Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Variations of cut-and-fill stoping are the most com¬monly used methods for mining narrow, nearly vertical veins in the United States. These methods offer the best results for maximum recovery with minimum dilution of ore from veins that are irregular along either the strike or dip. The vein is developed along the strike length in 61 to 122-m (200 to 400-ft) blocks or stopes and vertical lifts of 48 to 61 m (160 to 200 ft). The level development is either on the vein or parallel to the vein with crosscuts intersecting the vein at right angles. Chutes, manways, and haulageways are established in the center of the stopes at the lower level of the ore block. Mining then proceeds by blasting down horizon¬tal cuts of the vein in both directions from the chutes. As the blasting continues to the outer limits of the stope, the broken ore is slushed into chutes. When a complete horizontal cut has been made, the service raise, including chutes, is raised to a height of a few feet from the back and the stope is filled with either sand fill or waste rock. Then the mining cycle is re¬peated until the stope reaches the level above. LEVEL DEVELOPMENT PRACTICES FOROVERHAND CUT-AND-FILL STOPING The two basic methods used are: the development of the haulage drift within the vein, or development of the haulage drift paralleling the vein in the foot or hang¬ing wall with crosscuts intersecting the vein perpendicu¬larly at 61 to 122-m (200 to 400-ft) intervals. The il¬lustrated methods of development show some of the variations which can be used to develop a stope block. Development for cut-and-fill stoping does not require the more elaborate schemes outlined for shrinkage or sublevel long-hole stoping. Many factors must be considered before deciding on a particular development plan and usually the nature of the vein or host rock will dictate which specific method to use. If the vein is relatively straight, then develop¬ment on the vein is feasible. Excessive ground pressures will necessitate the leaving of a sill pillar (Fig. la) and highly fractured or "heavy" ground will require timber¬ing (Fig. 1b). Development on the vein has the advan¬tage of reducing capital outlay and waste handling prob¬lems since the mined rock has value. But removal of the sill pillar is costly and time-consuming. Also, where no sill pillar is left, excessive timbering and subsequent level repair is a drawback. Development in either the footwall or hanging wall is the more common procedure and offers greater flexi¬bility in overall development of consecutive stoping blocks by partially disassociating the level development from stoping (Fig. 2). Chutes, manways, and service compartments com¬prise the next stage of development and are established in a variety of ways. They provide access to the stope, ventilation ducts, and muck removal. Several different development systems are in common use and average costs for each have been developed. Raise borers are used to establish ventilation and ac¬cess from level to level. They are normally reamed with 1.5 or 1.8-m (5 or 6-ft) cutterhead and may either be left bald or lined with a 1.2-m (4-ft) diam corrugated liner plate, depending upon ground conditions. The use of an Alimak raise climber is another effec¬tive method of driving a raise from level to level. The size usually is 2 m (7 ft) square. This will accommodate square-set timber which is later installed. This method of raising is not common, although it is a valuable tech¬nique especially when level spacing is several hundred feet.

Jan 1, 1982

By Leonard G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups: that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mm) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh (< 0.60 mm); in fluidized bed uses, the coal is typically < 8, in. (< 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1 to 2% in. (25 to 63 mm). Coal preparation plants typically work with a coarse size fraction of 6X 1/14 in. (150X32 mm). The past decades has shown a steady increase in the tonnage of coal cleaned, 1 but it seems probable that the next decades will produce much wider applica- tion of deep coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is intimately connected with the size of coal, a systems design engineer will need as much information as possible concerning the size distributions produced by different types of machines and how these can be modified by different ways of operating the machines. In general, the following questions will be of concern: 1.What type of crusher or grinder is best, or most satisfactory, for reducing a given feed size and type of coal to a desired product size? Frequently, the desired product is smaller than some nominal size, but with as few fines as possible, or the fraction in some size range has to be as high as possible. 2. How big does the machine have to be for a given throughput rate? 3. How much electrical energy (or its equivalent) is required per ton of product? 4. How does the size distribution vary with change in throughput rate, and is a control scheme necessary or desirable? 5. Can the size distribution be readily varied if desired? 6. What is the optimum way to operate a machine in a given system? This section will emphasize certain general principles which guide us in answering these questions. PARTICLE SIZING Since particle size and size distribution are the raw information with which we work, it is worthwhile to review the terminology used. In this regard, see

Jan 1, 1991

By Gary Beerkirkcher

INTRODUCTION The mine hoisting equipment that is selected and installed at a mine is for the lifetime of the mine and, therefore, it is extremely important that a proper choice be made. Several types of mine hoist designs, including double drum hoists, single drum hoists, friction hoists, and various special designs of these, are available to¬day. Each has advantages and disadvantages and they should only be used in suitable applications. Drive systems for mine hoists must be evaluated together with the mechanical systems for each hoist application. It does not make sense to properly select the hoist mechanical system and then choose a drive system that turns out to be a bottleneck. MINE HOIST TYPES There are two basic types of mine hoists available in the world today: the drum hoist, on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe) hoist, which merely passes the rope over the wheel during the hoisting process. Drum Hoists Single Drum Hoist: A single drum hoist (shown diagrammatically in Fig. 1) can be used as a service or production hoist with the cage or skip in balance with a counterweight (Figs. 2 and 3). It can efficiently service one or more levels, since the location of the counterweight at any time is not important. As a pro¬duction hoist with skips in balance, the single drum hoist is best used for single level hoisting. All rope adjustments for proper spotting must be done manually for the single drum hoist. This has to be done periodi¬cally to compensate for rope stretch. A variation of the single drum hoist is the divided drum hoist. If multilayer winding is necessary, the single drum hoist must have a divider to allow a sep¬arate compartment for each rope. If a counterweight is used with a divided drum application, the counter¬ weight rope can be wound on a smaller diameter (Fig. 4). Consequently, it moves a lesser distance than the main conveyance and rope adjustment problems are re¬duced. Double Drum Hoist: A double drum hoist in oper¬ation is shown in Fig. 5. Double Drum Hoist With One Drum Clutched: As a service hoist with cage and counterweight, a double drum hoist with one drum clutched (Fig. 6) can serve several levels efficiently. The advantage of having the clutched drum is that it allows rapid adjustment of ropes due to initial stretch. Some users may prefer the single drum hoist with manual rope adjustment, while others consider the added expense of the second drum and clutch is justified to make rope adjustments quickly. The value of this feature for a particular application should be discussed with the hoist manufacturer. As a production hoist with skips in balance for a multi¬level operation, the clutch can be adjusted for efficient hoisting from any level. Double Drum Hoists with Both Drums Clutched: There are also double drum hoists that have both drums clutched (Fig. 7). The main advantage claimed for this type of hoist is that if something happens in one of the two compartments, the hoist can operate in the other compartment to raise and lower men and sup¬plies. This feature is particularly favorable if there is only one shaft entrance to the mine. Multiple Drum Hoist: The multiple drum hoist, a South African innovation, is a type of drum hoist about which everyone should be aware. Basically, it uses two hoist ropes per conveyance which at great depths per¬mits use of smaller ropes and smaller drums. There are none in use in the United States today. However, they should be considered in very deep mines. Friction (Koepe) Hoists This hoist (Fig. 8) was introduced to the mining world by Frederick Koepe in 1877. The basic prin¬ciple of the friction hoist is that the hoist rope passing

