Search Documents

By Lauren M. Roberts, Ralph R. Sacrison

The Meikle Mine uses long-hole open stoping and cut-and-fill methods with backfill as the primary ground support technique. The mine operates at 2,858 tonnes per day (3,150 tpd) and has sustained operation in excess of 3,175 tonnes per day (3,500 tpd). Consistent backfill production is critical in achieving these mining rates. The heart of the system is a 7.65 cubic meter (10-cyd) horizontal shaft ribbon mixer located 328 m (1,075 ft) underground. System control is through several PLC's, allowing for a high degree of automation and process flexibility. Aggregate feed is routed 257 m (842 A) through vertical drop pipes in the ventilation shaft, a rockbox, transfer raises, and then into either of two raisebored storage silos. The aggregate is crushed mine waste, nominally 70% 3.8 cm x 1.0 cm (1-1/2"x 3/8") and 30% -1.0 cm (- 3/8"). The binder is routed through a vertical borehole, surge bins, and transfer raises. The binder is a mixture of Type II cement and fly ash. Two primary manufactured fill designs are produced: a high strength mix for stopes which will be undercut; and a low strength mix for stopes with only rib exposure. The high strength target is 5.5 Mpa (800psi) unconfined compressive strength in test cylinders. The low strength target is 2.8 Mpa (400 psi). The systim has allowed consistent achievement of these targets, while experience has allowed reduced costs and increased efficiencies. Fill placement is through 6.1 cubic meter (8 cyd) LHD's dumping into stopes. Specific sills and cut-and-fill drifts are jammed to the back. System enhancements have included colloidal mixers for cemented waste slurry placement and transfer raises for sending manufactured fill to the lower levels of the mine.

Jan 1, 2001

By Stuart M. Lipofsky, Norm Hutchins

The Metropolitan Water District of Southern California has undertaken the Lake Mathews Outlet Facilities project to replace the existing outlet facilities. In the late1990s, consulting engineers for the District determined that the Lake Mathews Outlet Facilities were susceptible to a catastrophic failure during a seismic event. To ensure a reliable supply of water to Metropolitan’s customers in the Los Angeles area, the District decided to construct new outlet facilities. This Project consists of excavating a large diameter junction shaft, a 6.10 m (20 ft.) horseshoe tunnel, three short 4.88 m(16 ft.) horseshoe bypass tunnels, and a large excavation within a cofferdam that were all driven in difficult rock conditions. Additionally, a new concrete outlet tower was constructed and connected to the existing tunnel by the new bypass tunnels and through the junction shaft. The J.F. Shea Co., Inc. of Walnut, California, is currently finishing the construction of the Lake Mathews Outlet Facilities Project for Metropolitan. The large diameter junction shaft is 50.60 m (166 ft.) deep, excavated 16.15 m (52 ft.) in diameter and lined with a61 cm (2´-0?) thick steel reinforced concrete lining to a finished diameter of 14.63 m (48ft.). The shaft was excavated full face with one stationary shaft three-boom jumbo, modified for the large diameter. The shaft also consists of four sets of gate guides extruding from the shaft wall towards the center of the shaft that provide the ability to operate up to four mechanical gates at any time, to open or close each tunnel. This paper will present the junction shaft excavation and concrete construction techniques, including the innovative slip form method utilized to construct the junction shaft.

