Search Documents

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By Dennis P. Bryan

Nevada is especially well endowed with industrial minerals, both in the number of ore deposits and the diversity of commodities. More than 600 significant industrial mineral deposits, containing 22 principal commodities, are present, in the State. The materials produced in Nevada in 1978 had a value of approximately 113 million dollars, and additional processing of some of them (e.g. gypsum into wallboard, limestone and clay into cement) added considerable more value. Table 1 shows the value of Nevada's industrial mineral production in 1978. Nevada currently supplies 85 percent of the country's barite producing 1.6 million tonnes (1.8 million short tons) valued at 30 million dollars in 1978. Nevada is second in diatomite production and contributes one-third of total lithium produced. Other industrial minerals being produced include clays, fluorspar, gypsum, lightweight aggregates, limestone and dolomite, magnesite and brucite, perlite, salt, sand and gravel, and silica. In general, Nevada produces high-value industrial minerals which are not consumed within the State, but rather, are shipped out of State. In contrast, most more populous states produce larger tonnages of lower value industrial minerals which are consumed chiefly within that state.

Jan 1, 1980

By K. Feledi

"A booster fan is an underground mechanical ventilation equipment installed in series with a main surface fan that is used to boost the air pressure provided by the surface main fan passing through it. As mining continues to expand and go deeper, the need for improved and efficient ventilation increases. This has led to the use of booster fans and other auxiliary ventilation devices in underground mines. This paper details experiments and results carried out at Missouri S&T Experimental Mine that investigated air leakage and recirculation caused by the use of booster fans. The results were compared with the situations where booster fans are used and not used.The variables considered were the booster fan blade angle and the fan combinations. Air quantity measurements were taken at each individual stopping under a number of scenarios and across four blade angle settings. The first set of situations examined were; the main surface Joy fan only running, the main Joy, and the west booster fan running, and the main Joy fan and east booster fan running. Observations were made which lead to the conclusion from the experimental analysis that booster fans affect the behavior of leakage and recirculation. The locations of the booster fan and the blade angle setting have the most effect on leakage and recirculation. To limit the potential for system leakage and recirculation, the location and size of a booster fan in a ventilation system should be thoroughly evaluated.INTRODUCTION Missouri S&T Experimental Mine ventilation system The Missouri S&T Experimental Mine has two shafts. One currently serves as the main intake shaft. Air is forced through the main shaft by a Joy Manufacturing Vane Axial fan and follows the direction shown on the map on Figure 1. The air is currently naturally exhausted through the Wheeler portal. As indicated on the map there are eight stoppings in the mine, with stoppings number 2 and 8 fitted with man doors. The mine also consists of three raises which are either fully or partially blocked, two portals with one acting as an exhaust and the other generally closed by a hydraulic Kennedy door."

Jan 1, 2015

By S. D. Thompson

Since 1965 several researchers have independently developed computer models for designing gathering belt and surge bin capacities in underground coal mine belt systems. Table 1 summarizes the models applicable to U.S. mining systems. Most of the models, employ the Monte Carlo simulation technique. Basically, the belt loading at each loading point is randomly produced from probability distributions. In some cases, a combination of deterministic calculations and probability distributions are used to simulate the loading. Once the loading is simulated, it is systematically moved through the belt system in a deterministic fashion based on belt speeds, belt lengths, and storage bin discharge rates. The coal flowing from each loading point is tracked as it moves through the belt system. When the loading from tm different sources combines on a belt or in a surge bin, checks are made to determine if capacities have been exceeded. If capacities have been exceeded the amount of spillage is calculated. At the end of the simulated time period, the cumulative spill- age is used to evaluate the belt and surge bin capacities. Naturally, a considerable amount of spillage indicates the capacities are unacceptable. Acceptable capacities are generally indicated by minimal spillage. Numerous trial simulations are often necessary to find the acceptable capacities.