Jan 1, 1982

By Charles T. Steuart, Richard B. Berg

Tripoli and the related mineral commodities such as micro- crystalline silica have been mined for more than 100 years for their abrasive properties. Although abrasive and buffing compound markets are still very important, within the last 15 years the filler and extender markets in paint, plastics, rubber, adhesives, and sealants have increased substantially. Tripoli or microcrystalline silica consists almost entirely of very small quartz crystals, many less than one micrometer in length. Material mined from different districts differs in crystal shape, grain size, and texture of the rock, all of which influence markets. Most US deposits are now mined by surface methods, and both air floated and micronized products are marketed. Deposits of tripoli now mined in the United States occur in chert-bearing Paleozoic limestone in the central part of the country with producing districts in southern Illinois, central Arkansas, and eastern Oklahoma. Although deposits within each district are confined to specific formations and extend laterally within those formations, individual bodies form minable deposits that are typically several hectares in areal extent. Tripoli is white to cream to rose and characterized by high porosity and ease of disaggregation. DEFINITIONS Tripoli In the United States, tripoli was first used to describe the fine-grained, easily disaggregated material from Seneca, MO, be- cause of its similarity to a rock from the Tripoli region of North Africa (Hovey, 1894). The North African rock is actually diatomaceous earth, a material that is similar in appearance to the rock from Seneca, but is of entirely different origin having formed by the accumulation of siliceous remains of microscopic marine or fresh- water animals. Tripoli is best defined as a very fine-grained, generally porous rock that consists of microcrystalline quartz, typically formed by the alteration of a chert-bearing limestone. Tripolite A term used to describe a rock from the vicinity of Tripoli in North Africa which is diatomaceous earth (Quirk and Bates, 1978) Microcrystalline Silica Microcrystalline silica is the same material as tripoli, but the distinction between the use of these two names is dictated largely by convention and markets. Material produced from southern I1linois deposits and used in white pigment and filler applications is generally referred to as microcrystalline silica, whereas that used in abrasive applications, both from the Illinois district and from other states, is commonly called tripoli. Amorphous Silica Amorphous silica, a term formerly used to describe the material produced from the deposits in southern Illinois, is now replaced by the term microcrystalline silica. Amorphous silica came into use when even optical methods for the identification of very fine- grained quartz were not widely available and the Illinois product, composed of quartz grains too small to be seen with the unaided eye, was thought to consist of amorphous silica. The Illinois material is clearly crystalline quartz, as shown by X-ray diffraction analysis and scanning electron microscopy (Fig. 1). Novaculite Although originally used to describe a rock suitable for the manufacture of whetstones, novaculite is now defined more generally " - as a homogeneous, mostly white or light colored rock, translucent on thin edges, with a waxy or dull luster, and almost entirely composed of microcrystalline quartz" (Steuart et al., 1983). The more compact rock mined in central Arkansas from the Arkansas Novaculite is referred to as novaculite, whereas the more porous rock is referred to as tripoli. Rottenstone The commodity rottenstone is sometimes included within the general mineral commodity category of tripoli. Rottenstone is mined in Northumberland County in eastern Pennsvlvania and formed by the weathering of a siliceous shale of Devonian age (Faill, 1979, Berkheiser, private communication, 1991). This material is used as a filler and extender, but is apparently unlike tripoli both in origin and physical properties. Spiculite Spiculite is a rock consisting of siliceous sponge spicules having formed by the removal by solution of the carbonate matrix of a spicule-bearing limestone. Spiculite has been mined in Texas and, because it resembles tripoli in several aspects, is included in the discussion of deposits.

Jan 1, 1994

By H. O. Seigel, John C. Robbins

Luminex is a new method of prospecting for mineral deposits based on time-resolved mineral luminescence created by an ultra-violet light source. Developed by Scintrex Ltd., Luminex detects and resolves a group of key minerals - either ore minerals themselves or, more often, accessory or pathfinder minerals for certain types of economic ore deposits. These minerals are commonly found on the earth&apos;s surface, even in areas of considerable weathering. The method extends the range of mineral deposits that are remotely detectable from the air. Tungsten, tin, molybdenum, gold, and bedded lead-zinc deposits are included. Therefore, Luminex is a natural supplement to the three classical methods of airborne geophysics. The luminescence of minerals has been known and used qualitatively in mineral exploration for many years. But there are more than 500 minerals known to be at least sometimes luminescent. Luminescence of most is unpredictable and the colors they emit may vary from locale to locale. It is, perhaps, this apparent complexity of the field that has discouraged its proper scientific scale until now. There are two basic types of luminescent minerals - intrinsic and impurity activated. In the first type, luminescence is an inherent property of the mineral in its purest form. In the latter, luminescence is due to the introduction of foreign trace elements, often in very modest amounts (ppm), into the crystal lattice. These trace elements are known as activators. There are very few intrinsic luminescent minerals commonly found in nature. Chief among these are the calcium tungstatemolybdate family, more commonly known as the scheelite-powellite family, and the uranyl minerals such as autunite and saleeite. The vast majority of other known fluorescent minerals such as fluorite, hydrozincite, and many calcites, are impurity activated - that is, they will not fluoresce in purest form. In addition to the many minerals likely to luminesce at the earth&apos;s surface under ultraviolet excitation, any prospector who has ventured out at night with a mercury lamp will know that much organic matter luminesces - for example lichens and even scorpions. Just as the eye finds difficulty in resolving the luminescence of minerals from that of organic materials, it also has its limitations at sorting out minerals from one another by their luminescent colors. Figure 1 shows, in part, the photoluminescent emission spectra of scheelite, hydrozincite, and autunite. It is clear that there is a considerable similarity in spectrum between scheelite and hydrozincite and a great deal of overlap. In fact, a small amount of molybdenum in the scheelite lattice can almost bring these two spectra into coincidence. On the other hand, the autunite emission spectrum is clearly resolved from the other two. Basis of the Method The right-hand side of Fig. 1 shows the time waveforms of decay of the photoluminescence of the same three minerals. It is apparent that the lifetimes of photoluminescence of scheelite and hydrozincite are radically different and that these two minerals, therefore, may be readily resolved through their emission lifetime characteristics. It is in the realm of time-resolved measurements (lifetime characteristics) that Scintrex has made its major advance in the Luminex method. With the exception of some work by Exxon confined to uranyl minerals, to the best of our knowledge, no systematic scientific investigation has been carried out in the field of time-resolved mineral luminescence studies other than the work of Scintrex. Scintrex&apos;s findings are that all organic materials and most commonly activated luminescent minerals have lifetimes shorter than one microsecond. In addition, only a relatively small number of minerals - among them those called key minerals, or certain ore and pathfinder minerals - have lifetimes greater than one micro-second. Scintrex is able to characterize these minerals primarily by their emission lifetimes and secondarily by their emission spectral characteristics. By a combination of these factors a mineral index is arrived at. From that, photoluminescent minerals can be resolved from one another with a high degree of probability. At least two spectral channels and two time channels - of which one can be common - are required to apply this mineral index. Ground System A portable hand-held Luminex analyzer based on a modulated mercury lamp has been used to date in Canada, the US, and Australia. The current production model of this device is the LG-2. It has two spectral channels and two time channels for each spectral channel. Figure 2 shows a ground Luminex traverse over the Texas-Arizona zinc prospect in Arizona. The instrument was set so the channel read was hydrozincite-specific insofar as possible. The mineralization in this prospect is known to be hydrozincite and other zinc secondary minerals in limestone. Figure 3 shows a ground Luminex traverse over the AAA uranium prospect in Nevada. The instrument was set to optimize the uranyl response. For comparative purposes, broadband scintillation counter readings were made on the same stations (also shown in Fig. 3). It is apparent that both the Luminex and the scintillation counter results reflect a near-surface distribution of uranyl minerals. It is interesting that no visible uranyl secondary minerals

