Search Documents

By M. J. Raffaldi, K. W. Harris, K. A. Perry

"Highwall miners have been widely used to extract additional coal reserves from existing surface operations, particularly on contour operations in the Appalachian coalfields. Using a continuous miner cutting head, coal may be extracted from significant depths (such as 150 m), leaving behind an array of web and barrier pillars with the purpose of maintaining highwall stability. This method inherently involves elevated risks to both equipment and personnel due to proximity to and increased exposure time near highwalls. As a result, modern operations should actively design web and barrier pillars to maximize extraction while providing adequate stability. The ARMPS-HWM software, an empirical-based program created for the design of web and barrier pillars at highwall mining operations, is one such approach. The calculated stability factor is compared with empirically established guidelines produced from examining case histories.The ARMPS-HWM program is a handy tool for initial design, but understanding the site’s structurally significant geologic features and geomechanical behavior is important and may potentially increase extraction. We created a two-dimensional numerical model using FLAC3D and calibrated it to ensure pillar strength, closely following the Mark- Bieniawski formula for a typical range of pillar geometries and overburden properties. The development of pillar stresses along a highwall panel was then numerically investigated as mining progressed, and the stress distribution between barrier pillars was found to be asymmetric, which can result in an over-design of the closeout web pillars if tributary area loading is assumed. Finally, the importance of adequate barrier pillar stability is highlighted."

Jan 1, 2014

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

By Ping Li, Baokun Zhou, Lei Yang, Changfeng Li, Erhui Zhang

A uniaxial compression experiment was conducted on standard sandstone specimens to explore the sandstone’s mutation characteristics and early warning interval during deformation and failure. Meanwhile, acoustic emission (AE) and digital image correlation (DIC) techniques were introduced to realize multi-field analysis and cross-validation from the stress field, deformation field, and elastic wave field. The mutation characteristics of rock failure were investigated based on the cusp catastrophe theory. The results showed four mutation points in the destabilization process of sandstone: compressional density, yielding, destruction, and residual retention. As an internal activity characteristic of the sandstone failure process, AE directly reflected the dynamic failure process of sandstone. The stress variation was closely related to the evolution of AE characteristics. Sandstone loading failure was a process of the mutations of releasable elastic strain energy, dissipative energy, and releasable elastic strain energy. The mutation of dissipative energy was used as the starting mark of the sandstone warning state, and the second mutation of releasable elastic strain energy was used as the end mark of the sandstone warning state. Besides, the warning range corresponded to the loading time of 178 to 208 s. Finally, the sandstone instability warning interval was re-determined from deformation field evolution characteristics in the sandstone damage process, with a loading time of 180–204 s. This was consistent with the warning interval specified using the cusp catastrophe theory. The combination of AE, DIC, and cusp catastrophe theory revealed the mutation characteristics and early warning interval of sandstone failure. Hence, the results provide significant importance to predicting rock failure.

Aug 23, 2023

By Zhe Wang, Tichang Sun, Yongqiang Zhao, Zhengyao Li

Coal-based reduction followed by magnetic separation is a promising technology for processing refractory iron ores. Analysis of the size distribution of metallic iron particles is an effective approach for exploring the mechanisms of coal-based reduction. As metallic iron particles exhibit very complex shapes compared with nature ores, approaches for measuring and characterising metallic iron particles still remain unclear. In this study, the size of metallic iron particles was measured and characterised using manual point-counting by optical microscopy technics and image analysis. The effects of CaF2 as an additive on behaviour of the particle size distribution (i.e. mean size and cumulative frequency distribution) were also determined. Results indicate that CaF2 had a significant effect on the growth of metallic iron particles. When the CaF2 dosage increased from 0 to 8%, the mean size according to the area method increased from 9.03 to 16.28 μm, while the promotion effect gradually weakened and generated many fine metallic iron particles when the CaF2 dosage exceeded 8%. An increase in CaF2 dosage also led to cumulative distribution curves gradually shifting to the right mainly because F− can break the crystal structure of each phase during the carbothermic reduction of titanomagnetite and reduce the stability of the lattice structure, thus reducing the melting point and accelerating the growth of metallic iron grains. Compared to different measuring methods, the area method is a more suitable approach for measuring and characterising the size of metallic iron particles.

