Search Documents

By William M. PhD. Schafer

The net acid generation (NAG) pH method is an important analytical tool that supplements static and kinetic tests for assessment of the acid generation risk of rock samples. This method is useful because it is simple, rapid and cost-effective; it combines features of the static and kinetic tests; and it can be conducted at mine assay labs. The NAG pH test is particularly effective for operational testing programs used to classify, selectively handle, and route potentially acid-generating waste rock. The NAG pH procedure is based on a 24 hour oxidation of a pulverized rock sample with hydrogen peroxide and subsequent measurement of the sample's pH. If the NAG pH is below a critical value, determined empirically, then the sample has the potential to generate acid in the field. The critical NAG pH value is typically within the range of 3 to 4.5, but the exact relationship between NAG pH and potential acid generation should be determined individually for each mine site, based on comparison with results of acid base accounting, humidity cell tests, and mineralogical analyses. Calibration and use of the NAG test for predicting ARD risk at several mines are described in this paper.

Jan 1, 2000

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995

By B. G. McNish

Neutron Activator Laboratory Analyzer used for Rapid Analysis for Ore Blending, Stripping, and Mine Control BAUXITE is a rock and not a mineral. Since it is a rock, its mineral content varies depending upon the parent material, the topographic location of the deposit and the severity of the weathering and oxidation processes which produced it. At Bauxite, Arkansas the major mineralogical constituent of the bauxite is gibbsite with ~IL- purities of silica, iron oxide, and titania minerals. Minor amounts of other minerals are found. Chemical composition varies from 45% to 60% alumina, 5% to 25% silica, 1% to 15% ferric oxide, and 1% to 3% titania. The Arkansas bauxite region is located entirely within the north- central area of the West Gulf Coastal Plain near the northwestern boundary with the Interior Highlands. The region trends northeast-southwest and is about 42 kilometers long. It is divided into two districts; one in Saline County and the other in Pulaski County. The Saline District is the most important since it has produced most of the bauxite. This district is located at Bauxite, Arkansas and the deposits are found around the flanks of the Saline Dome. It is roughly square-shaped and is about 190 square kilometers in area. The source rock for the deposits is a Late Cretaceous, grey, nepheline syenite.

Jan 1, 1979

By C. G. Carlström

The total iron ore production in Sweden in 1969 was 33.3 million metric tons. 31.7 million tons were exported mainly to Western European countries. 27.8 million tons (87 per cent) originated from the mines at Kiruna, Svappavaara and Malmberget, located just north of the Arctic Circle in Sweden. Planned production for 1970 is 25 million tons during 10 months, due to a strike at the beginning of the year. Present production plans for the next five years expect an annual export capacity around 33 million tons in 1975, including 5.7 million tons of pellets. The mining and shipping at the loading terminals of Narvik on the Atlantic coast and Luleå at the Gulf of Bothnia are managed by LKAB - a 96 per cent state-owned company. 4 per cent of the share capital is owned by the private Grängesberg Company. The railway - 106 miles from Kiruna to Narvik and 130 miles from Malmberget to Luleå - is operated by the State Railways in Sweden and Norway. Comprehensive expansion of the Narvik ore port will be carried through during the next five years to increase the annual shipping capacity to at least 35 million tons and meet the development of rapidly growing ship sizes.

Jan 1, 1970

By H. Cetin

The availability of coal resources of selected 7.5-minute quadrangles of southwest Indiana was examined in this study. Resources were defined as original coal in place, remaining after mining, and currently available considering land-use and technological restrictions. The amount of coal mined from each study area varies depending on the mining practices of the companies operating within the area. Of the three quadrangle investigations, the available resources range from 50 percent to 79 percent of the original resources. Most of the coal resources under deep-minable category were not available because of technologic restrictions, such as insufficient coal thickness.

Jan 1, 1996

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By Long An, Chao Wu, Yuanhui Li, Xing Sun, Shuai Xu, Changyu Jin

Stage open stope mining (SOSM) maintains the stability of excavation openings by leaving a large number of rib pillars. Affected by the strong unloading due to stage mining and the low width-to-height (w/h) ratio of the pillars remaining, large-scale destabilization disasters of rib pillars or excavation openings easily occur when the distribution of ground stress or the size of rib pillars is unreasonable. In view of these problems, a physical SOSM model test was carried out based on an underground metal mine in the city of Chifeng in China, revealing the deformation and failure characteristics of the SOSM pillar group by overloading.

