Search Documents

By Edwin R. (Original by) Phelps

Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining; 4) Surface mining normally recovers a- much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining [ ] methods because of geologic reasons such as the nature of the roof or bottom, thickness of the seam, multiple bedding, etc.

Jan 1, 1981

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009

By J. Kern, T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By Kenneth V. Luza

Underclays are associated with coals found in eastern Oklahoma. These coals are of bituminous rank and are in beds of Middle and Late Pennsylvanian age. They occur in an area of about 8,000 mi2, within the southern part of the Western Interior Coal Region. The rocks of the area consist of a thick series of sandstones, shales, underclays, coals, and limestones. There are more than 40 beds of bituminous coal in the state, but only 12 of these have been mined over large areas. The 12 are, from oldest to youngest: the lower Hartshorne, upper Hartshorne, McAlester (Stigler), upper McAlester, Cavanal, Rowe, Secor, Weir-Pittsburg, Mineral, Croweburg, Iron Post, and Dawson coals. None of the underclay associated with these coal beds is known to have been exploited commercially. Nine samples of underclay from beneath the Croweburg coal were collected over a wide area in the eastern Oklahoma coal field for evaluation. The underclays are usually shades of gray with brown or orange iron-oxide staining. Although soft and plastic in some places, they are generally hard and slickensided, and contain abundant carbonized plant fragments. Bulk chemical analyses, clay mineral identification, and ceramic tests were performed on each underclay sample. The dominant clay minerals are illite and kaolinite with some mixed-layer clays. Silica (Si02) ranges from 45.96% to 59.03% and alumina (Al2O3) varies from 14.98% to 23.60%. The U.S. Bureau of Mines Tuscaloosa Re- search Center conducted the ceramic evaluations. Samples were slow fired from 1,000°C to 1,250°C in 50°C intervals. Bulk density, color, percent linear shrinkage, and percent absorption were determined for each slow fire test. All Croweburg underclay samples are best suited for building brick.

Jan 1, 1999

By W. A. Hustrulid

Introduction A problem that has faced mining engineers and mining geologists for many years is how to best explore a particular prospect so that the basic decision as to whether the material present is ore or only high-grade rock can be made with some confidence. It is obvious that one could not begin a large scale mining program on the basis of tests made on a few hand samples. On the other hand, one could not be 100 percent certain as to the average grade or tonnage before beginning development, as this would require the orebody to be mined out in the sampling process. The basic objectives of the exploration program can be stated as (1) to reduce mining risk; (2) to lessen the cost of development; and (3) to increase the profits of mining. The exploration program should be terminated when these objectives are no longer being met. The construction of tunnels is a specific mining operation. In the exploration program one should gather the data needed to determine (1) the type of excavation technique(s) to be used; and (2) the rate of advance that might be expected. As in the evaluation of an orebody, with the data collected it should be possible to estimate mining costs and project life. Unfortunately, at the present time, it is not possible to do this at least when dealing with medium to hard rock types. The reason for this, it is felt, is basically the inability to identify what specific rock mass properties are of use in tunnel design and to specify how these may be obtained in an exploration program. In short, the exploration program should be designed to give information regarding both the volume (length) and 'grade' (in

Jan 1, 1997

By M. F. Dibble

Borehole mining, as a viable concept for recovering deep sedimentary mineral resources, historically has been long on promise but short on results. Application of the technology seems best suited for recovery of Miocene phosphate resources on the East Coast of the US. These deposits are potentially enormous in scope and underlie sections of the coastal plain and the near offshore continental shelf. The landside portion of these deposits is generally too deep to mine using conventional open pit methods. Recovery of these minerals requires development of alternative mining systems. A significant proportion of the offshore resources appear to occur at depths below the practical limits of cutter suction dredges and may even exceed the limits of bucket ladder dredges. In most cases, these deposits are covered by overburden that must he removed and redeposited before the mineral section can be mined. The depth, thickness, composition of overburden and environmental sensitivity of a particular location would greatly impact mining system selection. It is probable that dredging would not be an environmentally acceptable mining method in many of the areas underlain by this phosphate rock. In cases such as these, new processes such as borehole mining must be evolved or the resource will remain undeveloped. A borehole mining test program, using an existing prototype borehole system, successfully extracted Miocene phosphate in northeast Florida in 1984-1985. The top of the main mineral zone was 80 m (261 ft) below the surface. Based on the results of this test program. plus subsequent laboratory testing and engineering studies, a new prototype borehole mining system was designed in 1986. This design incorporated several innovations of offering potentially higher productivity and lower power consumption than was achieved with the previous test unit. Economic restraints at that tine prevented the actual construction and testing of this new design.