Jan 1, 2003

By Stanisław Lasocki

We present an algorithm to integrate the uncertainties of mean activity rate and magnitude cumulative distribution function in the interval estimation of the primary seismic hazard parameters: the exceedance probability and the mean return period. The algorithm is applicable for both the parametric and nonparametric modeling of magnitude distribution. When the Gutenberg-Richter relation-based parametric model of magnitude distribution is used, the interval estimation of its parameters is based on the asymptotic normality of the maximum likelihood estimators. When the nonparametric kernel estimation of magnitude distribution is used, we apply the iterated bias-corrected and accelerated method for the interval estimation, based on the smoothed bootstrap and second-order bootstrap samples. Previous studies indicated that the uncertainty of mean activity rate significantly affects the interval estimates of hazard functions only when the activity rate is low and the inference period is not long (Orlecka-Sikora & Lasocki 2017). With increasing mean activity rate, the uncertainty of magnitude distribution dominates over the uncertainty of mean activity rate in the aggregated uncertainty of the hazard functions. The provided algorithm is generic and can be applied to capture the uncertainty of any multiparameter function from the uncertainties of its parameters. Here we present a further development of the algorithm developed by Orlecka-Sikora & Lasocki (2017) by presenting its implementation in the Traffic Light System approach. As an example of use, we present the confidence intervals estimation of hazard parameters for the datasets related to induced seismicity accompanying underground exploitation of copper ore in the Legnica-Głogów Copper District (LGCD) in Poland. The algorithm is under implementation to the EPISODES platform (https://tcs.ah-epos.eu/) - an IT platform that provides access to integrated research infrastructures of the Thematic Core Service of Anthropogenic Hazards (TCS AH) of EPOS (European Plate Observing System). The algorithm is also a component of the pilot developed within the EPOS SP project (No 871121), which aims to strengthen the interaction with the private sector and the added value for society. The pilot demonstrates the potential of the IS-EPOS platform software applications for the technology-related probabilistic assessment of time-dependent seismic hazard. The pilot supports a Traffic Light System approach. The current seismic hazard is compared to threshold values based on the exceedance probability for a given magnitude.

Apr 26, 2022

By T. J. Lutz, J. L. Carr, J. A. Yonkey, C. C. Jobes

"Since 1984, the date of the first recorded fatality involving a remote controlled continuous mining machine, 38 miners in the United States have been killed when they were struck by a continuous mining machine. Proximity detection is a valuable tool for preventing fatalities, and the use of these systems is expected to significantly improve safety. Proximity detection provides a means to prevent accidents like these. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a series of underground tests to evaluate the accuracy and repeatability of proximity detection systems under a number of conditions such as varying the orientation and height of the personal wearable device (PWD), moving the PWD close to the trailing cable, and activating the machine’s mining mode. At the 2014 SME Annual Meeting, results from tests on first-generation proximity detection systems were presented. This paper will provide results from the similar tests performed with second-generation systems. The results show that performance has improved. For example, the negative impact of PWD orientation and the trailing cable has been reduced. However, some inconsistencies remain. Notably, performance changes dramatically when mining mode is activated. INTRODUCTION Since 1984 there have been 38 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM) [1]. In August 2011, the Mine Safety and Health Administration (MSHA) published a proposed regulation that would require proximity detection systems on all continuous mining machines except full-face machines [2]. Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHA-approved proximity detection systems are commercially available. MSHA estimates that of the 38 fatal striking and pinning accidents that have occurred since 1984 involving CMMs, the use of proximity detection could have been a preventative factor in at least 28 cases [1]. Furthermore, MSHA estimates that proximity detection could prevent 20% of all deaths throughout the industry [3]. NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system [4] and have recently conducted research intended to develop more advanced proximity detection technology for CMMs [5,6,7,8]. In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate [9,10] and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators [11,12]."

Jan 1, 2015

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By Shular R. Scudamore

There was a time when heavy-duty apron feeders were built to last almost forever. The machines were heavy and built to maintain certain expected longevity and reliability. Increasing emphasis on return on capital leads to cost-effective designs. Costs can be increased or decreased, depending on customer specifications and the design philosophy of the feeder manufacturer. Specifiers can make important contributions to cost effectiveness. To do so, this article describes what should be known about planning with a supplier for heavy-duty apron feeders. There are several factors that should be considered, including capacity, characteristics of material carried, length, method of feeder loading, degree of lift, hopper opening, pan construction, and type of drive. Today's apron feeders are built in various sizes and with a variety of components to handle heavy, lumpy, or abrasive materials that can ruin lighter feeders. Careful feeder selection is important if it is to provide a controlled feed rate, absorb huge impacts, be used with long hopper openings, and have a relatively low power-perton capacity. Variations in systems and materials demand that each feeder be designed for its application, drawing on a wide range of components. Therefore, certain factors must be considered before final specifications are drawn. Capacity The design and application of an apron feeder is based on how material passes through a given system over the feeder into processing machinery. The processing machinery's capacity governs other equipment and productivity of the flow. From this basic information, related sizes of upstream equipment can be determined. Of these, the apron feeder acts as the "mouth and neck of the bottle." No more will pass than the mouth and neck will accommodate. Everything in the apron feeder design, from dimensions to power, is based on processing machinery. Material Considerations Are Vital Just as the nature of materials to be crushed or screened affects capacity and productivity of a crusher or a grinding mill, so does it affect capacity and performance of a feeder. Lump size must be identified closely so the pan width can be selected to accommodate the maximum lump with room to spare. For example, a lump size of 760 mm (30 in.) indicates a pan width of 1.5 m (60 in.) While two times the maximum lump is considered minimum width, if the maximum lump

