (1) Herbst and Mika, (2) and Snow (3)). Initial efforts to apply this approach concentrated on batch milling, but since most milling in industrial practice is continuous, much recent research has been directed to extending this approach to continuous milling. The primary difference between batch and continuous milling processes is the relative importance of material mixing and transport in the mill in the latter case. Much analytical (4-8) and some experimental (9-15) work on the effect of mill mixing and transport on milling has been recently reported. Much of the analytical work has naturally centered around extension of the well-developed concepts that have been applied to chemical reactors, (16-18) Fortunately, it has been found(1) that most milling processes are analogous to first-order chemical reactions so that the combined effects of material transport and reaction (breakage) can be handled by the relatively simple segregated flow concepts. (8)

Jan 1, 1973

By Susanne Pignolet

Ore microscopy has been applied to the complex lead-zinc-copper-cobalt-nickel ores from the Madison Mire in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposits, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate. In ores from higher stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the recovery of the cobalt and nickel in bravoite, even though some of the fine-grained bravoite will not be recoverable. Other textures which may result in potential beneficiation problems include coatings of covellite on chalcopyrite and inclusions of sphalerite in galena.

Jan 1, 1983

By Paul D. Tomlingson

Maintenance costs in the mining industry often account for as much as 18-20% of total operating costs and with the cost of labor and materials rising, they threaten to become an even larger percentage of the total. Yet, without an effective maintenance program costs can soar beyond what they would be without a program. In other words, when production equipment is down, there is no production and no product to sell in the marketplace. This cost of downtime in lost product far exceeds the actual cost of maintenance, which is defined here as labor and materials. Thus, mine management must have an effective maintenance program to avoid downtime and meet production targets. Attaining an Effective Maintenance Program Many mine management and operations supervisors believe that an effective program is a function of how hard they push maintenance. Yet, when vital production equipment is inoperable and production is lagging, no amount of pushing helps. In actuality, maintenance has little control over its own destiny and needs support from other departments to deliver good service. Success of the maintenance program depends on gaining control of those factors that directly influence maintenance. Consider the following. Organization-The maintenance organization must be structured for maximum responsiveness to production needs. Unfortunately, some needs are immediate and many are unknown in advance. The maintenance department has little control over them. These outside influences limit the department manager's ability to control his own organizational structure. Preventive maintenance procedures-Routine lubrication, equipment inspection, minor adjustments and the like are controlled mostly by maintenance. Yet, scheduling preventive maintenance depends also on the availability of equipment controlled by other departments. Planning-The purpose of planning maintenance jobs is to ensure that the best use is made of maintenance resources. If the production department creates an environment of running repairs and emergencies, there can be little planning. Even well-planned jobs will suffer if there is less than full cooperation in carrying them out. As a consequence, the maintenance department is not blocked from planning, but the value of its planning is reduced. Scheduling-Maintenance scheduling should be a joint effort. Although maintenance does the planning, production must agree to the scheduled maintenance of its equipment. Workload-As a service organization, the maintenance department has limited control over its workload because it must consistently respond to other department's demands. At best, maintenance controls only the fixed portion of its workload-utility work, janitorial service, maintenance shop work, and assigned repetitive and preventive maintenance duties. Unscheduled and emergency work are initiated by operations. Major maintenance actions require full cooperation. Labor productivity-The effective use of labor is tied to other key functions of maintenance. These include organization, preventive maintenance, planning, scheduling, and emergency work. An area type organization, for example, can often respond more quickly to immediate needs than a centrally controlled maintenance group. Yet, area maintenance can result in lower labor productivity unless tight control is exercised. One of the advantages of a good "detection-oriented" preventive maintenance program is early discovery of problems and better opportunity to schedule corrective work in advance. Under planned work conditions, use of labor can be more productive. Complete planning and scheduling can minimize time spent on each job, increase effectiveness of supervision, and improve labor productivity. Finally, if emergency work is minimized, there are fewer delays, less lost time, better coordination, and more productive use of labor. While labor productivity is an important factor in carrying out maintenance, it also is influenced by outside factors. However, few realize the impact of being able to improve maintenance productivity. By improving the productivity of 30 men from 30% to 40%, maintenance could accomplish the same work value as if it had added 7.5 men working at 40% productivity. 30 (1800) (40%) = 21,600 man-hr/yr 30 (1800) (30%) = 16,200 man-hr/yr Difference = 5,400 man-hr/yr 1800 (40%) 7.5 men Leadership-The maintenance department can have significant control over its own leaders, the front-line foremen, but they must

