Search Documents

By C. Babbitt, J. O’Green, N. I. Jayaraman

In many mines, dust-laden air from an entry being driven by a continuous miner will contaminate the intake air to the roof bolter operator and other downwind personnel. Through a US Bureau of Mines (USBM) contract, Foster-Miller Inc. has evaluated several control techniques to reduce the respirable dust exposures of downwind personnel. One fan and tubing technique consisted of bypassing the miner-generated dust directly to the section return. The results of the evaluation of this technique revealed that reductions in dust concentrations of 90% or more can be achieved at downwind roof bolter locations. A second method was to clean the dusty air from the upwind continuous miner by using a dust collector. The cleaned air was then supplied to the bolter through collapsible tubing. An underground evaluation showed reductions of 82% to 96% when the dust collector was operating. A third method was to reduce the quantity of dust contributed by the miner to the return airstream. A water-powered scrubber was installed over the throat area of the continuous miner. More than 1.18 m3/s (2500 cfm) of dusty air moved through five tubes with dust collection efficiency exceeding 75%. Underground evaluation results showed that return dust concentrations were reduced by about 60%. This paper discusses the ventilation and dust control techniques used for personnel downwind of the continuous miner.

Jan 1, 1987

By S. W. Kan, M. G. Kakarkis, J. Zelanco

Grouting has been used in underground mining for more than 20 years. Chemical grouting is often used as a remedial measure when the implemented ground-control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. The utilization of polyurethane grout is restricted by its limited range of physical and mechanical properties. To overcome some of the drawbacks of polyurethane, research is being conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as Strata Grip, provides a number of features, including variable gel times and a much-reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted The assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1999

By Satya Harpalani

An investigation was carried out to study the microscopic structure of coal in order to understand the phenomenon of methane migration. A Scanning Electron Microscope (SEH) was used to study the surface and pore structure of bituminous coal taken from an underground mine. Micrographs obtained showed the highly porous nature of coal which explains the large quantities of gases that remain within the pores in the compressed and adsorbed forms. These micrographs further showed that most of the pores within the coal matrix are the 'dead-end' type and do not contribute much towards the flow of gas. The most important finding was that solid coal has a network of cracks and fractures indicating that it is these cracks that are primarily responsible for the gas flow, rather than the pores. The size and distribution of the pores within coal influence the capacity of coal to retain methane but movement of the gas molecules is the responsibility of the microfractures. Any mathematical modeling to simulate gas flow through coal must take this into account. For purposes of modeling, the structure of coal can be considered to have dual porosity. First, the gas molecules are released from the pores and there is a gradual migration towards the fractures. Once the gas reaches the fractures, its movement is eased greatly along these fractures.

Jan 1, 1987

By M. Misra, I. Anazia

The dispersion of oily collector has a significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. Such dispersion and reagent addition techniques are invariably inadequate and nonselective. A new collector addition technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This technique involves atomization of the collector into the air stream. Under these circumstances, an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the air phase (continuous with respect to oil), and the air phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and, most significantly, increases the flotation rate of ultrafine coal. Atomization of collector/frother combinations yielded improved flotation recovery and maintained near uniform froth levels, which is a desirable feature in coal flotation. Microscopic examinations of the attachment of oil- coated bubbles at a coal surface were conducted by attachment time and contact angle measurements. Oil-coated bubbles attach at significantly faster rates and with a higher contact angle than oil-free bubbles.

Jan 1, 1988

By S. I. Nozhko, V. N. Guliy, A. A. Zolotarev, L. M. Luyshnia

The study of the apatite deposits of the Aldan Shield shows wide spread of the Precambrian apatite-carbonate ores and possibilities of using them for extraction of apatite. Dependency of flotation on ore minerals was studied according to the following scheme: preparation of the monomineralic samples of anhydrite, gypsum, chlorite, serpentine, phlogopite, apatite; mixing them in apatite ore of the average composition; followed by flotation. Another series of the experiments was conducted to ascertain a dependence of flotation activity of the different minerals on the different flotation reagents, which were used as collectors. It has been shown that apatite from silicate-carbonate ores is most extractable because it has the biggest size of grains and is the most free of inclusions. Beneficiation of the sulphate-containing apatite-carbonate rocks is possible when flotol - 7.9 is used as a collector. Meanwhile, the use of the tallaktam leads to an increase in the sulphate recovery. The estimation of individual technological features of the layered Mghydrosilicates and their influence on the process of beneficiation has been examined using samples of apatite-dolomite ore (P205-8%) with the addition of the phlogopite, serpentine and chlorite. The results show that there is little influence of the chlorite presence on the flotation while the serpentine presence leads to a decrease of the flotation, because of its high specific surface area.

