Search Documents

By J. B. Mitchell

Comminution methods for base metal and precious metal ores have had considerable attention from mine operators, equipment suppliers and design engineers for many years and much of their work has been well reported. This interest derives from a healthy concern with the costs of comminution, often the largest single cost factor in ore dressing of hard ores. Many imaginative innovations have resulted. One notices a trend toward autogenous and semi-autogenous methods, combined with a trend toward very large equipment. Unfortunately, there has been less obvious cost incentive to experiment with softer ores. This is unfortunate because the consequences of inappropriate comminution methods can have an important effect on overall economics by influencing down stream processing and salability of final products. This paper concerns some of the factors to be considered in the selection of comminution methods for potash ores, and gives some specific examples to illustrate some of the principles involved.

Jan 1, 1969

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

By A. D. Davis, C. J. Webb, C. S. Johnson, J. L. Porter

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM) property. The mine produced primarily lead and zinc during the first half of the twentieth century. The BLM has expressed concern about acidic drainage as well as elevated arsenic levels in tailings and waste rock at the site. The mine site was evaluated for remediation in 1998 and 1999. Recent reclamation and remediation work included substantial regrading of waste rock, removal of material where metal loading were of concern, and re-routing of drainage from an adit. Trenching at the site shoed a greater volume than originally calculated during site characterization. Material was removed to a repository that was constructed at a nearby drainage divide. Because of physical hazards, the BLM has decided to remove some historic structures. However, a search of mine records and an inventory of archival materials were complete to preserve the history of the site.

Jan 1, 2002

By Richard E. Barrett

The relationship between coal characteristics and power plant performance has become a matter of increasing interest to utilities. This relationship can affect the value of coals, decisions as to coal washing, setting penalties for delivery of coal that fails to meet specifications, and justifying buying better coals (at higher costs) before public utility commissions. The study described in this paper was directed to identifying how coal characteristics impact on boilers and related coal and gas handling systems. TVA data for the period 1962-1980 was the basis for the study. Models were developed for boiler efficiency, boiler availability, and maintenance costs as a function of such coal characteristics as ash, sulfur, and moisture content and boiler age. Boiler load and maintenance efforts were considered as variables in some of the models, but were found not to be statistically significant. Although the results of this study are strictly applicable to only the TVA system, they can serve as guides or first approximations for other utilities.

Jan 1, 1983

By Warren C. Gerler

An overland belt conveyor system is installed for only one reason to save money. It must pay its way on a ton-mile basis over a stated period of time, and do so in competition with other forms of transportation. Such a system with its economies has recently been installed at Simco-Peabody's mine near Coshocton, Ohio by Link-Belt Company. Three miles in length, this system carries coal from open pit and underground mining facilities to the Conesville Power Plant of Columbus & Southern Ohio Electric Company. The coal was formerly trucked from the mine direct to the power plant; but over the years the mining operations have moved progressively farther and farther from the plant, making the over-the-road hauling distance correspondingly greater. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. The majority of the coal is recovered by conventional strip mining. Some underground mining` is performed by the high wall method.

Jan 1, 1963

By Robert J. Neubauer

I was asked here today to discuss the first long-term freight rate contract ever signed by a U.S. railroad and shipper. That was ICG's contract with the hoosier energy company to haul coal from southern Illinois to an Indiana power plant. I?ll also talk about why you can expect to see more such contracts in the future But first, let me tell you a little bit about the Illinois central gulf railroad and why coal contracts are so important to us. ICG is a principal mid-American freight carrier. We are one of the ten largest railroads in the united states and one of the ten largest coal-hauling railroads. ICG links the industrial great lakes region with the warm weather ports of the gulf coast. Some of the major points on our route map are Chicago; Indianapolis; Omaha; Kansas City; Memphis; St. Louis; and, of course, baton rouge and new Orleans.

Jan 1, 1981

The 21st Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Sheraton Tucson Hotel in Tucson, AZ on Saturday, Dec. 6, 2003. This year’s inductee, guest of honor and featured speaker at the banquet will be Thomas J. O’Neil, recently retired president and chief operating officer of Cleveland Cliffs Mining. Prior to Cliffs, O’Neil spent 10 years with Cyprus Minerals. He was also professor and head of the Department of Mining and Geological Engineering at the University of Arizona. As representatives of mining heritage, the Hall of Fame will induct James Boyd and Thomas F. Walsh. Walsh discovered a rich gold telluride vein in Ouray, CO, which became the Camp Bird gold mine. Boyd was a former director of the U.S. Bureau of Mines, vice president of Kennecott Copper and later president of Copper Range.

