Search Documents

By J. Engesser

This paper discusses the effect that water chemistry, and water treatment have on pre-fired pellet quality and bentonite-binding effectiveness. A discussion concerning the effect that water temperature, water chemistry, water treatment, and surface area have on disc filter productivity and filter cake moisture is also included. This report is a summary of the data that were presented in five previous research reports, which are listed as references in this paper.

Jan 1, 2003

By R. Schuerch, C. Cimiotti, G. Anagnostou, J. Nickerson, P. Perazzelli

"This paper presents experiences gained from the construction of the Lake Mead Intake No. 3 project. The 4.7 km long tunnel was excavated with a hybrid TBM (able to operate in both closed and open mode). The tunnel crossed metamorphic and sedimentary rocks under a hydrostatic pressure of about 14 bar. During the excavation of the tunnel the TBM encountered difficult ground conditions caused by a combination of high water pressure, poor ground quality and locally low depth of cover. The adverse conditions required the TBM to be driven in closed mode at very high support pressures (10 – 15 bar) for approximately 60% of the tunnel length. The paper summarizes the main problems encountered during TBM excavation and analyzes the evolution of the TBM parameters over the entire tunnel length. INTRODUCTION The Lake Mead Intake No. 3 project is located approximately 30 km away from the city of Las Vegas in Nevada, USA. The project consists of the construction of a deeper third intake for the biggest reservoir in the United States, which is formed by the Hoover Dam. The construction of the new intake was required due to the constant drawdown of the lake level (more than 40 m in the past 20 years) and the consequent risk that the shallower intakes 1 & 2 may run dry. The project included the fabrication and positioning on the lake bottom of an intake riser, the excavation and lining of a 185 m deep shaft and construction of a 4.7 km long tunnel. One peculiarity of the project is that the water table is located about 140 m above the tunnel elevation (i.e. corresponding to a hydrostatic pressure of 14 bar at the current lake level). The tunnel was constructed using a tunnel boring machine (TBM) able to operate in both open and closed mode (Mc Donald & Burger, 2009). The present paper focuses on the TBM tunneling experience gained from the Lake Mead Intake No. 3 tunnel. The TBM excavation started on December 27, 2011 and finished on December 10, 2014 with the breakthrough to the intake structure at the bottom of Lake Mead. GEOLOGICAL CONDITIONS The assessment of the ground conditions encountered during construction was mainly based upon qualitative descriptions of the tunnel face conditions (during open mode operations) and analysis of the extracted muck (during closed mode operations)."

Jan 1, 2016

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By Hiroyuki Tamaru, Futoshi Kusumoto, Kosuke Tanimura, Atsuyuki Kimura

"SUMMARY The Hachinoshiri tunnel is a 2,469 m long two-lane road tunnel on the Chubu-Odan Expressway. Since more than 70% of the total tunnel length consists of low strength rock masses the competence factor of which is less than 1.0, it is expected that a self standing span cannot be achievable because of no ground arch to be established. The tunnel was thus designed with tunnel support patterns forming multi-arc early ring closure that can develop the load-carrying capacity estimated from the exerted earth pressure, Po, which can result from the competence factor, cf. The tunnel support pattern was selected based on the competence factor at tunnel face, then the subsequent tunnel support patterns were determined with reference to the monitoring data. The tunnel construction adopted full-face excavation accompanied by early ring closure using a 330 kW road header. The proposed construction methods at this tunnel site have turned out ensuring tunnelling in massive squeezing rock, so that they can be verified as reasonable tunnelling technologies, clarifying the relationship between the characteristics of the mechanical behaviour of the tunnel and its design parameters. INTRODUCTION The presence of highly weathered mudstone having the competence factor less than 1.0 where the tunnel became unstable with the early ring closure having the distance to early ring closure, Lf, of 6 meters, resulting in difficulty in maintaining the inner section of the tunnel, prompted a substantial amount of high strength double support and replacing of the tunnel support (Sato et al., 2015). Based on the mechanical characteristics learned from the construction, the mechanical stability of multi-arc tunnels was investigated using 3D FDM analyses with respect to the ratio of the radius for early ring closure, r3/r1, and the distance to early ring closure, Lf, so that tunnel support patterns for early ring closure can be established in terms of the competence factor, of, which was employed for a 725 m long section. Consequently the tunnel support patterns for early ring closure which can be determined from the competence factor became applicable to tunnel construction. The relationship between the characteristics of the mechanical behaviour of the tunnel and its mechanical parameters was also clarified. The early ring closure method adopted ensured tunnelling in massive squeezing rock, verifying its effectiveness in stabilizing the tunnel."