Jan 1, 1993

By Guiseppe Bonifazi

This work applies the definition of "separation function" already introduced in the paper presented at the XVIII IMPC. This 'function" (defined for a certain size distribution after comminution of an ore) refers to the recovery distribution of a mineralogical species in a product made up of all the particles having at least a given content of that species. Many tests would be required to determine the liberation function for each mineralogical species, particularly for complex ores. Several stages of comminution would need to be examined and the mineralogical composition of the particles of each grain size class would need to be analyzed for each process step. A quick and dirty method is shown for obtaining the "separation function". It is based on the processing of data from topological maps of polished and/or thin representative sections of ore. By superimposing grids of different sizes over these maps and with appropriate combinations of mesh sizes, it is possible to simulate the grain size distributions linked to different stages of comminution and then evaluate the mineralogical composition of each grain. The procedure is carried out full automatically and can simulate a complete treatment circuit, imposing cut-off grades for the products at each separation phase. It is also possible to predict the results of treatment processes that involve grinding phases. The procedure has been successfully applied to complex ores containing several useful components.

Jan 1, 1995

By John R. Thalimer

For the past four years the U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors. Data modeling techniques based on values calculated from a motor's voltage and current phasors were used to produce a pair of polynomial equations that calculate a motor's insulation leakage current and power. This paper describes a prototype system using these models that monitors six motors on a continuous miner for insulation leakage in order to anticipate insulation failure. The system consists of a motor-data system for each motor on the machine, a control computer located some ' distance from the miner, and a serial bus to interconnect these items. Each motor-data system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the serial bus. The control computer can request and receive phasor data from any motor-data system on the bus. Using models developed at the Bureau, the control computer calculates and displays two deterioration values for each motor, one for leakage current and the other for leakage power. These values are then stored into a database from which the user can display them over time.

Jan 1, 1992

By Ching L. Wu, Bolek Chytrowski, Peter Frobenius, Dale Roberts

During the past few years, the first stage of the Waste Isolation Pilot Plant, (WIPP) which consists of an exploratory shaft, a ventilation shaft, shaft stations, access drifts and test rooms, has been under construction. Construction of the first stage is scheduled to be completed in the summer of 1983. The U.S. Department of Energy (DOE) is constructing the WIPP facility to demonstrate the feasibility of disposing of defense-related nuclear waste in the bedded salt deposits of the Delaware Basin near Carlsbad, N.M. The project promises to be a proving ground for underground nuclear waste storage facility design and construction. The completed underground plant will extend over an area of 647,500 m2 (160 acres), and 1,360,500 metric tons (1,500,000 tons) of salt will be excavated. The first stage of the project, the Site and Preliminary Design Validation (SPDV) Program, provides for full-scale construction of the major components of the underground facility. Shaft construction and underground development are described. Rock bolt installation is performed as required for roof control. Geotechnical instrumentation is installed to monitor the behavior of underground openings. Direct observation of the constructed shafts, shaft stations, and underground openings is expected to confirm the adequacy of the underground design and allow full-scale construction of the first U.S. underground nuclear waste storage facility to proceed.

Jan 1, 1983

By J. B. Gwiazda

S.S. Peng The highlights of this paper are: The shield supports with lemniscate links will exert a tangential force on the roof strata, causing unnecessary and harmful roof movements, thus damaging the roof structure. The principal source of the tangential force is the horizontal movement of the point O, the pivotal joint between the canopy and the caving shield. When the support height is changed during setting, the point O will move along a curve upward and rearward toward the gob. As a result, it produces a vertical movement, causing the roof to move up a distance of t d, and a horizontal movement toward the gob, creating vertical fractures in the roof. The major purpose for employing the lemniscate- link system is to protect the hydraulic legs against the action of the bending moments induced by the tangential force that causes deformation or destruction of the legs. Based on these two points, the author suggested that, in order to eliminate the harmful effects of the lemniscate-link system and strengthen its advantageous features, a shield support with a new design of that mechanism has been developed. With the new design, the conventional rigid lemniscate links are replaced by hydraulic rams. When the pressure inside the rams reaches a certain level, the ram will yield.