Sep 18, 2020

By A. D. Paananen

With the demand for higher grade feed by the American steel industry and the depletion of the direct shipping ores from the Marquette Iron Range and elsewhere, there was a need to develop the low-grade orebodies. The large reserve of fine grained oxidized iron-formation at the Tilden Mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Preceding the present mining-concentration-pelletizing complex, about 6,500,000 long tons of direct shipping siliceous ore were shipped from the Tilden Mine. Following development of the concentrating and pelletizing flowsheets, engineering and construction was initiated to develop the mine and construct concentrating and pelletizing facilities to produce 4,000,000 LTPY of pellets from this low grade crude ore. Operations started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleveland-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling-Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Due to the non-magnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden orebody have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of des liming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions.

Jan 1, 1978

By Thomas J. DeMull

Heap leaching was introduced to the precious metals mining industry approximately two decades ago as a simple, low cost method for recovering gold and silver from ores. Since that time, operational experience has contributed to knowledge and understanding of the process, making it a reliable alternative to conventional milling processes for low grade ores. At time of this writing, dozens of heap leach operations are active producing hundreds of thousands of ounces of gold and millions of ounces of silver annually. These successes have caused the popular press to acclaim heap leaching "high-tech" gold mining, but, despite the hype, the process remains a simple one. An example of simplicity in heap leaching is the operation established in 1986 at Amax Gold's Sleeper Mine. Starting with a simple goal, namely to produce gold from sub-mill grade ore at low cost, heap leaching was rapidly implemented at Sleeper; only five months after testwork started, leaching commenced on the first commercial scale, 50,000 ton heap of low grade ore. Sized at 600,000 tons per year to produce 10,500 oz gold per year, the low grade heap operation has performed beyond expectations. During the first year of production, 881,800 tons have been leached producing 15,665 oz of gold and 35,528 oz of silver. Operating ·costs for the first year have averaged $112 per oz gold produced ( or $95 per oz if silver credit is included). Successful implementation of heap leaching at Sleeper has had a dramatic impact on ore reserves and future operations.

Jan 1, 1998

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp., and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the seconaary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1981

By G. E. S. Valadao, J. D. Miller, C. L. Lin

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake poremicro structure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 m, length of 500 m and height of 4000 m. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: 1) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method,2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4)some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By Tong Deng, Yun Ma

Gold-copper ores have become important gold resources (von Michaelis, 1989), but the gold extraction from such materials posed a challenge due to the detrimental effect of copper species on gold cyanidation. Ammoniacal cyanidation process was rec­ommended (Muir et al., 1989) and practiced (Castello et al., 1992) for gold extraction from the gold ores which contain cop­per at moderate level mostly in form of oxide. This paper pro­vides an example to apply the ammoniacal cyanidation process to processing such a copper bearing gold ore.

Jan 1, 1996

By Jim W. Rosteck, Anthony Del Vescovo

In December of 1992, the City of New York, Department of Environmental Protection, solicited bids for Contract 543B. The low bidder was a joint venture of Schiavone Construction Co., Inc. and the J. F. Shea Co., Inc. When completed, the project provides a 4.88 meter diameter water tunnel 8,840 meters long. This paper presents a case history of the equipment and construction methods utilized for this, the first portion of the New York City Water Tunnel constructed by use of a tunnel boring machine.

Jan 1, 1997

By Martin Oatman, Lawrence Lenahan

The West Seattle Tunnel is part of a regional sewer conveyance system located in Seattle Washington. The tunnel was constructed for the Waste Water Treatment Division of the King County Department Of Natural Resources, from June of 1995 through the first quarter of 1997. The Geologic setting for this soft-ground tunnel consists of glacial, interglacial, glacio-lacustrine, and alluvial soils. This paper, prepared jointly by the owner and con-tractor, will describe project-related site geology, engineering considerations, construction, and dispute resolution/avoidance practices.

