Search Documents

By Janet A. Johnson, T. B. Borak, K. J. Schiager

INTRODUCTION In the USA regulatory agencies have adopted standards which limit the allowable concentration of ore dust in underground uranium mines. The American Conference of Governmental Industrial Hygienists has recommended a threshold limit value for silica which has been incorporated by reference in federal regulations (30 CFR 57, 1980). The Nuclear Regulatory Commission (NRC) imposes a limit for unprocessed uranium ore dust for reducing the exposure to radioactive materials from inhalation (10 CFR 20, 1980). We have been unable to trace the origin of the NRC standard. Recently the ICRP has published recommendations concerning limits for intakes of radionuclides by workers (ICRP, 1979). We have used the ICRP methodology to compute the dose equivalent commitment to lung and bone from inhalation of insoluble ore dust particles. These values were used to derive air concentrations which would provide an acceptable risk for induction of cancer from occupational exposure. Results indicate that the new ICRP recommendations are more restrictive than the present NRC standard for radioactivity. The maximum allowable dust load in a uranium mine will depend on both the concentration of silica (% Si02) and the amount of radioactivity (% U308). We have combined these standards assuming complete independence of biological hazard to establish boundary conditions for which either silica or radioactivity is the dominating factor. Based on these results we present suggestions for analysis of ore dust to insure compliance with regulatory agencies. SILICA STANDARDS Silicosis, fibrotic lung disease produced by crystalline silica, was one of the earliest forms of occupational disease to be recognized. The pulmonary lesions caused by silica, silicotic nodules, consist of concentrically arranged bundles of collagen fibers. Fusion of these nodules results in progressive massive fibrosis causing alveolar changes which decrease ventillation and blood flow in the lungs. The current Threshold Limit Value (TLV) for mineral dusts is based on the concentration of free silica. The standard is expressed in three forms: (1) Particle count standard: TLV (mppcf) = 300/(% Si02 + 10) (mppcf = million particles per cubic foot) (2) Respirable dust mass standard: TLV (mg/m3 ) = 10/(% respirable Si02 + 2) (3) Total dust standard: TLV (mg/m3 ) = 30/(% Si02 + 3) The most commonly used form is the respirable mass standard. These curent values for silica are based primarily on epidemilogical studies of Vermont granite workers and other occupationally exposed workers. In the Vermont study no cases of silicosis were seen in individuals employed after dust control measures were initiated and whose subsequent exposure averaged less than 5 mppcf. The free silica concentration in the airborne dust to which these workers were exposed averaged 25%. A concentration of 10 mppcf of granite dust is considered equivalent to 0.1 mg/m3 quartz. The current respirable mass standard allows a maximum silica concentration of 0.1 mg/m3. NIOSH (1974) has recommended a reduction in the current TLV for respirable silica to 0.05 mg/m3 Si02. As with radiation standards, the TLV for mineral dusts is an upper limit for time weighted average exposure. It is recommended that dust concentrations be maintained as far below the TLV as current practices permit. RADIATION STANDARDS The present concentration limit for airborne natural uranium in ore dust prior to chemical separation is 75 µg of uranium per m3 of air ( 10 CFR 20, 1980) . This corresponds to 1.85 Bq/m3 (50 pCi/m3 ) of natural uranium, U-238, U-235 and U-234 and is equivalent to 3.7 Bq/m3 (100 pCi/m3 ) of gross alpha activity with radioactive equilibrium between the long-lived alpha progeny through Ra-226. The origin or basis for this standard is not known, but it presumably includes both chemical toxicity and risk from somatic radiation injury. Recently the International Commission on Radiological Protection (ICRP, 1977) has published recommendations concerning the objectives and criteria for limiting radiation exposures. This was followed b y a revision of the limits for intake of radionuclides by workers (ICRP, 1979; ICRP, 1980). The previous compilation of limits for internal emitters was published by ICRP Committee II in 1959 (ICRP, 1959). The latest version includes new methodlogy outlined in ICRP Publication 26 (ICRP, 1977) as well as extensive metabolic information

Jan 1, 1981

By Russell L. Dahl

In a continuing effort to improve plant efficiency, United States Steel's Atlantic City Ore Operations completed the rubber lining of its balling drums in late 1982. This resulted in benefits of reduced bentonite consumption, reduced maintenance costs, improved production rates, and lower power consumption. These advantages far outweigh the disadvantages of increased oversize production and increased surging on the roll screen sizing devices. Certain operating characteristics and variables are discussed herein.