Jan 1, 1992

By H. Y. Yang, L. L. Tong

Semicontinuous-flow, multistage biooxidation experiments of a Chinese refractory, high-sulfur gold concentrate were conducted with different pulp densities for gold recovery. The maximum iron, sulfur and arsenic oxidation rates of 90.0, 88.8 and 96.4 percent, respectively, were obtained in the experiments with 5 percent pulp density. The highest gold and silver recoveries of 96.1 and 68.9 percent, respectively, were achieved by cyanidation. The negative effect of high pulp density on biooxidation was related to the decrease of free and adsorbed cell concentrations with increasing pulp density. The data of iron oxidation from the semicontinuous biooxidation experiments were best fitted by a shrinking core model in which the chemical reaction controlled the rate. The dissolution kinetics of sulfur and arsenic were therefore analyzed by a shrinking core model in which the internal diffusion controlled the bioleaching rates. For the quantitative description of biooxidation efficiency, two parameters — mass dissolution rate and volume dissolution rate — were proposed. In the first stage, the mass dissolution rates of minerals were negatively correlated while the volume dissolution rates were positively correlated with the actual pulp density. The iron and sulfur mass dissolution rates decreased with increasing actual pulp densities in the third and fourth stage, while linear increasing relationships between the volume dissolution rates of minerals and the actual pulp density were observed from the second to fourth stage. The highest mass dissolution rates of minerals were obtained in the first stage with 5 percent pulp density. The highest volume dissolution rates of minerals were obtained in the first stage with 15 percent pulp density. Compared to the volume dissolution rate, the mass dissolution rate was more intuitive to reflect the negative effect of high pulp density on biooxidation efficiency.

By R. C. Kirkman

Your interesting and well-written paper brings up the issue of the purpose or use of a mineral property appraisal, specifically the value of these evaluations when the quality and quantity of the mineral resource to be exploited have not been thoroughly investigated. I am not a practicing professional in regards to valuation of limestone investment opportunities. I simply wish to make a few generic observations about the appraisal process in order to stimulate meaningful thinking by appraisal professionals whose reports may be reviewed by professional investors and "laypersons" alike. It is my contention that the analysis given in your paper is very thorough, considering the data that was made available to you. But I would not like to be the person responsible for investment decision making without having a feel for the risk involved. Therefore, the reviewer must classify this type of analysis as relatively "subjective" because they have not received an indication of the inherent risk involved in exploiting a mineral resource. This risk can best be quantified by using probabilistic methods in conjunction with the quality and quantity of the mineral to be produced. Most appraisals passively ignore this problem. Specifically, you have accurately identified the various costs and values entering the economic appraisal process. These can usually be quantified with a great deal more certainty than the capability of the resource to provide 25 years of quality material. Also, in Cases A (West Virginia) and B (Alabama), you are fortunate enough to have previous operations data. What if there had never been production from these properties? How does a potential mineral property investor evaluate the resource capability to meet various projected financial outcomes without spending a good deal of up-front capital to drill and delineate enough quality resources for a 20-plus year operation.