Jan 1, 1987

By Daryl R. Tweeton

The Bureau of Mines has developed PC-based tomographic computer programs for geophysical applications, and is making them available to potential users as part of a Bureau plan to facilitate the transfer of technology to industry. These programs were initially developed for predicting and monitoring the flow pattern of leach solution during in situ mining. Seismic crosshole tomography has located fractured zones of low seismic velocity and saturated zones of high seismic velocit above the natural water table. The Bureau has applied tomography also to assessing high-wall blast damage, and examining the integrity of mine-related geological structures. The tomographic programs include the straight ray pro ram BOMTOM (Bureau of Mines Tomography? and the program BOMCRATR (Bureau of Mines Curved Ray Tomographic Reconstruction) that can be run with either curved or straight rays. Both programs provide optional mathematical constraints to help counteract the nonuniqueness of reconstructions that occurs with crosshole data. They are available from the Bureau free of charge. With typical data sets, they can be run on a 386 microcomputer with 640 Kb RAM. BOMTOM was described in the Bureau Report of Investigations 9159, so this report emphasizes BOMCRATR. Curved and straight ray reconstructions using seismic field data collected while simulating injection of leach solution were compared. The curved and straight ray tomograms were quite similar even with velocity variations of more than 50 percent.

Jan 1, 1992

By Gilmore R. Tostengard

The advent of inexpensive computers has opened vast opportunities for improved planning and control of capital projects. The mining and mineral processing industries have welcomed the opportunity, and new and improved quantitative management techniques have abounded. This chapter will discuss commonly used computer applications for economic justification of the project, preparation of the cost estimate, planning the work schedule, monitoring work progress, and control of costs and productivity. Finally, there is a review of the degree to which the industry uses these applications. Our experience suggests that while we in the industry have been quick to adopt the new techniques, the quality of our input data has not always kept pace. During the next decade, our push should be toward improving the quality of the basic data and assumptions so that we can fully benefit from the sophisticated techniques. The GIGO (garbage in, garbage out) principle is a wellworn cliche, but it is especially valid here. One of the keys to getting good input is commitment. Unless the managers who are to use or benefit from the system are committed to it, the effort will fail. They must be com- mitted to the underlying principles of planning and control sufficiently to expend their time and resources on them; planning should be especially given emphasis. They can't be too busy to plan.

Jan 1, 1979

By Michael DiMatteo, Michael D. Gardner, Eric F. Perry, John K. Felbinger, Robert S. Evans

A hydrologically isolated surface coal mine was reclaimed using acid material handling, alkaline addition and ground-water management techniques. Eight pit floor drains were installed during reclamation to intercept ground-water flow in the mine backfill and minimize water table buildup. All drains began flowing within six months of installation. Water quality and ground-water discharge have been monitored for four years after mine closure. A thin water table aquifer about five to seven feet thick has developed in minespoil about 20 to 40 feet thick. Ground-water flow direction is largely controlled by geologic structure and the drains. Median ground- water discharge is about 0.43 gallons per acre per minute, and varies an order of magnitude between wet and dry seasons. About 19 % of precipitation enters the aquifer as recharge. Seven of the eight drains typically discharge net alkaline water. Alkalinity is produced continuously and concentrations are highest during dry periods. Conversely, sulfate and acidity concentrations increase during wet periods as slugs of accumulated acid products are leached. Overall water quality is controlled principally by minespoil geochemistry and added alkaline material. The drains have successfully directed ground-water to a planned discharge area. Without the drains, a ground-water mound was expected to form against a buried highwall and discharge over a large area.

Jan 1, 2000

By D. W. Park

Longwall mining is considered to be the most efficient underground coal-mining technique in terms of coal extraction ratio, production rate and safety standards. Due to the increasing demand for higher coal production, the recent trends have been to use wider panels and to maintain a faster face movement. For these reasons, longwall mining can result in unexpected roof falls, excessive face convergence, shield damage and numerous maintenance problems, which can cause sudden interruption of coal production as well as serious safety hazards. Recent work at the University of Alabama has been dedicated to the development of a longwall strata-control and maintenance system that can integrate real-time shield monitoring, data presentation, analysis, forecasting and warning modules. This integrated system has been called LoSCoMS. The main objective of the system is to provide minute-by-minute stability and maintenance information such as the following: high-load, low-setting pressure, leg leakage, etc.; the analysis of various mining and geological parameters to determine past and present roof characteristics; and the forecasting of loading patterns for the following mining cycles, the next periodic weighting, etc. By using this unique system, mine operations personnel are well aware of past, present and future roof-loading patterns at the longwall face and, thus, proper safety measures can be taken ahead of time.