Jan 12, 1983

By Kwadwo O. Adutwum, George M. Potter, Todd J. Harvey

Ashanti Goldfields Company (AGC) is the largest gold mining company in Western Africa. Their jewel operation is a highly inte­grated set of mines and plants situated in Obuasi, in the Ashanti region of Ghana. This operation is responsible for mining 5.5 mil­lion tonnes of ore at 4.6 git annually from a series of open pits and underground mines. The sulphide ore is highly refractory with untreated gold recoveries in the range of 30-40%. The milling facilities are quite varied and include an oxide treatment plant (OTP), a heap leach, a sulphide roaster circuit (PTP), a tailings treahnent plant (TIP) and the most recent, a sulphide treatment plant (STP). The sulphide treatment plant, the world's largest stirred tank biooxidation circuit, was commissioned in early 1994. This plant treats approximately 800 tonnes of refractory gold con­centrate per day with overall recoveries of75-85o/o(ll, Biooxidation was selected for its ease of operation and less exotic maintenance requirements as well as its ability to achieve comparable gold recoveries. Unfortunately, despite stirred tank biooxidation being one of the lower cost methods of treating refractory ores, it is still too costly for low grade refractory materials. GeoBiotics, Inc. has developed a proprietary technology that allows the economic treatment of lower grade refractory gold ores through heap biooxidation. AGC has a significant resource of low grade refractory sulphide ore. This ore is too low grade to warrant BIOX™ sulphide treatment and its oxide plant recov­ery is low at 35-45%. GeoBiotics and AGC have completed pre­liminary testing and economic analysis of heap biooxidation for this material. Additionally, the feasibility of producing a gravity concentrate from the tailings of the sulphide treatment plant has been explored. This concentrate would be coated onto the low grade sulphide and biooxidized concurrently. Gold recoveries for the biooxidized low grade sulphide have increased to 75% and the gravity recovery from the STP tailings has achieved 80% uti­lizing a Falcon concentrator. The preliminary economics of the proposed full scale plant are very favourable with a pre-tax IRR of 233% and a payback period of 6 months. This paper details the biooxidation testing, flow sheet devel­opment and preliminary economics of employing heap biooxi­dation for low grade refractory ore treatment at Ashanti Goldfields' Obuasi operation.

Jan 1, 1998

By K. Adam

The sustainable management of solid wastes, including the wastes emanating from portable batteries, consists one of the main objectives of the current EU Environment Framework Programme. Overall reduction in the quantity and volume of disposed wastes, elimination of dangerous species within the waste streams and wastes recycling comprise specific targets of this policy. Within this framework a Greek funded research project entitled ?Development of an Integrated Alternative System for the Environmentally compatible Management of Used Batteries and Accumulators - DIASBAT?, was recently completed by a research team consisting of major Greek Battery producers and retailers, Research Organisations, Universities and Environmental Consultants. The aim of the project was the development of an Efficient Alternative Management System for spent portable Batteries and Accumulators, (B&A), in compliance with the prevailing EU and national environmental legislation, taking advantage of the state-of the art technology. The present article summarises the research carried out within the DIASBAT project in order to review and develop a set of sustainability indicators for the assessment of the effectiveness of Spent Portable Batteries Management Systems (SPBMS). Based on the European experience and practice, various indicators were initially examined regarding the performance evaluation of SPBMS. Specifically, the indicators used in European studies conducted to assess the environmental, social and economic impacts of the recently issued Batteries Directive 2006/66/EC, as well as the indicators used by European Collection and Recycling Organisations (CROs) to assess the performance of SBPMS across Europe were presented and analyzed. Additionally, the set of indicators used within DIASBAT to assess the effectiveness of alternative Spent Portable Batteries Collection Schemes developed within the project, are presented. The experimental collection networks of the DIASBAT project included schools, selected retail stores and a pilot network set up by the Greek Institute of Geology and Mineral Exploration (IGME). From the evaluation of the various indicators, it was deduced that in order to assess an Integrated Spent Portable Batteries Alternative Management System, a multi criteria analysis approach is required. Within the general principles of sustainable development, there is a need for different qualitative and quantitative indicators to be combined, taking into consideration critical parameters such as: annual portable batteries collection rates, compliance with the targets set up by the prevailing European and national legislation, economic performance of the System - and finally social criteria - environmental sensitization according to age, gender, economic prosperity, educational level etc.