Jan 1, 1983

The Mine Safety and Health Administration (MSHA) academy in Beckley, WV, received enquiries from various segments of the mining industry concerning alcohol and substance abuse in the mining industry. The MSHA Director formed a committee, the Mining Industry Committee on Substance Abuse (MICSA), to deal with these enquiries. The committee met in April 1985 at the mining academy in Beckley. The MICSA committee expanded its membership to represent labor, management, and government agencies affiliated with the mining industry as well as government agencies dealing with alcohol and drug abuse. This expanded 18-member committee met for the first time in July 1985. At that time, two cochairmen were elected, one from labor and one from management. MICSA has spent time on education by sharing information on the issues and by calling in outside experts for advice and consultation. The committee also initiated several projects. These include a resource manual on substance abuse and employee assistance programs. Mine operators and labor unions can use these programs as guides. MICSA is also assembling statistics on substance abuse, particularly as applied to mining. And the committee commissioned an Education film, Substance Abuse, Is It Our Problem? (The results of a survey on drug use, given in Table 1, suggest that substance abuse may indeed be a problem.) The educational film, produced by MSHA, is an introduction to the problem of substance abuse in the mining environment. The film encourages mine operators, labor unions, and miners to analyze their individual circumstances to determine whether a problem exists. The film also offers ways to deal with the problem. And the film invites the mining industry to request additional information from MICSA. There is no single approach to substance abuse that will fit the need of every mining operation. As with any health, safety, or production problem, remedies must be site specific. MICSA's aim is to channel ideas to those who seek to help employees in a mining environment who seek to rid themselves of alcohol and substance abuse. As stated more formally: The Mining Industry Committee on Substance Abuse represents the efforts of labor, management, and government. The mission of the committee is to make the mining industry aware of the problems resulting from alcohol and other drug abuse and to recommend possible methods to remedy the problem. The function of the committee is to assist the industry in developing programs and resources to recognize and provide help for troubled employees, and thus reduce the risk of accidents, while lower absenteeism and increasing productivity.

Jan 11, 1987

By L. Adler

In spite of distractions from glam-our areas (ground control, computers, etc.), excavating and bulk handling in mining remains paramount but is now undergoing dramatic advances. The massive intervention of mining and civil engineers as "engineer-users" into the tight, exclusive, and specialized bond between the equipment operator ("operator-users") and the manufacturer (mechanical engineers "and sales "reps") has now occurred. Three developments have accelerated this: 1) larger, more costly, complex, specialized, and innovative equipment; 2) a more profound understanding of the equipment, operations, and working conditions (encumbered space); and 3) a concurrent thrust into "high-tech," (automatic and remote controls, sensors, automation, artificial intelligence, and even robotics) and human factors (workload intensity, work-station design). This has produced a well-defined professional discipline, including construction and even military engineering. The mine plant, and to a lesser extent, the mine face, is now being monitored. Equipment conferences, journals, and centers at universities and agencies have multi-plied. The discipline's impact on future mining now becomes more apparent.

Jan 1, 1988

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By D. E. Munson

The Waste Isolation Pilot Plant (WIPP) Project was established in 1975 by the Department of Energy (DOE) under Public Law 193 to develop the necessary technology for safe disposal of radioactive wastes from the defense programs of the U.S. The technology development involves extensive theoretical, numerical, and laboratory programs, as well as construction of the WIPP facility in southeastern New Mexico for in situ testing and waste storage demonstration. If after the demonstration, the facility is found to comply with regulations of the Environmental Protection Agency, then the facility will become a repository for Transuranic (TRU) waste. The underground portion of the facility is 655 m beneath the ground surface in massive natural salt deposits of the Salado formation, as shown in Figure 1.