Jul 1, 2023

By W. M. Kidd

INTRODUCTION Uranium mine inspection in Canada forms one element of the enforcement of the Atomic Energy Control Act; it is under this Act that all Canadian uranium mines and mills are licensed to operate. Inspection duties are carried out by a small core staff of federal government inspectors (working for the Atomic Energy Control Board (AECB)) largely supplemented by provincial mine inspectors working on behalf of the AECB. Unlike most resource extraction in Canada, uranium mining is under federal jurisdiction and consequently it was the AECB who decided in 1975 that changes in the Canadian uranium mining industry, particularly its expansion and the expanding role of the mine inspector in the limiting of exposures, warranted the offering of a special radiation protection training course. The Uranium Mine Inspector Training Course (UMITC) was first conducted in 1976 at the Elliot Lake Centre in Elliot Lake, Ontario. Subscription for the course was not limited to mine inspectors to enable union stewards, management personnel and provincial/federal labour inspectors to attend. This paper will present an outline of the course content, the format of its presentation and non-curriculum aspects of running a course of this type in uranium-producing community. The core lecturers for UMITC are drawn from the Radiation Protection and Uranium Mine Divisions of the AECB. In addition, guest lecturers are invited from universities and medical research centres together with industry professionals and government researchers. In all some twenty-four plus presentations are made over the first five days of lectures. The program topic areas, hazards, controls, measurements, record-keeping and health effects are preceded by an intensive half-day session on radiation fundamentals. TOPICS Hazards [Dust] A review of the dynamics of airborne particles including the effects of particle size, gravity and wake-turbulence on the behaviour of dust clouds. Associated topics are migrational aspects of dust particles and specific dust-generating mine operations. [Radiation] Canadian uranium mines are increasingly diverse in nature ranging from large scale low-grade underground operations in Elliot Lake to smaller high-grade open pits in Saskatchewan. Papers are presented on assessments of internal and external exposure, the metabolic pathways of ingested or inhaled radiation and the specifics of mine and mill hazards. Radiation hazards are further broken down into gamma surveys of uranium mines, radon daughter concentrations and problem areas. Controls The relationship between mining methods and the operating environment is critically important to ensuring safe working conditions. This refers to both the selection of machinery/devices, etc., and to engineering controls which are instituted to remedy problems created by new technology. UMITC examines a number of possible mining techniques, their criteria for selection and impact on the working environment. Control measures, ventilation practices and design, the need for continuous water misting and special open-pit precautions are presented. These lectures frequently conclude with suggestions for better operating guidelines for mine ventilation systems and the need for greater co-operation between the ventilation department and the underground crews. Measurements Uranium mining regulations stress the need for a high standard of exposure monitoring, statistical planning and record-keeping. [Statistics] Although many course participants are well versed in statistics, certain fundamentals are repeated and include, the concepts of mean, variance, standard deviation and standard deviation of the mean. Confidence levels, decision-making based on sample statistics and statistical records are also discussed. [Dust Measurement] Dust measurement is particularly critical in the mines where the high silica content of the ore body, such as those at Elliot Lake, results in the continuous generation of dust. Sampling practices, filtration, impaction, thermal impaction and electrostatic precipitation are explained together with the methods of counting samples to determine free silica. Konimetric and gravimetric techniques for dust sampling are compared and contrasted. [Radiation Measurements] Both collective and personal dosimetry systems are used in the Canadian uranium mining industry and lectures are presented on each. Techniques and possible sources of error are discussed for a variety of radon and radon daughter measurement methods - Lucas method, Tsivoglou and modified Tsivoglou, Kusnetz, Rolle. Instant working level meters and personal alpha dosimeters are explained in terms of calibration, maintenance, readout and estimation of accuracy. A lecture outlining dose estimation by means of bio-assay, whole-body counting and the use of TLD's concludes the topic. Record-Keeping An overview of the problems of changing limits,

Jan 1, 1981

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By Christian F. Baiz

The author will present a discussion of the steps which must be taken by the prospective developer of a small mining operation to establish technical credibility when seeking financial backing. Particular emphasis will be given to the differing levels of technical work (and their relative cost) which must be accomplished to supply the information necessary to satisfy potential investor groups, whether they be other mining companies, equity investors, or financial institutions such as venture capital firms or commercial banks.

Jan 1, 1981

By W. G. Willson, D. E. Walsh, B. Irwin

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture reabsorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid feel.

Feb 24, 1997

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

By R. S. C. Rogers

The present study examines the use of two vs. one stage of hydrocyclones in a pilot scale ball mill circuit. The approach used for doing this is based on computer simulation with mathematical models that explicitly account for the grinding mill/classification system interaction. Parameters for the ball mill model are obtained using a short-lived radioactive tracer method in open circuit tests of the study mill. The hydrocyclone model, based on the size selectivity concept, is developed and validated in standalone testing of the study hydrocyclones. Simulation procedures are validated through actual tests of the closed circuit grinding configurations of interest. Results of the evaluation indicate that two stages of hydrocyclones in the study circuit would improve classification, increase productivity and lead to more closely sized circuit products when compared to the conventional one stage hydrocyclone circuit. A computer simulation approach for comparing these circuit configurations in larger scale grinding circuits is also suggested.

Jan 1, 1981

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By James S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1981

By Allegra Yeley, Ted Klemetti, Gamal Rashed, Tim Miller, Nicole Evanek

In 2015, the Subtropolis Mine in Petersburg, OH, experienced a massive ground collapse that continues to grow over time. Horizontal stress effects have affected the roof at this operation in the past and may have played a large role in this collapse. Horizontal stress can impact the roof and floor stability and endanger the health and safety of underground stone miners. Mines experiencing damaging effects from horizontal stress typically find that the principal stress direction is the same throughout the mine and the region. At the Subtropolis Mine the principal horizontal stress direction appears to change as conditions change and differs from the regional horizontal stress, particularly near the collapse or other roof fall areas. The growth over time of this collapse and other roof falls have been captured and analyzed using geologic mapping, 3D LiDAR scanning, numerical modeling and geographic information systems like ArcGIS. Utilizing these tools to better understand sitespecific conditions can be critical to reducing the potential of massive ground collapses in the underground limestone industry.

Feb 1, 2024

By W. L. Chen

In the United States hydraulic cyclones have been used for thickening, classification and cleaning in coal preparation plants for many years. The cleaning cyclones presently in use are based on using a "heavy medium", such as a fine magnetite and water pulp. The latest addition to cleaning cyclones is the one which uses ?water only?, or simply called "Hydrocyclone". Just as was the heavy medium cyclone, the hydrocyclones were originated in the Netherlands (1, 2). Plants using hydrocyclones were built in Europe (3) and test plants were erected in Canada (4, 5, 6) and India (7). Roberts and Schaefer Company has built four plants using hydrocyclone circuits. One additional plant is in the process of construction.

Jan 1, 1965