Jan 1, 2016

By Alexander N. Winchell

"The deposits of the east end of the Mesabi Range cover very large areas, and consist of the same taconite that produces the hematite of the central and western Mesabi. It is not deeply covered with drift, but outcrops boldly in large masses. It is not concentrated locally into enriched bodies separated by leaner areas, but is all a fairly uniform, hard, banded, unaltered chert, carrying about 25 to 30 per cent iron as magnetite.The Mesabi Iron Company, organized by Hayden, Stone & Co., and under the direction of D. C. Jackling, has taken over these deposits and is building a Concentrating plant at the new town of Babbitt, about fourteen miles east of Mesaba, Minn. This plant is to have a capacity of 2,000 to 3,000 tons per day, and is based on the application to this low grade material of the methods which have made the so-called porphyry copper properties so successful.In 1916, an experimental mill was built in Duluth; containing full sized machinery and capable of handling from 100 to 200 tons daily. A considerable tonnage of material was concentrated here during 1916, 1917 and 1918. The work showed that the resulting product could be varied, almost at will, between 60 per cent and 70 per cent iron and .006 per cent to .030 per' cent phosphorus, and that this could be made on a large scale well within the limits of cost set by iron trade conditions. A small special cargo was sent down the lakes, late in 1918, assaying 63.27 per cent iron (natural and dry) and .008 per cent phosphorus; but it is assumed that large scale shipments will normally be of a Bessemer' grade carrying about 63 per cent iron and .020 per cent to .030 per cent phosphorus. This material is a sinter, carrying only traces of sulphur and titanium, with silica between 6 per cent and 10 , per cent, and alumina, lime, magnesia, and manganese, each below 1 per cent. Some of the iron in this sinter is hematite and some is magnetite, the percentages varying according to the treatment given on the sintering machine. Like the analyses, this hematite percentage is within reasonable control. Sinter made from finely ground magnetite has much the structure of coke, being firm yet porous, and gives good account of itself in the blast furnace."

Jan 1, 1920

By S. Ilyas

Technical innovation in electrical and electronic equipment with new functions and design, stimulate consumer?s purchasing desire towards the latest equipments and this leads the rapid increase in the production of increased amount of waste materials Treason et al (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category; this emphasizes the need for efficient recycling strategies. Recycling of electronic waste is an important subject not only from the point of waste treatment but also from the recovery aspect of valuable materials. However, recycling of electronic scrap is still quite limited due to the heterogeneity of the materials present in the products (Veit et al. 2005). A bioleaching based process offers a number of advantages compared to the conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). The advantages include simple, inexpensive (in some cases) and eco-friendly approach besides, generation of less active leach residue then other metallurgical processes. Though, biohydrometallurgical process has been successfully applied for the leaching of metals from ores (Olson et al. 2003; Rawling 2000), data pertaining to its application for the extraction of electronic scrap is still scanty. Recently, a few studies have been undertaken for extraction of metals from electronic scrap/printed circuit boards (Brandl et al. 2001; Faramarzi et al. 2004; Choi et al. 2004, Ilyas et al. 2007; Ilyas et al. 2010). These studies were conducted with mesophilic chemolithotrophic (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans) or cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has the following advantages: (i) ability to grow under higher pH, and thus is more suitable in bioleaching of alkaline solid waste (ii) a generally faster leaching process with shorter lag phase (iii) Chelation of excreted metabolites (e.g. organic acids) with metal ion, thus reduce its toxicity to the biomass (Burgstaller et al. 1993; Aung and Ting 2005). The specific objective of this work was to; ? Collection, isolation and enrichment of fungal strain ? Evaluate the abilities of Penicillium chrysogenum to leach metals from electronic scrap at various leaching modes (one-step bioleaching, two-step bioleaching, spent medium leaching, fresh medium leaching, leaching with deionised water and chemical leaching). ? Comparative study of all leaching modes