Jan 1, 1991

By Rick T. Richins

Despite what may be overwhelming evidence that natural degradation of cyanide and cyanide attenuation in hydrogeochemical processes are capable of reducing or eliminating potential water quality problems associated with heap leach facilities, the recent sharp increase in the price of gold and wide interest in the cyanidation process has focused all regulatory eyes on cyanide leaching. Regulations continue to increase, design criteria are more strict, and detoxification requirements approach or exceed the level of detectability. Current governmental regulation of mining and milling operations using cyanide varies considerably from state to state. The lack of regulatory consistency at this level is largely attributable to the current Bevill Amendment exclusion of mine wastes as potentially hazardous wastes, the undefined status of the Environmental Protection Agency's ongoing mine wast study effort, and the mining industry's reluctance to develop a consistent policy regarding state versus federal mine waste regulation.

Jan 1, 1998

By Gail L. Achterman

Most mining companies today perform site assessments and operational or compliance audits regularly. The purpose of these audits is to review company facilities and operations to determine whether they comply with applicable federal, state and local environmental laws and regulations. Why Audit? Companies adopt assessment and audit programs for legal and business reasons. The business reasons include: (1) ensuring efficient and cost-effective compliance through early problem identification and resolution; (2) planning and implementing business transactions such as real estate conveyances, loans, mergers and acquisitions, and waste disposal service contracts; and (3) employee training and relations. Legal reasons for audits include: (1) avoiding enforcement actions and penalties; (2) meeting environmental permit certification requirements; (3) avoiding corporate officer liability; and (4) meeting Security and Exchange Commission disclosure requirements. The Environmental Protection Agency ("EPA") encourages environmental auditing by regulated entities. The EPA Environmental Auditing Policy Statement was published in the Federal Register on July 9, 1986 (51 Fed Reg 25,004). Although the existence of an auditing program does not create a defense to or otherwise limit a company's regulatory responsibilities, EPA considers compliance programs in setting inspection and enforcement priorities. If a company makes an honest effort to identify and correct its own problems, EPA's enforcement approach is influenced, especially if violations are promptly reported. Perhaps more significant to many executives, the U.S. Department of Justice issued guidelines last year on when it will pursue criminal prosecution for environmental violations. See Department of Justice, "Factors and Decisions on Criminal Prosecutions for Environmental Violations in the Context of Significant Voluntary Compliance or Disclosure Efforts by the Violator," (July 1, 1991). It is now commonplace to read about major companies pleading guilty to criminal violations and paying millions of dollars in penalties. For example ALCOA recently agreed to pay criminal fines and civil penalties totaling $7.5 million for unauthorized excavation of PCB-contaminated soil and improper dumping of spent caustic solution. No executive wants to explain to the Board of Directors or shareholders why the company was criminally indicted. The Department of Justice considers factors such as voluntary disclosure, preventive measures and compliance programs, such as a regular compliance auditing program, the effectiveness of the disciplinary system for employees who violate the company's environmental policies, and subsequent compliance efforts by companies to remedy ongoing noncompliance. The Department of Justice looks closely at whether audit recommendations were implemented in a timely way and whether environmental compliance was a standard by which employees were judged. The Lawyer's Role. The role of the lawyer in an audit team deserves special attention. When enforcement action or litigation has begun or is contemplated or a government agency has asked for information, attorneys always should be directly involved in environmental audits. In most situations, however, environmental audits are management tools, and the attorney's role should be to advise the team. The attorney can help make sure the team understands the laws and regulations the facility must

