Search Documents

By A. G. Sciulli, G. P. Ballock, G. Hearnshaw, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water

Jan 1, 1987

By David Logan, Sigurdur Finnsson

This project, which is intended to provide effective sewerage services to the Blue Mountains community, is located in the Blue Mountains National Park, about 60 km west of Sydney, Australia. The sewerage scheme consists of about 40 km of tunnels, out of which approximately 22 km have been completed. This paper describes the last major tunnelling operation on this project, the Hazelbrook to Katoomba tunnels. These tunnels, which mainly traverse the Hawkesbury Sandstone formation, are being excavated by a new 3.4 meter diameter Jarva Mk12C TBM. The mucking system consists of a continuous conveyor, which has allowed for some very impressive advance rates. The paper will consist of three main sections; the general geological conditions expected along the tunnel will be described in the first section. The second section will discuss the design and main features of the TBM, back-up system and continuous conveyor. The third section of the paper will describe the operational aspects and various performance data of the machine.

Jan 1, 1995

By Jean Dupéré

Introduction Before examining the current position of the asbestos industry and its market outlook, it is important to describe the product itself. If we are to understand the problems besetting this basic mining and manufacturing industry, and, more importantly, if we are to appreciate solutions to these problems, we had better view asbestos from the proper perspective. Asbestos has a unique combination of properties - properties not found in any other natural substance or man-made material. As a result, asbestos has found its way - in fact, is welcomed - into hundreds of applications. Properties and Products World production capacity of asbestos fiber is about 6.5 Mt (7.2 million st). Major producers and their approximate percentage share of actual production are: USSR, 47%; Canada, 24%; South Africa, 5%; Zimbabwe, 5%; Brazil, 4%; Italy, 3%; and others (including the US, China, and Greece), 12%. Although Canada accounts for less than one-third of the world's

Jan 7, 1984

By C. H. Bucknam

A suite of ore and waste rock materials was selected for the interlaboratory testing of combustion-infrared ("Leco") methods used to estimate carbonate and sulfide minerals present in test materials. The objective of the study is to develop ASTM standard methods to be used for metallurgical characterization of ore, acid drainage prediction for ore and waste during ore body evaluation, and for ore and waste control during the active mining of ore deposits. The results may be interpreted for classification of the materials according to their carbonate-sulfide or acid-base characteristics based on net carbonate value (NCV). The test materials were processed by x-ray diffraction and x-ray fluorescence (XRD-XRF) at Newmont Metallurgical Services (NMS) to obtain a semiquantitative mineralogical composition. Results of the interlaboratory testing for total carbon-sulfur, pyrolysis loss carbon-sulfur and hydrochloric acid residual carbon¬sulfur are compared with the mineralogical composition to aid in interpretation of the NCV classifications of the samples.

Jan 1, 2002

By Anthony G. Fonseca

About 45% to 50% of the coal mined in the United States passes through coal preparation plants. East of the Mississippi River, this number increases to about 75% to 80%. Although the cost for coal preparation is worthwhile to some, the coal industry faces the challenges of continuing downward pressure on the price of coal and the impact of new environmental regulations. Coal preparation is an effective process that achieves 75% to 80% ash reduction, 15% to 80% trace element reduction and 85% to 90% Btu recovery. It is less effective for pyrite reduction (35% to 70%) and on-line operating time (40% to 60%). It also suffers from obsolete control systems. In coal preparation, raw coal is modified to a more preferred form to enable its use. The methods used to achieve this modification must be cost-effective and appropriate to the raw coal, the scale of production and the end-user requirements.

Jan 1, 1995

By Robert M. Cox

The principal factor that must be determined for the effective design of a coal mine roof bolt support system is the maximum stable tension that can be developed with a given bolt assembly in a particular roof rock. There are four basic types of roof bolt anchorage techniques available: (I) the splitwedge; (2) mechanical expansion units; (3) resin point anchors or grouted expansion units; and (4) the cone shell which is placed in a reamed hole. A study of this problem has been made which includes theoretical analyses, laboratory experiments and field tests. A static free-body analysis of each of the anchorage techniques has provided formulas for predicting the anchorage capacity for a particular rock from the results of standard pull tests. The formulas also provide an insight into the anchorage mechanism of technique and allow for a comparative evaluation of the methods for design purposes. The theoretical analyses also indicate clearly the pertinent variables affecting the anchorage mechanism of each method.

