Search Documents

By J. B. Gwiazda

Maintenance of a constant load setting throughout longwall support units and selection of the proper initial bearing capacity depending on the type of roof strata are the basic factors that ensure good performance of roof support in a longwall. These requirements can only be met by hydraulic support. The greatest advantage of hydraulic support is achieved when uniform pressure is imposed on the roof throughout the length of the longwall. Such support, however, is provided only if each of the support units acts with the same force against the roof, i.e., has the same setting load. In such cases, the roof behaves like a uniform plate without bending and shearing stresses, thereby ensuring an undisturbed structure. Without a positive set value system, achieving an equal setting load for all units of the longwall support is impossible. Due to alterations of the feed line pressure of support units as well as some reasons related to man's psychology, operators extend the height at different setting loads. This produces nonuniform roof stress, and disturbs the structure. Consequently, the roof usually cracks. The author has developed a positive set value system, which is described in this Technical Note. Selection of the setting load Two pressure values in the feed lines are usually applied in longwall hydraulic systems. Lightweight support is fed by 25 MPa (250 bar) liquid, while heavy duty units receive a nominal pressure of 31.5 MPa (315 bar). Such pressure is required not only for the props but also to power the adjust¬ment jacks and the advancing ram. If the feed pressure is too low, there will be difficulty in shifting the unit despite the inversion system of the advancing rams. On the other hand, for many roof types, the feed pressure often appears to be too high when applied as the setting load pressure. An excessive setting load acts too strongly against the roof, crushing weak strata close to the roof. The author has recognized a case where an excessive setting load destroyed not only the nearby roof strata but also the strata above a 2-m (6.6-ft) sandstone layer. In addition, an excessive setting load relieves the side¬walls, increasing the resistance when using cutting machines. As a result, the yield of coarse coal is diminished, and increased fines dominate in the final product, lowering its economic value. As indicated, selection of the proper setting load, depend¬ing on the mining and geological conditions of the extracted seam, is extremely important. In some mines, measures applied to prevent disturbances include reduction of the feed line pressure by adjusting the feed pump valve. The disadvantage accompanying reduced feed line pressure is more difficult operation in advancing the ram. Due to the reduced feed line pressure, the force of the advancing ram is much lower than the designed value. Other designs suggest using a third feed line. However, installation of supplementary valves on the support units is required, a time-consuming and expensive procedure. The disadvantages of the powered supports are eliminated by a system designed by the author. So far, such a method of setting load control has not been used in any type of support. Setting load control unit The designed positive valve set for prop loading and the setting load control correspond to existing control systems for hydraulic powered support. The layout of the unit connected to the hydraulic prop control is presented in Fig. 1. The unit is marked LIDS. It incorporates three valves that may operate separately or connected. Valve A automatically opens and closes with liquid flow in the prop feed circuit. The valve is opened when the canopy touches the roof and closed when the support unit is withdrawn. Valve B serves as the setting load control. Valve C automatically opens and closes the flow in the line connecting the under-piston space of E to the prop F with the separator G. The valve block of each support prop is marked BZ. The UDS unit is connected by the hydraulic lines to the F prop control circuit. A valve is connected by H to pressure line J and by K to the G separator. In the UDS-3 version, line L is connected to M, linking the over-piston space of F prop with the G separator. Valve B is linked with valve A by a connector; it is also connected to the under-piston space E of prop F by line P. Valve C is fixed between lines K and P, connecting space E of prop F with the separator G. When setting the support, the liquid flows from line J through separator G, the BZ valve, and valve C to the space E of prop F. When reaching the roof with the canopy, valve A is opened and C closes. In this way it is impossible for the operator to cause the liquid pressure in space E of prop F to reach the level of line J. The prop pressure is set by valve B of the UDS unit. When withdrawing the support, valve C is automatically opened and A closed. Three UDS units have been fabricated and are designated

Jan 1, 1990

By Gary S. Brierley, John W. Critchfield

This paper is a case history of a subsurface exploration program conducted for a system of sewer tunnels in upstate New York. The focus of the discussion is a non-technical outline of how the exploration process was organized to efficiently produce a large body of geological and geotechnical data. A brief description of the project and geological setting is provided, the scope of the exploration program is summarized, the logistics of collecting, processing and reporting subsurface data is outlined, and recommendations for management of explorations applicable to any rock tunnel are provided.