Jan 1, 1992

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008

By Emily Adelsohn, Robert Winn, Anthony Iannacchione

"Over 600 longwall panels have been mined in Pennsylvania in the last 50 years. Of those 600 panels, 25 panels undermined interstate highways. Despite this quantity of panels, much is still unknown regarding the detailed effects of undermining highways. The Gateway Mine, the Emerald Mine, and the Cumberland Mine undermined I-79 with 17 panels between 1982–1989 and 2003–2008, respectively; mine Eighty-Four undermined I-70 with 4 panels between 1987–2000.Through the examination of the panels that undermined I-70 and I-79, it is possible to determine which factors have most impacted the highway alignments. In some locations, the highway intersects with panels at angles ranging from 45 to 80 degrees, and at others, it runs between two panels, which simulates the effect of gateroads on the subsidence. The panels width to overburden ratio varies between 0.64 and 1.7, meaning that the interstates were influenced by both subcritical and supercritical subsidence basins. The face advance rates and overburden depths also vary between the panels.Unfortunately, specific information detailing highway impacts associated with unique characteristics of the subsidence basins are limited. However, using the profile function model and influence function model within the Surface Deformation Prediction System (SDPS), the effects of overburden, panel size, and orientation of the road to highway can be indirectly assessed by profile and influence models of subsidence basin formation.INTRODUCTIONCoal mining has been an integral part of Pennsylvania’s history. Room-and-pillar mines have been active since the late-1700s when coal was extracted from outcrops. By 1830, the city of Pittsburgh alone consumed more than 400 tons of bituminous coal each day for domestic and industrial use (PADEP, 2019). In the late 1960s, the face of mining in Pennsylvania changed with the development of full extraction longwall mines. Since that development, over 600 longwall panels have been mined in the Pittsburgh Coalbed in Pennsylvania alone (PADEP, 2019).As longwall mining and other forms of full extraction mining have increased in popularity, the amount of planned subsidence impacting the surface has also increased. The stresses and strains induced by longwall subsidence can cause damage to the surface as well any structures, water supplies, or water bodies that lie above the panel. Since the behavior of soils and structures vary, one way to study the surface effects of longwall mining is to analyze the impact on flat, rigid, pavement surfaces. Examining factors that vary the impact of subsidence with respect to highway alignment can demonstrate the favorable orientation of an alignment to avoid or mitigate damage and critical impact zones in a subsidence basin."

Jan 1, 2019

By Wilbur J. Morin

Construction of Flaming Gorge Dam in northeastern Utah necessitated the construction of a new state highway, Utah-260, to provide access to the dam and the town of Dutch John. A 550-foot arch structure was designed to span Cart Creek, about one mile southwest of the dam. The rock exposed at the site is highly fractured quartzitic sandstone with interbedded shale of the Precambrian Uinta Mountain Group. Eight exploratory holes were drilled, four in each abutment area, to determine rock types, the extent of fracturing at depth and rock strength. Drill cores in the west abutment revealed blocks of quartzitic sandstone loosened by the weathering and partial removal of underlying shale beds. The rock in the east abutment area was found to be highly fractured to depths of 70 feet and as far east as 50 feet from the footing locations. Selected core sections were tested for unconfined compressive strength but the values were not considered-representative of the in-situ fractured rock. To prevent movement along or, perpendicular to open fractures, four drilled-in columns were provided at the base of each footing. These extended 50, feet beyond the base of the footing, along the bearing and inclination of the thrust reaction.

Jan 1, 1963

By Rod L. Norfleet

Cemented tungsten carbides are a sintered powder - metallurgical product essential to modern industry. Because of their moderate unit price and our dependence upon foreign sources for the component raw materials, a growing recycling industry has developed in the United States. There are two basic approaches taken to recycling cemented carbides; those which leave constituting materials unaltered or direct-reuse and those which separate the constitutes back to the raw components. To separate the carbides back to their raw components usually requires expensive chemical processing and is thus confined to the lower value materials such as grinding sludges. The direct-reuse methods recycle cemented carbides back to an intermediate level, a powder capable of being recompacted and resintered into a functional end-product. The three most commonly used methods of direct-reuse recycling, the coldstream process, bloaching and the Bernard or zinc process, are reviewed,

Jan 1, 1984

By M. SIDDARAJU, Rameshwar Sah, Satendra Kumar, Arvind Jaiswal

The study explores a novel process to sinter porous iron ore with improved productivity and quality. The iron ore is pre-processed with calcined lime to temporarily close pores, preventing water absorption during granulation. This enhances reaction kinetics and early slag formation during sintering, resulting in significant improvements in sinter productivity, product yield, and cold strength property.