Jan 1, 1977

By B. Das, D. D. Mishra, M. I. Ansari

Experiments conducted with a 75-mm-diem hydroryclone have shown it is possible to obtain an iron ore concentrate containing 60% Fe. 2.65% SiO2, and 4.0% Al2O3 from Barsua iron-ore washing-plant slimes. About 60% of the iron values are recovered from slimes containing approximately 49% Fe, 8.9% A1203 and 11% SiO2. The obtained products can be used in the sinter feed for iron and steel making. The key to achieving process success lies in establishing the correct cut point (d50) of the hydrocyclone through the manipulation of operating and design variables, such as spigot and vortex finder diameter, solids concentration and operating pressure. The cyclone efficiency is represented by the partition curve. The cyclone performance, evaluated mathematically from the reduced efficiency curve, is represented by the equation Y = 100[1 -exp(-axb)], where: •X = did 50, •Y = corrected of efficiency (%) and •a and b are constants.

Jan 1, 1994

By L. Landryova

The Department of Control Systems and Instrumentation, VSB - the Technical University Ostrava, has been involved in a project dealing with utilization of landfill gases, when the methane gas utilization and minimization of its release into the atmosphere was the main concern. The landfill site is generally a place, where technology for energy production can be built. The conditions for this technology implementation vary and depend on various factors. This paper is presenting findings and experience gained regarding a method of methane gas utilization for energy production. This method is concerning building bioreactors at the landfill sites, which are already operated. Every bioreactor can be thought of as a process, which is controlled in order to maximize energy production and minimize the methane gas escape into the atmosphere. The bioreactor landfill can represent a number of environmental and cost savings and, at the same time, is able to comply with all legislative issues.

Jan 1, 2005

By Pierre M. Gy

The final purpose of exploration is to esti- mate the grade and tonnage of the various qualities of ore contained in a given mineral deposit. This estimation cannot be directly carried out on the whole of the ore body. It usually requires four steps: Core Drilling Campaign The ore body is represented by a series of cores further divided into core sections of equal or unequal length. Core Splitting The core sections are longitudinally split into two halves: the first half is kept for various examinations and physical measurements, and stored for further reference; the second half (core sample) is used for determination of the chemical analysis. Core Sample Reduction The chemical analysis cannot be directly per- formed on the core samples. It requires the constitution of assay portions usually weighing from a few decigrams to one gram (more in precious metals assaying) and passing through a 100 or 150 mesh screen.

Jan 1, 1979

By Thomas H. Koenning, William E. Bruce

Determination of the state of a mine fire is an important function during firefighting and during rescue and recovery operations. It is imperative that an accurate, up-to-date assessment of fire conditions be available for persons directing such activities in order to avoid unacceptable risk to mine rescue teas and/or fire fighters. Many indicators which consist of ratios of the concentrations of fire gases have been developed over the years for determining the state of a mine fire. Results from numerous gas sample analyses are necessary for determining the trend of the fire. Some indicators are preferred because the influence of sample dilution, a frequent problem, is said to be eliminated. Definitions and examples of indicator6 found to be useful in diagnosing recent western U. S. coal mine fires are presented. Mine gas explosibility is an important subject also requiring rapid assessment. Example explosibility calculations are presented applying one widely used method. Establishing limits for withdrawal of personnel are discussed.

Jan 1, 1987

By J. B. Pautler, A. E. Gross, M. G. Strominger

The U.S. Bureau of Mines research on the use of cement as an agglomeration aid allowed precious metals heap leaching to become an economically viable method of precious metal recovery during the 1980's. However, many agglomerated ore bodies still exhibited poor heap/agglomerate strength. Precious metal recovery was often too slow or required prohibitively high levels of cement to be economically sound. Problems with heap ponding, blinding, and solution channeling and "wash-out" indicated that there was a need within the industry to improve on existing agglomeration technology. An in-depth research effort was undertaken to satisfy this need. Three years of research led to a patent on the use of vinyl addition polymers as effective agglomeration aids. A close working relationship between Brewer Gold and Nalco Chemical Company aided in the development of this program. This paper details the pilot test work, the full-scale evaluation at Brewer Gold Company, and conclusions.

Jan 1, 1990

By S. K. Kawatra, T. C. Eisle

In froth flotation of phosphate, it is important that the flotation be as selective as possible in order to maximize grade and recovery without adding additional stages of flotation. Flotation columns provide a means for improving the selectivity compared to conventional flotation machines and are of considerable interest for phosphate processing. The selectivity of a flotation column is largely limited by the degree of back mixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. The horizontally baffled flotation column was therefore developed to minimize back mixing and short-circuiting without introducing problems with plugging or reduced capacity. The introduction of horizontal baffles to a column reduces both entrainment of feed water into the froth and short-circuiting of feed to the tailings, which improves the column selectivity. The results of horizontally baffled column flotation of phosphate are presented for fatty acid flotation of phosphate, with comparison to conventional flotation using the same reagents.

Jan 1, 1999

By Klados. T.

