Search Documents

By Earl Cook

A high-energy economy based on fossil fuels is in fundamental conflict with an ideal of clean air, clean water, undisturbed scenery, and maintenance of fragile ecosystems. There is an inevitable trade-off between the material standard of living of a modern society and the conservation of its environment. During the past four years, some of the costs of environmental protection have been internalized in the energy-flow system of the United States. The cost of bituminous coal and fuel oil usable under new air-quality standards has doubled or more. The cost of mining coal underground has risen because of a 20-30 percent reduction in productivity resulting from new environmental health and safety legislation; the economic impact of proposed surface-mine regulation may be equally severe. The cost of producing electric power has been rising at a 12 percent annual rate because of environmental costs, and would be climbing still more steeply were it not for the continued forced subsidy of natural-gas consumers by natural-gas producers. The efficiency of the automobile, already a monument to the triumph of self- indulgence over economy, is being further decreased by addition of anti-pollution devices. Part of the recent sharp rise in agricultural costs stems from the fact that five energy units of fossil fuel go into U.S. agriculture for every energy unit of raw food that leaves the farm; further large injections of fossil-fuel energy occur in the transport, processing, and refrigeration of farm products.

Jan 1, 1974

By Paul H. Johnson

A field investigation was undertaken to study some of the. chemical and hydrological aspects of leaching an impermeable copper sulfide waste dump. Samples, obtained by means of a Becker pneumatic drill from Kennecott's Chino "J" dump, near Silver City, New Mexico, were analyzed for their moisture and soluble-salt content, Fe +2 , Fe +3, Cu +2 , and H in their interstitial solutions and non-water - soluble Fe, Cu, and S in their rinsed residues. Conclusions were drawn from these data concerning the overall chemistry of impermeable-dump leaching and the hydrological characteristics of the dump.

Jan 1, 1970

By G. Goellner

The thick alluvial sand and gravel deposits along the base of the San Gabriel mountain range in Southern California area have been mined for construction aggregates for over 100 years. Encroachment of high-density urban populations in this area has led to concentrated mining in a handful of open pit mines with single production faces reaching up to 55 m (175 ft) in height, and long transportation distances from the pit to the processing plant. Aggregate producers have responded to these challenges by developing innovative mining systems which enable low-cost, full-face mining of the alluvial material, and low cost delivery of this material to the plant.

Jan 1, 2004

By Su Yang, Pang Shun, Xiaoding Xu, Guodong Yang, Hengfeng Liu, Meng Wu, Yuejin Zhou

By introducing the hydrochemical damage variable of coal gangue granular material, this paper analyzed the evolution law of gangue mechanical parameters with hydrochemical damage. By constructing a gangue damage model considering multifield coupling, the damage mechanism of gangue under multi-field coupling was revealed from the microscopical aspect, and the influence law of gangue damage mechanism on the dissolution of toxic substances under multi-field coupling was obtained: the conditions of Test 1 have the greatest influence on the porosity of coal gangue, and the damage of coal gangue is the greatest. Cu, Zn, Cd, and Pb are more easily leached under acidic conditions. The coupling effect of seepage, temperature, and chemical field can promote the formation of secondary voids, change the voids, and form migration paths in coal gangue. The kinetic model of toxic leaching of coal gangue under multi-field coupling can be well characterized by Elovich equation. The release mechanism of heavy metals is mainly manifested as delayed diffusion or dissolution in the early stage, diffusion and dissolution in the middle stage, and depletion in the late stage.

Nov 23, 2023

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By James A. Hartlage

Work on the design of Kelex 100 was initiated several years ago at the Research Laboratories of Ashland Chemical Company. The effort was specifically directed toward the synthesis of an organic molecule which would strongly and selectively chelate copper ions in acidic solutions and form an oil soluble complex which would be stable in contact with an aqueous phase having a pH of approximately one. This publication describes efforts to establish data which could be used to estimate the economic utility of the new reagent. For helping to accomplish these ends, the author wishes to acknowledge the assistance of Mr. A. V. Henrickson of Hazen Research, Inc. for gathering a portion of the data presented here and to thank the copper companies who supplied leach solutions for studies described in this paper.