Feb 28, 2022

By M. P. Adamson, Bryson D. Trexler, R. V. Ramani, Mark L. Koenig, V. Rajaram, Alan Burton, C. S. Crocker, Kim. Y. C., A. G. Law, William C. Larson

Another record year vas experienced by the mining industry as the value of nonfuel minerals production soared to $23.5 billion-up 15% from the previous year. Based on preliminary estimates by the Bureau of Mines, US mine output was the basis for about $225 billion worth of minerals-derived materials. Metal mining accounted for $8.5 billion, or 36%, of the total. Of the 22 metals produced in the US, 11 showed quantity increases, while 16 had value increases. Business Week's survey of 1200 companies (Mar. 17, 1980, pg. 81) revealed that 21 metals and mining companies had sales increases of 30% with earnings up 104%. Higher prices and increased demand for metals were primary factors behind the improved performance. The steel sector reported a 30% decrease in earnings for the year, but the slump was primarily the result of a $383-million loss for US Steel coupled with a 17% decrease in earnings at Inland Steel. Other firms did well in 1979, with earnings up 279% at Interlake and 269% at Kaiser Steel. Major obstacles facing the steel industry included substantial tonnages of dumped and subsidized imports, environmental expenditures, runaway inflation, and price controls. Turning to nonmetallic production, of the 49 commodities reported by the US Bureau of Mines, 29 had higher outputs and 39 had increased values. While production statistics may seem encouraging, government regulations continued to stifle industry efforts to develop needed new capacity. A case in point may be publication of the Environmental Protection Agency's simplified procedure to streamline five permit programs by consolidating them into one. The five included: hazardous waste management, national pollution discharge elimination, dredge and fill, underground injection control, and prevention of significant deterioration. The new procedure, published by EPA in the Federal Register, took 149 pages. AMC's J.A. Overton, Jr., noted that (MCJ, Nov. 1979, p. 39) to visually depict the complexity of the proposed regulations, Sell Oil Co. developed a flow chart mapping a path through one section. The chart required 10 days to map and two weeks for two draftsmen, using computerized drafting techniques, to plot the results. Overton said, "Perhaps the greatest service EPA has performed in preparing its proposal is to demonstrate again that federal regulations have become a complexity compounded by confu¬sion that culminates in a conundrum." While regulatory agencies promulgate new regulations, the lack of a cohesive government minerals policy remained a matter of significant importance to mine management. A non-fuel minerals study to provide input to the Administration for a national minerals policy program was a dismal shock, according to Rep. Jim D. Santini (D-NV). He said the first phase of the program, which was to identify industry problems, failed to come to grips with the hard decisions necessary regarding these problems, their impact, and their interrelationship. Santini said the report failed to acknowledge government's role in the process and absolved the government of any adverse influence on the domestic minerals industry. In response to the phase one report, eight senior mining executives testified before Santini's House Subcommittee on Mines and Mining concerning mineral supply, access to foreign sources, environmental protection, conservation and recycling, national security, and capital formation. By year's end, Rep. Santini promised to prepare a hard-hitting committee report on problems affecting the non-fuel minerals industry to provide a better base for subsequent policy recommendations (MCJ, Jan. 1980, p. 34). On the technological front, interest again centered on mechanization, automation, and scaleup to improve and expand production. Computer use increased for calculation of ore reserves, mine planning, operations research, and mineral processing.

