Search Documents

By R. H. T. Garnett

Recovery performance may be measured in absolute terms or in relative ones that relate the actual mining outcome to what was expected. Consideration is possible in terms of the control exercised by the operator. The eventual mineral output is the only figure known with complete certainty. The paradox is that, while performance is judged against the sampling, the reverse also applies. The R/Efactor and its four component factors are the best overall measures of performance. The choice of equipment for sampling and mining is very important. The sampling process may introduce errors and the sample density may lead to poor mining block selection. The resulting recovery performance is most visible on a regression curve. Changes in the cutoff grade must also be taken into account to avoid unrealistic production targets. Estimation methods incorporating different mathematical assumptions and techniques may cause over-or underestimation of the grade and volume. If the selective ability of the mining equipment does not match the size of the reserve blocks, the performance will be compromised. The treatment plant efficiency, the throughput rate and the degree of bedrock clean-up also affect performance. The maximization of throughput does not yield the optimum results. Marine conditions, which are outside the operator's control, affect not only operational availability but also performance. Examples are provided from actual operations for various commodities, showing the relative magnitude of the different effects upon performance.

Jan 1, 1999

By H. Huang, Y. Takasaki, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing not only because it is environmentally hazardous due to its arsenic content but also because it is refractory, causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte in Montana and Quiruvilca in Peru were spectroelectrochemically studied under alkaline conditions – pH range of 8-13 – using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after potentially cycled voltammograms in order to determine and compare surface species against theoretical EH-pH diagrams constructed from mass-balanced thermodynamic calculations using STABCAL software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs. SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of elemental sulfur suggests that copper was eventually leached from the surface. By operating above pH 12, under slightly reducing conditions near -300mV vs. SHE, arsenic can be selectively leached as thioarsenate (AsS4 3-) or thiosulfate (AsO4 3-) without sulfur formation.IntroductionEnvironmental limitations on the pyrometallurgical processing of ores and concentrates bearing arsenic and other hazardous elements often outweigh those in hydrometallurgical processing, particularly when minerals like enargite (Cu3AsS4) are present. The hydrometallurgical processing of enargite-bearing materials can be broken down into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under alkaline conditions. The selective leaching of arsenic would preferably leave behind copperrich sulfide phases, typically chalcocite (Cu2S) and covellite (CuS), which then become more amenable to conventional copper (and gold) processing. Furthermore, selective leaching often employs sulfide (S2-), bisulfide (HS-) or polysulfides (Sx 2-) to first extract the arsenic as AsS4 3- and AsS3 3- (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp et al., 2010a,b). However, hypochlorite leaching (Viñals et al., 2003; Curreli et al., 2005; Mihajlovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and finegrinding to mechanically activate the enargite surface (Balaz and Achimovicova, 2006) have been investigated to increase the normally slow reaction kinetics. Because gold ores are becoming more refractory due to increasing arsenic contents as a result of enargite, these methods are being examined more closely by the gold-mining industry."

Jan 1, 2015

By E. H. Smith

St. Joe Minerals Corp., a subsidiary of Fluor Corp., treats high-grade gold, silver, and copper ore at its El Indio plant at an altitude of 4 km in the Chilean Andes. The ore is complex, being a mixture of massive pyrite-enargite and quartz, both containing very fine gold and silver. Treatment produces a copper flotation concentrate containing high levels of gold, silver, and arsenic, and also dore bullion. Part of the flotation concentrate is roasted to remove the arsenic content, and arsenic trioxide is collected as a by-product.