Jan 12, 1982

By William F. Tanner

A river delivers a given load of sand, and hence of heavy minerals, into the sea into which it empties. This load is fixed by drainage basin characteristics and processes. Wave energy available for redistributing that load is fixed in an entirely different way. An equilibrium diagram of these two parameters (load versus energy) permits a tentative prediction of what will happen to the heavy minerals. The Chattahoochee River delivers a load which, over the past few thousand years, appears to have been greater than the available coastal energy could handle. As a result, much of the sand has been accumulated in various delta-margin features: barrier islands, beach ridges, and large furrowed off-shore shoals. The bulk of the trapped sand is found today in the shoals, which are attractive deposits for possible exploitation. If coastal energy levels are high enough to move the total load delivered by the river, accumulations of sand (and hence of heavy minerals) should be sought in the down-drift direction. Energy levels are rarely constant over any great length of coast. Decreases in energy may be due to widening of the shelf, convexity of, the shore, restrictions on the fetch, wave decay, or other causes. Such decreases result In deposition. Hydrodynamic mapping of coastal areas, as outlined here, should prove useful in the location of additional reserves. Part of this type of work can be done on maps, charts, and air photos.

Jan 1, 1962

By M. L. Rizzone

Since time immemorial, Mother Nature has been transporting slurries with both air and water serving as the carrier medium. Consider for example the formation of the continental shelves off our coast lines which are being formed by rivers emptying erroded land surface and depositing it into bays and gulfs. As the erosion processes take place, the fines are suspended in water which flows in streams and rivers and deposits where the velocity of the flow reduces sufficiently to allow the fines to settle out. The same process in some crude form is provided when one hoses his driveway or patio and moves dirt so as to provide a cleaning action. These examples illustrate rather crudely how the formation of slurries allows for the transport of solids. In recent years, this mechanism has become fairly well understood and slurry pipelining of many materials is now a vivid reality. The movement of liquids in pipelines necessarily occasions the use of pumps for the purpose. Those of us who have had some rub with the petroleum industry are familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well the circulating fluid utilized to remove chips which are cut by a drill bit from holes drilled deep in the earth is called drilling mud. This substance contrary to what the name might imply is usually a fairly sophisticated material designed to develop certain characteristics which are desirable in the drilling process. The particles which have been cut by the drill bit are suspended in the moving column of fluid and brought to the surface and deposited. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits. However, it is impractical to remove the fines completely from the drilling fluid and as a result they are pumped through the mud pumps back into the circulatory stream.

Jan 1, 1969

By H. G. Fleshman

Thousands of years ago, Chinese water well drillers developed a technique for punching holes in the ground by lifting massive metal bits and letting them fall against the rock. With diligence, they could pound away about 2 feet a day. The Chinese drillers pounded holes in the ground this way for almost 2000 years. In the 1860's, French water well drillers developed a perforated bit moistened by fluids pumped into the hole through a hollow rod. The fluids carried the cuttings from the hole and spared the Frenchmen the task of bailing them out by hand.

Jan 1, 1986

By Thomas F. Torries

It does not take sophisticated economic analysis to determine the current status of nickel production and demand (Figure 1). One only needs a quick glance at the balance sheets of the major nickel producers to learn that prices are down and profits are supressed to the point where they are major losses. Operations have been closed, and those remaining in production have reduced output. What Is now of interest Is, when will the nickel market improve and to what degree? The purpose of this paper is to attempt to answer these questions. This will be done by the normal method of projecting nickel demand, chosing a production scenario, and analyzing the results.

Jan 1, 1982

By Jerry F. Fountain

Variations in ore grade, mineralogy, and copper pricing structures over the life of the Inspiration mine have mandated many modifications to the treatment methods to maximize process economics. In the 1970's, copper prices generally declined, while inflation, wages, and interest rates increased. A metallurgical treatment route had to be developed for this continuing economic climate which would be capable of minimizing labor, energy, and capital cost requirements. After many years of development, the patented "Ferric Cure" process was introduced to satisfy these requirements. This dump leach process for treatment of mixed oxide/sulfide ore includes: strict mineralogical control of ore placed for leaching, controlled leach pad construction, solution saturation and curing of the pads with higher acid concentrations, and, finally, rinsing of the cured pads for removal of dissolved copper. Leach solutions, high in sulfuric acid during the cure application and low in sulfuric acid during the rinse, contain sufficient ferric iron to enhance the leaching of chalcocitic sulfide minerals.