Jan 1, 1987

By P. C. Clark

This paper is an overview of the requirements and concerns for minerals and pigments used in papermaking. The first part of this paper deals with mineral or pigment filling in the actual papermaking process. The second part deals with the pigment or mineral properties that are important in today's coating processes.

Jan 1, 1993

By James P. Connell

HISTORICAL BACKGROUND The American Concrete Institute defines shotcrete as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity onto a surface." This definition thus includes what is traditionally known as gunite, which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this chapter. In 1914, following the invention of the mortar gun in 1907, then chief engineer of the US Bureau of Mines (USBM) George Rice developed the gunite process for underground test work at the USBM facility at Bruceton, PA. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto tunnel in California. The greatest development was in Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Initially, shotcrete was used to reduce manpower requirements for forming and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately after the opening had been made. The incorporation of wire mesh into the shotcrete led to the new Austrian tunnel method or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the US reliance on wood or steel supports in main-line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to accept the new and seemingly unrealistic lighter shotcrete support. APPLICATION REQUIREMENTS Shotcrete is a relatively new material for use in underground support systems. Consequently, experienced miners are not always available who are capable of applying the material effectively. Shotcrete, particularly in the small cross sections typical of mine shafts or haulageways, is applied in cramped quarters under less than ideal conditions. Adequate lighting should be made available. The surface should be clean and free of running or dripping water. It may be necessary to collect flowing water in plastic pipes or water collection devices. Any dry cement dust from previous shotcrete applications should be washed from the surface in order to assure a good bond. The US Bureau of Reclamation (USBR) while shooting test panels at the Cunningham tunnel in 1974, found that experienced shotcrete operators were able to obtain up to three times greater compressive strengths than were obtained by unskilled operators using the same equipment and shotcrete mix. ENVIRONMENTAL AND SAFETY REQUIREMENTS Since sodium and potassium hydroxide, as well as other moderately toxic compounds, are often contained in shotcrete (particularly where accelerators are used), safety precautions must be taken to prevent skin and respiratory irritation. Nozzlemen and helpers are required to wear gloves, protective clothing, and ventilation hoods with a filtered air supply. Respirators approved by USBM, equipped with chemical filters that will not pass the caustic mists, may be permitted in lieu of hoods if goggles or safety glasses are worn. Protective ointments are available to reduce skin irritation. All air and shotcrete feed hoses should be equipped with safety-type couplings and secured with safety chains at each coupling to prevent whipping in the event of a hose or coupling failure. Some environmental effects can take place down-stream from the development face being supported. The accelerator compounds, as well as the portland cement used in the shotcrete, will be found in the rebound material which falls to the invert of the heading. Since these compounds may be leached from the rebound material and carried by the drainage system, it may be necessary to install neutralizing or other water treatment facilities. Investigations may find that the final reaction with other compounds being leached from the mining operations may result in a more or less environmentally acceptable end product. USES OF SHOTCRETE General Uses Shotcrete, as a combination of cement, aggregate, and accelerator, is utilized for underground openings such as shafts, adits, haulageways, and service chambers for the following general purposes : (1) primary sup¬port; (2) final lining; (3) protective covering for excavated surfaces that are altered when exposed to air (the protective covering may be of a temporary or final nature); (4) protective covering for steel or wooden supports, rockbolts and rockbolt plates, heads, nuts, and other mats, including wire fabric, used to prevent rock-falls; and (5) as a lagging material in place of timber, steel, or concrete between steel or wooden supports. These applications can be grouped into three general use categories: shotcrete used as a rock sealant, shotcrete used as a safety measure, and shotcrete used as a structural support. Use as a Rock Sealant Thin applications of shotcrete can reduce or prevent slaking of shales or other rocks that are altered when exposed to the wetting and drying cycles created by mine ventilation circuits. While shotcrete may be effective in preventing such rock alteration, at the present time it is not as economical or efficient as other commercial sealants. However, if the sealant property can be incorporated into the structural support capability, the added contribution is usually helpful. Thin applications are not usually sufficient if the alteration of the

