Search Documents

By F. Villanueva Araya

Compania Minera Disputada de las Condes (CMD), an Exxon Affiliate stewarded by Exxon Coal and Minerals Company, operates two' copper mines and concentrators in Chile. Pilot plant studies were initiated in 1984 using a 0.46 meter and a 0.91 meter diameter column for the cleaning of copper concentrate. This eventually resulted in the design and operation of a rectangular column with an area of 6.8 m2, increasing the final copper concentrate grade from about 30% to almost 32'1. Cu without any loss in copper recovery. Evaluation studies of a commercial bubble generator as against the previously used filter cloth air sparger are now in progress.

Jan 1, 1990

By Mitchell Gordon

Two mineral processing facilities in North America required near terminal density slurries to perform de-bottle necking in their circuits. The installation at Barrick Goldstrike to ensure efficient oxidation conditions and throughputs in the refractory ore treating autoclaves. The Kidd Metallurgical Division unit to provide a steeper tailings slope to extend the life of the existing tailings dam. To achieve these goals, both operations selected a Supaflo "High Compression" Thickener following on site pilot plant evaluation. Commissioning and the first year of operation is reviewed. Operating data is compared with the pilot plant data. In particular, unusual doughnut formation at Goldstrike and the effect of temperature on the terminal density at Kidd Metallurgical Division are discussed.

Jan 1, 1997

Design models for belt conveyors used in mines predict both the belt power requirements and belt tensions. Conveyors with slightly downhill profiles are more complex to predict due to the way that models such as CEMA interpret friction. Performance of a particular conveyor in relation to other conveyors in the same system requires an analysis of natural stopping times, braked times and take-up location. A review of CEMA-based PC models is presented for design of underground multi-flight belt systems.

Jan 1, 1995

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure, and other types of sensors are increasingly being used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP) while older forms of serial communication are being retired. This paper presents the selection, configuration, and testing methodologies that were employed by researchers from the National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide Internet Protocol data transport. INTRODUCTION To enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry [1]. However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology (IT) infrastructure in place to handle the data transport requirements for the newer IP-based technologies that are part of IIoT. This was the case with a mine in the Western United States; it lacked the infrastructure to perform critical monitoring in remote headings. The mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH’s) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder system to achieve IP data transport using commercially available land mobile data radios. DATA RADIO SELECTION The primary selection criteria for the data radios were network data format, modulation type, and radio channel spacing. The network data format decided upon was Internet Protocol. This format allowed for straightforward integration between the IP-enabled data acquisition system located in a remote heading and the network switch located in the control room. It also eliminated the added complexity of additional network hardware such as Ethernet to Serial converters. IP additionally provided a direct path to integration into higher bandwidth networks, such as fiber optic, should they become available."

Jan 1, 2018

By J. P. P. Silva

Sodium silicate (water glass) is a modifier reagent widely used in flotation with the function of a depressant or dispersant. The interaction between sodium silicate and mineral surfaces is still not well understood. This investigation aimed to illuminate the sodium silicate action mechanism as a depressant in the flotation of the minerals quartz and calcite. The experiments were done with high-purity mineral samples in the particle size range below 147 µm. The microflotation tests in a modified Hallimond tube showed that, in all systems tested, the efficiency of sodium silicate increased with the concentration. At concentrations above 1,500 g/t, almost total depression (96% for calcite and 97% for quartz) was achieved. The variation of sodium silicate modulus did not alter the quartz flotation performance in the presence of amine (150 g/t). The most efficient depression pH range was observed between 5 and 8. Above pH 10, the depressant action of sodium silicate was negligible. The infrared spectra obtained at pH 7 after silicate contact showed the presence of the groups OH and Si-OH, both suggesting that the adsorption of the neutral species Si(OH)4, as well as siloxane groups (Si-O-Si), attributed to adsorption of polymeric species. Sharing electron pairs is the proposed adsorption mechanism between Si(OH)4 and polymeric species and the surface sites (Si-O on quartz and Ca-O on calcite). At pH 11, the electrostatic repulsion prevents the species adsorption, impairing the sodium silicate action.