Jan 1, 1999

By G. M. Wilemon, B. J. Scheiner

The Bureau of Mines conducted investigations on extracting phosphate values from fine-particle wastes generated during the mining and beneficiation of phosphate ore by leaching dried wastes using a H2SO4-methanol mixture. Although phosphatic clay waste contains up to a third of the phosphate originally present in the ore, recovery of these values represents a significant challenge due to the fine grain size of the material, the particles averaging less than one micrometer in diameter. Waste samples obtained from two Florida producers yielded phosphate extractions of 71 and 84 pct, respectively, when leached under ambient conditions and at a stoichiometric acid ratio of 1.4:l. Elevated temperatures did not improve the amount of phosphate extracted. Undesirable A12O3, Fe2O3, and PlgO impurities were largely rejected; higher grade wastes gave acids that meet established industry impurity standards and lower grade samples yielded acids that marginally fell short of the standard. Separation of the crude acids from the insoluble residues was accomplished via vacuum filtration through either filter paper or commercial filter cloths. Both filtration rates and solids retention were improved by the addition of 0.5 lb/ton of poly(viny1 acetate) (PVAc) or poly(ethy1ene oxide) (PEO) to the methanol-acid slurries. These results show potential for substantially increasing the reserves of an important domestic resource.

Jan 1, 1989

By J. Herbst, H. B. Treweek, V. R. Degner, G. Poling

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976

By S. G. Mougiakakou

A computerized system (SCAPEVIEWER) based on landscape indices and artificial intelligence techniques is proposed in order to classify landscape images into various categories according to the quality of the pictured scenery. Photographs (totally 108) from various landscapes have been clustered, from seven experts in accordance to the mean estimation of landscape quality, into distinctive (C1), typical or common (C2), and indistinctive (C3). For each of the landscape photographs, ten (10) environmental and operational indices have been selected and determined, corresponding to visibility (V), naturalness (N), relief (R), flora quantity (FC), flora quality (F), water (W), skyline (SL), visual entities (G), season (S), and viewer position (P). These landscape indices are fed to a classifier. The classifier is a feed forward Neural Network (NN) trained by a novel hybrid method combining genetic algorithms and the back-propagation algorithm with adaptive learning rate and momentum. A total classification rate of 93.5% has been achieved, using only 8 input neurons. The discarded input neurons correspond to the indices S, and P. The pilot system SCAPEVIEVER has shown the feasibility of landscape photograph classification into three categories (C1, C2, and C3) according to the landscape quality, selecting simultaneously the most robust indices, by means of a computerized system combining the knowledge of an expert with a NN based classifier.

Jan 1, 2003

By Elvin R. Beach, Jaroslaw Drelich

Pull-off forces were measured for 8-9 pm diameter polystyrene (PSI particles on smooth spin- coated polystyrene films and hexadecanethiol (HDT) self-assemble monolayer surfaces using atomic force microscopy (AFM). Three parameters were controlled during experimentation: (i) the maximum applied load pressing the particle onto the substrate was varied from 50 to 4,000 nN, (ii) loading/unloading rate for the particle to attach and separate from the substrate varied from 0.01 to 9.3 Hz, and (iii) contact time for particle to reside on the substrate surface before retracting the particle to separate it from the surface changed from I µsecond to 200 seconds. the pull-off forces increased with increasing applied loading, increasing loading/unloading rate, and increasing contact time for the PS particle on PS film and on HDT monolayer. The PS particles experience elastic and plastic deformations duringpull-08 force measurements. Plastic deformation is primarily associated with flattening of surface irregularities. The results obtained in this research suggest that the particle-substrate contact areas of the magnitude comparable to those predicted by the JKR contact mechanical model can be reached in the AFM experiments by using high applied loads and long particle-substrate contact times. This result re-opens the prospect of' using AFM for studying surface energies of deformable micro-particles, even if the micro-particles have small irregularities on the surface.

Jan 1, 2003

By Kathleen Y. Knoebel

This paper describes a graphical mini computer system called MPASS 2 (Mine Performance Analysis/Simulation) which has been designed to conduct analysis of underground room-and-pillar mining operations using both conventional and continuous mining methods. Dynamic, graphic displays of mine face machine activities are presented on the CRT screen to provide extensive visibility into underground mining activities. MPASS 2 consists of: an interactive inputting system that graphically creates a room-and-pillar mine and describes the mine when production is initiated; a time-step simulator that produces statistical summaries of shift activities and uses CRT screen graphics for accelerated-time display of machine activities and delays; a statistical analysis subsystem for analyzing mine performance data; an industrial engineering system that permits users to enter actual machine activity statistics and replay mine operations on the CRT screen; and a data management system to store historical performance information on mine characteristics and operations. MPASS 2 operates on a Hewlett-Packard 9845B mini computer with 450 K bytes of extended memory, and is written in H-P BASIC. It has been installed at Freeman-United Coal Mining Company in West Frankfort, Illinois and at the U. S. Department of Energy Pittsburgh Mining Technology Center. Applications include production system simulation, industrial engineering analysis, production scheduling, new equipment evaluations, and training.