Jan 1, 1982

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology. The failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. The mineral industry's future depends on effective innovation. So it is essential that the causes of failure are understood. Innovation can be examined equally well in the context of geophysics, geology or mining. However the author's experience has been in mineral processing and chemical engineering. So the following discussion is limited to processes and/or plants for producing mineral concentrates, metals or inorganic chemicals. More of what follows has to do with underachievement or failure than success. But this article demonstrates that there is a strong element of predictability in the former. Furthermore, it is a credit to the minerals industry and to the engineering profession that a very high percentage of projects succeed in achieving design capacity and forecast operating costs. Innovation means the introduction of something new. In this article, the words "innovative technology" are used broadly. They include new processes and novel combinations of established unit operations, as well as novel types of processing equipment or largest-ever equipment models. The discussion of project outcomes is based on personal experience or on published information. Citations are given for technical publications that provide either project information or insights into the methodology used to analyze project performance. However, specific projects have not been identified due to the rather negative connotations of some of the conclusions drawn about the less favorable outcomes.

Jan 1, 1998

By M. C. Mound, L. Fradette, C. Colbert

Metallurgical Accounting in the mineral processing industry transforms accumulated process data, including flow rates and assays, into a coherent information format. This is used to rapidly provide production reporting and key performance indications. A fully comprehensive and coherency of available data must be a component of any system expected to accomplish reconciliation in the mass balancing process. Quality issues are thus improved with such desired methods via a mass-balancing engine utilizing the results of measurements acquired by various on-line sensors, analyzers, and sophisticated laboratory equipment. Metallurgical Accounting, when accomplished through such an engine, provides high value information in a simple, straightforward, and simplified manner. Exceptional utility is then transparently available to authorized personnel for access to metallurgical accounting reports, production reports, mass balance results, performance indicators, and so on. This paper discusses how such information can be used to "drilldown" into each result set by consulting the data hierarchy to evaluate and validate calculations and input data used to produce the specific results being queried. The power of such a system resides in the full and true integration of all production and laboratory data. What is integrated are the data thus acquired via a single user interface, a single database, a single configuration tool, etc. From this comes the derivation of contextual information and its maintenance. It is possible to reduce metallurgical accounting and production reporting from possibly hours or even days to a matter of minutes. The result is maximization of information reliability and availability from masses of otherwise discrete and difficult to access key data.

Jan 1, 2003

By C. A. Pickles, D. Mallette

Silicon nitride (Si3N4 ) is an advanced structural ceramic materia1 which is presently being considered for a number of potential engineering applications, particularly in heat engines, gas turbines, and electronics. With respect to other structural ceramics, silicon nitride has relatively low thermal conductivity and thermal expansion coefficients and a moderate elastic modulus. Thus, during thermal cycling the stresses developed in this material are lower than in other structural ceramics. At the present time silicon nitride is produced via three main processes: thermal decomposition of silicon imide or amide, treatment of silicon tetrachloride or silane vapour with ammonia and nitriding of silicon powder. These three methods of production are discussed with particular attention to the effect of morphology and phase content on the properties of the final product. In this work carbothermal production of silicon nitride has been studied in a high temperature resistance furnace. Compacted briquettes of silica and carbon were produced which were reacted in a nitrogen atmosphere. The optimum reaction temperature and the carbon to silica ratio were found to be 1425OC and ten to one, respectively. The presence of large amounts of ash in the reductant promoted the formation of silicon nitride. The specific surface area of the briquettes did not have a large effect over the range studied in the present work. Briquette seeding with small amounts of Si3N4 was effective in increasing the reaction rates.