By V. N. Kolesnikov

The gold-silver deposits of the northern Primorye region are located in the eastern part of the East Sikhote-Alin volcanic belt, where the belt overlaps the Kema island-arc terrain of the Aptian-Albian age. There have been four deposits and numerous mineralization points found in the NE-trending Kema metallogenic belt that is about 1000 km long and 100 km wide. The known mineralization is of epithermal type, controlled by faults, and concentrated in quartz, quartz-fluorite-adularia, and, less commonly, sulfide-quartz vein systems hosted by the Upper Cretaceous-Lower Tertiary volcanic rocks. The vein systems extend for hundreds meters along strike, varying from tens centimeters to 50-60 meters in width. They are surrounded by wide zones of low-temperature hydrothermal alteration containing some gold-silver mineralization for which the commercial value was not studied during the early exploration. The ore bodies contain from 1 to 50-80 ppm of Au and from 1 to 1000 ppm of Ag. Gold is native, associated with quartz, and represented by particles from tens of microns to 1 mm in size. Silver occurs in native form as a constituent of argentite, pyrargyrite, stephanite, and other sulfosalts. The test work carried out for three vein systems 20 years ago showed that gold might be easily and almost completely recovered from the ore by cyanide treatment. The paper describes the geology and mineralogy of the deposits, Salut and Primorskoye, that are the most studied properties of the Kema belt. It also presents the data available on disseminated gold-silver mineralization in stockworks, altered explosive breccias, and wide zones of low-temperature hydrothermal alteration. This mineralization should be explored for possible exploitation as large open-pit, heap-leach deposits.

Jan 1, 1998

By D. A. Knight

The property is located in the Porgera Valley 600 Km North West of Port Moresby. The remote location is 2500 m above sea level. The mine area has 3,600 mm of annual rainfall and a temperate climate with temperatures ranging from 10" C to 22° C throughout the year. Alluvial gold was reported in the Porgera area in 1938 and has been an important source of revenue for the area for many years. Intermittent exploration was carried out until the 1960's when Placer (PNG) Pty. Ltd. with Mt. Isa Mines commenced an extensive exploration program. The property was brought to production in 1990 by the Porgera Joint Venture group consisting of Mount Isa Mines Ltd, Rennison Goldfield Consolidated Ltd. and Placer Dome Inc, each with a 30% ownership and the Government of Papua New Guinea with a 10% share. Placer Dome Inc. is the manager of the property with construction under the direction of the Placer Dome Technical Services group.

Jan 1, 1992

By Richard Giffen, Boris CARO VARGAS, Terrence Carroll

"This paper takes an in-depth look at the $72 million design-build Norris Cut project, which includes the replacement of an existing 54-inch waste water sewer main to Fisher Island under the Norris Cut Channel. Tunneling through one of the country’s most unpredictable geologies created unique challenges in both the design and construction phases of the project. The paper presents the geotechnical and structural design considerations for the 100-foot deep secant piled TBM launch shaft in the highly permeable Fort Thompson formation limestone and sands. The structural design effort also included the design of the tremie slab, thrust wall and design of the largely unreinforced launch shaft to resist asymmetric loading from partial ground freezing. The retrieval shaft was designed as a deep soil mixed shaft and is thought to be the deepest soil-mixed shaft in Miami. From a construction perspective, this paper discusses the unique challenges of building two shafts with two different techniques and will compare some of the constructability aspects, costs and equipment schedule-considerations related to the use of two separate techniques. INTRODUCTION Nicholson Construction Company (NCC) was awarded a $72.1 million Design-Build contract to replace an existing force main from the Virginia Key Central District Wastewater Treatment Plant (CDWWTP) under the Norris Cut Channel to Fisher Island. The location of the project is shown in Figure 1. The project involves replacing an existing 54-inch diameter pre-stressed concrete sewer force main with a 60-inch diameter fiberglass force main. Arup USA, Inc. (Arup) is the lead designer for Nicholson on this design-build project. Arup is providing design services for the TBM launch and retrieval shafts, segmental tunnel lining, the fiberglass pipe, and the horizontal directional drill component. Miami-Dade Water and Sewer Department currently owns and operates the existing 54-inch sanitary force main that transmits sewage collected from Miami Beach and Fisher Island to the CDWWTP for treatment and disposal. The existing force main was subject to a condition assessment in December 2011 which revealed structural deficiencies in the pre-stressed concrete pipeline."