Feb 27, 2013

By J. -F. Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

Jan 1, 2011

By D. Jacobson

There are many different machine setup parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the eccentric speed at which the cone gyrates. In June 2012, pilot tests were conducted on a 200 hp high speed cone crusher to determine the production and operating conditions over a wide spectrum of eccentric speed. Every plant will have variations in the ore characteristics and feed rates throughout the life of the mine, and at times throughout a single shift of operation, which result in non-optimal use of the crushing energy and inconsistent process control. For high speed cone crushers, the crusher will exhibit a different capacity, power required, and discharge size distribution as the speed ranges over the design limits of the machine. This study documents the measured variation in production and energy efficiency both when the crusher was ran at full capacity as well as when the feed to the crusher was not sufficient to run at full capacity. Overall, the results match theory and the capacity and power fluctuated by 25% and 17%, respectively, over the speed range when operated full while there was an overall trend of slightly coarser discharge size distribution as the speed decreased. The results with the fixed feed rate were more telling, as the crushers had 4-14% higher production when making a theoretical minus 12.5 mm product when operating at the optimal speed as compared to the worst speed in the ?typical? speed range for this application. Secondary analysis of the fixed tonnage testing also showed that the power draw was more consistent with lower magnitude spikes at the higher speeds (higher cavity level), as on average the standard deviation of the power draw increased from 7% to 18% and the peak power spikes from 20% to 48% over the speed range tested. The findings lay groundwork for more efficient plant design. Varying the speed of the crusher can be used to tune the crusher speed during commissioning, adapt to changing ore conditions over long periods of time, or be used as a dynamic input into an advanced control system. Each action above would serve to make the crusher(s) more productive and more energy efficient, and would also have mechanical benefits for the machine. Key Words: cone crusher, ore reduction, process control, crushing efficiency

Feb 27, 2013

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve's life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young's modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By S. K. Kawatra

Three International Symposiums-the 14th International Minerals Processing Congress, the 17th APCOM, and the SME-AIME Fall Meeting special symposium on Design and Installation of Com¬minution Circuits-held in 1982 contained a number of papers relating to the fundamentals of processing coals and metallic minerals. In addition, many papers were published elsewhere in the literature. Some of the more significant papers are discussed below. Flavel reviewed key performance parameters, such as energy-size relationships for crushing processes and presented a fundamental basis for optimizing crusher productivity and possibly for development of improved crushers. Pascoe et al. reviewed the use of such control schemes. Magerowski and Karra presented a paper on a computer program developed to and in the design of crushing circuits. The problems associated with the scale-up to very large ball mills were discussed by Arbiter and Harris, and by Kavetsky and Whiten. Both groups concluded that limits on mill productivity arise due to problems associated with particle breakage and transport through mills. Austin et al., and Herbst and Rajamini reviewed the state of the art for the use of grinding circuit simulators for design and control. The effects of mill operating and design parameters on selection and breakage were discussed in detail. The philosophy of control and instrumentation for grinding circuits was extensively discussed by Kawatra and Seitz. Their paper presented for the first time an analytical basis for the inferential particle sizing technique and provided a fundamental basis for the implementation of this technique. The effect of reagent addition variation's on the performance of coal flotation circuits was reported by Kawatra and Waters, and on sulfide flotation circuits by Klimpel et al. Both groups analyzed circuit behavior from a kinetic point of view and reached similar conclusions on the effects of collectors and frothers. The computer simulation of an iron ore flotation circuit also was reported by Kawatra et al. In this work particular attention was paid to the phenomena of froth overloading. Klimpel et al., Kawatra and Waters, and Niemi et al. discussed the philosophy of control by flotation circuits from a fundamental kinetic point of view. An extension of the use of high intensity magnetic separators to the beneficiation of specular hematite was discussed by Thayer and Linkson.