Jan 1, 1990

This paper reviews the technical advice available to support companies in the delivery of social aspects of sustainable development. It will draw on diverse experience from the sparsely populated plains of the Central African Republic, one of the poorest countries in the world, to the densely populated villages of the Carpathian Mountains in Slovakia. It will review basic requirements for the consideration of social issues, as well as guidance on international best practice. It will review: the legal basis; coverage; consideration of alternatives; scope; inclusive decision-making; indicator development; impact monitoring and evaluation. The paper will discuss the breadth and depth of social issues for consideration, including the realms of responsibility of a company in terms of social development in different operating environments. The extractive industries invest substantial amounts of money which typically dwarfs local development, health or education budgets. Capacity building for local authorities is not directly the role of the company, but when understood as a strategy for risk management, it can play a vital part of sustainable development that benefits the local community and reduces the risk of social problems impacting profits. The paper will argue that social impact assessment is most effective when the outcomes are in line with a company?s principles and support core business practices. It is important that social impact assessment is viewed as an integral part of project decision-making and moves away from mistrusted PR and unsustainable philanthropy toward partnership, which finds suitable and appropriate solutions delivering ?win-win? outcomes. While development should not be seen as a direct company objective, engaging with development actors to better understand the operating context can ensure that social investment complements existing initiatives. The paper will also present different mechanisms for engaging with local actors, as well as developing successful social programmes.

Jan 1, 2007

By Dennis C. Drehmel

Because of their relatively low cost, carbonate rocks are desirable in abatement of air pollution by acid gases. Although many processes and types of equipment have been proposed to control or prevent the emission of acid gases, this paper considers only three: dry-limestone injection, wet-limestone scrubbing, and chemically active fluid beds. For the dry-limestone-injection process, surface area-especially from pores in the 0. 2- to 0.3-micron range-is one of the important parameters which will discriminate between less and more reactive carbonate rocks. Marls, chalks, oolitic calcites, and other fine- grained limestones show larger-than-average surface areas and better- than-average removal efficiencies. Inert chemical impurities such as silica detract from reactivity. A dolomite is not necessarily less re- active than a calcite. For the wet-limestone-scrubbing process, dissolution rate of the carbonate rock controls the differences in stone reactivity. In this process the dolomites are less reactive than the calcites. In addition, more than 90 percent of the dolomitic impurity in Fredonia white lime- stone is inert during limestone scrubbing. Dissolution rate is also a function of particle size for large-grained carbonate rocks. Fine grinding of such rocks will increase the dissolution rate to that of a fine-grained rock. Hence the requirement of high dissolution rates may be met by some grinding of fine-grained material (e. g., marl, chalk, or other limestone) or by fine grinding of coarser grained material. For chemically active fluid beds, chalks have the best capacity to absorb both SO2 and H2S. However, most chalks are probably unsuitable for fluid beds because of high attrition rates. Because dolomites are generally more reactive than calcites with both SO2 and H2S, a dolomite would be the feed material of choice for a chemically active fluid bed.

Jan 1, 1974

By Howard S. Avery

The wear resistance of an alloy in heavy mill liner sections may be quite different from that of the same alloy in small balls and other light sections. This fact was established by means of a well standardized laboratory test that was validated for ball mill service. The salient properties of mill liner alloys, including austenitic manganese steels, medium alloy hardenable steels, and abrasion resistance cast irons are described, critically compared, and quantitatively ranked in terms of mill liner service. Where they are tough enough the high-chromium and other martensitic cast irons (e.g. Ni-Hard) promise maximum economy, but their section sensitivity is a limitation. To overcome this an extensive research program studied over a hundred experimental alloys, ranking them for heavy section abrasion resistance by means of the laboratory test. Computer analysis of the results provided a parabolic formula in terms of composition, the apexes of the parabolas providing optimum wear resistance. From the extensive family of parabolas one apex was selected for intensive study in experimental liners, pilot plant production, development of quality controls, and finally full scale production. This is a 19% chromium iron critically alloyed with nickel and molybdenum and hardened by heat treatment. It has excellent resistance to various types of abrasion, but its chief advantage is in heavy mill liner sections, where it has about 25% better abrasion resistance than the best of the quality controlled chilled Ni-Hards. It is also tougher. After production problems were solved, a number of ball and rod mill tests were arranged on a guaranteed performance basis. Two of these, representing about 138,000 pounds of mill liner castings, have recently confirmed in service the superiority that was predicted by the laboratory tests.