Jan 1, 1969

By M. Radwan, S. Shimada, S. Z. El-Tawil, K. A. El-Barawy, Y. Miyamoto

This study presents the results of synthesizing monolithic siliconoxynitride, Si2N2O, ceramic from a mixture composed of reclaimed silicon and natural desert sand by using the nitriding combustion synthesis method. Single-phase Si2N2O powder was prepared by the combustion of a mixture composed of silicon and pulverized sand in 3 MPa nitrogen gas. The combustion reaction completed in 2 min and the combustion temperature reached 1577°C.The as-synthesized Si2N2O powder is agglomerate of fine particles with sizes < 5 µm and has various morphologies; rod-like and irregular crystals, irregular kinking, hollow crystals and grown pseudo-hexagonal prismatic crystals. Porous Si2N2O compacts (24.5–47.1% porosities) were fabricated from the synthesized Si2N2O powder at different calcia-alumina additives (5–20 wt%) by normal sintering at 1500°C for 1 hr in N2atmosphere.They showed superior oxidation-resistance at high temperatures up to 1500°C in an oxidizing atmosphere of Ar/O2/H2O(70/20/10 kPa).Near-full dense Si2N2O compacts were also successfully fabricated from the synthesized Si2N2O powder with 5 wt% oxide additives by using the spark plasma sintering at 1600°C.DenseSi2N2O had good mechanical properties (18.7 GPa Vickers hardness, 3.3 MPa.m1/2fracture toughness and 363 MPa strength) and excellent chemical and oxidation resistance.

Jan 1, 2004

By John Callahan

A stream sediment (minus 80-mesh and minus 60-mesh panned concentrates) and lithogeochdcal survey for gold did not locate any Triassic-age placer deposits in the northern Wadesboro and southern Sanford basins in North Carolina. A stream sediment geochemical program for uranium funded by the North Carolina Energy Institute did identify one and anomalous site (8.5 ppm U; 5 ppm Th) near Covenington, North Carolina and eighteen possibly anomalous sites (1-1.6 ppm U) . Five of the eighteen samples with uranium levels in the 1-1.6 ppm range have high thorium levels (112-853 ppm) and may indicate a monazite source for the uranium. Gold values as high as .83 ppm in the stream sediments and 9.3 ppm in the panned concentrates were obtained during the survey. Small (<.5mm) flattened grains of gold (1-4 grains) were observed along with coarse kyanite and/or monazite in some of the panned concentrates. A distinctive pattern of high gold values in the sediments was observed in the vicinity of Mangum, N. C. where Minard (13) reported values as high as 2.1 ppm £ram a Triassic lithology. Follow-up gold analyses on over 400 rock samples from twenty-eight exposures near Mangum failed to obtain any high values (<55 ppb). The presence of coarse kyanite, monazite and gold in panned concentrates may be from a source younger than the Triassic lithologies that the streams currently drain or adjacent Paleozoic rocks.

Jan 1, 1979

By N. Arbiter

If two fluid phases are brought into contact with a solid, one fluid may completely wet the surface to the exclusion of the other, or both may wet it, forming a three-phase line of contact. These relative wetting tendencies are quantified by the contact angle 0 which is related by Young&apos;s equation (1,2) [12 cos? = 13 ? 23] [to the three interfacial tensions (3). No contact angle for the first fluid, indicating that it does not wet the solid in the presence of the second, means that the difference between the two solid-fluid fluid surface tensions, - 8 is greater than (or just 13 -23 equal to) the fluid-fluid tension 12; a finite angle indicates that the difference is less.*]

Jan 1, 1964

By William N. Poundstone

Since World War II, when off-track mining became popular, mining machinery has undergone much change. However, the change has been basically to make the machines more powerful, more productive and more reliable. Little change has been made, in this period, in the basic mining system. While steady improvement was made in productivity until the passage of the new Federal Coal Mine Health & Safety Act, I believe that the cost Co benefit ratio of further improvement from this basic approach of improving the existing extractive tool is not as promising as I believe may be obtained from a new approach. Consequently, six years ago Conoco and Consol undertook a comprehensive long-range R&D program to see if improvements of a more basic nature could be made in underground mining. We concluded early in our program that while many things currently limit the rate of production such as the rate at which roof can be supported, time needed to advance ventilation systems, time required to clean up and rock dust, time required to maintain and service equipment as well as time lost due to haulage deficiencies, that the key to improvement was a truly flexible continuous high capacity haulage. With face equipment in use today, mining rates can be increased with such a haulage system where the ability to support the roof exceeds the ability of conventional haulage equipment to remove the coal. More importantly, if we could develop such a system, it would set the stage for development of far more sophisticated methods of mining at the face than exist today, and as new and more dependable mining machines and methods are developed, continuous transportation will enable the gains envisaged in production to be realized.