Jan 1, 2003

By A. L. Wilder

Coeur d'Alene Mines Corporation's newest precious metals property is located in the old Rochester Mining District approximately twenty-five miles northeast of Lovelock, Nevada. Built at an elevation in excess of 6 000 feet, the Coeur-Rochester gold silver heap leach property encountered cold weather operational problems typical of most northern Nevada heap leach properties, soon after the start-up of operations last fall. Due to the size of the heap area under leach at Rochester, it was decided that 1 the usual practice of spraying to an "ice field" and waiting for the spring thaw was impractical. Further, the delivery schedule for a solution heating system of the size required was unacceptable. Accordingly, Rochester personnel embarked on a program to seek out a leach solution distribution system that would enable an operation through the winter and yet be cost effective. The findings of this program were rather dramatic and, as a result, the whole perception of heap leach solution application at Rochester has changed forever.

Jan 1, 1988

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

By Steve Kral

Most innovations in the mining and processing industries have come from the need to produce more for less. Extracting minerals from the ground is expensive. And it is a constant struggle for mine operators to maintain the line between profitability and loss. The same holds for equipment suppliers. To maintain competitiveness, mining equipment manufacturers are building their machines with an eye to what the customer needs. Equipment makers know that if they do not supply machines that are productive and cost efficient, their competitors will. The result has been that the mining industry can now produce more ore with fewer people and more productive equipment. But, for all of the advances made in equipment, mine operators still demand machines that produce even more, are safer for workers and the environment, require less maintenance and can do the job at lower costs. And equipment manufacturers keep responding with larger, smarter and more technologically advanced machines.

Jan 1, 2005

Atlas Copco Wagner launched its ST1010 Scooptram load haul dumper. The ST1010 replaces the company’s Wagner ST-1000 Scooptram. The improvements to the Wagner ST1010 include increased reliability, ease of maintenance and driver comfort or ergonomics. The ST1010 has been redesigned and has added several new features and options not offered in the earlier model. These include anew boom design with side stops. Heavy reinforcements to the bogie offer better protection against the harsh working conditions in underground mining and tunneling. An auto lube system has also been added as has paint-on grip tread to reduce slips and falls during maintenance checks or repair work. Other features include a heavy-duty, auxiliary-fan motor, an isolated transverter, remote diagnostic pressure taps, a bolt-on battery box, raised air-intake, improved fuel-filter access for easier maintenance, larger wear-bars around the engine tub, and smaller, higher output batteries

Jan 1, 2000

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By V. T. McLemore

The Wind Mountain (WM) nepheline syenite deposit is part of the alkalic complex in the Cornudas Mountains, which ranges in age from 34.6 ± 1.5 Ma to 36.8 ± 0.6 Ma. The WM deposit consists of a complex, zoned pluton that ranges from syenite porphyry to nepheline syenite porphyry. The WM deposit has potential use for ceramics and dark-colored beverage containers and consists of nepheline, k-feldspar, albite, and varying amounts of other minerals. Analcime also is present locally but must be avoided because it is unsuitable for ceramic and glass. Chemically the deposit consists of 56-63 % SiO2 17-21 % Al2O3 and 4.0-5 % Fe2O3. Although initially iron is high, when the crushed rock is passed through a specialized magnetic separator, the iron content drops to below commercial maximum standards of less than 0.5% Fe2O3. The WM deposit is currently under exploration and testing to determine marketability.

Jan 1, 1994

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for all concerned people. The coal industry has taken great measures to reduce both types of pollution. Through the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. In many cases, the complete elimination of thermal drying by using centrifugal dryers to dewater fine coal products and meet customer specifications has completely eliminated air pollution from this source. To help eliminate stream pollution and the hazards created by tailing ponds, the coal industry is using centrifugal dewatering equipment. Use of centrifugals to dewater fine refuse for disposal would eliminate refuse ponds or extend their life. In doing this effectively and economically, preparation plants have the option of recycling the clarified water to close the water circuit or of discharging the water into receiving streams with the assurance that it contains an acceptable amount of refuse solids.

Jan 1, 1974

By Dennis Ofiara, Michael Lewis

An experimental 1.75 meter Shaft Boring Machine was designed and manufactured by The Robbins Company. The drill was used by contractor Drillcon Raise AB to drill test shafts at an SKB underground test facility. SKB is the Swedish authority responsible for safe management of nuclear waste materials. This “SBM1.8” Shaft Boring Machine was used to drill shallow test shafts ingranitic rock at SKB’s Aspo underground laboratory. The drill used a unique vacuum mucking system. The bored shafts were held to very strict tolerances for bore diameter, straightness, and verticality. This drill was launched and operated from a mobile launcher. Headroom and working space were limited. The SBM1.8 drill produced acceptable test holes. SKB will carry out several studies to determine the suitability of this geology, and of this technique, for safe nuclear disposal. In addition to future use at SKB, many applications are foreseen, particularly in the civil construction industry.

Jan 1, 2005

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009