Jan 1, 1987

By M. J. Ramos

Without an exclusive definition of administration in business, we could propose to define it as performance by management to adopt or implement established business formulas. Administration could also be defined as a universal process that organizes people, and achieves, through efficiency, common objectives and goals. Humanity developed some form of this process from the beginning of civilization. To imply that something is new in administration might be considered specious or naïve. Moreover, what is new in management? Administration of business is not new to the world. To prove this statement, we need only ask this question: Does the architecture and monumental workmanship of the past civilizations of ancient Egypt, Rome, and the Incas demonstrate management without administration and without definition of objectives? The answer must be a resounding ?NO!? In spite of this acknowledgment and for the purposes of this presentation, I will use the word ?new? in business and hope that the reader will follow my reasoning. The mining industry has unique characteristics in respect to other industries. It is multi-disciplinary, has a single purpose (majority for one metal), has two players (man and nature), and it involves high risks for generating environmental imbalance. Mining exploits non-renewable and finite resources, creates an unstable job market (work hard to have no work) and a speculative economic market with unpredictable prices ? a one-time payment for a finite resource with multiple recycling. On top of all that, the industry still operates within obsolete petroleum-based technology, utilizing practices that were designed two centuries ago. Today, we confront the challenges of the millennium with outmoded practices and management. Ordinarily, several styles of administration are standardized into a FRAGMENTED vertical system of organization. Mining has rigid objectives in production, with profitability as the focus from the beginning to the end. Citing the concept of safety, as an important facet of production is bombastic since, in truth, mining is an experimental industry that consistently reports high numbers of fatal accidents. In mining, we designed a process to work according to our objectives, demanding attention and supervision of all levels of management with a halo of parameters that are not assimilated into the design. We continue to perform a rigid style of management in an industry that is still not responsive to variations of the market ? losses in particular. The existing design process generates loss without capitalization and without response to said loss. This perception is reflected in a mindset that is only too ready to ignore mining liabilities. The reality of the enterprise has created an immense pressure from top to bottom in the hierarchy to do more with less. It is for all of these reasons that I propose to set forth a new essence for administration that encompasses an alternative vision and style in mining: Management by Loss. MANAGEMENT BY LOSS Management by Loss (MBL) is a systematic, integral process organized to quality control operation and the human profitability within the industry. It permits focus on achievable goals by utilizing the best practices (Mining Open-closing). Identification and characterization of loss in the process determine how objectives are defined, controlling the time limits to execute based on constant balance of mass, energy, water, and ?wastes? in each stage of the industry, in order to reach final objectives. The concept of loss can be defined by various criteria. Generally, it is the mass that could not make or arrive at its destination from a designed process or simply, it could not maintain balance. Otherwise, the design of the process describes the final point of the resource. However, those resources could not make their destination because of failure to use the best design, resources and TIME. The loss has typical characteristics such as Identifiable, classifiable, measurable, manageable, controllable, valuables, negotiable, avoidable, reportable, and monitoring. In the traditional scheme, these losses are not registered; they are made exclusions. We are trapped within a system, which was designed to obtain objectives of the industry in a specific timeframe. In the present style of administration, the focus is total - our emphasis in this treatise is in the loss. The current traditional report form contains only the most positive achievement of objectives, only the best of the exercise, humanizing numbers, without touching what we left behind or what we were waiting for to assimilate as a ?surprise account?(new account of liabilities). Management by loss is a method that redefines the concept of waste (waste zero) for controlling the mine operation under the equilibrium of the ecosystems. This method confronts the problems that impact our industry in this millennium. Understanding and quantifying losses (reserves, resources, time, energy, water, soil, materials, equipment, tasks, labor, ecosystems, etc) is a priority mandate for the industry and demands the application of a ?new ? style of administration by seeking to maintain balance instead of the disequilibrium that mining now creates in nature. It is necessary to answer questions such as: How can we minimize loss? How can the loss be assimilated during the life of the mine? What is the vision of mining in respect to the generation of waste? How can we convert liabilities into assets? In addition, the control of loss is determined in the achievement of the plan. Loss occurs because of a failure of the process in the original plan. Still we do not plan to fail but we fail to plan appropriately. It is a remarkable thing to accomplish and compel those objectives described in the original plan when that plan is designed with a determined budget. If not, we lose time and, of course, capital. Moreover, in Management by Loss (MBL), we can find answers to the following questions: What is the multiplier of productivity in mining? What are the influences of identification and characterization of loss and what is the level of efficiency of energy in order to achieve waste zero (effective cut off grade)? The challenges of mining in this millennium validate this new style of administration. Finally, it is important to point out that mining is entering into an era that has different rules, but the industry is still run by companies functioning with objectives from two centuries ago. They are trying to confront issues with concepts that are not designed for new tasks. Therefore, I ask you to consider this new style of administration of business under a vision of how the industry should be organized and managed, with an attitude of balance toward nature and social responsibility.