Jan 1, 1990

By Larry Powell

Rend Lake is an Army Corps of Engineers reservoir located in Franklin and Jefferson Counties in south-central Illinois. The lake consists of 20,000 acres of water and 19,000 acres of public access land. The site attracts over two million visitors a year and is surrounded by campgrounds and other recreational facilities. The lake overlies the largest tonnage of low sulfur coal in the state. Coal is being removed beneath the lake from five mines operated by three coal companies. Currently high extraction mining operations are approaching low-lying, environmentally sensitive, and high-use recreational areas. Advanced planning to maximize coal extraction and minimize potential effects of subsidence requires the development of procedures to assess the impact of high-extraction mining on the land use of the area. The Bureau of Mines, the Corps of Engineers, and the coal companies have initiated research to assess the following proposed planning steps to ensure the maximum recovery of the coal resources while minimizing impacts to surface land use: 1) Establish a dialogue between the surface and mineral owners; 2) develop a geographic information system to aid in assessing existing land use and potential changes; 3) assess the potential effects of subsidence on drainage, wildlife habitats, and changes in land use prior to mining; 4) coordinate the mining displacements with surface activities to minimize disruption; and 5) develop appropriate mitigation plans before mining occurs.

Jan 1, 1986

By J. C. Irvine

Meramec Mining Company, a joint venture by Bethlehem Steel Corporation and St. Joe Minerals Corporation, is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge Mine located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during an exploration program to discover new lead orebodies. An airborne magnetometer survey which was run by the U. S. Geological Survey, the Missouri Geological Survey, and several min¬ing companies was published in 1950 and showed an anomaly in the Pea Ridge area. Test holes drilled in 1953 and 1954 revealed the presence of a large orebody of probable commercial significance; additional drilling in 1956 and 1957 provided confirmation of this. Meramec Mining Company was incorporated in 1957 and shaft sinking began in the latter part of that year. The Pea Ridge orebody lies under about 1300 feet of sediments. It is tabular, about 2600 feet long and up to 600 feet thick, and lies in an approximate east-west delineation. The orebody dips about 800S and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite, The Pre-cambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 feet 1 inch in diameter and 2500 feet deep. No. 1 shaft, equipped with an "A" type head-

Jan 1, 1972

By Kira Mizell, James R. Hein, Tracy Conrad

"The Ninetyeast Ridge (NER) extends roughly N-S as a topographic feature for 5000 km, from 31° south to 10° north (Fig. 1) where it becomes buried beneath the Bengal Fan at its northern end. These two geographic characteristics make the NER an ideal natural laboratory for determining the influence of latitude and terrestrial input to ferromanganese (Fe-Mn) crust formation and composition. In addition to study of geographic controls on crust composition, the NER is the largest feature in the Indian Ocean that may host crusts of economic interest.Crusts were collected from 9 of 33 dredge sites from 1.4° north to 26° south latitudes during the 2007 R.V. Roger Revelle Knox06 cruise. Nineteen samples were analyzed for 69 elements each. Nine bulk crusts and 10 layers from four crusts were analyzed. Three of the crusts sub-sampled for layers did not have the bulk crust analyzed and the weighted means for those layers were calculated to obtain bulk compositions. One sample was left out of the statistical analyses because it is phosphatized and chemically quite different from the other samples (Table 1).In order to determine changes in composition with latitude, Pearson product-moment correlation coefficients were calculated for the chemical dataset and latitude of dredge sites, as well as water depth. At the 95-99% confidence level, the following elements increase in crusts moving north along the NER: Mg, Ti, S, Cd, Ni, Tl, Mn, Ba, Co, Cu, In, Li, and Zn; and the following elements decrease northward: Fe, Fe/Mn, P, As, Sc, the rare earth elements plus yttrium (REY), Bi, Ge, and Pb. These correlations indicate that the iron oxyhydroxide component and its associated elements are more prevalent to the south, and the manganese-oxide phase and associated elements increase toward the north end of the NER. This change occurs between dredges D20 and D14 (Fig. 1), with crusts from D20 and south having Fe/Mn !1.0 and those north of D20 ""1.2, with the exception of the phosphatized crust. Crust composition also changes with water depth: Th, Ge, Pb, and the middle rare earth elements (REEs) increase with increasing water depth. Thorium commonly increases in deeper water crusts, which explains the higher Th concentrations in Atlantic and Indian ocean crusts in general compared with Pacific crusts (Fig. 2 and Hein et al., 2012), including the samples analyzed here with a mean water depth of 3584 m. However, water depth does not explain the latitudinal changes because the mean water depths of samples along the northern and southern segments of the NER are roughly comparable. Surprisingly, Si and Al, representing the aluminosilicate/detrital phase, do not correlate with latitude; that is as the ridge approaches and is buried by the Bengal Fan the Si and Al contents do not increase. However, overall, Si and Al have higher concentrations in NER crusts than in central Pacific crusts. Ba can be used as a proxy for primary productivity and statistically does increase to the north along the ridge in the direction of the equatorial zone of high biological productivity. Correlations of Mg, Li, and Zn with latitude may also reflect increased primary productivity at lower latitudes."