Jan 5, 1983

By David R. Quigley, Patrick R. Dugan

First reports of microbial coal solubilization appeared in the early 1980's (Fakoussa, 1981; Fakoussa and Truper, 1983; Cohen and Gabriele, 1982). These degradations, which occurred at ambient temperature and pressure, resulted in a dark brown to black viscous liquid and required days to weeks to occur. Rates and degrees of coal biodegradation varied from coal to coal. Hard coals were not extensively degraded (5-7%) while low-rank coals such as Leonardite, a sublignite, were completely solubilized. A correlation between degree of weathering or oxidation of coal and the coals susceptibility to biological attack was observed. This led to oxidative pretreatments as a method to enhance microbial degradation of coal (Strandberg and Lewis, 1986). Products of microbial degradation of coal are water soluble solids that do not have significant solubilities in organic solvents (Wilson, et. al., 1987; Quigley, et. al., 1987; Quigley, et. al., 1988a). Solutions of solubilized coal did not separate or form precipitates which suggested that they were true solutions and not colloidal suspensions. Biosolubilized coal contained more oxygen than starting material suggesting that microbial attack of coals involved oxidative cleavage of carbon-carbon bonds. This small change in oxygen content was the only change observed in coal structure during the biosolubilization process. Many coal solubilizing microorganisms have been isolated. Some are lignin degrading organisms such as Phanerochaete chrysosporium and various Streptomyces species (Gupta, et. al., 1988; Wilson, et. al., 1987). This was not unexpected since the structures of lignin and low-rank coals are similar. These organisms produce an enzyme complex, ligninase, that utilizes hydrogen peroxide to oxidatively cleave the bond between a and ß carbons of an aliphatic chain bound to an aromatic nucleus. Another important organism is Trametes versacolor (syn. Coriolus versacolor, Polyporus versacolor). Even though this organism produces a ligninase (Dodson, et.al., 1987), coal solubilization has been attributed to the enzyme laccase (Pyne, et. al., 1987). Laccase utilizes molecular oxygen to oxidatively cleave a - ß bonds using a mechanism similar to that observed for ligninases (Kawai, et. al., 1988). Other coal solubilizing microorganisms have been isolated from coal outcrops (Ward, 1985; Ward, 1988), but enzyme activities responsible for coal solubilization have not been identified. Research at the Idaho National Engineering Laboratory has focused on those mechanisms involved in coal biosolubilization. An

Jan 1, 1989

By Michael Drozd

Introduction Flotation is a recovery process that utilizes natural or chemically-introduced hydrophobicity of minerals to separate ore from gangue by attaching the ore particles to bubbles. Flotation has been known since 1906, when it was patented by E. L. Sulman, H. G. K. Pickard and John Ballot. Flotation's first documented plant use was in 1911, when it was used on gravity tailings from a zinc plant. Cyanide leaching was first patented in 1887. Most early precious metals flotation was linked to lead or copper concentrates. Most precious metal flotation is linked to sulfide recovery and utilizes such reagents as xanthates, dithiophosphates and thiocarbanilides. But the involvement of flotation in precious metals recovery does not have to be limited to active flotation of the gold and silver bearing minerals. Flotation can be used to remove interfering minerals, such as carbon, or cyanicides, such as copper, arsenic bearing minerals or other cyanide complexing minerals. Cyanide Leaching The use of cyanide to recover precious metals is the backbone of the industry. The various recovery processes that use cyanide are: 1. Leaching-Counter Current Decantation(CCD) Merrill-Crowe 2. Carbon-in-pulp (CIP) 3. Carbon-in-leach (CIL) 4. Vat leaching 5. Heap leaching These processes are selected depending on ore grade, ore leaching characteristics, reserve size and capital limitations. Ore grade is used as the first criteria to determine the type of cyanide plant required. However, the reserve size can determine whether a ground ore alternative is used. The ore leaching characteristics may indicate that the higher recovery, associated with a process that employs grinding, is the only economic recovery alternative. There are some extremely large leaching plants with grades that would be non-economic for some existing heap leach plants. Many factors, such as strip ratios, metal recovery and reserve size, determine what the ultimate plant design will be. The exact processing scheme that is used, is a multifaceted decision matrix, which gives the process metallurgist some job security. Precious Metal Recovery Using Flotation Flotation recovery can conceivably be used on any ore that has been ground. Many operations utilize gravity separation on the ore to remove native gold from the ore prior to sending it to cyanide leaching. On certain ores, where the gold is in visible nuggets or particles, this processing alternative is advantageous because the native gold cyanide recovery is