Jan 1, 2009

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump's best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"' BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By Mark Godfrey, Wickus Slabbert, Debra Miller, Dave Dew

Sao Bento Mlnerai;;ao Mine (SBM), located 100 kms northwest of Belo Horlzante, Brazil, was commissioned In 1987t1l to produce 185 kg per month of gold from 240 tpd of refractory sulphide flotation concentrate. The concentrate Is processed by a Sherrill Gordon design pressure oxidation circuit followed by conventional CIL gold recovery process (Flgur .. J). The original plant design foresaw expansion to 480 tpd, and In this regard the acidic effluent neutralisation, CIL and carbon circuits were designed for future expansion to treat the higher tonnage. The pressure oxidation section was sized for 240 tpd with the Intention to double the Installed plant equipment to provide 480 tpd capacity when required. This decision was based In part on the novelty of pressure oxidation to treat refractory sulphide concentrates in 1984 when the process design was finalised. General Mining, Metals & Minerals (Pty) Ltd (GENMIN), has been actively Involved for the past 30 years in the development of bacterial process for the oxidation of refractory gold concentrates; the results of this development program have provided the registered process BIOx®. The successful Implementation of BIOx® technology for treatment of refractory gold concentrates at GENMIN's Fairview Mine In October 1986t2l, as well as the substantial experience accumulated in laboratory and pilot testing of some 40 other sulphide concentrates, Justified reconsideration of the oxidation process best suited to provide the Incremental sulphide oxidation capacity planned for SBM.

Jan 1, 1992

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale), Condition C (Rolling Sandstone with Shale in Pockets) and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1978

By F. Heivilin

If the past is the key to the future, we will have ?tough? times maintaining Industrial Mineral reserves we have and proving new reserves around our plants and in new locations. The tough times will come from resources being more difficult to find, more hoops to go thru to make them Proven or Probable reserves. As always, Industrial Minerals require competitive quality, location, and costs. Since in most cases the market has suppliers, you will have to take away customers from their present supplier. This may take years or not happen even with lower cost higher quality raw materials. To determine the finished cost for a new deposit you need to design, determine capital costs, and operating costs for a new plant . Stripping, mining, hauling, processing, and transportation costs are part of the equation. After satisfying that your costs are in line you will need to do production tests to make sure the process works on the ore. You may want to complete permitting before purchasing the property. If you are new in the business you will have to prove you can deliver the right quality, the right quantity, on time consistently year after year at lower cost to take away a customer. Without being in the market this will be hard. The cut off grades to enter a market may be much lower than sale indicates because a competitor often lowers the price to keep you out of the market. We have many more items to check before the new deposits can be put on reserves. Our old reserves will require drilling to check for new products and prove that they do not contain items that would make them unusable for our product line or cause permitting problems. Archeological checks, wetlands, more water discharge testing, county zoning, and endangered species are among many items that have been added to mine permits. There will be more. A 4-6 page mining permit becomes 30-300 pages and consists of 5-15 permits, any of which might be a fatal stumbling block. It is not guaranteed that we can mine what we have on reserves. We may fight and lose. Oil-Dri?s loss in Reno and LaPort?s in England are examples where permitting failed. The NOx, sulfur, and carbon problems are just starting. Dioxin is in the background requiring monitoring on food products to Europe. What other anions, cations, endangered species, and land types are going to be problems in the future are guesses now. What new products are we going to have to test for and cause out of balance reserves? If there are none we probably won?t be here. We are competing for land use with ?Endangered Species?, wetlands, farming, forestry, cities, roads, and hunting. We?ve mined the best quality, low overburden, easiest to mine and process raw materials. The price of land and taxes are increasing. Old royalties are 2-3 times the present acre value instead of 8-10 times the property value when leased. Land taxes are up. It was and is best that we get the land in Fee Simple Title. This isn?t always possible. However, plants are closing and people have overlooked, made mistakes in drilling or interpretation of deposits. These may be opportunities. China is eating up high quality ?Industrial Minerals ?which have caused prices to rise. We may need to change our cutoffs? in terms of smaller pit sizes and higher overburden ratios. This is money in the bank. Overburden ratios and other items increasing cutoff costs need to be rethought. Suddenly doubling cutoff ratios for overburden and decreasing pit sizes are good alternatives to looking elsewhere where we might not be able to mine for a number of reasons. The higher prices make them competitive, especially when a competitor goes out of business. However, our low overburden ratios and short hauls around our plants are not safe from new roads, condemnation by county or city governments (N. J.), zoning changes (Reno, FL., CA, and environmental regulation changes (Buffers GA, MS). New roads ?Interstates? can take reserves, increase hauling distances and reduce tons per load. Let?s combine the Refractories, fullers earth, and bentonite industries and use the last 40 years as a guide to the future looking for problems and opportunities. Some or most of the following will apply to other minerals. WHERE DO WE LOOK? First, on our own properties, those next to our properties and on properties near our competitor?s plants. Where the profit margin has increased, the distance from the plant and thickness of overburden we can use is increased. The thickness of clay is decreased. For new locations we pick the ideal location and look at deposits and closed or open operations in ever increasing distances away from that location. We need to be aware of: 1. Increased transportation costs a. Access to Roads -Backhauls b. Haul with doubles and triples c. Railroads - Loading on sidings - Ability to get switches - Cars/backhauls versus rates 2. Cost of building a new plant 3. Cost of infrastructure 4. Cost of repair or new equipment when purchasing an operating or shutdown plant. 5. Local, state, and federal mine and environmental permitting. When exploring around an established operation expect that property acquisition, drilling, mining, stripping, and hauling costs will be greater due to them having second, third, or even fourth the pick of the deposits. I found this in New Jersey looking for refractories and around Quincy, Florida looking for attapulgite. You may be able to get some better properties because the operating company has angered some land owners, their drillers missed the clay, or the property wasn?t available when they were actively exploring for reserves. You may have some product lines your