Sep 1, 2014

By C. R. Tinsley

Investment activity in the Pacific Rim of Fire has seen a phenomenal surge from epithermal gold exploration. Individual countries are attractive because of lower up-front minerals lease costs (US, Canada), better geological prospectivity (Chile, Indonesia), or cheaper equities (Australia). Since the October 1987 stock-market crash, large companies are shedding minority joint venture interests to focus on core businesses. Some vertical integration is evident in Japanese coal investments in the Pacific Rim. This paper does not cover the aluminum industry oligopoly which is multi-national in character nor does it cover the many Canada to US minerals investments. It will be interesting to see if the new US-Canadian free-trade treaty will reverse that investment flow.

Jan 1, 1990

By B. N. Conley, K. D. Luxbacher

"The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. The explosions that occurred at the Sago Mine in 2006, the Darby Mine in 2006, and the Upper Big Branch Mine in 2010 have caused a ripple in an otherwise steadily improving safety record. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reached a level of diminishing returns. Risk management, a safety approach that has been successfully applied in various industries including mining across the world, may provide a means to surpass the safety plateau in the U.S. RISKGATE is an Australian risk management program for mines that shows great potential for application in the U.S. However, fundamental differences between the coal mining industries in Australia and in the U.S. prevent direct implementation. This paper discusses aspects of the RISKGATE body of knowledge that require some adaptation before this program may be applied to the U.S. mining industry. INTRODUCTION The underground coal mining industry in the United States has recently seen the occurrences of several high profile, multi-fatality events. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with a minimal decline of both fatal and non-fatal injuries over the past decade may signify that current safety practices have reach a level of diminishing returns. In order to combat this stagnation in performance, a modification to the manner in which the mining industry approaches worker safety may be warranted. The implementation of a risk management based approach presents a potential method for not only surmounting the current safety plateau but also for achieving the long desired objective of zero harm. RISKGATE a risk management body of knowledge designed for the Australian mining industry that shows great potential for application in the U.S. This paper discusses aspects of the RISKGATE body of knowledge that require adaptation before implementation in the U.S. mining industry. These adaptations are based on differences in operating practices and governmental regulations. This discussion will focus on the three major U.S. risk areas of explosion prevention, ground control, and moving equipment."

Jan 1, 2015

By Bruce Hebblewhite

This paper focuses on the recent achievements and practices developed through the Minerals Tertiary Education Council (MTEC) initiative of the Minerals Council of Australia (MCA), in conjunction with the three partner universities involved in mining engineering education – University of New South Wales (UNSW), West Australian School of Mines, Curtin University (WASM), and University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and development of a number of flexible, distance-based delivery programs. The paper will then move on to future initiatives. Importantly, the exciting challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering – Mining Education Australia (MEA). This will provide a common 3rd and 4th year program to all three universities from 2007, involving innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process. Such an initiative is not without its challenges, and has a long way to go, before becoming a reality. However, it offers greater attractiveness and marketing potential to prospective students, as well as economic efficiencies, whilst delivering a better quality, and hopefully greater quantity of graduates to industry. It can also form a launching platform for a much greater level of international collaboration, through a proposed International Mining Education Network (IMEN) which is currently being floated amongst a number of international educators.