Jan 1, 2007

By Alfred Petrick, Roger Dewey

INTRODUCTION Estimation of capital and operating costs for mines and mills has long been a necessary ingredient of feasibility studies, and though many practitioners have successfully used "rules of thumb" and factor estimating methods for many years, a great deal of work is usually required to prepare an initial estimate and/or to update or revise such an estimate. Development of comprehensive mining and milling cost models during the 1970's by the U.S. Bureau of Mines and by Canadian workers (O'Hara and Mullar) provided the basis for feasibility-level cost estimates, but the numerous equations and the apparent rigor and complexity involved in preparing a project estimate using these models has discouraged many, if not most, potential users. Their acceptance was also hindered by a broad misunderstanding by many engineers in the minerals industries who had little exposure to such procedures, and by a possibly inadequate level of explanation or documentation of the parametric approach to cost estimating. The preliminary nature of most databases, geologic/engineering/ and market, available to the engineer or analyst during the early stages of a mineral project is a universal problem. Basing corporate mega-investment decisions or even individual equipment selection decisions on the usual "SWAG’s has always been a risky practice, but in the current business environment, the "guesstimates" are almost 'verboten', and are certainly becoming antiquated with the advent of both the described models, the ubiquitous microcomputer, and the nearly-ubiquitous hybrid species known as the "computerized engineer". Engineers have almost always sought techniques of cost estimation that can be applied and justified when geologic and engineering information for a mining project is preliminary and incomplete. The answer, in some cases, is the "parametric" approach. Equations, based on actual, past experience are developed to relate capital and operating costs to major physical variables such as the rate of mining or milling, with modifiers for such details as mining method, process characteristics, methods of construction, or types of equipment . Cost Engineering Standards Five major types of fixed capital cost estimates have been defined by the American Association of Cost Engineers : 1. Order-of-Magnitude estimate based on previous cost data and minimal knowledge. usually a "ratio estimate" with no better than +/- 30% accuracy. 2. Factored or ratio estimate based on major equipment costs with probable accuracy in the 25 to 30% range. 3. Budget authorization or Preliminary estimate, based on sufficient project data to

