Search Documents

Waste areas of a mine should be sealed especially if there is a risk of spontaneous combustion. Leakage through and around such seals can be problematic. Pressure balancing has been one of the favored options to prevent the ingress of air into these waste areas. Balance chambers require maintenance and monitoring to ensure that they are effective. This paper explores the use of inert gas as a means of controlling ingress of air and egress of waste gases as a means of reducing leakage around seals.

Jan 1, 2009

By Calvin L. Stevenson

The probability of a particle passing through a maze is predictable and consistent. This principle may be utilized to effect a particle size separation of materials by presenting a physical maze to a stream of material that will allow the fine particles to pass, while deflecting the coarse particles. A maze is effective even though all apertures encountered are many times larger than the particles being separated. By designing a machine that allows the probability parameters to be controlled and varied without changing physical dimensions, probability sizing becomes a useful tool for the separation of granular materials.

Jan 1, 1967

By Gary R. Krieger

Baseline Risk Assessment: - Data Collection and Evaluation - Exposure Assessment - Toxicity Assessment - Risk Characterization Lead - Problems and Pitfalls: - Sources - Pathways - Receptors - Toxic Endpoints - Modeling Options - Health Based Clean-Up Options

Jan 1, 1990

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By Edward D. Graf

Once the heavy work of mining, supporting and completing an underground structure is finished, there is frequently the problem of handling unwanted water infiltration into the opening. Methods of controlling the infiltration vary from collecting and channelling the inflow to shutting off the water at the surface of the opening or within the ground formation. Discussed are various methods of controlling ground water inflow from within the structure including collector pipe systems, shotcrete, cement grout, bentonite, and various chemical grouts. Case histories illustrating some of the methods and materials will be presented.

Jan 1, 1987

By Randall J. Essex

The Construction Institute of the American Society of Civil Engineers recently published the second edition of a 1997 publication on geotechnical baseline reports. The new publication, called Geotechnical Baseline Reports for Construction, Suggested Guidelines, represents a 2-year effort that adds three new chapters to the original publication, as well as capturing practitioner commentary through two industry workshop sessions. The paper will overview the contents of the new publication, particularly the three new chapters.

Jan 1, 2008

By M. Rieber

Building on earlier work, an analysis relevant to international (Australasian) minerals trade is developed which accounts for both the impetus of globalization and national reaction or protection. At the firm level, integrated multinationals are contrasted with trade service providers. At the industry level tariff and, particularly, such barriers as quotas, standards, labor and environmental issues are explored. Specific areas examined include: location of both inventories and processing, sources of finance and currency risk, shipping availability and terms as related to processing level, residuals management or environmental controls, and “fair” labor standards. Intraregional rather than global trade is currently most likely.

Jan 1, 2002

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

By N. C. Trivedi

Natural calcium carbonate, commonly known as limestone is an abundant resource pretty much worldwide. Calcium carbonate occurs naturally as the main constituent of chalk, limestone, and marble. One of the unique characteristics of this abundant mineral is its versatility. Major markets for calcium carbonate are: paper, plastics, caulks and sealants, carpet backing, paint, and food additives. This broad spectrum of consuming industries has warranted producers of this industrial mineral to be innovative and quality focused simply to meet the ever increasing demands for performance. This need for improving performance of calcium carbonate has led to the development of new sources of calcium carbonate, natural as well as synthetic.

Jan 1, 2002

Contents

Jan 1, 1985

By Frank P. Frandina

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. The project involves clearance improvements to twenty-eight tunnels, twenty-one of which require structural modification. With construction of the first Package of tunnels just underway at press time, this paper summarizes the program implementation from design through the initial stages of construction.

Jan 1, 2008

By J. P. Morgan

The Vesta Preparation Plant of the Jones & Laughlin Steel Corporation is located on the Monongahela River, eight miles south of Brownsville, Pennsylvania. This plant is capable of cleaning 2400 NT/hr of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables. handle the -1/4" fraction of the raw coal feed. Cleaned -coal goes to boot classifiers where the +48 mesh material settles and is removed by bucket elevators. This 1/4 x 48 mesh material is then sent to centrifugal driers for dewatering. As designed, the minus 48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and dewatered by filtration. The-products of the heavy media circuit, the launder-table-boot-drier circuit and the cyclone-thickener-filter circuit are combined to constitute the shipped metallurgical coal. This Vesta-Shannopin mix is combined at J&L's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke.

Jan 1, 1962

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

Outokumpu Technology’s HSC Chemistry process calculation software enables the user to simulate an entire chemical or physical process. The HSC Chemistry 6.0 contains 21 calculation modules and 11 databases for reaction, equilibrium, heat balance, heat transfer, petrological and simulation applications. Most of the calculation modules automatically utilize the same extensive thermochemical database which contains enthalpy (H), entropy (S) and heat capacity (C) data. This database has been expanded to include more than 20,000 species.

Jan 1, 2007

By Harry R. Dahlberg

Heap leaching is discussed as a unit process. Five factors are identified as the principal elements that can be measured and/or controlled. These are: 1. Material Size 2. Volume of solution 3. Tonnage of heap 4. Time 5. Solution concentretion. The Rate of Extraction Curves obtained from an actual heap or column tests describes the economic viability of the unit process. By analysis of these curves and the five factors end their inter-relationship it is possible to determine how the extraction rate can be increased. The practice of leach and rest used by many operators is analyzed and shown on a hypothetical rate of extraction curve. The influence of the driving force of the hydrogen ion and ferric Lon as Lixivants and its effect on the rate of extraction curve is discussed.

Jan 1, 1979

By T. Patten

Inter-Mountain Labs, IML, performed a study comparing mining waste rock sample analysis by Net Carbonate Value (NCV) and Modified Sobek acid-base accounting procedures. The study looked at 468 waste rock samples and compared the data for Neutralization Potential (NP), Acid Generation Potential (AGP), Net Neutralization Potential (NNP), and the ratio of NP/AGP. The study found that a majority of the samples were below 50 Tons CaCO3/kTons. This subset of ?low-level? samples was also examined separately for Acid Base Accounting parameters. The analysis compared the NCV procedures to the Modified Sobek procedures and concludes that the NCV procedures are as protective of the environment as Modified Sobek procedures.

Feb 27, 2013

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

By W. T. Walter

High-G centrifuges from five preparation plants were sampled to determine and quantify the various operating factors affecting performance. The operating factors that were considered include feed rate and percent solids, size of feed material, screen-basket type, hardness of coal and age of the flights. The performance parameters that were measured include product surface moisture, recovery and degradation of the coal. Regression equations with good significance levels were developed.

Jan 1, 1982

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984