Jan 7, 1983

By Kerry M. Masson

Perhaps the hottest item on the agendas of most state legislators this year is the state budget. The main question: Where will all the dollars come from to finance health care programs, state jobs, unemployment compensation programs, and on and on? This is especially so since people are out of work, business bankruptcies are up, sales are down, and incoming revenues from some sources have decreased or dried up. A sure bet is that state taxes will be increased in some form or another. The mining industry could face increased income taxes, property taxes, severance taxes, or even a host of new taxes (if the state does not already have them) like a gross receipts tax, investment tax, or tax on revenues made outside state borders. That&apos;s bad news for an already depressed industry, even though increased taxes may be the least of the industry&apos;s worries in the current economic climate. While reopening existing mines and developing most new mineral projects depends primarily on higher commodity prices, new taxes still could pose long term concerns for mine project development. Just how mineral tax law impacts a project is not easy to figure. It involves a complex set of calculations based on interpretations of numerous federal, state, and local tax laws that change almost annually. At best, projections of tax effects for the life of a mine are educated guesses. At the same time, projections are necessary to evaluate the economic feasibility of a mineral project. At a recent Technology Transfer Seminar, the US Bureau of Mines introduced a computer software program designed to evaluate the feasibility of a mineral project and to determine the tax effects on the project&apos;s discounted cash flow rate of return (DCFROR). The program, called MINSIM, began in 1967 as a 200-statement FORTRAN II program for evaluating a hypothetical large-scale open-pit gold mine. This single-commodity oriented program employed discrete simulation techniques and a continuous DCFROR was used to measure the effect of changes in revenues and costs. Over the past 15 years, MINSIM has developed into a program 70 to 100 times larger than the original. Basically, it will analyze costs and parameters specific to an identified deposit, then determine the DCFROR. Or by using a specified DCFROR, it will determine the primary commodity price required to attain that specified rate of return. MINSIM, which is explained in detail in this article, is available from the Division of Minerals Availability, USBM free of charge. Written in FORTRAN IV, it comes on punch cards or magnetic tape and is compatible with most major computer systems. The MINSIM Program The main objective of any freeenterprise mining venture is to make a profit. To determine profitability of a given project, alternate methods of operating and financing must be evaluated. That is the purpose of MINSIM. While there are a number of methods of evaluating the economic profitability of a mining project, MINSIM uses the Discounted Cash Flow Rate of Return (DCFROR) method as its major criterion because DCFROR considers the time value of money and gives the truest measure of profitability. One disadvantage is that the calculations are deposit oriented. In other words, MINSIM analyzes only those costs and parameters specific to the deposit. It cannot be used to evaluate the overall corporate picture. The program is designed to simultaneously handle five different commodities and a leach operation for any type of mining project. For example, analysis of a coal project would include only one commodity-coal at the mine mouth. Analysis of a copper operation might include numerous commodities-from the raw material to the refined product. Input MINSIM considers capital investment-recoverable exploration, acquisition, and development costs; depreciable capital investments such as mine plant and equipment, mill plant and equipment, and infrastructure costs; all general and commodity specific operating costs; and the cost of alternate financing methods. The program has the capacity to incorporate different types of depletion allowances, numerous commodity-dependent severance taxes, variations of property taxes, and many methods for calculating state or provincial taxes. There are even many different ways to calculate federal and national taxes. The capacity to handle tax variations is generated from an internal subroutine in the program called the "open file." The user can reconstruct, customize, or evaluate any kind of tax desired. Outputs Given this kind of capacity for numerous input parameters, MINSIM is capable of the follow¬ing major outputs:

Jan 3, 1983

By A. J. Kroha, N. Wesis

Most copper mines produce both ore and low-grade "leach" rock or acid waters that contain recoverable copper. The sulfide ores pre¬dominate, and a portion that is too low grade for milling to produce concentrates for smelting, but has to be mined and trucked away anyhow, may be leached successfully with acid in dumps. Most of this leach material consists of sulfides and silicates or carbonates, and if the gangue is such that it consumes a high quantity of acid, this factor may rule out a leach operation. There are also valuable deposits that contain mostly acid-soluble copper, or occasional sulfide ores from which a sulfide concentrate can be roasted and acid-leached to produce a copper-bearing solution. Finally, there are milling ores in which the lesser part of the copper is acid-soluble and can be precipitated with iron or synthetic inorganic precipitants that produce metallic copper or copper sulfides that will float with the sulfides. Ordinarily, ores that contain copper associated with the sulfur ion, such as in the minerals chalcopyrite, chalcocite, bornite (and others), are milled to produce a 25-30% Cu concentrate for smelting, while a lesser amount of acid-soluble copper may be converted from solution to cement copper on iron scrap. A fast-growing percentage of such copper, however, is removed from solution with exchange resins or organic compounds in organic carriers such as kerosene (solvent extraction), then eluted with strong acid and subjected to electrolytic precipitation either in marketable form or as anodes that can be refined further. From the point of view of conventional copper smelting, copper flotation concentrates and cement copper are of chief interest in this chapter. Table I is a condensed open schedule for concentrates that generally run between 25 and 35% copper, and much less frequently as low as 12-15% or as high as 65-75% copper, the former being due to intimate relationship with pyrite (like the former United Verde Extension), and the latter representing such ores as the Bolivian Coro¬coro ore in which the copper is in the form of chalcocite in sandstone. These extremes are no longer common. When they occur, a special purchase schedule has to be negotiated. Included in Table 1, copper precipitates (cement copper) generally run from 70-85%a copper, and the same basic purchase schedule is used as with flotation concentrates. Sulfide Flotation Concentrates The sulfide copper concentrate produced in the mill as a flotation froth, with water then added for transportation of the heavy mineral particles from the flotation cells to thickeners, may run 60-80% water by weight, and the removal of water down to 25-50% by weight by means of thickeners, followed by further dewatering by continuous vacuum filters to 7-18% moisture by weight (depending on size of solids by screen analysis and also by content of clay) is a critical operation. Mill operators would like to produce a filter cake with 7-9% moisture content, but even with the help of steam on the filter this desirable condition is seldom realized when the concentrate is as fine as 80% -325 mesh. More commonly, the final concentrate is reground in pro- to produce best copper recovery and grade of concentrate (or molybdenite separation). In those cases, increasingly frequent, the filter product may not be a cake at all, but a mud that is hard to handle-even requiring a thermal dryer. Greater difficulty of form¬ing a manageable cake often comes from the copper-molybdenum separation by flotation, because the alkaline sulfides and hydrosulfides, or cyanide, or other similar reagents used for the separation, may leave the now relatively molybdenite-free copper concentrate even more difficult to filter. Handling a wet filter cake is difficult enough when its destination is only a short distance away-a matter of yards rather than miles. In those cases the filter cake may be thermally dried near the point of production, using rotary or multiple hearth, or fluidized-bed dryers. Alternatively, the concentrate may be pumped or carried in slurry form to the smelter and filtered there, or it may be spray-dried and compacted. For transportation to a smelter just a few miles to a few thousand miles away by ship or railroad other factors may be important, such as: in shipping by sea, avoidance of spontaneous combustion; in shipping by rail, losses by leakage if too wet or by wind and sun if too dry. It is the responsibility of the millman-usually the mill superinten¬dent-to make sure that his concentrates are in satisfactory condition when they leave the mill so that they meet these requirements: 1) They must have been accurately sampled and dry-weighed, the latter meaning that a moisture determination and gross weight must have been taken. 2) They must be dried sufficiently when necessary to prepare them for safe transportation. 3) They must arrive at the smelter with reasonable likelihood that they can be check-weighed and sampled fairly and equitably,

Jan 1, 1985

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985

By Alan K. Burton

Massive increases in the productive capability of open pit nines after World. War II were in a large part made possible by the introduction of ever larger trucks and the supply of a seemingly bottomless ocean of inexpensive and readily accessible oil. Over a period of about 25 years, a variety of technological developments permitted a tenfold truck payload increase, from about 32 tonnes (35 tons) to 320 tonnes (350 tons). There is no, doubt that this was a remarkable achievement resulting in impressive benefits of scale as well as the ability to control what would otherwise have become an intolerable traffic congestion problem in today&apos;s large open pit mines. It became fashionable and economically possible during this time to mine large quantities of low grade material and to tolerate very high stripping ratios. As tine has gone by and as easier to get at and higher grade deposits have been depleted, ore grades have tended to decline while stripping ratios have increased. The alternative to reduced revenues has been an ever increasing demand to step up production which in turn has led to a continuing demand for ever larger and larger trucks. While a larger truck has had the effect of reducing the cost of the operator per unit of material moved and of reducing traffic congestion, it has not specifically addressed the subject of fuel cost.

Jan 1, 1981

By M. J. Meulendyke

Within the mineral processing Industry. a range of grinding conditions exists which include semi-autogenous grinding (SAG), rod milling. and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1989

By M. R. Yalamanchili, J. D. Miller

Discussion by M.R. Yalamanchili and J.D. Miller The authors, M. S. Celik et al., should be recognized for their efforts to describe the flotation behavior of boron minerals. In the case of borax and other soluble salt minerals, analysis of the flotation chemistry has been difficult because of the high ionic strengths associated with these soluble salt systems. However, considerable progress has been made in this area, and recently a surface charge/collector colloid adsorption model was proposed by Miller and his coworkers to explain the collector adsorption phenomena observed in soluble salt flotation systems (Milleret al, 1992; Yalamanchili et al., 1993; Miller and Yalamanchili, 1994; Yalamanchili and Miller, 1994a: Yalamanchili and Miller, 1994b). In this work, the sign of the surface charge of alkali halides in their saturated brines was established on the basis of nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis (Miller et al., 1992). Generally, these results are what would be expected from the simplified lattice-ionhydration theory. This electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble salt flotation systems indicates that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation/bubble attachment results for 21 different alkali halides (Yalamanchili et al., 1993; Yalamanchili and Miller, I994b) confirmed that the flotation response of soluble salt minerals with weak electrolyte collectors can best be explained by the adsorption of oppositely charged collector colloids rather than by the adsorption collector ions and/or neutral molecular dipoles as originally suggested by many researchers (Fuerstenau and Fuerstenau, 1957; Schubert, 1967; Roman et al., 1968). In addition, the flotation of certain alkali oxyanions (Pizarro et al., 1993) and double salts such as schoenite and kainite can be explained by the same collector colloid adsorption mechanism (Miller and Yalamanchili, 1994). The borax flotation results reported by Celik et al. need to be examined in terms of the above mentioned surface charge/ collector colloid adsorption model. Unfortunately, the authors seem to be unaware of this recent work that nicely describes soluble salt flotation with weak electrolyte type collectors such as amines and carboxylates. In view of our past work, the flotation characteristics of borax were of particular interest, and, in this regard, the results of dodecyl amine flotation of borax reported by Celik et al. have been examined in further detail in the light of experimental results from our laboratory. In our research, a vacuum flotation technique was used to study the flotation response of borax (Na2B407.10H20), which has a solubility of 39 g/L at 25 °C) with dodecyl amine hydrochloride as collector. These chemicals were purchased from Eastman Kodak and used as received. Saturated solutions of borax at desired pH values were prepared by continuously stirring the salt solutions over a period of about 10 hrs. It should be mentioned that the conditioning time to achieve equilibrium is an important variable and can significantly change the flotation response of some soluble salts (Yalamanchili et al., 1993). Collector was added to the saturated borax solutions containing about one gram of 100x 150 mesh borax particles, and conditioning was done for about 20 minutes prior to flotation. The borax flotation recoveries from saturated brine are presented in Fig. 1 as a function of collector addition at the natural pH of 9.3, as reported both by Celik et al. and as measured in our laboratory. In addition, the region of precipitation for the dodecyl amine hydroborate is included in Fig. 1. It can be seen in Fig. 1 that the flotation response curves are separated by about one order of magnitude in R12NH3CI collector addition. The flotation results of Celik et al. show that the maximum borax recoveries can be obtained below the solubility limit of the dodecyl amine hydroborate collector. However, in our experiments borax flotation seems to occur only after the precipitation of the dodecyl amine hydroborate collector as might be expected from the collector colloid adsorption model (Yalamanchili et al., 1993) if borax were negatively charged. Further analysis by nonequilibrium and equilibrium electrophoretic mobility measurements for borax indicates that borax is negatively charged at the natural pH of 9.3, as discussed below. The reliability of the nonequilibrium electrophoretic measurements has been demonstrated previously for alkali halides and alkali oxyanions (Miller et al., 1992; Miller and Yalamanchili, 1994). The equilibrium and nonequlibrium electrophoretic measurements for borax were found to be consistent and are presented in Table 1. These results provide clear evidence that borax carries a negative surface charge in its saturated brine (pH 9.3), and the sign of the surface charge of borax reverses and becomes positive if the pH is reduced to 8.6. The equilibrium between borax and its saturated brine can be described by the following reaction: [2Na2B407.1OH2O-4Na++B407=+HB4O7 +OH+19H20] It appears that the oxyanions of the borax lattice provide