Jan 1, 1983

By Donald J. McKee

The product sizing and tonnage from a grinding circuit are the end result of a series of linked size reduction stages which always involve: fragmentation in mining; degradation in transport of ore; crushing and finally grinding. A case study is presented which illustrates the substantial effect on autogenous mill throughput of different mining practice. It is shown that it is possible to model each of the size reduction steps of fragmentation, degradation, crushing and grinding. The way in which this predictive capability is used is dependent on the operating constraints of each mine-mill combination.

Jan 1, 1998

An information system (I/S) plan is a means for establishing and communicating the direction the organization intends to take to provide the information required for achievement of organizational goals and objectives. The rapid advancements in information technology, the increasing complexity of systems, and the growing dependence of mining companies on these information systems have emphasized the need for more comprehensive I/S planning. This subsection explores this need, the role I/S planning can play within a mining company, and finally describes a methodology for development of an I/S plan.

Jan 1, 1979

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By Ted C. Mathews

Pre-concentration by sorting is as old as the mining industry. Inevitably waste rock is broken with ore. Separation may take place in the stopes by selective mucking and transport, or selective loading and transport of ore and waste by 12-cu, yd. shovels and 100-ton trucks in large open pit operations. Hand sorting of 1" to 16" pieces, formerly widely practiced at underground chutes and prior to or following first stage crushing, has greatly diminished in the United States with its high per hour labor cost, although still widely practiced in other countries and, surprisingly, in some of the most modern mills where inexpensive labor is available. The economics of pre-concentration by sorting is attractive since elimination of waste at any cost less than the total milling cost will show a profit. The size at which sorting should be under- taken is determined by the size at which liberation is secured to yield a product of ore and waste, and greatly influences cost and the point in the flowsheet where sorting can be undertaken. In some instances mining costs can be reduced where an inexpensive sorting system to eliminate waste is combined with a less selective and less costly mining method. This is particularly true in deep mines where hoisting capacity determines the rate of extraction and sorting is performed underground, with waste utilized for fill. Hand sorting, while efficient, is expensive because of low sorting rates. Peale (1) quotes man hour capacity at 1/3 ton per hour on sizes 3/4" to 3" copper ore, and up to 5 tons per hour on rich iron ore sized from 4" to 16".

Jan 1, 1974

By Michael C. Stanley

The set of discoveries for a mining district or camp is a reflection of the exploration history. In the western Abitibi greenstone belt of Ontario, future exploration can be guided by a study of statistical trends of known gold deposits. In this area simple trends indicate a strong decrease in the contained quantity of gold discovered through time. Much of this decrease is attributed not to falling mining grades but to smaller tonnages of ore. A plot of the largest discovery in each ten year time period suggests that deposit discoverability is following a size-biased sampling model. Cumulative ounces of discovered gold indicate that an asymptotic value has been reached where exploration is not expected to add significantly to known reserves. This is substantiated by a downward trend in the exploration success ratio of the number of new deposits discovered versus the number of new mineral prospects. The set of discovered deposits reflects a non-random sampling process where size- biased modeling suggests that the largest deposits will be discovered early in the exploration effort. It is the exceptionally large deposit contributing to the observed size-biased distribution. Although this pattern is observed for the western Abitibi the model is complicated by recent, large reserve additions that are attributed to the original discovery. There is present in this area a subtle learning process in exploration leading up to the largest discovery. For comparison a learning model was estimated using cumulative size of discovery per unit of time. This model yielded results consistent with the statistical trends and is thought to be a superior forecast of future discoveries in this region.