Jan 1, 2009

By N. Moony

The benefit of gravity separation in improving total gold recovery in grinding circuits has been outlined in a significant number of papers to date. However, the use of batch centrifugal concentrators (BCC) as an industry standard to extract gold has limited the potential for maximizing gravity recoveries -particularly in coarse gold deposits. This is a reflection of the high upgrade ratios obtained by BCC's which has an inverse relationship with recoveries. Survey work in Australia has indicated that installation of the InLine Pressure Jig as an alternative to the Bee will significantly increase recoveries of gold by gravity and, accordingly, increase total gold recoveries and lower operating costs.

Jan 1, 1998

By K. Mohamed, G. Rashed

A conventional mechanical anchor bolt consists of a smooth bar threaded at the anchor end, with a conical wedge, and a mechanical shell anchor. When the smooth bar is torqued, the conical wedge pushes the shell anchor against the borehole wall. Coal mines use mechanical bolts in addition to other types of bolts to control the deformation and stabilize the yielded coal ribs. Limited research has been conducted to understand how a mechanical anchor performs in a coal rib. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted the study described in this paper to define the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of a mechanical rib bolt. Based on the strength of the coal seam and the conditions of the coal mines, the bolts were installed at different amounts of torque. A typical tri-linear load-deformation response was obtained from these tests. It was found that the anchorage capacity depends on the coal strength, and the anchorage stiffness depends on the installation torque. The outcome of this research provides essential data for rib support design. INTRODUCTION Rib falls are a serious hazard in underground coal mines. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Although resin bolts has been used increasingly in the last few years to control coal ribs, mechanical bolting (mainly expansion-shell bolts) is still used in many underground coal mines. Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 79% of the mines determine their rib support requirement based on the depth, mining height, and the loading conditions, of which 35% use the conventional mechanical bolts. Conventional mechanical bolts are preferable for rib support because they do not require the miners to be too close to the rib during rib bolting. Hence, using the conventional mechanical rib bolts can reduce the risk of injuries and fatalities during the installation process. The mechanical bolt or the point-anchored bolt is the oldest type of rock bolt that is still in use today. The point-anchored bolt is a tensioned bolt anchored down the hole with a mechanical expansion shell or a grouted medium (Peng and Tang, 1984). Figure 1 shows the components of the mechanical anchor bolt. The mechanical anchor bolt consists of a plug, a shell anchor, a headed smooth bar with the top end threaded, a bearing plate, a hardened washer, and sometimes a friction-reducing washer. The shell anchor can be either standard or bail type. The shell of the standard type is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the smooth bar is generally 5/8 in for the #5 bolt or 6/8 in for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the wedge down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall.