Jan 1, 1995

By A. J. Richardson

Before the development of the underground stoping and mining costs can be considered, certain facts about the ore body, the proposed mine, markets, etc., must be known or determined. In the case to be studied, the zinc-lead mineralization occurred with a narrow vertically dipping structure of undetermined length and vertical extent. Exploration completed to date has revealed 6.5 mil¬lion st t of proven reserves. A further 820,000 st of in¬dicated reserves has been outlined and this tonnage is considered capable of being expanded by a factor of approximately four after more detailed drilling. After studying the market conditions and completing a very preliminary feasibility study, it was decided that production would be 730,000 stpy (or 2000 stpd) of ore. First year production would be at the rate of 1500 stpd. The main design criteria for the selection of the min¬ing methods are minimizing surface subsidence, maxi¬mum recovery of the ore body, maximum degree of grade control, maximum productivity, and safe working conditions. Two basic extraction systems are considered capable of meeting these requirements: mechanized cut¬and-fill stoping and sublevel long-hole stoping with filling. The primary development system of the mine has been designed to give maximum flexibility in stoping systems and layout and to permit changes if considered necessary as a consequence of actual production ex¬perience. At the present time, access to the mine is by a circu¬lar concrete lined vertical shaft, 16 ft diam, sunk to a depth of 1380 ft. Two exploration levels have been driven within the ore zone at depths of 165 and 1246 ft below the surface outcrop. The development to date had the objective of sampling the mineralization and produc¬ing detailed information on the outline of the ore body and the distribution and controls of zinc and lead values. In an attempt to satisfy the basic design criteria for the mine, it was decided that production would be best achieved by a combination of 40% sublevel long-hole stoping and 60% cut-and-fill mining. Costs of exploration and capital development of per¬manent underground facilities are normally written off over the life of a mine. Production expenditures, on the other hand, are of a temporary nature and are normally charged as and when incurred as an operating expense. Reasonably accurate predictions of mine production costs can be built up from engineering design and estimates of individual mine activities for ultimate inclusion in the comprehen¬sive data required for financial decision making. The simulated operations can be costed on a detailed basis in the form of a monthly operating budget. The budget format can be generalized or detailed, depending upon the scope of the project. However, ex¬perience suggests that a fairly detailed format has the advantage of assuring that all significant cost items are included. For underground costing it is suggested that the budget structure include five major cost centers (i.e. development, diamond drilling, ore extraction, hoisting/ transportation, and general mine expense). These in turn are detailed under numerous subheadings. The mechanism for compiling an operating budget will be illustrated. Because of its relative simplicity, ore extraction under sublevel long-hole stoping has been chosen for illustration. All other activities, simple or complex, can be estimated in similar fashion. BLOCK AND STOPE DEVELOPMENT Long-hole blocks, used where advantageous, will be up to 250 ft in height, depending upon the vertical con¬tinuity of the mineralization, and approximately 300 ft long. Drawpoints will be at 36-ft intervals and serviced by loading crosscuts driven from a footwall drift parallel to and close to the ore zone. Pillars between the stopes will be 50 ft wide. Stopes will be drilled off with vertical rings of blastholes drilled from sublevels approximately 60 ft apart vertically. This drilling will be done by percussion drilling machines (31/2 in.) mounted on a trackless drilling rig. Load¬haul-dump (LHD) equipment will be used to move broken ore from the drawpoints to the orepass connecting to rail haulage systems. On completion, long-hole stopes will be backfilled to prevent caving and to facili¬tate later pillar removal. From a planned stope layout, a forecast of produc¬tion and development is made in Table 1. Table 1. Block Tonnage and Stope Development Quantity Ore Waste Total ore block 375,000 st 2 stopes 310,000 st 1 pillar 65,000 st Access crosscuts, 4 at 100 ft 400 ft Drill sublevel drifts, 6 at 300 ft 1800 ft Stope raises, 3 at 250 ft 750 ft Undercut sublevel drifts, 2 at 300 ft 600 ft Loadout crosscuts at 35-ft intervals 550 ft 100 ft 3300 ft 500 ft Total development footage 3800 ft Tons per ft of development 987 st

Jan 1, 1982

By Mark E. Smith, Gerald J. Gierszewski

Introduction The purpose of this paper is to present a procedure used by the authors for evaluating and designing soil liner systems. This method is particularly valuable in evaluating various treatment schemes for chemically amended soil liners. A tabulation of laboratory test results on various soil types are presented to quantify the effectiveness of certain treatments. A typical liner design program includes developing and proving soil borrow sources, designing the cross-section of the liner system, developing construction specifications, and providing construction services to ensure the intended product is achieved. Material Source Development The first step in designing a soil liner is to identify and evaluate suitable borrow sources within an economical haulage range. This is best done in a two step approach: a reconnaissance level investigation to identify target areas and a detailed evaluation of those targets. Reconnaissance: The goal of the preliminary investigation is to locate potential borrow sources for liner quality soils. This includes all natural materials which can be compacted, chemically treated, or otherwise amended to yield an installed permeability at or below some target value. This requires utilization of all available data sources: Soil Conservation Service, BLM, aerial photos, USGS geologic maps, and project geologist records. The goal at this stage is to locate shallow deposits of favorable soil types. The Unified Soil Classification System provides an excellent first pass grouping. Clays, clayey sands and silts are the most favorable soil types, although silty sands and occasionally clayey gravels can make excellent liners, and are often amenable to chemical modification. The lowest permeabilities are generally achieved with CH, CL and MH soils. Once preliminary targets have been identified using visual examination, laboratory classification tests should be performed to further refine the selection. Testing at this stage should include gradation, plasticity and hydrometer analyses. Additionally, "preg-rob" testing should be done as early as practical. Preg-rob is a phenomenon where gold or silver ions in solution associate with the clay, or other, minerals. When this occurs, a portion of the gold or silver leached from the ore is actually tied-up by the clay and thus a reduces recovery. Testing for this consists of agitating a small sample of the soil in a solution containing dissolved gold or silver, preferably of similar chemical make-up as the solution which will contact the actual liner. The solution and soil are assayed before and after agitation to determine loss to the clay. A reliable estimate of the hydraulic conductivity, commonly referred to as permeability, can be developed from the D10 value by the use of Hezen&apos;s formula: K = 100 (D1012 This relationship is limited to soils where the finer particles do not move due to the force of flowing water (i.e.: "hydrodynamic stabilitym)(1). Additionally, the effect of platty particles on permeability is not as predictable as the effect of equidimensional particles. D10 is the sieve opening size at which 10% of the material is finer. Plasticity is also important from several standpoints. Constructability is directly related to plasticity. Very plastic clays and non-plastic silts both tend to be difficult soils, while medium plastic clays and clayey sands are generally very desirable. Post construction performance is also related to plasticity (e.g. swelling, shrinkage cracking, frost heave, etc.). Additionally, low plasticity silts and silty sands generally do not respond well to chemical amendment. Source Development: The result of the reconnaissance evaluation should be an estimate of the relative probability of developing a suitable borrow source within an economical haul distance. Of course, "economical distance" depends on the degree of handling and treatment the borrow material requires, as well as the cost of synthetic alternatives. The purpose of the detailed investigation is to prove out quantity and quality of material sources, and determine design parameters such as degree of compaction, mixing, treatment and thickness of liner. The emphasis of the testing program should be permeability and strength. Strength becomes increasingly important as the slope of the liner and the height of the heap increase. Permeability testing should evaluate the effects of compaction, water content, mixing and chemical treatment where appropriate. The effects compaction and water content during compaction have on