Jan 1, 1992

By M. Tirmarche, J. Brenot, J. W. Piechowski

INTRODUCTION Statistical analysis of results obtained by workers survey is very often limited to the determination of the collective dose and mean annual values. This information is not sufficent by itself for radiation protection purposes since the cumulative exposure of a worker during his working life is not taken into account. A more complete analysis would be obtained by considering both: [ ] These two notions are different. The former depends on the evolution of the protection with time and is related to annual limits (ICRP, 1977 and ICRP,1977 a). The second depends mainly on the works performed during the period of survey, the interference of protection evolution is weakened. So it is useful to foresee how the individual average annual doses would be when considering survey periods of 5, 10 years, or more. STUDIED POPULATION In order to analyse the two previously mentionned notions it is necessary to follow up a well defined population of workers which is continuously exposed to the radiological hazards on a long enough period. The selected population is that of the workers of the French uranium mines always present during the 1971-1979 period (9 years). The number of individuals is 937. The radiological hazards are: 1. exposure to radon and short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation. The workers of the uranium mines are exposed to these radiological risks in different ways according to the work performed. It is therefore necessary to subdivide the population into more homogeneous groups with respect to the radiological risks. Three groups are considered: - Group 1 : 227 individuals whose radon and dust exposures are always nil - Group 2 : 449 individuals whose radon and (or) dust exposures are different from 0 every year - Group 3 : 261 individuals represent a mixed category. Some features of these groups are given in table 1. [ ] The 937 followed individuals represent approximatively the half of the whole population of the French uranium mines. Taking into account the procedure adopted to select the studied population, it appears clearly that this population is not representative of the whole miner population. DOSIMETRIC RECORDS Three risk indicators are considered .Individual annual exposures to radon and its shortlived daughters. They are determined by ambient monitoring based on radon concentration measurements and recording of the times elapsed in the various workplaces. For each worker the annual exposure is represented by the mean annual air concentration and is expressed as a fraction of the maximum annual concentration (MAC). Given the administrative arrangements and the effective state of equilibrium between radon and its daughters, the maximum annual concentration is practically equivalent to 1 Working Level = 2.08 x 10- 5 jm-3. (UNSCEAR, 1977). . Individual annual exposures to long-lived ore dust which are also expressed in fraction of the maximum annual concentration. . Individual annual doses of external irradiation (X and [y] rays) expressed in mSv (= 10-3 Sievert). Irradiation monitoring is based on use of individual film badges.

Jan 1, 1981

By Wang Xifu, Zhang Daxian, Zhang Youdi

In mine haulage system, the surge bunker or stockpile installed between two facilities can raise the system production capacity. The arrangement of surge bunker has great relation with the capability development of the whole haulage system and the economic benifit. In the haulage system, surge bunker plays a role of surge capacity, accident capacity and technology capacity. In this paper, the variation of the material in surge bunker is analysed while the mine haulage system is working, the calculation method of the whole output is raised. With the goal of the maximum system output, the method of deciding the rational size of surge bunker is put out. In case study, the system output in Huolinhe surface mine is calculated, thus the rational size of surge bunker in huaulage system is decided.

Jan 1, 1996

By G. Barbery

A review is given of the present applications of random sets and integral geometry in fragmentation and liberation models of ores and minerals. Although attempts have been made in the past to apply such mathematical techniques to the comminution of solids, it is shown that it would not result in major progress. In liberation modeling, it is demonstrated that the approach can lead to fruitful results. Following a recent paper by Davy (1984), a model of liberation prediction is developed that can be calibrated for ore texture and breakage using image analyzers. The model is demonstrated for the case of a Poisson polyhedra ore texture and monodisperse fragment size. The model enables prediction of the complete composite particle distribution and thus is valuable for integration of ore breakage models with minerals separation models.

Jan 1, 1988

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986

By Allan Neal, Jess W. Smith

FirstMiss Gold Inc., formerly FRM Minerals, Inc., is heap leaching gold from difficult, low grade ores at the Getchell Gold Mine in Humboldt County, Nevada. A two-thousand ton per day facility is leaching material from waste dumps from old operations and from small, satellite deposits around the main orebody. A three-thousand ton per day pressure oxidation mill is under construction to treat sulphide gold ores in the main deposit. The Getchell gold deposit occurs in a wide fault zone in carbonaceous, calcareous sediments and intrusive rocks. Intense clay alteration is typical within the mineralized zones. Silicification is a less dominant alteration phase within the ore. Gold in the upper oxide portion of the deposit occurs both in a free state which is leachable and complexed in fine disseminated pyrite which is not leachable. Gold in the lower sulphide portion of the deposit is almost entirely complexed in pyrite. Abundant arsenic sulphides and variable amounts of remobilized carbon are associated with the gold mineralization throughout the deposit. The waste dump material being heap leached was derived from the upper portions of the gold deposit. The dumps contain high quantitites of fines, clays and sulphides of iron, arsenic and other trace elements. No stockpiling of low grade materials was attempted during the old mining operations, therefore, the dump material is highly variable and unpredictable. A sample of representative material from one dump contained the following:

Jan 1, 1998

By John C. Cook

In reasonably dry rock, long-wave radar can theoretically explore to distances approaching 75 meters (250 ft). High-resolution radar reflections have already been demonstrated through 13 m of hard limestone, through 9 to 18 m of coal in place and through 225 m of rock salt, using only low-power experimental radar equipment. Radar reflections have been received through the rock from rough pillar walls, from faults, and from a slim, uncased, vertical drill hole. In three years of intermittent experimentation, the feasibility of rapid radar exploration of large volumes of rock, with portable equipment, in deep, wet workings has been demonstrated. With future, improved equipment the theoretical working range, of the order of 75m, is expected to be attained in most hard rocks. THE TECHNIQUE Fig. 1 illustrates an early "monocycle" radar system (1) set up in a coal mine. This radar equipment is entirely different from that employed for detecting distant objects through the atmosphere. However, the basic principle is the same: a pulse of electromagnetic energy is radiated by the transmitter, a portion is reflected by some "target" object embedded in the surrounding medium and some of this energy is collected by the receiving antenna. In the receiver, the pulse is amplified, is "stretched out in time" by a sampling process, and is displayed on the screen of a cathode-ray oscilloscope. It may also be recorded on paper or magnetic tape. Fig. 2 illustrates a

Jan 1, 1997

By K. Oraee

Zarshuran gold deposit, with the total reserves of some 12.5 million tons of 4.18 g/ton ore, is considered to be an important gold mining project in the area. In this paper the feasibility studies of the whole project is carried out on the basis of several economic variables. Given that mining data are often of uncertain nature, these economic variables have therefore been estimated under the conditions of uncertainty. The resultant Net Present Value is hence also obtained under the same conditions. For this purpose, a model is first devised with the help of Excel and COMFAR software. The model is then developed that considers different scenarios which would result in different expected values for the economic variables. It is concluded that the NPV of the project is most sensitive to gold and silver price and that other variables such as discount rate, operating and capital cost all affect the feasibility of the project with lower degree of severity. Finally, risk analysis is also carried out using Mont Carlo technique, in order to estimate the most probable value of NPV. The average NPV calculated in this way is US$ 49.7 Million, whilst without due consideration of risk, this would be US$ 36.6 Million. The techniques used, together with the procedures adopted in this paper, can be used in feasibility studies of all mining projects. Such decision would result in more accurate Net Present Values than expected from other frequently used methods.

Jan 1, 2011

By Jurgen H. L. Stuve, Rick E. M. Widelski

Any one who has been involved with the mining or the treatment of gold-bearing ores will agree that at the end of the total process, the quantity of gold recovered is never as much as was expected. These short falls are usually explained away by claiming that:- the original evaluation of the ore being mined was inaccurate the plant treatment process is not at its optimum theft is taking place excessive dilution occurs during mining The truth of the matter is that the gold is being "lost". During all the stages of its production, starting from the mining, right through to the smelting process, a certain amount of gold is not recovered. When a newly found gold deposit is being evaluated and the drilling data being analysed, cautionary factors are applied so that the grade is not over-stated. Once the decision has been taken to start mining and development is in progress, the exposed ore is sampled. When Again, when this data is being analysed more safety factors are used to ensure that when a piece of ground is given a block-value, the gold content is not over estimated. mining actually takes place and the ore transported to the plant for treatment, the metallurgical department also introduces certain safety factors when predicting how much gold will be recovered. This shows that the quantity of gold that one expects to finally recover is already a conservative figure. The actual quantity recovered invariably falls short of this figure, in fact, South African gold mines are satisfied when achieving a Mine Call Factor (MCF) of 85%. In the last few years a great deal of work has been carried out to investigate how this unaccounted for gold is lost and what steps can be taken to remedy the situation. Previously mined areas were re-swept using the traditional hand brush method; experiments were carried out with water jets sometimes in conjunction with compressed air and even small portable vacuum cleaners were tried. None of these methods were totally successful in recovering the left over gold but the use of vacuum systems showed the most potential. the In South Africa this has resulted in introduction of high-powered vacuum systems on the gold mines to suck-up this lost gold. These were initially introduced in the mining areas, particularly old areas, to recover any left over ore. The results proved extremely profitable, So much SO that presently, well over 120 suction systems are doing this type of work. This success encouraged plant operators to look at areas of potential loss in the plant itself. This has resulted in an increasing number of machines being supplied to gold plants mainly for clean-up applications with the bonus that the material sucked up invariably contains gold.