Jan 1, 1982

By R. H. T. Garnett

Reserve estimation is a process that commences with sampling and culminates in the issuance of a reserve statement. The tin, gold and diamonds that occur as marine placers on the continental shelf are low grade with very erratic mineral distributions. Sampling, using a variety of special equipment, determines the extent and grade of the mineralization. The sample size is important, especially for diamonds. Together with the sampling density, it determines the accuracy of the grade estimate. Bulk sampling is a confirmatory process. The choice of mining equipment, either new or developed from onshore activities, dictates the unit costs, the cutoff grades and the selectivity of extraction. Thus, the size of the blocks that comprise the mining plan and the reserves are determined. A variety of estimation methods of different reliability are available, with the most sophisticated being kriging. Dilution and losses during mining must be taken into account in estimation, and a grade-volume curve should be constructed. Diamond deposit estimation also involves an extra variable, the dollar value of the stones. During and after mining, essential feedback on the accuracy of un estimation may be given by the RIE factor and by a mineral balance. Reserve estimates are required for several reasons and may be subject to public disclosure. The use of the correct definitions is, therefore, important.

Jan 1, 1999

By E. A. Rychkun

Introduction Minicomputers have been gaining acceptance in mining. Low cost interactive processing and plotting can now be controlled by geologists or engineers needing rapid solutions and specialized mining software in formats that allow noncomputer personnel to readily interact with computer processes. User-oriented programs maximize the use of interactive display features and graphics, as shown by the HP9845 minicomputer, a unit with portability, processing power, graphics capabilities, capacity, and peripherals such as plotters, digitizers, disk drives, and printers. Application Coal exploration projects require that much effort be spent determining coal volumes within trial pit limits. This determines a prospect's viability and potential. Adapting volume calculations to a computer has been limited, since it was difficult to create reasonable representations of complex coal seam geometry with a digital process. So many of the simple mechanical procedures needed to produce pit reserves are still performed manually by geologists and engineers. But with new minicomputers and their interactive graphics, it is now practical to accurately model complex structures without tedious calculations. GEOSEM (Geomin Seam Oriented Exploration System) is a computer system designed to analyze coal prospects. The system shows how a coal prospect, with complex geology, can be quickly analyzed, modeled, displayed, and evaluated for mineable reserves. Its interactive graphics allow rapid visual presentation of data, high-speed tabular reports, and precision plotting. The system is most effective when used by a geologist or engineer who selects the required operations and specifies relevant parameters via screen and keyboard interaction. Rolling Hills The Rolling Hills prospect represents a typical Rocky Mountain coal deposit. Enough geological interpretation has been done to show a complex system of block faulting with coal seams following synclines of stratified lithologies. With the completion of initial drill hole exploration, questions arose concerning coal volumes and strip ratios involved with various pit limits. Quality information had been gathered on the coal intercepts. It was decided that coal vol¬umes and pit designs were of prime importance. The objective was to enter and display data, create a computer model based on interpretation, develop pit designs, compute seam/ waste volumes, and report various contents. The project, begun by entering data in the GEOSEM system, was completed in several days. Data Entry For modeling, the prime information was seam identity and drill hole intercept. Other information-rock type, Btu rating, and percent of ash, sulfur, and moisture-was also available. It, too, was entered into the data base through the computer keyboard and then reported, verified, and corrected. Various reports can be produced, according to user specified sort parameters. For example, from an analysis of available data, only 14 intercepts could be found with Btu value greater than 8000 and sulfur content less than 0.4%. The sort option can also be used prior to entry into the analysis routines. Data Analysis Though the objective was to create a seam model and compute reserves, it became necessary to project quality information into unsampled areas. Statistical analysis was then war-ranted. A typical analysis correlated the lack of relationship between percentage of ash and Btu. Although histograms were also produced, these typified a lack of samples and "ragged" distributions. A geostatistical analysis was also applied, showing the results of computing a 2-D variogram on the largest coal seam. Results showed an average range of 18 m, with a poorly defined variogram. Data Display and Drafting Scaled plans and sections were required so seam locations could be compared to hand drawn interpretations and drill coordinates verified. At the same time, topography could be interpolated from collar elevations to determine whether surface control points were needed for better definition. In addition, a new set of 50 final-scale drawings were required, showing new drilling information. By using the computer screen as a "scratch pad" device, various sections were displayed and then plotted on a drum plotter at the desired scale for overlay on original sections. Both lithology and seam name were plotted for the five main sections. Since the coal seams were striking north-south, sec-

Jan 11, 1981