Search Documents

By M. L. Bricker

The Jim Bridger Mine is operated by Bridger Coal Company and is located in Sweetwater County, 35 miles (56 km) northeast of Rock Springs, Wyoming (USA). The general location of the mine site is shown on Figure 1. Bridger Coal is a joint venture of NERCO Coal Corp, the operator, and Idaho Energy Resources Company. The permit boundary encompasses in excess of 20,000 acres (81 km2) and is nestled against the western side of the Continental Divide. Production started on July 3, 1974, and the mine has produced approximately 90 million tons (82 million t) while moving approximately 450 million cubic yards (344 million m3) of virgin earth. Annual production averages 5 to 7 million tons (4.5 to 6.4 million t) of run-of-mine coal. Coal is consumed on site by the Jim Bridger Power Plant, a 2,000-megawatt generating station, and the electricity is transmitted to the Pacific Northwest power grid (Oregon, Idaho, Northern California, etc.).

Jan 1, 1991

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By R. Schlüter

"The global mining industry is facing increasing challenges in terms of geological, technological and social aspects. Potential exploi-tation of deposits shows a tendency to increasing depth with complex ores and decreasing grades. A promising approach to deal with these constrains is by applying alternative extraction methods like (bio-)hydrometallurgy as in-situ leaching (ISL) technology. The Bergakademie Freiberg University of Mining and Technology established the “Biohydrometallurgical Center for strategic Elements” (BHMZ) to foster the interdisciplinary research along the entire biohy-drometallurgical process chain to extract indium from sulfide ores. The involved Department of Underground Mining Methods deals with the design and implementation of a pilot-scale underground testing facility for microbial in-situ stope leaching in its “Research and Educational Mine”. This paper discusses the potential of in-situ bioleaching under technological aspects. In addition, different conditioning approaches based on hydraulic and explosive methods for enhanced permeability in the formation are introduced and the gathered data will be presened. INTRODUCTION A reliable, substantial and sustainable supply of raw materials is of crucial importance for any industrialized country. This dependency applies to “strategic elements” including rare earth elements (REEs), platinum group metals (PGMs) as well as a variety of other metals like indium and germanium which are needed for high-tech industry and products such as electric and electronic devices, fibre optics and laser technology (Barakos et al., 2016; European Commission, 2010). Due to the economic growth of the BRIC-countries (Brazil, Russia, India, China), the resource policy of China as well as the volatile world mar-ket prices of different metals the availability of these critical raw materi-als and therefore the dependency of the high-tech producing countries has become increasingly important (Barakos et al, 2016). Adequate supply is often affected by the increasing depth of de-posits, lower metal concentrations and more complex ore mineralogy. In addition, mining activities are increasingly restricted by their envi-ronmental and social impact and footprints. As a consequence, con-ventional mining and processing methods are limited by high energy consumption and technical constraints."

Jan 1, 2018

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

By F. Wolf, R. Ellmies

"Fluorspar is one of the most important industrial minerals. It has a wide range of applications, for example it is used in the steel and aluminum industry, and is also the raw material to produce hydrofluoric acid, Teflon or Gore-Tex. There are only a few major fluorspar mines worldwide, with China being the most important fluorspar producer (U.S. Geological Survey National Minerals Information Center, 2017). At Okorusu, Namibia, fluorspar has been mined with conventional open pit mining methods from 1955 until 2014 from a large scale metasomatic fluorspar deposit with seven identified orebodies. There are about 7 million tons of measured resources left with an average grade of 27.5 % CaF2. This paper is based at an MSc thesis at Technical University Freiberg and describes the design of an underground mine for the A and D orebodies with an annual production rate of 100,000 t acid-grade fluorspar product. By comparing different mining methods and adapting variants of access to the underground orebodies the paper will emphasize on the selection of a suitable mining technology, with a special focus on the economic considerations to decide about the most profitable operation. INTRODUCTION Mining holds an important part in the economy of Namibia. In 2016 11.1 % of the GDP was made through mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists an underground mining operation. The global annual production of fluorspar is approximately 6 to 7 million t (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu produced on average about 50.000 t annually in recent years (U.S. Geological Survey National Minerals In-formation Center, 2015). Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an open pit mine with four individual pits (A-D) since 1980. In 2014 the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village. The intent is to develop a concept for the further underground development of the mine. There are still about 7 million t of measured resources left in the deposit, with an average grade of 27.5 % CaF2. This study focusses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged."