Jan 1, 1987

By Ian M. Loomis, Keith G. Wallace

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy research and development facility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste. The waste storage horizon is 655 m (2150 ft) below surface in bedded salt. To date the WIPP project has not emplaced any waste. There are three intake shafts used to supply air to the underground. All air is exhausted though a single return shaft. The total design airflow during normal operations is 200 m3/s (424,000 cfm). The ventilation system is designed to provide separate air splits to construction, experimental, and storage activities. Separation is achieved by isolating the storage circuit from the construction or experimental circuits with bulkheads. Any air leakage must be towards the storage area of the facility. Field studies have shown that the pressure differential necessary to maintain the correct leakage direction is susceptible to the effects of natural ventilation; therefore, extensive studies and analyses have been conducted to quantity the natural ventilation effects on the WIPP underground airflow system. A component of this work is a monitoring system designed to measure the air properties necessary for calculation of the natural ventilation pressure (NVP). This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure at strategic locations on surface and underground. The psychrometric parameters of the air are measured every fifteen minutes. From these data, trends can be determined showing the impact of NVP on the ventilation system during diurnal variations in surface climate. Both summer and winter conditions have been studied. To the author&apos;s knowledge this is the first reported instance of automatic and continuous production of time and temperature variant NVPs. This paper describes the results of the initial monitoring study. INTRODUCTION The ventilation system at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, is designed to perform two distinct functions. First, it supports normal mine ventilation requirements complying with all state and federal mine regulations. Second, the system is designed to prevent an uncontrolled release of radioactive contaminants from the storage and transportation areas of the facility. Although a nuclear radiation release in the facility is considered unlikely, many special features are implemented in the ventilation system to prevent the possible spread of contamination. The facility is constructed with the waste transportation and storage areas separated from the mining and non-radioactive experimental areas. The ventilation system is designed such that air leakage is from the mining and experimental areas to the storage areas. Furthermore, radiation detectors are located throughout the storage and waste transportation areas underground and an exhaust filtration building is installed on surface to prevent the possible release of radiation to the environment. For over two years the underground ventilation system has been rigorously tested and balanced. It was during this period that the adverse effects of NVP were noticed and subsequently quantified. From extensive field studies and computer models, several mitigating features were designed and constructed and special operational procedures were implemented to control the impacts of NVP. To quantify more accurately the NVP at the WIPP, a continuous monitoring system was installed. This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure every fifteen minutes at strategic locations on surface and underground. From this psychrometric data, the NVP is calculated. Fan operating pressures and flows and strategic differential pressures are recorded from the site Continuous Monitoring System (CMS). The monitoring system provides a means of evaluating how the ventilation system behaves in regard to climatic conditions and to judge the efficacy of the mitigating features and operational procedures. To the author&apos;s knowledge, continuous calculation of NVP as a function of time and surface temperature has not been previously reported. Overview of the Waste Isolation Pilot Plant The U.S. Department of Energy determined that the plastic nature of bedded salt may provide the best solution to isolate transuranic (TRU) waste from the biosphere. Initial evaluations at the WIPP site began in 1974. In 1979, the United States Congress enacted Public Law 96-164 for the construction and development of the WIPP project. The mission of the WIPP is to demonstrate the safe, long-term disposal of TRU waste generated by the national defense programs of the United States. TRU waste is classified as a low to medium level waste. The waste is stored in drums and does not produce significant heat (not greater than 1 W per drum). The WIPP site is located approximately 47 km (29 miles) east of Carlsbad, New Mexico in the Chihuahuan Desert. The repository is located in the 630 m (2000 ft) thick Salado Formation. This Permian Basin salt deposit is about 225 million years old and appears to have been minimally disturbed by earthquake, faulting, and ground water activity since it was deposited. The underground facility is 660 m

Jan 1, 1993

By David Dvorkin, Thomas C. Anderson

INTRODUCTION A major function of the Mine Safety and Health Administration (MSHA), Denver Safety and Health Technology Center (DSHTC), Ventilation Branch, is to provide engineering analyses of underground mine¬ ventilation systems for coal, metal, and nonmetal in¬spection departments in accordance with field surveys and data analyses. Health and safety problems such as the control of diesel contaminants, dust, methane, radon, and radon daughters all are dependent upon ventilation. It is necessary for the ventilation engineers at DSHTC to have a complete understanding of the various and highly complex ventilation systems used in the nation&apos;s mines. Only through the proper assembly and analysis of data can the engineer determine the causes of prob¬lems and make suitable recommendations. Furthermore, the engineer must have the ability to predict the results of any such recommendations. In the study of the ventilation system at any indi¬vidual mine, it is common practice to collect data on airflow quantities and pressures at key points throughout the mine. However, these data give only a single point¬-in-time view of the system. As the mine develops and progresses, the system undergoes numerous changes; as the mine becomes more extensive, the ventilation re¬quirements increase, and the costs rise. For proper utilization of the available resources, it is necessary for the engineer to have a sound engineering basis for deci¬sions on how best to ventilate the mine. To evaluate the system as a whole, particularly re¬garding possible system changes, it has become necessary to rely on computers to perform the calculations in¬volved in analyzing the network. This chapter sum¬marizes the implementation of such computer capabili¬ties at DSHTC, as well as the services that are available from DSHTC. ANALOG SIMULATIONS AND ANALYSES OF VENTILATION NETWORKS As early as 1954, the US Bureau of Mines (USBM) in Pittsburgh, PA, was using an analog computer as an aid in analyzing ventilation systems. The Mcllroy Fluid Network Analyzer used filament-tube resistance elements and an electrical power supply to simulate mine-ventila¬tion systems electrically. This system is shown in Fig. 1. Analog simulation has proven to be a practical tool, providing fast analyses of complicated problems after the initial setup has been completed. Advancements in electronic technology over the past 24 years have made possible the construction of an analog computer that has streamlined several operating features of the previous machines. The DSHTC Ventilation Branch now has an improved electronic analog computer to assist in the analyses of ventilation systems. General Features As shown in Fig. 2, the analog computer used at the DSHTC Ventilation Branch has three "element" cabi¬ nets, a console, and a printer. The cabinets contain the fan elements and the airway-resistance elements that are used to "program" an analysis problem; each element is independent of the others. The console contains the "patchboard" and the controls necessary to operate the analog computer. The patchboard connects the inde¬pendent elements into the circuit appropriate for simu¬lating the ventilation system. The total system is controlled from a panel on the console, while the value corresponding to each element is set on the individual controls located on the face of each element. The control panel has three visual output displays that give the quantity of flow, the pressure of the output junction with respect to a datum, and the differential pressure across each element. The control panel also allows manual selection of the element to be monitored, or automatic scanning and printing of values for the entire system. Capabilities The analog computer can simulate an existing mine¬-ventilation network. This is accomplished by collecting field data at the mine to give a complete pressure-¬quantity network. Resistance values for each airway branch may be determined from the quantity of flow in the branch and from the pressure differential between the end-point junctions of the branch. The basic rela¬tonship to determine the resistance is expressed as: H=R •Q2 where H is the pressure differential, R is the resistance, and Q is the quantity of air in the flow. After the resistance values are known for all of the airways in the circuit, the elements on the analog com¬puter can be set to the corresponding values. The elements are designed to reflect the basic relationships, with electrical potentials corresponding to pressures and