Jan 1, 1993

By Steven J. Luzik

Introduction From 1973 through 1986, a total of 12 fires involving oil-flooded rotary screw compressors (OFRSC) were reported to the Mine Safety and Health Administration (MSHA). Most of these incidents were attributed to faulty or by-passed safeguards, or improper maintenance. The cause of a fire in an OFRSC is unique when compared to other types of compressors. A compressor inspection checklist is provided here that can be referenced when conducting regularly scheduled maintenance operations. This checklist and a well-planned program of periodic training and maintenance should help minimize the probability of fires and explosions in OFRSC's. Operation A rotary screw compressor operates on the principle of positive displacement of air. Compressed air in this type of compressor is produced by the meshing of two helical rotors, or screws, as they rotate within a steel housing called a stator. The male rotor normally has four lobes and is driven either directly or indirectly - through a gear assembly - by a motor. It intermeshes with a female rotor having six cavities. Figure 1 explains the compression mechanism: (1) Atmospheric air is drawn into the stator by the suction action of the two rapidly rotating rotors. (2) As the rotors rotate past the intake port, air is trapped in the stator and in the cavities between the rotors. (3) Further movement of the rotors causes an increased reduction in volume, compressing the entrapped air. (4) Compressed air is expelled at the discharge port in the bottom of the stator at a pressure and quantity determined by the particular compressor rotor design parameters, such as length, diameter, and speed. Radial bearings on the male and female rotors compensate for radial loading on the shaft and position the rotors within the stator. Thrust bearings on the discharge end of the compressor prevent rotor misalignment due to thrust developed during the compression cycle. This design prevents the male and female rotors from making contact with each other or the stator. A clearance of 0.07 to 0.1 mm (0.003 to 0.005 in.) exists between the two rotors and the stator. For this reason, there is virtually no wear on the rotors or stator, and the unit is relatively maintenance-free. Oil is injected into the compressor and serves to cool, seal, and lubricate. When air is compressed from atmospheric pressure to some higher discharge pressure, a specific amount of heat is produced. This heat is sometimes referred to as the adiabatic heat of compression. It is partially removed by injecting oil into the compression chamber. Premachined strips - a raised surface on the male rotor and a

Jan 9, 1988

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By G. F. Ayakwah

Point load strength (Is50) and slake durability (ID2) indices provide a measure of the strength and durability of rock fragments and are related to the alteration intensity and frictional resistance of the materials. Samples were collected from the rock piles, alteration scars and debris flows at the Questa mine with the purpose of examining relationships between Is50 and ID2, mineralogy, chemistry, weathering, hydrothermal alteration, and other geotechnical parameters. The Is50 from the various rock piles ranges from 0.6-8.2 MPa and the ID2 ranges from 80.9-99.5%. The Is50 and ID2 results indicate that the samples from the debris flows are stronger (average Is50= 4.0 MPa and ID2= 98.4%) than the rock-pile samples and that the alteration scar samples are weaker (average Is50 = 2.8 MPa and ID2 = 89.2%) than the rock-pile samples, but still most of these rocks are strong in terms of their Is50 and ID2. The Is50 decreases as the degree of alteration increases in some rock pile and alteration scar samples, but not in all. However, the majority of the rock fragments within the rock piles still indicate high strength, even after 25-40 years of weathering.

Jan 1, 2009

By F. C. Schwerer, C. R. McKee, J. C. Seccombe

Production of methane from coal seams requires hydrofracturing, and the length of a hydraulic fracture determines we11 spacing. Since the volume of fluid injected is known, the fracture length is the volume divided by average width and height. If the fracture is contained in the known height of the seam, then fracture width becomes the major factor con- trolling length. Width is proportional to coal compressibility; bulk compressibility is known to be larger than intrinsic compressibility. A method is given here to measure in-situ compressibility (a) from transient pressure testing. Theory linking flow in porous media with rock mechanical properties is reviewed. A consistent derivation of the porous flow equation is given incorporating 3-D deformation and the effective stress parameter "st' linking changes in effective stress and pore pressure. The relations for "st' in terms of a and intrinsic compressibility (ai) are substituted into the field measured porosity-compressibility product (net) and solved for a, the constrained matrix compressibility. In a field example, using 4 wells with an anisotropic analysis, the ratio of major to minor permeability was 17 for the Pratt A seam. a was found to be 6x10-5/psi as opposed to the laboratory value of 1.4x10-6/psi.

Jan 1, 1986