Search Documents

By Brahm D. Prasad

As in other mineral deposits, variation in bitumen saturation, thickness of ore and discard occurs throughout Alberta's Athabasca Oil Sands deposit. The economic stripping ratio developed here to determine surface mineable limits takes into account capital and operating costs, crude oil prices, quality of ore, thickness of overburden, and thickness of inter-ore waste. The surface mining systems employed to remove bituminous sands (oil sands) from huge mines at depths of 60-70m use gigantic draglines, bucket wheel excavators and reclaimers, and large mobile equipment.

Jan 1, 1982

By T. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, ship-lap, etc. to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1989

By Alfred G. Hoyl

The author, in exploring a virgin area vertically in two known ore shoots requiring decline shaft sinking, drifting, crosscutting and diamond drilling, chose to use electric, electric hydraulic, and diesel rubber-tired equipment. A rebuilt hoist, and electric hydraulic shaft shovel (mucker), hydraulic sinking drills, single boom electric hydraulic jumbo, electric hydraulic LHD, and electric hydraulic diamond drill were used successfully. Slides of the equipment and its use are shown. The advantages and disadvantages of the equipment are discussed, together with costs and production.

Jan 1, 1984

By John Hardy

The performance of five dense-medium washers was evaluated in four preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation. The secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The sharpness-of-separation was excellent for all four primary separations and the secondary separation.

Jan 1, 1966

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980

By P. Worley

With Utah Power & Light Mining Division's commitment to operate the safest and most productive mines possible, a decision was made to purchase and install mine-wide monitoring systems for use in the mines. After review of several different systems the Conspec Senturion 200 system was chosen. Three separate systems were ordered to fulfill the monitoring requirements of the six mines in operation: one system for the Deer Creek Mine one for the Wilberg/Cottonwood complex, and one for the Deseret, Beehive and Little Dove complex.

Jan 1, 1989

By H. C. Juvkam-Wold

The design of an aquifer depressurization system is discussed. The system uses a number of wells surrounding a mine shaft to reduce the aquifer pressure in the vicinity of the shaft. The effect of various parameters such as number of wells, wellbore diameter, time and well location is discussed. It is concluded that, with a properly designed depressurization system, the aquifer pressure and the water inflow rate to the shaft may be reduced to less than 15X of their potential values in the absence of wells

Jan 1, 1980

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By F. Mielli

Mine operation managers are constantly tasked with identifying new ways to produce more, while using less. Mine effectiveness and reliability is the foundation of improving operational performance. Timely decisions need to be made in order to identify production waste. Intelligent data needs to be visualized in real-time. Operational events need to be captured with impacts quantified and root causes identified. Unfortunately, complex information technology solutions often have a very poor success rate, with some reports suggesting 30 percent of complex projects are canceled before completion.

Feb 27, 2013

By K. Wongaew, R. F. Cook, J. E. Carlson, T. Cleys, C. R. Smith

Steel fiber reinforced concrete segmental rings are the final tunnel lining for approximately 85% of the alignment for a 6.706-meter (22-foot) internal diameter tunnel being built as part of the East Side Combined Sewer Overflow Tunnel Project. This paper describes the approach adopted for the design of the steel fiber reinforced concrete segments, the development of the performance criteria for the segments, and the testing program used to confirm the performance of the materials and segments in the laboratory and in the field.

Jan 1, 2007

By Keith Schaeffer

This paper presents a history of the planning, engineering and construction completed for the railroad tunnel crossing part of the West Elizabeth Avenue Storm Drainage Project, undertaken to relieve flooding within the West Elizabeth Avenue area in Linden, NJ. The Railroad Crossing Contract is part of the larger Linden Drainage Improvements Project consisting of a new gravity storm sewer system. The improvements are required to provide additional storm drainage for the City of Linden and the Merck Pharmaceuticals manufacturing facilities in the City of Linden.

Jan 1, 2008

By K. G. Correia

The replacement of the dry mining method at Guajú Mine by the dredging method was a means of ensuring its feasibility by maintaining the production levels. Dry mining increased the cost of the deposit with the distance and presented a limited mined volume, while the decreasing grade of the deposit led to a production drop. With the new methodology, there was a considerable reduction in unit cost of the mine and an increase in the production level of a deposit with low heavy minerals content.