Jan 1, 1974

By Stanley C. Suboleski

1977 was the modern day low point for productivity in the coal industry. At that time, no one could have predicted that the industry was about to enter a productivity rise that would continue unabated through the 1980s. Thirteen years later, the cause of this phenomenon is still not well understood. While many government studies focused on the fall in productivity from 1969 to 1977, none have been undertaken to explain the rise. Some of the likely causes of the gain in productivity during this period will be discussed here. An attempt will also be made to quantify the value of some of the technical innovations that have taken place. The remainder of the gain is assumed to come from non-technical sources. The nature of these sources, although largely non-quantifiable, is also discussed. Since the number of mines that have adopted the technical innovations noted here is largely unknown, the actual contribu¬tion of technological changes to the overall productivity gain can only be estimated.

Jan 1, 1990

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By Roland Hoet

Mine operators, conveyor system designers, consultants, and manufacturers have had opportunities over the past decade to utilize various actively controlled technologies to drive complex underground conveyor systems. These technologies included several electrical drive solutions, mechanical drive solutions, and hydromechanical (fluid coupling) drive solutions. All of these technologies have their inherent advantages and disadvantages, and only after several years of operation can mine operators fairly evaluate the overall benefits (short term performance and cost vs. longer term operational and maintenance costs) of any particular drive. Far too often in today&apos;s world, decisions for new equipment are made with inadequate regard to issues concerning serviceability and maintainability. Many of the newer electrical technologies (primarily AC variable speed drives) which have been used in recent years were selected based on the perceived desirable benefit from variable speed operation. This technology, however, which differs sign8cantly between various manufacturers, is in a constant state of evolution which puts into question the manufacturers&apos; ability for long-term product support. In addition, various forms of this technology have also generated some undesirable operational issues, including reduced motor life, harmonics for the power system, and mine communications problems. This technology is also extremely current-limited, which results in problems handling overload conditions, a frequent occurrence often resulting from a decline in the coal recovery rate (conveying more rock than coal). The fluid coupling, however, is based on a technology which has been used successfully in underground conveyor applications for decades. Although the base hydrodynamic technology is well proven and has inherently beneficial characteristics on conveyor applications, Voith has continuously improved on this technology to meet the increasing demands of today&apos;s challenging conveyor haulage systems. Recognizing a need in the market for a reliable, actively controlled drive system, Voith Turbo began development in 1996 of a new, actively controlled coupling which was targeted specifically for the higher powered, complex underground conveyors. Voith introduced the new TPKL Fill Controlled coupling product to the market in 1997, and the first two applications for this new technology were on multiple drive mpper booster applications on longwall panel conveyors. Since the successful startup of these two conveyor systems in 1998, Voith has supplied over 200 TPKL couplings to the mining industry worldwide, with over 150 in US coal mining applications alone. This paper will provide an overview of the TPKL&apos;s capabilities, performance, and reliability based on the TPKL&apos;s impressive installation base and operational history.

Jan 1, 2004

By J. Kern, T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By Steve Kral

For a state whose roots are in mining, most Colorado residents probably do not realize that the industry still contributes heavily to the state’s economy. In 2005, the industry contributed, directly and indirectly, about $8 billion to the state’s economy, according to the Colorado Mining Association (CMA). It employed nearly 10,000 people at mines and support businesses. And the mining industry in Colorado is one of the highest paying occupations in the state, averaging about $80,000 a year in wages and benefits. The state’s coal mining industry produced nearly 36 Mt (40 million st) of coal in 2005, valued at $800 million, the CMA said. That was seventh in the nation. And Colorado’s only major gold mine produced 10.2 t (329,000 oz) last year, valued at $124 million. That was third in the nation. And Phelps Dodge’s Henderson Mine produced about 12.7 kt (28 million lbs) of molybdenum, valued at $350 million. Colorado is the largest molybdenum producing state in the nation.