Jan 1, 1993

The National Mining Hall of Fame and Museum in Leadville, CO seized the opportunity to show off during its 10th anniversary induction banquet on Sept. 6. "We wanted to make people more aware of the mining hall of fame and museum," said Carl Miller, its executive director. The annual event honors inductees into the Mining Hall of Fame. This year, the inductees included Paul Wheeler Allen, Joseph Rosenblatt, Arthur Fay Taggart, Joseph Toy, Joseph Wharton and John Benjamin Zadra (ME, August, pp. 60-63). Allen, of Pasadena, CA and Rosenblatt, of Salt Lake City, are both living. Only Allen was able to attend. This year's induction banquet was the first held in Leadville, North America's highest incorporated city, at 3,094 m (10,152 ft) above sea level. The banquet gave attendees an opportunity to see the museum in its century-old 6,500-m2 (70,000-sq ft) Victorian schoolhouse. Many of the 350 guests came in 1890s dress to the black-tie affair. The evening included a cocktail reception and an open house along with a catered, prime rib dinner. During the open house, attendees had the opportunity to tour the museum's 12 rooms of exhibits and displays. Among items of interest, it was noted that a framed directory of inductees now enhances the entrance to the hall of fame. The directory is organized by the inductees' names and the location of their plaques, allowing visitors to quickly find hall of fame members. Noted mining historian and author Duane Smith delivered the keynote address at the banquet. After the induction of the six honorees, attendees danced to the big-band era music of the Leadville 17-piece band BandAge. Karl Elers was the master ceremonies for the evening's program. He is a member of the hall of fame's board of directors and is chairman of Battle Mountain Gold Co. Allen was honored by the presence of 26 former colleagues and associates. He told the audience that he originally thought the museum should have been located in Denver. "But I have been proven wrong," he said. For many years, Allen was the operational executive of Cyprus Mines Corp. and a key participant in the company's growth. Allen received a replica of his mining hall of fame plaque from Thomas Falkie, chairman of the hall of fame's board of governors and president of Berwind Natural Resources Co.

Jan 1, 1997

By David Hurth

JOHN HAMRIC: Our next topic leader is David Huth, superintendent of sulfuric power generation, DAP, and shipping for IMC-Agrico, Nichols Plant, Mulberry, Florida. With a title like that it's no wonder he believes in empowerment. His topic today is "The Triumphs and Pitfalls of Using Empowerment Techniques." DAVID HUTH: Empowerment and its benefits are a desirable alternative to the traditional management structure. The difference between the two is the amount of decision- making authority and responsibility given to individuals by a supervisor. Just what is empowerment and how does it work? Empowerment is relinquishing to individuals the authority and responsibility to make daily decisions. Can everyone be empowered? What if they make a wrong decision? Will I empower myself out of a job? These are questions that all managers have when they hear the word empowerment. In today's fast-paced and high-pressure business environment, the old way of managing people must be replaced with a new approach. No longer can we, as managers, make all the decisions. The increased work loads due to downsizing, consolidation, and synergies have stretched us too thin. What about our employees? How can we motivate them into the high-performance teams that our companies are demanding? What possibly could satisfy both these issues? The solution to these problems can be solved with the power of employee empowerment. Employee empowerment will not only lessen the load on managers but will build teamwork, motivation, and pride into the employees who work for the managers who use it. American business was rudely awakened in the early 1980s when the Japanese companies not only caught up to American companies but literally flew by them. America was fat, dumb, and happy after World War II. Why wouldn't they be? They had all the factories. Everyone else had to rebuild. So for 40 years American business lounged in the limelight of very little true competition. But times change. Unfortunately, American business did not. Now the cry to perform in the new global economy has come down from the corporate boardrooms. Down through the ranks it has been felt. Guess who is supposed to make it work? But where are all those people who are going to make this rejuvenation and corporate renaissance possible? Many of them are gone-lost in downsizing, synergies, and rightsizings