Jan 1, 1983

By Drummond Earley III

The U.S. Bureau of Mines is currently conducting laboratory experiments to study the reactions occurring during in situ leaching of oxide copper ores hosted by biotite-poor granite and biotite-rich granite porphyry. Detailed pre-leach and post-leach petrographic examinations of the rock samples are combined with the leach solution chemistry resulting from core leaching experiments to enable an evaluation of the various reactions which are responsible for the observed fluid chemistry. The information resulting from these laboratory studies is being utilized to support the design of the Bureau's ongoing field research project at the Santa Cruz deposit near Casa Grande, AZ. Atacamite and chrysocolla are the primary copper minerals present in this deposit, and both are readily soluble in the dilute 5% sulfuric acid solutions used in these experiments. In addition to the dissolution of copper minerals, biotite dissolution also occurs during the experiments, contributing K, Mg, Fe, and Al to the leach solution. The biotite dissolution appears to be non-stoichiometric, as it is progressively altered to vermiculite and finally, amorphous silica. While K, Mg, and Fe concentrations in solution steadily increase with time, Al quickly reaches a maximum, and then remains relatively constant for the remainder of the experiment. This suggests that Al saturation is achieved, and this Is supported by the presence of precipitated Al sulfate and aluminosillcate clay mineralization in the post-leach rock samples.

Jan 1, 1990

By Karl J. Benecke

Though the first patent on a bucket wheel excavator was granted in 1881 in the U.S. this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with the development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generating, despite the low heating value of German lignite in the order of 8500 kJ/kg (3600 BTU/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is in the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output open pit mines. The largest one, Fortuna Mine in the Cologne district, produced a, total of 45 000 000 t lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95 200 000 bank m3 equal to 200 000 000 t overburden had to be removed to accomplish this lignite output. The largest BWE (Fig. 1) ever built is working in the Fortuna Mine, too. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 t, its wheel diameter 21.6 m, as high as a 7-storey building.

Jan 1, 1977

By C. B. Clemmens

Accurately predicting ground control conditions before mining requires a comprehensive exploration approach including photogeologic mapping (satellite and low altitude), delta modeling and, particularly, geophysical logging. In situ properties, density; strength indices; grain size; clay content; and aquifer location, can be estimated with this inexpensive technique. Geophysical measurements can be spot-checked by field or laboratory tests on core samples and by hydrologic (pressure) testing. Each phase of drilling should be accompanied by refinement of the delta model, facilitated by log signatures. Measured properties can then be projected into geologically similar areas. A properly planned program will delineate both the "worst-case" and normal support conditions. Suspect areas can be avoided by mine layout and the mine plan can contain support contingencies for anticipated trouble spots.

Jan 1, 1985

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By Yong-ping Wu

Based on the rules of strata behavior and the characteristics of rock movement, the elementary problems of using fully mechanized coal mining techniques in steeply dipping coal seams are described. A model of the "surrounding-support-rock" relationship is made. The support systems stability during fully mechanized mining of steeply dipping coal seams is studied. Then, a practical engineering example of the fully mechanized mining of a steeply dipping seam is presented. The seam used in the example is in the Lushuidong colliery, which is administrated by Huaying Mining Bureau, Sichuan Province.

Jan 1, 2003

By W. L. Freyberger

In many papers concerned with fundamentals of the froth flotation process, authors have considered the contents of a flotation cell to be comprised of two immiscible phases, the froth and the pulp. I (Of course, each of these phases is in turn made up of several solid phases plus air and water.) This generalized concept of the flotation system can be extended by considering the cell contents to include two phases: an extracting phase, the air bubbles plus the collector, which removes a selected mineral component from the second phase, the ore pulp. Thus, there is an analogy between a flotation system on the one hand, and chemical extracting systems, such a solvent extraction system or a leaching system, on the other hand. Such extracting systems may be operated in cocurrent or countercurrent fashion. This paper includes first a brief discussion on the general nature of cocurrent and countercurrent operation as applied to froth flotation, and then presents the experimental results of flotation of a specular hematite ore by each method, using a tall oil fatty acid as collector. Cocurrent Flotation A conventional flotation circuit involving roughing, scavenging, and cleaning flotation is illustrated schematically in Figure 1. In such a circuit the col¬lector, or extractant, and new feed ore enter together at the head of the rougher circuit, and flow cocurrently to the scavenger circuit where more collector is added. According to this practice, sufficient collector is added to the head of the rougher (and scavenger) so that the final tailings are of low enough grade to be discarded. Since the flow of collector and ore is cocurrent, the process consists of single stage contact between the extracting phase and the ore pulp. If the scavenger concentrate is recycled to the head of rougher, the overall circuit has some of the characteristics of countercurrent flow. In such a case part of the extractant (collector) is added at the discharge end of the circuit, and may

Jan 1, 1971