Jan 1, 2005

By John H. Raymer

Groundwater inflow into hard rock tunnels is strongly affected by recharge and drawdown of the water table. Previous analytical and empirical methods for estimating inflow have generally not accounted for these factors in an accurate or systematic way, resulting is wrong conclusions about inflow and the effects of the tunnel on the surrounding environment. This paper discusses these issues and provides some simple analytical equations to estimate inflow and water table drawdown around the tunnel. Examples from tunnels in the Atlanta area are provided.

Jan 1, 2005

By K. Taniguchi, Y. Inada

When underground openings are excavated in rock mass for storage of Liquefied Natural Gas, hereinafter referred to as L.N.G., as its temperature is -162o C, steep temperature gradients and thermal stress occur around the openings. That is, the plastic zone and cracks around openings will expand with time. In this paper, the range of cracks which were obtained by the Crack Analysis Method and the range of the plastic zone which was obtained by the No Tension Analysis Method were investigated and compared.

Jan 1, 1986

By Kurt Bryan, O&apos

The crushing and milling of mineral bearing ores can now be accomplished more efficiently through the application of WaterFlush technology. WaterFlush crushing has reduced capital and operating costs for the processing of a lead/zinc ore in South America. Similar benefits can be expected in the processing of other ores. WF cone crushers offer improved performance over conventional cone crushers. Performance improvements include the ability to crush wet and sticky ores, increased reduction ratios and greater production of flakier and finer products.

Jan 1, 1989

To preserve Washington Group International's quality of service in the mine operations area, the company has established a Supervisor Training Program to provide all levels of supervision with the required skills to meet objectives and guarantee consistent, excellent performance for each of our projects. A need developed to establish this training program internationally. The first international training session was held at the APEX San Cristóbal Mine in Bolivia. This paper discusses the program’s development, execution, results, and lessons learned with an emphasis on multicultural environments.

Jan 1, 2007

By Dennis R. Rice

The Kettle River Joint Venture is 70 percent owned by Echo Bay Minerals Company, a wholly-owned subsidiary of Echo Bay Mines Limited, and 30 percent owned by Crown Resources. Initial announced ore reserves were 700,000 troy ounces of gold contained in three deposits located east and north of Republic, WA., U.S.A. Additional reserves are being proven. Processing of finely ground ore by preaeration-carbon in leach (CIL) circuit was selected followed by cyanide destruction by the INCO Air/SO2 process.

Jan 1, 1992

By Donald R. East

In the planning and design of mill tailing disposal facilities, the chemical and physical nature of the fine­grained material to be disposed of has to be fully understood in order to create an efficient and safe long­term storage facility. Disposal of tailing has become the single most important source of environmental impact for mining projects and the development of many promising ore bodies has been delayed or even stopped due to problems of facility siting and design under pressure of increasingly stringent regulatory require­ments.

Jan 1, 1992

By James L. Hendrix, Michael R. Straka, Emil B. Milosavljevic, Ljiljana Solujic, Neil P. Gallagher

Analysts that utilize the classical distillation procedures for cyanide analysis are often frustrated by the poor reproducibility and repeatability of these techniques. Capital intensive business decisions and environmental management regulations are exas­perated by the fact that the EPA/ASTM approved cyanide deter­mination methods produce data of questionable quality. Reliable cyanide values are important in monitoring the effec­tiveness of the cyanide detoxification procedures. Efficiency and cost of gold and silver cyanidation recovery can also be improved by precise cyanide monitoring in the process itself.

Jan 1, 1996

By Brad Hewitt

Since Campbell Mine began processing ore, there has been a gravity gold recovery circuit. From 1947 to 1982, gravity gold was concentrated through the combination of jigs and mercury amalgamation. In 1982, jigs with concentrating table upgrading commenced and was utilized until the end of 1994. As of January of 1995 to the present, Knelson Concentrators in com­bination with concentrating tables have been employed to achieve a refinable product. An evaluation of the justification used for the last change is the focus of this paper.

Jan 1, 1996