Jan 1, 1998

By William H. Sutherland

INTRODUCTION Coal workers' pneumoconiosis and sili- cosis are only two of several diseases which are rlassed as pneumoconiosis. These are respiratory diseases caused by dusts which are inhaled and accumulated in the lungs. The individual particles of dust cannot be seen by the human eye. They are so small that they escape the natural cleansing mechanism of the nose and air passages and make their way down to the terminal air sacs of the lung where they injure the cells and cause the formation of scar tissue. Consequently, if there is exposure to high concentrations of dust over a period of time - usually, a number of years - the amount of scar tissue increases and begins to impair breathing. As a result, the miner develops shortness of breath, coughing and wheezing ad-if exposure continues - this progresses to permanent disability and frequently to death. Death is often due to pulmonary heart disease, the effect of stress on the heart 2s it tries to compensate for the weakened lungs. Specifically, silicosis is an occupational lung disease caused by the accumulation of free silica (quartz) in the lungs. Silicosis is considered the most important form of pneumoconiosis, not only because of its seriousness as a respiratory crippler, but also because of the large number of workers who risk contracting it in a variety of occupations. Quartz is one of the most common substances of the earth's crust, estimated at about 60 percent. Silicosis has been found in coal, metal and granite miners, as well as in other workers, such as sandblasters and pottery makers. Silicosis is also known to predispose the lung to tuberculosis and to increase the chances that a worker will contract chronic bronchitis and emphysema. The seriousness of silicosis was tragically brought to public attention about 50 years ago. During 1932-34, workers were involved in digging a tunnel through rock at Gauley Bridge, West Virginia. While their exposure time was relatively short, they developed silicosis because of the high concentrations of quartz. By 1936, 476 workers had died of silicosis and about 1500 were believed to have the disease (Washington Post, 1982). It is difficult to tell how many coal miners have silicosis. Because x-rays and breathing function tests do not show the difference the type of pneumoconiosis is generally diagnosed by the miner's work history. For example, if a worker

Jan 1, 1986

By Paul C. Miclea

With the growing urban population and the concern for traffic congestion and pollution (emissions control), public transportation is becoming more and more attractive to both city dwellers and managers. To gain access to the central area of the city, the sub- way remains the most viable alternative, despite its higher cost when compared to above ground or elevated transportation systems. There are relatively few regulations and criteria for subway ventilation, particularly when compared with mine ventilation. The main document that provides guidance and general recommendations for subway ventilation and environmental control is the Sub- way Environmental Design Handbook, published in 1976 (2nd edition) by the U.S. Department of Transportation, Office of Re- search and Development. Many of the subway systems in existence today have been designed and built with ventilation features adequate for normal train operation, but their design does not consider stringent criteria for such emergency conditions as a train fire in a tunnel. The National Fire Protection Association's Standard for Fixed Guideway Transit Systems known as NFPA 130 as well as the ASHRAE Handbook - HVAC Applications (1995) provide specific design and operation requirements for subway ventilation systems. Some of the existing, old subways are upgrading their ventilation systems to comply with the new regulations. The ability of a particular ventilation system design to provide adequate ventilation during normal and emergency conditions can be evaluated using computer modeling and simulation techniques. A train fire will cause a sudden change in the tunnel ventilation pattern by adding an unsteady and fast-growing source of heat. The hot air and gasses created by a fire will tend to flow uphill, possibly against the normal flow, producing a 'backlayering effect." To prevent this effect from happening, enough ventilation must be provided and the governing criterion to establish the required airflow is called 'Critical Velocity." Several software packages are available for special applications on tunnel and station ventilation as well as to model the spread of smoke and heat in case of a major tunnel fire, using Computational Fluid Dynamics. This paper presents the current issues in subway ventilation, as shared by the public transit community around the world, together with modern alternative design concepts vis-à-vis the more stringent emerging Fire-Life Safety criteria. Examples of recent studies and ventilation systems design are provided.