Jan 1, 2019

By Ehsan Nasiri, Keivan Pak Iman

Historically, boulders are a frequent source of problem in soft ground tunneling. It is important to attempt to make an assessment of the nature and quantity of the boulders, although in many cases, it will be impossible to do so with great accuracy. Boulders, can pose major problems for TBMs in terms of slowing down or halting the tunnel advance, cutter damage, and abrasive wear. Although proper selection of the TBM and the cutterhead can reduce the risks, ground uncertainties still cannot be eliminated. The paper reviews a case study of a 3480 mm diameter EPB-TBM in Toronto utilized for completion of 2.5 km tunnel in Glacial Till, crossing the CP railway, HWY 401, a creek, and a confined aquifer. Alignment consists of multiple horizontal curves including small radius curves (r=210 m) at shafts breakthrough. An unexpected boulder cluster lead the contractor to experience extreme damages to the screw conveyor, RFJ system and causing a crack in main motor plate which resulted in losing one of the six main motors. This paper reviews contractor’s solutions and includes discussion on specific claim resolution method used in this project that can be of great value in preparation of specification and GBR for similar projects.

Jun 13, 2021

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By Shilpa S. Haramkar, Bhaskar N. Thorat, Sachin V. Jadhav

The filtration of phosphogypsum is a ubiquitous step in the manufacturing of phosphoric acid. It is highly desired to achieve the minimum concentration of P2O5 in the phosphogypsum cake. This work is aimed at addressing P2O5 losses in phosphogypsum (PG) along with the recovery of P2O5 from slurry by using constant pressure filtration at 1 bar pressure. Laboratory tests were carried out in the phosphoric acid production plant situated in Paradeep, India. Recycled water source near acid plant (i.e., pond water) was used for cake washing to reduce the burden on fresh water stock. The findings indicated that pressure filtration offered the most effective P2O5 recovery (nearly 93.48%). The moisture was reduced to 14–16%, and watersoluble P2O5 in the gypsum cake was found to be negligible. A narrow particle size distribution was observed, which offered effective filterability with average cake resistance of 2.38 × 1010 m/kg, indicating a moderately separable cake.

Aug 23, 2023

By R. Hendrickson

In the 1940's a top blown water-cooled oxygen lance was developed to inject oxygen into liquid iron. This process, the LD or BOF process technique, today is used in 65% of the world's steel production, and represents the largest oxygen market for temperature enhancement in steel and non-ferrous smelting applications. There are three major approaches to the use of oxygen in metallurgical processes: (1) general enrichment of the air supplied to burners or tuyeres, (2) under-flame enrichment or injection, and (3) the use of an auxiliary oxy-fuel burner as a heat source. With each of these techniques there are technical and economic trade-offs.

Jan 1, 1990

By D. R. Spears

The U.S. Bureau of Mines has developed a Fast Air-injected hydrocyclone-Shallow Tank (FAST) flotation system. Conventional flotation cell kinetics are a compromise between two conflicting requirements, the need for an agitated zone for rapid bubble-particle collision, and a quiescent zone for bubble-pulp separation. The Bureau of Mines has designed a flotation system in which bubble-particle collision and bubble separation are carried out in two discreet unit operations. A bubble slurry was mixed with an ore slurry at a high rate in a modified air-injected hydrocyclone for rapid bubble-particle collision. The mixture was then fed into a unit specially designed for rapid separation of the bubbles from the pulp. A conventional flotation cell required 2.8 min to obtain 90 pet recovery at a 7-pct Cu rougher concentrate grade, whereas the FAST flotation system can obtain 85 pet recovery with a 13-pct Cu rougher concentrate grade in 0.28 min, and 92 pet recovery with a 7-pet Cu grade in 0.56 min. The Bureau's FAST flotation system is adaptable to a wider variety of flow sheets and could potentially allow for replacement of conventional flotation cells with smaller and faster units.

Jan 1, 1991

Integrated mining information and process control systems can reduce information delays, enhance decision making and improve the responsiveness of mining operations to, for example, variations in market conditions, mineral grades and ground conditions. This paper examines developments in the areas of: monitoring, data analysis and diagnosis,' communications systems; integrated mining support system;, and process and machine control. It concludes that the development of a comprehensive information technology plan is fundamental to the phased implementation of these technologies. In addition, hardware and software standards and concurrent digital design and simulation practices in selected manufacturing industries are examined and concluded to have relevance to the mining industry. Integrated information and process control systems will lead to emergence of the "digital mine". Such advances in mining information infrastructure as well as mining equipment will enable mining operations to shift from mass production methods to leaner production techniques. "Lean mining" aims to enhance and accelerate cash flow over the life of a mine by focusing on reduction of' throughput times; stockpiles for volume and quality control; and wastage and rework.

Jan 1, 1995