Jan 1, 2016

By J. A. Pontius

The Cresson Deposit is located in central Colorado within the historic Cripple Creek Mining District. The deposit has moved from its initial discovery in 1990 to full production in less than five years (current reserve nearly two million ounces). This accomplishment required a great deal of cooperative teamwork between the exploration, development, permitting and corporate groups. Nowhere was this cooperation more evident than in the construction of the geologic block model. The detailed modeling of gold and its metallurgical characteristics formed the foundation upon which critical financial and design decisions were based.

Jan 1, 1995

By C. Rodriguez, T. BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle. Blasting is the first and lowest cost per ton stage in the comminution value chain. The basic principle that effective blast design can optimize fragmentation from the Run of Mine (ROM) ore muck pile to improve productivity through digging, loading and crushing to grinding and increase mine site profits has been well documented. Benefits of controlling fragmentation in the blast include reduced wear on equipment, faster loading, increased truck loads while detecting oversize rocks at the muck pile can reduce the frequency of a blocked primary crusher. A second basic principle is a measure of particle size distribution (PSD) at each unit operation in the comminution cycle allows engineers to manage blast design to produce fragmentation in the ROM ore most suitable to optimize downstream unit processes to improve mine site productivity and profits. Split-Online® systems have measured PSD of rocks on conveyors from the primary crusher to the SAG mill for over 20 years. Split-Engineering partnered with various mining companies to develop Split-ShovelCam® to automatically measure fragmentation from shovels and excavators working the ROM muck pile. This paper takes the reader “Back to Basics” by discussing the use of real time fragmentation analysis at the muck pile as an important parameter to optimize energy factors required for each blast. Case studies are given. INTRODUCTION The basics of mining are: • Explore for and find economic resources of valuable minerals • Mine rocks containing valuable minerals using blasting • Crush and grind rocks to liberate valuable minerals (comminution) • Recover valuable minerals for sale Comminution is an energy intensive process which accounts for a major proportion of mine site costs. Effective blasting can improve comminution and deliver significant reductions to mine site unit costs, (CEEC, 2016). Engineers, scientists, builders and even philosophers have long promoted the phrase “measure to manage”; the premise being “you can’t improve what you don’t measure”. Blast Engineers measure fragmentation in ROM ore for feedback to manage energy input in the design of blast patterns to optimize the ROM product size for downstream operations, whether they be for ROM Leach or feed into the primary crusher.

Jan 1, 2019

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By J. L. Carr, A. K. Smith, C. C. Jobes, G. T. Homce

"Underground continuous mining machines pose a difficult safety challenge since their operators generally work in close proximity to these machines in very restricted spaces. Intelligent software for use with magnetic proximity detection systems has been shown to accurately locate workers around mining machinery in real time. Calibrating these systems requires the manipulation of a lot of data to determine the calibration constants. Researchers have developed software to analyze, convert, and visualize data acquired during this calibration process to more accurately model magnetic fields and their interaction with the environment. This paper details the background, development, and operation of the resulting application software focusing on the utility of the graphical user interface to visualize the magnetic field calibration data. The refined data developed by this process can then be utilized by the proximity detection system to more accurately identify the location of miners working in an underground mining environment. INTRODUCTION Roughly half of the electricity consumed in the United States is produced with coal, and roughly one-third of all US coal production comes from underground mines [1]. Over the last century underground mining health and safety has seen a continuous and dramatic improvement. However, machine-related injuries and fatalities continue to be a major safety concern [2]. Every year, hundreds of miners are severely injured while operating underground mining equipment, and 39 miners have been killed in striking/pinning accidents involving continuous mining machines (CMMs) since 1984. CMMs, such as the one shown in Figure 1, are large mobile machines that are used to mechanically cut coal in an underground mine. These machines weigh approximately 40 to 50 tons, have hydraulically articulated appendages, and are capable of moving at speeds up to six feet per second [3]. Modern CMMs are remote-controlled, yet the operator and other miners are often in close proximity to the machine. Recent research by the National Institute for Occupational Safety and Health (NIOSH) reveals that the locations workers take relative to the CMM are usually influenced by visibility requirements and safety concerns [4]. The Mine Safety and Health Administration (MSHA) estimates that at least 28 fatalities involving CMMs since October of 1984 may have been prevented with proximity detection technology [5]. MSHA further estimates that proximity detection could prevent 20% of all deaths throughout the industry [6]."