Jan 1, 1997

By William E. Cobb

15.1 INTRODUCTION The mine development process, as discussed in Chapter 2, is a series of data gathering and analysis steps. As the mine development process proceeds, information about the geology, mineability, and metallurgy of a particular deposit is continually generated, along with environmental information regarding project permitting status. As data are obtained, checkpoint evaluations are typically conducted to determine the economic viability of the particular deposit. Although the project evaluation process was discussed at length in Chapter 2, a brief review of the process is presented here to "set the stage" for the discussion on economic analysis of heap leach projects. Figure 15.1 (MacKenzie, 1980) presents an overview of the sequential process of mine development. Once the deposit is discovered or acquired, an initial delineation program can be undertaken to expand the project's geologic, mining, and metallurgical data base. At the end of this initial program, the direction of the project is evaluated. The company can either abandon the project, postpone it, develop and mine it, or gather additional data in hopes of improving the project's economic viability. If the company continues gathering data, then another decision point and evaluation will be required. This process may continue until the company either decides to postpone the project or develop and mine it. A project may be postponed indefinitely, typically in hopes of improved metals prices. Certain holding costs, such as land or royalty payments, may be associated with postponement. In general, once a company goes through two evaluations, the project is less likely to be abandoned. For this discussion, it is assumed that the company will undertake initial, second, and third delineation programs to gather sufficient geologic, mining, metallurgical , and environmental data to justify a positive production decision from the second or third economic evaluation. The objectives of the first delineation program will be to confirm and expand upon the available information about the deposit. During the second delineation program, development funds should be directed toward identifying the critical project items (i .e., ore reserves, mineralogy, mineable grade, metallurgical recovery, etc.) that must be resolved before making the production decision. This second economic evaluation can be used to determine which metallurgical concept will be applied to the project: heap leach or a traditional agitation-type leach plant. If the proper work has solved key project concerns in the second program, a production decision may be made from that evaluation.

Jan 1, 1988

By J. A. Siekmeier

The thickness of the laminated beam modeled in this study is based on bridging potential and TDR measurements. The laminated beam stiffness is based on the effective stiffness of an equivalent transformed section. The maximum deflection of this near-surface laminated beam is compared with the maximum measured surface subsidence. The spreadsheet provides a rational technique to graphically display the character of the overburden and potentially allows prediction of a subsidence factor based on boring logs and the proposed mine plan. The U.S. Department of the Interior, Bureau of Mines (Bureau), utilizes a commercially available computer spreadsheet program in combination with a modified version of Bieniawski's Rock Mass Rating (RMR) system to characterize the geology overlying high extraction coal mines. The spreadsheet program calculates a RMR for each bed based on the lithology, thickness, and engineering properties, which are determined from boring logs and laboratory tests. Once the RMR is calculated the spreadsheet has two major functions. First, the spreadsheet calculates values used to graphically represent the character of each individual bed in the overburden. It calculates an in situ deformation modulus using an empirical rela¬tionship between the modulus and the RMR and then uses this effective modulus along with additional parameters that are based on mine geometry to calculate the bending stiffness and bridging potential for each bed. Second, the spreadsheet creates a transformed section that allows groups of beds to be modeled as an elastic beam. It then calculates a bridging potential for the entire rock mass. The bridging potential of the rock mass is a single value that takes into account both the geology of the overburden and the geometry of the mine. It seems reasonable that there would be a strong correlation between the bridging potential, the overburden response to high extraction mining, and the subsidence ratio. The results presented in this paper focus on the relationship between the bridging potential of individual beds and the deformation measured using Time Domain Reflectometry (TOR). Subsurface displacements measured over seven high extraction coal mines in southern Illinois were correlated with the bed stiffness and bridging potential profiles. Based on these correlations it was evident that the process of caving and subsidence over these high extraction mines involved momentary bridging by individual beds or groups of beds and the ultimate development of a laminated beam near the surface.

Jan 1, 1986

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017