MSC.Software assessed the performance of the drive end and non-drive end bearings on a ball mill using the finite element method. The assessment included the effect of mill and pedestal deformation on the performance of the bearings. Oil film thickness, oil pressure distribution and power requirement were of interest. A solution approach coupling a structural solver to a Reynolds equation solver was specifically developed for the project. Results showed that the deformation of the bearing surfaces had a significant influence on the performance of the bearings. For example, for the non-drive end bearing, the minimum oil film thickness computed for the deformable bearing surfaces was significantly lower than calculated for the non-deformable case. The results also showed that cavitation was likely in both the drive end and non-drive end bearings (severe negative pressures were obtained in both bearings). Other design variations were also assessed, e.g. a case with a modified radial clearance which improved the results.

Jan 1, 2006

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By Dan G. Wasyluk, Meryl J. Klassen, Tony J. Morris, Clive H. MacKay

The Rogers Pass Project in British Columbia has involved the construction of two railway tunnels totalling 16.6 km and a 345 m deep shaft. Systematic geological mapping was carried out at four headings during construction. The paper discusses the procedures used to record the geology, structure, rock mass characteristics and excavation performance. Coded data from the geological mapping and shift inspector reports was entered into a computer data base. The rock mass quality was evaluated for both the Geomechanics and Q classification systems. Continuous computer generated graphic logs were produced showing the excavated perimeter map, geological parameters, installed support and construction activities. The tunnel logs were updated on daily basis and used during construction by project staff for evaluating support requirements and monitoring excavation progress. The specific requirements, difficulties and advantages in mapping tunnels using a computer based system are compared to those of a conventionally mapped tunnel excavation with hand drafted tunnel logs.

Jan 1, 1987

By R. Hogg, T. F. Dumm

A simple shape description scheme has been developed which has the specific aim of distinguishing between angular and more rounded particles. The procedure involves fitting a general polygon (usually about 20 sided) to the particle profile. Geometric shape descriptors have been defined based on variations in the angles between adjacent sides and their radial displacement from the particle centroid. A two-parameter shape description, incorporating an angular variabli1ity and an elongation index, has been shown to be clearly consistent with visual observations. A single-parameter angularity index has been shown to be very sensitive to small differences in particle roundness and seems to provide a better description of angularity than other approaches such as signature and fractal analyses. The scheme has been applied to three sets of fine quartz particles produced by different grinding procedures. The results indicate that the technique is capable of distinguishing between angular and re1atively rounded particles and can quantify their specific shape features.

Jan 1, 1991

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995

By P. R. Khangaonkar, G. Bhaskar Raju

Three types of flotation columns were developed with a column dia of 8.0 cm and a length of 160 cm. The first type consists of an ordinary column fitted with a porous plate at the bottom. The second type consists of two electrodes at the bottom to obtain very fine and uniform bubbles generated electrolytically and the third is a combination of first and second types, i.e. to get both electrolytic bubbles and air from the compressor through porous plate. Three different ores were tested-gold tailings for recovery of scheelite, copper tailings (chalcopyrite) and oxide copper ore. In the case of scheelite and copper oxides, good results were obtained with the first type of column itself, whereas the third type column was found fairly effective in the recovery of chalcopyrite. The variables like the effect of reagent concentration, column height above the feed point, feed flow rate, current density, air flow rate, particle size etc. were examined.

Jan 1, 1988

By E. D. Dainty, B. E. Enga, D. L. McKinnon

Following considerable laboratory studies concerning particulate control systems for underground use, a program was commenced to develop practical real life implementation systems. This program covers the implementation in seven mines of particulate filter systems to 10 engine models from three engine manufacturers in 12 different vehicle types, a total of 24 vehicles. As the program ran, one mine had to drop out and a mutually agreed upon system could not be arrived at for another. Hence, the program included five Canadian mining companies. Several of the vehicles trialed at Brunswick Mining were trialed by Brunswick themselves. Nonetheless, the data is presented. This paper covers the work performed from the beginning to the end of the demonstration program. Data collected to properly select and design filter systems along with technical conclusions of the demonstration are presented. Also presented are the results of a survey that highlights the participating mines' acceptance of the technology.

Jan 1, 1991

By E. Topuz, J. Mastoris

The problem of defining the optimum final limits of an open-pit mine has challenged the mining industry for the last three decades. The difficulty results mainly from the great number of variables involved and from the sheer computational effort required in real-life applications. An actual lignite deposit is used in this study to introduce and apply a new methodology that can be used as a basis for surface-mine design optimization. A geologic-reserves model of the deposit is first developed with the use of an integrated geostatistical-modeling package. The model is transformed into an economic one through the use of flexible objective function formulation(s). The final open-pit limits are then optimized using a competent commercial optimizer, and comparative-sensitivity analyses are performed to study the effect of some basic mining and economic parameters on the optimal pit design. The conclusions drawn can develop useful guidelines for decision making by the mine operator.

Jan 1, 1996