Jan 1, 2005

By G. T. Adel

The application of automatic control to mineral processing operations has been gaining momentum during recent years. Many strategies are being developed for controlling crushing, grinding and flotation circuits, however, their implementation in industrial plants is being slowed down because of the costs and difficulties in evaluating these strategies in a systematic manner. An interactive computer simulation package, developed at the University of California, provides the capability of analyzing the process dynamics of mineral processing circuits. This paper presents an overview of the simulator and its application to the case studies of grinding and flotation.

Jan 1, 1983

By J. Leinart

As is readily apparent, the reliability of the early-stage costs estimated for any mining project are critical to the viability of that project. An estimate too high might leave a potentially profitable deposit undeveloped or worse yet, available to a competitor. One too low might waste investment dollars in a project not yet economically ripe. There are two aspects critical to any estimate: 1. The cost data used to represent the values of the wages, salaries, supplies, and equipment. 2. The design used to determine the engineering parameters upon which the above estimated values are based. Given that all of the information contained in Mining Cost Service is provided by suppliers, equipment manufacturers and mine operators, one wonders why there is any question as to the reliability of cost estimates developed using this information. Given that it is all actual (as opposed to statistically derived) data, where do the problems with estimate reliability lie and what is the impact of the data on that reliability? The following presents a series of analyses designed to assess the reliability of the cost estimating process. Both the actual cost data and the engineering parameters upon which they are based are examined in an attempt to quantify and understand the importance of each. While several sources of cost information are available (Means, Richardson, Primedia?s Equipment Watch, and individual suppliers and manufacturers), the following rely solely on data contained in InfoMine USA, Inc?s, Mining Cost Service and in its Sherpa Mine Cost Estimating Software.

Feb 27, 2013

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960's. During 1967 the Bureau of Mines assisted the Climax Uranium Co., Grand Junction, Colorado in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (1). Atlas Minerals, Moab, Utah has used hydrogen peroxide to control vanadium and sodium levels in their uranium concentrates since 1969 (2). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product.

Jan 1, 1980

By Y. A. Attia, M. Elzeky

Thiobacillus ferrooxidans bacteria were used in this work to study the effect of bacterial adaptation on the bioleaching of three iron-bearing sulfide minerals, namely, pyrite, chalcopyrite and arsenopyrite. The change in the pH during the bioleaching process was observed and the mechanism of the bacterial action were discussed. It was found that bacterial adaptation prior to bioleaching, enhanced the degree of sulfide leaching by 2-4 folds over that of non-adapted bacteria. A1 so the bacterial activity was enhanced by 2-4.8 folds. The pH of leaching solutions was decreased by the increase in both adaptation period and bioleaching time. It was also concluded that the mechanisms of bioleaching of iron-bearing sulfide minerals involved both the direct and indirect bacterial action simultaneously.

Jan 1, 1989

By Ivan V. Klumpar

If components of a gas-liquid stream react with each other and with stationary solids, involving parallel and sequential, reversible and irreversible, and slow and instantaneous reactions, the process can be defined by a set of simultaneous differential rate equations and simulated as multistage semibatch re¬actors. Each stage is divided into finite time increments. Within each increment, even the simultaneous reactions are treated as sequential. The proposed method follows process evolution from non-steady state startup to normal operating conditions. It allows computing byproduct buildup in recycles, tracer response curves and, in case of underground processes, expansion to adjacent parts of the deposit.

Jan 1, 1979