Jan 1, 2018

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By W. D. Keller

Scan electron micrographs, SEM's, will be shown of representative refractory clays from Missouri deposits, with counterparts from other localities. The story is in the pictures, ("1000 words in each picture"), but clay types include the following. Plastic, semi-plastic, and semi-flint "fire clays" of Missouri have textures which appear to retain certain relic texture of ball clay. Flint clay is composed of tightly interlocking packets, sheaves, and books of kaolinite. Diaspore and boehmite mineral textures characterize those "clays". Surface-boulder diaspore shows very pronounced recrystallization and crystal enlargement from original, unexposed first-grade diaspore.

Jan 1, 1977

By Fred Morelko, Michael Connelly, Brad L. Ricks

INTRODUCTION The $1.1 billion Bajo la Alumbrera Project, started up in 1997 by Minera Alumbrera Limited in the Catamarca Province of Northwestern Argentina, is the first large scale modern mining project to be developed in Argentina. Like many modern Andean mining projects, existing infrastructure was not available to economically transport the 875,000 tonnes of product per year. A variety of alternatives were investigated, including upgrading of existing roads and railroads, slurry pipelines, and combinations of these systems. The final system selected was to combine a 312 km slurry pipeline with an 820 km rail haul to a ship loading facility near Rosario. The concentrate pipeline crosses divergent terrain between the minesite at 2400 m elevation and the filter plant at 400 m elevation. The system selected represented the lowest net present cost alternative by a significant margin. BACKGROUND The Bajo Alumbrera deposit was discovered in 1947 by Professor Cetioni from the University of Tucuman. It is a large (>750 million tonnes) medium-grade (0.6%) copper deposit with high gold values (0.5 g/t*). The deposit outcrops, making it very suitable to modern, large scale, open pit mining techniques using 218 t trucks and 43 m3 shovels. Advances in gravity concentration of the gold helped to demonstrate the feasibility of the project in a study prepared by Fluor Daniel for Minera Alumbrera in 1994. The initial concentrator is the largest green-field concentrator ever constructed, rated at 85,000 t/d. Production will peak at 190,000 tonnes of copper metal and 710,000 troy ounces of gold per year, one of the top 10 copper and top 15 gold producers in the world. * Throughout this paper, the word tonne and abbreviation refer to the metric ton of 1000 kg.

Jan 1, 1998

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997

By R. Leithner

The need/wish to sequestrate CO2is based on the assumption of the International Panel of Climate Change (IPCC), that CO2 maybe the major driver in climatic changes, i.e. especially the anthropogenic CO2emissions due to the combustion of fossil fuels like coal, oil and natural gas will increase the atmospheric CO2-content, which will lead to higher temperatures in the atmosphere. The 0.03% CO2in the atmosphere have a 22% share of the natural greenhouse gas effect of 33 K necessary for life on earth. The main share of 62% has the water vapour in the atmosphere. Only if one concentrates on the greenhouse gas effect of the gases beside water vapour, CO2 becomes most important with 58% influence. In addition there are other influences on the climate like: • Eccentricity of earth’s orbit, precession of orbital plane, obliquity and precession of earth’s rotation axis (Milankovitch’s theory) • Sunspots and magnetic field of the sun • Changing streams in the ocean • Volcanic activities • Distribution of continents on the surface of the earth • Impact of meteorites • Change of insulation by interplanetary dust [Muller, R.A. 2000] etc. To answer the question, if the CO2-content in the atmosphere has an important or exclusive influence on the earth atmospheric mean surface temperature, one should look into history. Figure 1shows the mean temperature of the atmosphere and the atmospheric CO2-content time histories 1 billion years back; no correlation can be found between them. Nevertheless a lot of countries have committed themselves to reduce their CO2-emissions.