Jan 1, 1982

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine&apos;s requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By E. F. Klein, R. L. Eacret

Introduction In contrast to the general type of crushing mechanism in which the crushing surfaces alternately approach and withdraw from each other, described earlier in this section, and continuous-pressure break¬ers such as rolls and roller mills that will be described in a later chapter, impact crushers load by striking pieces of rock while in free fall and hurling them at high speed against stationary surfaces. Because the impact crusher depends for its effectiveness upon high velocity, wear is greater than in the slower-moving jaw and cone¬type wear parts, and for this reason its use is strictly limited to rela¬tively soft, friable, and sticky rocks that are characteristic of many nonmetallic mineral deposits. A few of these are phosphates, lime¬stone, barite, clay, asbestos rock, and coal. However, several examples of their use on soft lead-zinc and precious metal ores have been known. Although the use of impact crushers is expanding today into the range of ores containing as much as 15-18% silica, Taggart16 set the practical limit at 5%, and in the 1940s and 1950s several installa¬tions in the US and western Europe exceeded the limits of economical maintenance and were quickly superseded by the slower-moving, con¬ventional crushers. A rock that tends to be plastic or bouncy in a jaw or gyratory crusher when the force is applied slowly to reach ultimate strength, may become brittle with rapid loading and thus increase the effective¬ness of the applied forces. For this reason it is to be expected that as the quality of hammers, grates, plates, and cages improves with advances in steel technology, the use of high-speed crushers of this kind will increase. Terminology Modern usage differentiates between the impactor and the hammer mill, the former relying primarily on the impact of hammers (fixed or free-swinging) and secondarily upon pieces striking one another or steel surfaces; the hammer mill relies on both the centrifugal impact force of free-swinging hammers and the attrition and shear action between these hammers and well-placed grates suspended at the bot¬tom just below the hammer circle. The hammer mill, because of its grate discharge, restricts discharge of oversize rock to the grate open¬ing, while at the same time providing a trap for removal of tramp iron or other uncrushables. The impactor discharges free, so generally works with a screen to control product sizes. The question of terminology, impactor vs, hammer mill, creates difficulties because the similarities appear to outweigh the differences by far; if one were to list the similarities in order of importance and then the differences, he would be forced to conclude that they would best be dealt with as a single kind of crusher. Taggart16 gave it four names and added "as it is variously known," but it must be remembered that in 1945 the machine was nearly exclusively of the flailing-hammer type, while today the fixed-hammer rotor is also com¬mon. In this chapter the terms impactor and hammer mill will be used where they seem to apply. It is perhaps unfortunate that this terminology is being confused with rock breaking at the mine, usually with hand-held tools, e.g., the article "High-Energy Impact Rockbreaking" by Grantmyre and Hawkes, CIM Bulletin, August 1975. General Description Impact breakers, impact crushers, and hammer mills accomplish material breaking and reduction primarily through impact action of the material with fixed or free-swinging hammers revolving about a central rotor. The material to be crushed enters through an opening at the top or top side known as the "feed opening" or "hopper opening" and falls into the path of rotation (hammer circle) of the hammers. Initial breakage is accomplished in midair by collision of the dropping feed material with high-speed hammers. The second stage of breakage occurs when the pieces hit plates or breaker bars which line the crusher boxlike frame. Hammer mills rely further on a shearing and attrition action between free-swinging hammers and grid bars or grates at the crusher bottom which restrict discharge of oversize material until it is broken sufficiently to pass through the grid opening. The term hammer is used in reference to the piece which strikes the material, whether it is fixed on the rotor or free-swinging. It