Jan 1, 1969

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 11, 2018

By Harvey W. Parker

Our industry has developed to the skilled, experienced and productive industry that we now enjoy as a result of the visions of great engineers throughout history, but, in particular for their visions in the last 1 centuries. Unfortunately for our forefathers, the technology lagged so far behind that these exceptional visions could not be realized for decades, sometimes for a century. All that has changed in recent time and many bold and visionary projects can now be constructed and operated because of dramatic advances in technology. Before, say, 1950, tunnel technology developed very slowly. However, technology is now developing at such a fast rate that planners and decision makers are challenged to stay ahead. Moreover, new technology will develop during the lifetime of any project that can dramatically improve under-ground space projects. One of the best examples of this technological advancement is that of closed-face TBMs which now make tunneling feasible in previously impossible ground conditions. Since it usually takes a decade or more to plan, overcome environmental and political issues, construct, and put into service major projects, planners and designers are challenged by the changes in technology that occurs during the long time span of planning and construction. This is particularly true of large infrastructure projects such as transportation, water and wastewater systems and other major underground schemes. Also, since the serviceable life of many of these tunnels is often over one century, planners must consider not only lessons learned from the past but also what new concepts and innovations may develop over an extremely long time. These and other issues create a great challenge to planners and illustrate the great importance of careful but creative vision and flexibility during planning of long-term tunnel and underground space projects.

Jan 1, 2008

By T. Yegulalp, M. Castaldi

As global energy demands increase, there will be a critical need to employ fuels that have minimal environmental impacts. While hydrogen is considered the ultimate fuel for that purpose, hydrocarbon based fuels will be in use for a considerable time and will probably be the first major source of hydrogen for next generation power systems. The best fuel for this transition will be natural gas because of the high hydrogen to carbon ratio. Natural gas hydrates have the potential to meet the global energy needs for the foreseeable future. The amount of energy stored in natural gas hydrates is significantly more than that of all the other fossil fuels combined. However, most proposed techniques for recovering the natural gas from the hydrate require too much energy input, raise safety concerns or can only recover a fraction of the gas. This paper discusses the technical feasibility of a novel method of gas production in hydrate reservoirs. The method is an in-situ process that creates a point heat source in the hydrate formation. This method not only significantly reduces the energy input, but also has the potential to sequester as much or more CO2 than would be produced from combustion of the natural gas produced, thus making this in-situ methane production technique virtually carbon neutral. Simulations using FEMLAB™ show that the method offers an energy efficient and environmentally friendly way to produce natural gas from hydrate reservoirs. Preliminary results indicate that it is possible to have an energy efficiency of nearly 90% for land based reservoirs for hydrate loadings of 20%. The simulation results also suggest that alternatives to a point source can be employed which may improve the process efficiency.

Jan 1, 2007

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By David Wright, Colin Burns

Successful leaching of gold depends on appropriate chemical conditions; contact between leach solution and the gold particles; separation of the leach solution from the solids and extraction of the valuable ion from the solution. Irrespective of the leaching method employed the chemical conditions required are similar as is the dependence of solu­tion/gold contact on liberation. The various leaching methods available vary in the means by which gold/solution contact and solid/liquid separation are achieved. The essential difference between heap or vat leaching techniques and those involving agitation of a slurry is dependence on percolation for effective gold/solution contact. The most significant factor preventing uniform percolation is the presence of fines or clays. The quantity and character of the fines fraction is ore type dependent and may result from crushing, degradation during stacking or leaching, or the natural size distribution of the ore. The problems associated with fines can be aggravated during stacking and preparation of the heap. Segregation during stacking can result in concentration of fine particles at the centre of heaps. Further concentration of fines may also occur during irrigation by the movement of the fine particles with the solution. The end result is that the areas in which fines are concentrated become areas of low permeability. The contact between leach solution and the ore in such areas is, at best, slowed down dramatically and, in some cases, prevented altogether. The consequences of this phenomena are slow leaching and a reduction in recovery. The conventional solution to this problem is well known. Agglomeration of ore prior to heap leaching is practised widely. The effect of agglomeration is to immobilise the fines by causing them to adhere either to each other or to larger ore particles. The net effect is that the ore behaves as if no fines were present. The use of agglomeration is limited only by its cost, the most significant components of which are the cost of binding agent, commonly cement, and the capital cost of the agglomerating equipment.

Jan 1, 1995

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.