Jan 5, 1980

By Stefano Ceccotto, Eugenio Trussoni

"INTRODUCTION Contemporary city is made of layers. Physical structures layers (built fabric, residential, commercial industrial etc. ), infrastructural layers (below and above ground), “green” layers (parks and open spaces), and also informational layers, i.e. connections, links, between sectors of the city and other territories. The “city of layers” concept represents the exercise of “rebuilding the city” per each layer, highlighting those physical built structures that are functional to define a relation. For example, if consider the “connection” relation, the city is re-designed by considering only transportation built structures. The layer obtained in such fashion is hence the “transportation” layer, including below grade infrastructures (subways) and above grade lines (rail, bus, tramways etc.), as below shown in Figure 1.In this sense, the contemporary city is represented by separate constructs assembled together according to a specific functionality (e.g. “connection”). As a consequence, the relation between what is built underground, and the related above-ground development, can be perceived in his most evident appearance. What could happen within the contemporary city if the planning process would begin from below to above and not vice-versa?INTERACTION The question risen in the introduction is strategic when approaching the difficult task of designing (or re-designing) a multi-level organism like the contemporary city. Nowadays, the theme of integration between underground and at-grade master planning has become the subject of many urban renovation projects, where the design process has begun within the transportation layer, underground, and further developed by interacting with at-grade structures already existing or in phase of design.A series of case studies where below/above interaction plays a key role in the project will be further analyzed. Moreover, it is relevant to understand the mechanics of an urban transformation process that originates within the transportation layer and ends up with the design of entire sectors of the city. The Transit Oriented Development approach is a useful tool to clearly understand such transformation process. TOD has become, in particular in the last decade, one of the most effective tools for urban design, in order to solve simultaneously the many different instances related to transit planning, urban design and real estate market."

Jan 1, 2016

By Steve Kral

Worker safety is an issue that transcends industries, whether it be mining, construction, manufacturing or even general office work. In the mining industry, safety and training are particularly important because mining is a dangerous occupation. Throughout the years, federal and state safety regulations have been written and revised to keep up with the changing technologies. And mine operators have installed their own safety and training programs. They have come to realize that a safe and healthy workforce has positive effects on productivity and profitability —not to mention avoiding the high costs of injury-related absenteeism.

Jan 1, 2003

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The US Bureau of Mines (USBM) and Amax Coal Co. studied surface coal mine overburden blasting near four steel and one PVC pipeline of 15 to 51 cm-diam (6-20 in.-diam), monitoring vibration, strain and pressure. Unlike tests of small blasts simulating construction, these were up to 1 t (2200lbs) per delay in 31-cm (12-in.) blastholes. Worst-case comparisons showed that 12.7 cm/sec (5 in./s) blasting vibrations produced strains about one fourth that of pressurization and 10% to 18% of the ultimate tensile strength. No failures occurred from blasting as close as 15 m (50 ft), which produced vibrations over 60 cm/sec (24 in./s).

Jan 1, 1995

By J. A. G. Llerena, J. Sattarvand

Tailings dam failures have been occurring in recent years. They are considered more vulnerable than hydraulic dams due to the lack of regulations on specific design criteria, and stability requirements regarding monitoring during the construction and maintenance process. Thus, monitoring the dam is essential to know the dam's existing state and ensure its safety. One of the reasons tailings storage facilities fail is slope instability caused by moisture content. A relationship does exist between moisture content and surface strength, early detection of seepage would help to assess the physical condition of the dam. Moreover, to cover the tailings dam area in an efficient way Unmanned Aerial Vehicles (UAVs) are suitable because of their versatility and high-resolution data acquisition. Mounted with a high-resolution RGB camera, and thermal, or hyperspectral sensors UAVs can acquire good quality images that combined with image analysis and machine learning algorithms yield a good estimate of soil moisture.

Feb 1, 2023

By S. A. Pierce

Heightened environmental consciousness has resulted in the development of various international accords dealing with natural resource management. This international awareness is now being translated into regional and local initiatives that proactively implement collaborative environmental management programs. One such program was recently initiated in northern Chile in recognition of the interconnection of Andean salars. Cooperative efforts between industry, governmental agencies and academic professionals have resulted in the implementation of simultaneous environmental monitoring of flora and fauna in the salars of northern Chile. This coordinated effort is leading to an improved understanding of the migratory patterns of South American fauna, as well as improved access to an expanded database for the multiple user groups associated with the Andean salars. The El Abra Mine is actively participating in these coordinated monitoring efforts.

Jan 1, 1999