Jan 1, 1987

By R. Dewey

WHAT IS AI? It's very hard to say. Most researchers and practitioners disagree with nearly any attempted definition, but most would agree that A1 does deal with the development of computer-related methods o f problem-solving. Artificial intelligence is a discipline which seeks to emulate human anatomy and/or thought processes by applying computer science, electronics, and mechanical engineering to the development of natural language processing, machine vision, robotics, and knowledge-based expert systems. Integration of these four fields will someday produce the robots of today's science fiction. A1 addresses problems of structuring large amounts of knowledge and representing relationships with rules and semantic frameworks rather than with mathematical equations. A1 is convergent rather than divergent - - conventional conputer applications use relatively small quantities of input to generate large output, but A1 generally reduces large amounts of information to establish a few major conclusions. The development of A1 has prompted greatly increased efforts on the part of scientists and engineers to understand just how humans think, organize information, approach problem-solving, and form conclusions. Some of the more exciting and possibly far-reaching advances in A1 are coming in this more-or-less soft-science area. Thirty years of A1 research (dating from a 1956 conference at Dartmouth College at which the term A1 was coined) has already spawned many widespread, almost ordinary, products: window graphics, hand-held controllers (mouse). function menus, etc., all in an attempt to make computers and people more compatible. WHAT IS AN ES? A1 can be used to develop EXPERT SYSTEMS, which are computer programs or systems which contain knowledge and rules by which problems can be solved. or at least by which possible solutions can be suggested for very complex problems. A1 can be used to better define problems so that solutions can be found. An ES is designed not to process numbers, but to process information according to rules and logic derived from actual practice and experience. WHY AI? WHY ES? Companies are increasingly aware of the value of accumulated knowledge and experience in designing, building, operating, and maintaining the increasingly complex or expensive physical plants in any business. As knowledge branches out and becomes more specialized, the accumulated learning of a veteran operator or manager or engineer becomes a scarce resource well worth preserving. EXPERT SYSTEMS offer a means of doing that, reinforcing, not replacing, human capabilities.

Jan 1, 1987

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. ng of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

Jan 1, 2008

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By William A. Vogely, DeVerle P. Harris

INTRODUCTION Perspective The phrase "minerala resource appraisal" is widely and loosely used to refer to any quantitative description of a naturally occurring source of fuels, metals, or nonmetals. This leads to confusion when mineral resources are so conceived, for the term refers generically to information on stocks-mineral endowment, resources, reserves, and potential supply-that differ in ways that are important in economic analysis. Mineral resource and other stock measures- these are not flows, e.g., the supply of minerals-have precise technical meanings, which are presented in this paper. Quotation marks are used to separate the nontechnical use of mineral resource from the technical. The term appraisal also leads to some con- fusion because it too is loosely used. When an appraisal employs probability and statistical methods, the appropriate term is estimationb, not appraisal or assessment. This paper presents a conceptual framework or mineral resource information which renders technical, or well defined, relationships of mineral endowment to physical attributes of the earth's crust and earth processes, as distinct from economic values, and identifies estimation approaches that lead to different economic measures of stocks and flows. An important result of this approach is the distinction between the relevance of mineral resource information to economic and policy issues about potential sup- ply (stocks) and dynamic supply (flows across time). With regard to policy analysis, this paper recognizes that mineral resource information has a cost as well as an imputed value. Such a treatment implies that there is an optimum state of resource ignorance, or enlightenment, for a given policy issue and that the relevant economic issue is the selection of that information strategy and appraisal methodology that is indicated by the optimum state. Until the initiation of the OPEC oil embargo, the demand for information on mineral re- sources and potential supply was limited to occasional studies commissioned by Congress or the President of the United States. In these, mineral and energy resources remained loosely de- scribed. When quantitative estimates were supplied, they were not rigorously made, and the estimates and the methodology accordingly escaped close scrutiny. Usually, neither the geo- logical nor economic bases for estimation were carefully described or critically examined. The imposition by OPEC nations of the embargo on oil caused a sudden change in the public and scientific demands for specific 'resource" appraisals, especially of oil and of uranium. These

Jan 1, 1985

By Jack A. Simon

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which difEerentia1 movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas are affected by relatively minor vertical movements of the shoreline. The large plates have continually or intermittently moved throughout the geologic past, resulting in various configurations of the continents and oceans, and coal-forming conditions have occurred at numerous times and places. Vast areas of our continents have been repeatedly inundated by shallow oceans and only relatively small parts of the present continents appear to have been above sea level throughout geologic time. Great forces acting principally along plate margins have folded and broken the crustal rocks, forming large belts of mountains.

Jan 1, 1981

By John C. Draper

The principal object of an underground coal mine transportation sys- tem is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Pace Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling at a longwall face, conveyors are convenient because of their low height, ruggedness, and ability to operate while being advanced. Similarly, in low seam heights, conveyor systems are easier and more economic to operate than the regular track haulage because roof has to be taken down for handling mine cars of adequate size.

Jan 1, 1981

By V. L. Magnus

The text of this chapter was not received in time for printing.

Jan 1, 1979

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold losses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead's common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992