Jan 1, 2004

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Most, if not all longwall gobs contain explosive gas zones (EGZs), i.e., zones of explosive methane-air mixtures that can cause – and have caused – mine fires and explosions. If the coal is prone to spontaneous combustion, oxygen penetration into the gob must be avoided. This paper summarizes the significant research findings from five years of computational fluid dynamics (CFD) modeling research conducted at the Colorado School of Mines (CSM) under funding from the National Institute for Occupational Safety and Health (NIOSH). CSM Researchers have developed CFD modeling techniques to identify where and under what circumstances EGZs can form in longwall gobs and how EGZ formation and oxygen penetration depend on the ventilation method, face and bleeder ventilation parameters, injection of inert gases and the operation of gob ventilation boreholes. Recognizing these explosion and fire hazards is an important first step in improving the safety of longwall coal mines. CSM modeling research has shown that EGZ formation can be effectively controlled by adjusting ventilation parameters, choosing the proper ventilation pattern and injecting inert gases where necessary. INTRODUCTION In a project sponsored by the NIOSH Office of Mine Safety and Health Research, researchers at the Colorado School of Mines have examined gas compositions and flows in longwall gobs in order to assess explosion and fire hazards. Since gob areas are inaccessible, researchers developed a series of computational fluid dynamics (CFD) numerical modeling tools to characterize these hazards. A variety of CFD models were developed to cover progressively sealed as well as bleeder ventilated gobs for both coal and trona mines. The explosion and fire hazards posed by EGZs in longwall gobs can be summarized as follows.• If the EGZ lies closely behind the longwall face, flames and pressures from an explosion can penetrate the shield supports and reach the active face area, creating blast trauma, burn hazards and toxic, unbreathable atmospheres. • EGZs can be pushed around inside the gob by roof collapses and cave-ins. If they get pushed out into the face area, sudden methane inundations and explosion hazards in face areas can result. • Fresh air flowing into the gob can create an explosion hazard as the gas composition in the gob moves from fuel-rich inert to explosive, creating EGZs. • Ignition sources inside the gob can be frictional ignitions or spontaneous combustion. • Bleeder ventilated gobs are surrounded on all sides by an EGZ that forms along the fringe areas between the fresh-air ventilated bleeder entries and the methane-rich interior of the gob. It is suspected that diffusion flames can propagate rapidly along these EGZ fringes if an ignition occurs"

Jan 1, 2015

By W. L. Hollinshead

For more effective and cost saving production in tunnels, the machinery used on construction sites will be equipped with guidance systems combined with working procedure management systems. This paper describes sensors for these systems and various system configurations. A project is described which uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 1999

By G. E. S. Valadao

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake pore microstructure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 µm, length of 500 µm and height of 4000 µm. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: I) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method, 2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4) some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By Z. T. Bieniawski, José Miguel Galera, Benjamín Celada

TBM case histories from over 400 tunnel sections are analyzed presenting a comprehensive application of the Rock Mass Excavability (RME) index (Bieniawski et al.2006). The paper introduces two new adjustment factors, called the Factor of Tunnel Length and the Factor of Crew Effectiveness, which were established to represent more realistically the interaction of the rock mass characteristics, the TBM parameters and the performance of the crew operating the machine. A new correlation is provided for predicting the average rate of advance of double-shield TBMs working specifically in the double-shield mode.