Jan 1, 2006

By Hiroyuki Tamaru, Futoshi Kusumoto, Kosuke Tanimura, Atsuyuki Kimura

"SUMMARY The Hachinoshiri tunnel is a 2,469 m long two-lane road tunnel on the Chubu-Odan Expressway. Since more than 70% of the total tunnel length consists of low strength rock masses the competence factor of which is less than 1.0, it is expected that a self standing span cannot be achievable because of no ground arch to be established. The tunnel was thus designed with tunnel support patterns forming multi-arc early ring closure that can develop the load-carrying capacity estimated from the exerted earth pressure, Po, which can result from the competence factor, cf. The tunnel support pattern was selected based on the competence factor at tunnel face, then the subsequent tunnel support patterns were determined with reference to the monitoring data. The tunnel construction adopted full-face excavation accompanied by early ring closure using a 330 kW road header. The proposed construction methods at this tunnel site have turned out ensuring tunnelling in massive squeezing rock, so that they can be verified as reasonable tunnelling technologies, clarifying the relationship between the characteristics of the mechanical behaviour of the tunnel and its design parameters. INTRODUCTION The presence of highly weathered mudstone having the competence factor less than 1.0 where the tunnel became unstable with the early ring closure having the distance to early ring closure, Lf, of 6 meters, resulting in difficulty in maintaining the inner section of the tunnel, prompted a substantial amount of high strength double support and replacing of the tunnel support (Sato et al., 2015). Based on the mechanical characteristics learned from the construction, the mechanical stability of multi-arc tunnels was investigated using 3D FDM analyses with respect to the ratio of the radius for early ring closure, r3/r1, and the distance to early ring closure, Lf, so that tunnel support patterns for early ring closure can be established in terms of the competence factor, of, which was employed for a 725 m long section. Consequently the tunnel support patterns for early ring closure which can be determined from the competence factor became applicable to tunnel construction. The relationship between the characteristics of the mechanical behaviour of the tunnel and its mechanical parameters was also clarified. The early ring closure method adopted ensured tunnelling in massive squeezing rock, verifying its effectiveness in stabilizing the tunnel."

Jan 1, 2016

By Charles C. L. Smith

A review and comparison is made of the circuitry utilized for dc crane control systems. Anti-parallel three phase full wave thyristor bridges for dc motor reversing and speed control are compared with a single three phase full wave thyristor bridge for speed control and either contactor or static switching for reversing control to obtain complete four quadrant operation for crane material handling. In recent years the Harnischfeger Corporation has developed a solid state adjustable voltage control system to control the speed and direction of dc motors for crane applications and handling materia1.1 Shunt wound dc motors are utilized and speed is controlled in the motor base speed operating region at constant torque by a thyristor, silicon controlled rectifier (SCR), adjust- able armature voltage supply. The three phase thyristor bridge is the power controlling element of the dc adjustable voltage control. ELECTROTORQUE is the Harnischfeger Corporation registered trade name for this type of drive system. By controlling the gating signals or firing pulses to the thyristor bridge SCR&apos;s the dc output voltage can be varied over a wide range. This range is limited only by the magnitude of the ac applied voltage. To obtain operation of the motor in both directions two thristor bridges are connected in an anti-parallel arrangement. A typical schematic for two anti-parallel connected three phase SCR bridges is shown in Figure 1.

Jan 1, 1973

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By Paul D. Klipfel

Introduction Mineral exploration interest, principally for gold, in the south-western Pacific has surged to new proportions. This is primarily due to the application of epithermal exploration concepts in the Australian-Oceana region. Other factors that have contributed to the high level of exploration interest include governmental policies supportive of mineral exploration, along with relative ease of tenure access and a relatively short bureaucratic process. This paper highlights exploration and development activities in the North Island of New Zealand, Fiji, Vanuatu, the Solomon Islands, and Papua New Guinea (Fig. 1). It provides a framework to understand the overall recent enthusiasm that has been brought to the south Pacific by explorationists. Through these recent developments, it is clear that the south Pacific region will become a significant gold producing area and thereby worthy of attention and study. Papua New Guinea alone is the free world&apos;s seventh largest producer (Table 1). And, with the addition of production from deposits presently being developed, this status is likely to be raised. History Gold was first noted on various Pacific islands in the late 1500s by Spanish explorers. They thought they had reached the legendary King Solomon mines. Since then, the history of prospecting in the southwest Pacific has coincided with the colonization of the region. Settlers in New Zealand extensively mined alluvial and lode gold deposits starting in the 1850s. The spread of European colonization to the more remote Pacific islands from 1880-1940 was accompanied by varying degrees of prospecting activity by planters, traders, and settlers. Some were successful, others may have been successful, but never returned due to hostile indigenous peoples or disease. In general, records of such prospecting activity are meager and exploration leads are, in some cases, gained through local village folk memory. Most early discoveries were alluvial finds. These led to placer operations, particularly in New Zealand, the Solomon Islands, and Papua New Guinea. Continued prospecting located lode deposits such as the Morobe Gold-field of Papua New Guinea, the Coromandel Peninsula of New Zealand, and the Emperor of Fiji. Some areas were prospected thoroughly. Yet others, such as Vanuatu, remained relatively unexplored until the present exploration surge began. During World War II, interest in minerals was diverted. It was renewed significantly until the middle 1960s and early 1970s when regional porphyry copper exploration was conducted.

Jan 10, 1987

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005