Jan 1, 1985

By Stephen B. Castor

The rare earth elements (REE) which include the 15 lanthanide elements (Z = 57 through 71) and yttrium (Z = 39) are so called because the elements were originally isolated in the late 18th and early 19th centuries as oxides from rare minerals. Most REE are not as uncommon in nature as the name implies. Cerium, the most abundant REE (Table 1), comprises more of the earth&apos;s crust than copper or lead. Many REE are more common than tin and molyb¬denum, and all but promethium are more common than silver or mercury (Taylor, 1964). Promethium (Z = 61) is best known as an artificial element, but has been reported in very minute quantities in natural materials. Lanthanide elements with low atomic numbers are generally more abundant in the earth&apos;s crust than those with high atomic numbers. In addition, lanthanide elements with even atomic numbers are two to seven times more abundant than adjacent lan¬thanides (Table 1) with odd atomic numbers. The lanthanide elements traditionally have been divided into two groups: the light rare earths (LREE), lanthanum through eu¬ropium (Z = 57 through 63); and the heavy rare earths (HREE), gadolinium through lutetium (Z = 64 through 71). Although yttrium is the lightest REE, it is usually grouped with the HREE to which it is chemically and physically similar. The REE are lithophile elements (elements enriched in the earth&apos;s crust) that invariably occur together naturally because all are trivalent (except for Ce+4 and Eu+2 in some environments) and have similar ionic radii. Increase in atomic number in the lanthanide group is accompanied by addition of electrons to an inner level rather than the outer shell. Consequently, there is no change in valence with change in atomic number, and the lanthanide elements all fall into the same cell of the periodic table. The chemical and physical differences that do exist within the REE group are caused by small differences in ionic radius, and generally result in segre¬gation of REE into deposits enriched in either light lanthanides or heavy lanthanides plus yttrium. The relative abundance of individual lanthanide elements has been found useful in the modelling of rock-forming processes. Comparisons are generally made using a logarithmic plot of lanthanide abundances normalized to abundances in chondritic (stony) meteorites. The use of this method eliminates the abundance vari¬ation between lanthanides of odd and even atomic number, and allows determination of the extent of fractionation between the lanthanides because such fractionation is not considered to have taken place during chondrite formation. The method is also useful because chondrites are thought to be compositionally similar to the original earth&apos;s mantle. Europium anomalies (positive or negative departures of europium from chondrite-normalized plots) have been found to be particularly effective for petrogenetic modelling. REE were originally produced in minor amounts from small deposits in granite pegmatite, the geologic environment in which they were discovered. During the second half of the 19th century and the first half of the 20th century, REE came mainly from placer deposits. With the exception of the most abundant lanthanide el¬ements (cerium, lanthanum, and neodymium), individual REE were not commercially available until the 1940s. Since 1965, most of the world&apos;s REE have come from two hard rock deposits: Mountain Pass, United States, and Bayan Obo, China. GEOGRAPHIC DISTRIBUTION OF REE DEPOSITS More than 70% of the world&apos;s REE raw materials come from three countries: China, the United States, and Australia. China emerged as a major producer of REE raw materials during the 1980s, while Australian and United States market share decreased dramatically (Fig. 1). Table 2 gives recent annual production figures along with estimated reserves by country, and Fig. 2 shows loca¬tions of significant REE mining. MINERALS THAT CONTAIN REE Although REE comprise significant amounts of many minerals, almost all production has come from less than ten minerals. Table 3 lists minerals that have yielded REE commercially or have po¬tential for production in the future. Extraction from a potentially economic REE resource is strongly dependant on its REE miner¬alogy. Minerals that are easily broken down, such as bastnasite, are more desirable than those that are difficult to dissociate, such as allanite. In general, producing deposits contain REE-bearing min¬erals that are relatively easy to concentrate because of coarse grain size or other attributes. For more thorough discussions of REE¬bearing minerals see Mariano (1989a) and Cesbron (1989).

Jan 1, 1994

By Robert H. Merrill

INTRODUCTION In most cases, the design of an underground mine is based upon the premise that the ground either will cave or will be stable. This chapter concerns the design of a mine in ground that will cave readily or with some as¬sistance, such as by long-hole drilling and blasting. Some of the more widely used caving systems of mining are panel caving, block caving, sublevel caving, and large pillar recovery. Some of the less widely used systems are glory-hole, top slicing, and induction caving. Al¬though the common practice of pillar robbing is not usually considered to be a caving system, this subject will be treated as a part of this chapter. BASICS OF CAVING Caving systems are most successful in ground that will cave in sizes that will flow through openings and grizzlies, and will easily load in cars or on belts for haul¬age. The ground most likely to cave well is highly frac¬tured and contains breaks, flaws, or other discontinui¬ties that form planes of weakness. Also, caving action can be greatly enhanced if the host rock itself is low in compressive, shear, and tensile strength. Ideally, a cav¬ing system of mining is best employed when the criteria for caving is a feature of the ore body and the develop¬ment drifts, haulageways, and drawpoints can be mined in a highly competent rock beneath the mineralized zone. However, the development is often in the same, or similar, fractured rock and the openings require sub¬stantial artificial support to assure stability. Several clues can be assembled to identify potential caving ground; however, for borderline cases, no sure method has been devised to date. The diamond-drill cores taken for exploration can provide an excellent clue provided drilling is performed carefully by experienced drillers. For example, if the ground is cored in such a manner that the breaks in the core are caused more by failure of the rock than by whipping core barrels, plugged drill bits, or other drilling causes, and the intact core lengths are consistently long [say, 0.6 to 3 m (2 to 10 ft) of unbroken core], there is little reason to believe the ground will cave without considerable as¬sistance. This is especially true for rocks with compres¬sive strengths above 34.5 MPa (5000 psi) and tensile strengths above 2.1 MPa (300 psi). On the other hand, if core recovery is low (below 80%) and the recovered ore is broken in small pieces and the breaks are along obvious weaknesses in the rock, the chances are excel¬lent that the ground will cave. This is true even when the rock between the defects has high compressive and tensile strength. Another clue has already been mentioned, that is, the measurement of the physical properties of the rock and the natural planes of weakness or defects in the rock. The planes of weakness in the rock can often be detected from outcrops, cores, or other exposures of the rock under consideration. Some rock types are known to be strong and will sustain large, unsupported open¬ings and would be difficult to cave intentionally. Yet the same rock type can also contain unbonded or weak planes of weakness or fractures, and in these locations the rock would undoubtedly cave with little assistance. Therefore, although the inherent strength of the rock is a factor in caving, the natural defects in the rock are more often the deciding factor. DESIGN CONCEPTS For the most part, the design of openings for caving ground is a problem of the interaction of openings over a relatively large area of the mine. To illustrate, Fig. 1 is a simplified section of a series of openings along the grizzly level or draw level of a block caving or panel caving development, and above this opening is a simpli¬fied section of a room-and-pillar arrangement on the undercut level. At this stage of the development, the stresses around the openings on the grizzly level are only moderately influenced by the openings on the undercut level and vice versa. Therefore, the stresses around the openings are approximated by the stresses around single or multiple openings in rock, the values of which are de¬scribed in the literature (Obert, Duvall, and Merrill, 1960; Obert and Duvall, 1967). Once the pillars on the undercut level are blasted (Fig. 2), the situation changes abruptly. The undercut opening (prior to caving) now can be approximated as an ovaloidal opening above the grizzly drifts and this opening tends to shield the vertical stress field. As the caved stage is drawn the stope approximates a much larger rectangular or square opening filled with rock, and if the rock is not sustaining a major portion of the stress field, this opening can be considered (for en¬gineering purposes) to be empty and the stresses that interact between the larger and the smaller openings take on a totally new perspective (see Fig. 3). Next, let the material cave to the surface, and let the caving ma¬terial sustain some stress, but much less than if the ma¬terial were intact. This condition is similar to a soft inclusion in a rigid body and has been treated in the literature (for example, Donnell, 1941). At this point in time, the grizzly drifts are subjected to the stress con-

Jan 1, 1982

By C. J. Lewis

Commercial lime plants in the United States and Canada are depicted in Figure 1. The sources of lime available to Nevada and bordering states are rather few. Chemstar Lime has plants at Apex, Nevada and Nelsen, Arizona. Continental Lime, Inc. has plants at Tacoma, Washington, Townsend, Montana and Delta, Utah. However, Continental Lime has a new rotary kiln installation underway near Wendover, Nevada. This plant is scheduled to come on stream in the fall of 1989.

Jan 1, 1989