Jan 1, 2016

By K. L. Hanning

Grinding and classification circuits at Climax Molybdenum Co. are described. Since the installation of a direct digital control computer in 1974, a number of control strategies were developed and evaluated. This paper deals in particular with the practical experience and results obtained in direct digital control of a wet grinding circuit consisting of a ball mill, constant speed sump pump, and hydrocyclones. For this circuit throughput is maximized, while maintaining a desired product size. Product size is inferred from measurement of operating variables.

Jan 1, 1977

By L. Berwick, A. Karunanayake, D. Skutt, H. Heath, J. Wang

Thallium (Tl) is a highly toxic heavy metal, soluble over a wide pH range. Tl levels may exceed discharge limits in mining-influenced water associated with processing gold, lead, cadmium, zinc, and copper ores. In this work, the effect of sodium permanganate (CARUSOL® C liquid permanganate) on Tl removal from mining wastewater was studied. Factors influencing Tl removal, namely permanganate dosage/demand, coagulant and flocculant use, order of chemical addition, and co-existing metal ions were examined. The results show that permanganate addition is very effective at removing Tl to below target limits and can provide a unique solution for improving wastewater quality and optimizing overall treatment costs. In addition, several on-line monitoring techniques were evaluated for process optimization. The Hach DPD Free Chlorine method was optimal, allowing plant operators to rapidly and easily spot check effluent samples for excess permanganate dose.

Mar 2, 2022

By William Gleason

The mining industry is at a crossroads. Currently, there is an estimated $25 billion worth of projects around the world that have been stopped as the consequence of a dispute or disagreement with their communities, the government or some other stakeholder. Anglo American chief executive officer Mark Cutifani is one who sees the mining industry in need of change and on Dec. 12, he gave the keynote address for the launch the Kellogg Innovation Network?s Mining Company of the Future Initiative?s Development Partner Framework (DPF). The launch was held at the Ford Foundation building in New York City. The DPF seeks to inspire and support the mining industry to adopt a new way of thinking and a new approach to how it secures, nurtures and revitalizes its social license to operate. Working with a diverse group of people from faith-based organizations, nongovernmental organizations (NGO) and other stakeholders, Cutifani often had the rather uncomfortable position of representing the mining industry in a room full of people who are far from the industry?s biggest fans.

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By Paul Soros

There has been a steady increase in shiploading capacities in the last 20 years. One of the reasons has been the general increase in ship sizes, with the largest vessels currently around 280,000 DWT in the bulk trades. Obviously, the large vessels can accept loads faster and their economic utilization justifies higher loading rates, up to a point. The high capacity facilities have loading rates far beyond this point. The economic logic of these facilities is based on the fact that for a given annual throughput the capital and operating cost of a single high capacity system is less than that of two smaller systems. Thus, where the projected throughputs are large, there is a great incentive to reduce capital costs by maximizing capacity. Tubarao, in Brazil, designed for a 100 million ton per year throughput with one finger pier and one high capacity berth is a successful demonstration of this approach. In the current state of the art, the high capacity systems have shiploading capacities in the range of 10,000 - 16,000 TPH, for annual throughputs of 20 million tons and larger per loading berth.

Jan 1, 1982