Jan 1, 2007

By J. Chai, Y. Qiang, D. D. Zhang

"In order to control Quaternary loose layer settlement in East China, there are monitoring results based on the 3 water level observation holes and 7 sand layer of fiber Bragg grating (FBG) strain sensor. Un-der the conditions of upper group water injecting to lower group of loose layer, the deformation characteristics of upper, middle and lower group of loose sandy soil layer changing with time and relationship with the water level are studied. The constitutive relation of stress-strain is also studied at different sand layers. Research results show that using water injecting from upper group into lower group of loose layer can ease the loose layer compression deformation. With the water level dropped, in East China soil creep deformation occurred, which accord with viscoelasto plastic model. The deformation of lower sand group has clear later effect and no direct relationship with water level. The results provide an important basis for the study East China stratum settlement model and water management. INTRODUCTION Ground-surface subsidence is a common geological disaster, which has the features of continuous, changing slowly, concealment (Y.P. Yin et al. 2005). Today, due to underground mining and constructions in formation compression, surface subsidence is wide-spread in the world, which is the environmental geological problems in the worldwide that cannot be ignored (Y.Q. Xu et al. 2006, D.L Gallo-way et al. 2000, Qiu, B. et al. 2011). The eastern region of China has generally geological disasters in coal mine geological caused by the thick loose layer settlement like as mine shaft failure. Stratum dehydration consolidation is a major cause of loose layer settlement (H.Y .Liu et al. 2007). A method of water injection using ground water to stable water level is proposed, which can effectively control the loose layer caused by compression settlement(J. Chai et al. 2012&.2013). Accurately knowledge the characteristics of strata deformation is the premise of settlement management (Q.C. He et al. 2006). Previous re-search (J.F. Miu et al. 1996, X.Y. Gu et al.1998, Y. Zhang et al. 2006), mainly studies are focused condition of the city pumping irrigation, de-formation characteristics of middle and up loose layers. On a group of aquifer in East China, the loose layer losing water is caused by coal mining, bottom water drainage and overlying strata water flowing fractured zone hydrophobic induced by mining, which the dehydration conditions have great difference from one to another. The Position of water loss is centralized in bottom aquifer, and the formers of ground subsidence geological environment and settlement mechanism are different. According to the study of stratum settlement, usually the de-formation of sand layer is ignored(C.H. Liu et al. 2004), but few studies show that the sand layer have the plastic deformation, and contains the creep deformation, water content of sand soil may become the main settlement layer (Z.X. Wei, 2002, C.H. Liu et al. 2004)."

Jan 1, 2015

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sub) coal which may be mined when the better deposits are depleted.

Feb 24, 1997

By F. Segobia, M. Portal, F. Ysla, A. Mujica, L. Goicochea

The “Building Our Future” project is a collaborative initiative between the UNC SME Student Chapter and the Water and Earth Museum (MAT) of Asociación Los Andes Cajamarca (ALAC), both corporate entities of Newmont Yanacocha. Its mission is to promote responsible and sustainable mining among new generations while fostering a culture of equality and respect. This comprehensive educational program integrates sustainable development goals and includes workshops led professionals and external experts who share their personal stories to inspire students from rural and urban educational institutions to follow their dreams. Additionally, for this year 2024, the project development and implemented an interactive mobile application that educates users about the use of minerals in everyday life through four levels: Minerals in the Home, Minerals in Medicine, Minerals in Transportation, and Minerals in Agriculture. This multi-faceted approach seeks to raise awareness about the importance of mining in Peru’s economic, environmental, and social development, ultimately fostering a new generation of informed and engaged citizens who understand the vital role of mining in a sustainable future.

Feb 1, 2025

By D. R. Taylor

The use of clay granules as carriers for pesticides dates from the early 1940's and by the present day represents a business conservatively estimated at between 200 -300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: I) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By Dan Brunner, Scott Thomson, Ben Lyddall, Duncan Thomson

Geosensing is used in oilfield drilling in conjunction with geophysical tools to support characterization of rock properties, geology, and reservoir conditions. This technology is now available to the mining industry and has been successfully applied to underground in-seam directional drilling in Australian coal mines for geologic exploration and methane drainage. The system utilizes a range of drill rig and wellhead mounted sensors which, combined with analytical software, produce real-time data from which 3D spatial features can be accurately modelled significantly in advance of mining. This innovation greatly expands on the information obtained from current in-seam directional drilling practices and provides for improved characterization of coal seams, including soft and weak zones, locations of geologic discontinuities, and analysis of formation flow. This paper provides a description of the geosensing system and the interpretation of actual data from long in-seam directionally drilled methane drainage boreholes at mines in Australia, and discusses how this system increases the value of directional drilling as an exploration tool for the coal mining sector, and the evaporite and hard-rock mining sectors where directional drilling is also applied.

Feb 1, 2024