Jan 1, 1997

By Clive Wilson, Bruce Hutchison, Daniel N. Adams

Two three-lane highway tunnels, 700 and 2900 m long, make up the driven tunnels portion of Melbourne City Link. Tunnel construction, using design-construct delivery, commenced in May 1996. Construction required excavation through varying rock conditions; temporary support included ground freezing, pipe-spiling, steel sets, and rock bolts. Permanent support for the tunnels required both drained and undrained tunnel cross sections using unreinforced concrete. This paper reviews the construction methods, and highlights some of the not-so-standard designs developed while construction was underway.

Jan 1, 1999

By David G. Rasmussen

With low commodity prices and continuing high operating costs, the mining industry must revise planning and operating to take advantage of every tool available. Conveyors operated within open pits are such a tool. Dravo engineers have designed conveyor systems into pits as prime movers in unique situations. Three cases are presented with economic comparisons made to conventional truck haulage. Increasing energy and labor costs tend to make conversion of prime haulage from trucks to conveyors. Long term pit planning and scheduling reduce the effects of conveyor inflexibility.

Jan 1, 1983

By P. D. Tomlingson

Senior mining mangers that do not get directly involved in the quality of maintenance performance risk the profitability of their operations. Maintenance is not a stand-alone activity. It requires a production strategy that addresses the total life cycle of equipment from procurement to replacement and assures the fully cooperative, mutually supporting interaction of all mine departments. Only senior managers can assure this happens. This paper examines the strategies, policies and actions required to establish and sustain effective maintenance and the profitability that derives from it.

Jan 1, 2004

By D. John Curtis, Gordon S. Crighton, John C. Hester

The six main drives needed to build 55 miles of 4.8 and 7.7 metre i.d. tunnels in 33 months called for careful co-ordination of the design of tunnel boring machines and linings. The implications of these requirements are discussed, with particular reference to the selection of tunnel liners. The solutions adopted are detailed and details are given of the specifications and procedures adopted. The design methods employed for liners are outlined. The construction methods are described and current performance figures given.

Jan 1, 1991

By Michael E. Lively

DOUG HALBE: We've talked about copper operations and gold operations. For our third section on the topic "Operating Ideas That Have Saved Me Some Bucks," we'll turn to the coal fields. Our featured speaker is, I'm almost embarrassed to say, a mining engineer, Mike Lively. Mike has 25 years' experience in the coal industry. He is currently superintendent of surface operations for Southern Ohio Coal Company, Meigs Division (AEP Company). I've read his paper, and there's some really great information here. Mike.

Jan 1, 1998

By E. H. Partelpoeg, B. G. Belew

In 1990, the Chino Smelter completed the construction of a plant designed to recover metal values and water from smelter scrubber effluent. Equipment was installed to maximize effluent recycling and minimize costs. The process utilizes magnesium hydroxide as a neutralizing agent which has the advantage of precipitating copper from solution with minimum generation of solid reaction products. The neutralized stream is clarified, with solids recycled to the smelter for metal recovery while the clarified effluent is recycled to the concentrator for use as process water.

Jan 1, 1992

By R. Krishna

The basic ventilation equation of power equal a constant times quantity to the power three (P=constant x quantity3) makes it an extremely costly palliative as a long term measure. Provision of increased airflow is also limited by maximum tolerable levels of air velocity, the effect upon respirable dust and, in case of coal mines, spontaneous combustion. The paper high lights amelioration measures for climatic improvements at a lower cost. The paper has also shown a method for monitoring air pollution using laser technology.

Jan 1, 1997

By Margaret Armstrong, Arne Berckmans

The longterm aim of this research project is to find fast ways of simulating the recoverable reserves of a deposit for input into financial Monte Carlo simulations without having to conditionally simulate the whole orebody many times. The first step in this re- search is to visualize and quantify the ore tonnage T and the metal quantity Q above an arbitrary cutoff z. This paper presents detailed results for one specific distribution, the lognormal. These lead to a suggestion of a fast way of simulating QTz curves.

Jan 1, 1996