Search Documents

By Robert W. Row

Advanced physical coal cleaning processes that are now under development may remove significantly greater fractions of pyritic sulfur and ash than do commercial coal cleaning processes at comparable heating value recoveries. These processes may be useful for reducing sulfur dioxide emissions from electric utilities and other emission sources. However, little work has been done to determine their applicability to any major coal market. The northeastern states of the United States are interested in burning more coal, but with further sulfur dioxide emission restrictions. Their nearest coal sources are relatively high sulfur Northern Appalachian coals. The project discussed in this paper, which is scheduled to be completed in June 1985, has the objective of technically and economically evaluating various coal supply scenarios involving five selected advanced physical coal cleaning processes; and comparing the economics of them with alternative fuel supply options open to the northeastern users.

Jan 1, 1985

By Shiro Ishii

When construction sites are in a densely- populated area or near roads, railroad or river, restrictions upon the ways of handling and using explosives such as dynamite and large demolition equipment are being increasingly stringent, in consideration of environmental pollution such as noise, vibration, dust, flyrocks etc., and safety precaution. In view of this, the development of safe and pollution-free technology for demolishing rocks at mines and reinforced concrete structure at building sites is strongly required. To meet such requirements, the demolition by means of expantion of mineral substances has been considered long before. Recently with the demolition technique using non-explosive demolition agent developed by ONODA CEMENT CO., LTD., holes are drilled into substances to be demolished, such as rocks and concrete before-hand. Then, slurry of such agent mixed with an appropriate quantity of water is poured into the holes. It hardens and expands with the passage of time, and the expansive stress reaches more than 3m/m2 in 10 to 24 hours. This expansive stress causes the material to crack. In this article, descriptions of the non- explosive demolition agent, BRISTAR manufactured by ONODA CEMENT CO., LTD., TOKYO, JAPAN, are given briefly with regard to its physical and chemical properties and its method of use; and the way it is used at an actual construction site is reported.

Jan 1, 1982

By Edward C. Mabbs

U.S. industry must increase its productivity or lose its competitive position in the rapidly expanding and inter-dependent world markets. Recent improvements in material handling techniques and equipment, coordinated with production processes, provide one of the greatest opportunities to increase productivity. Successful managers must learn how to take advantage of these material handling opportunities to gain competitive position.

Jan 1, 1973

By J. L. Parks

Designs, installation procedures, and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install, and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic 12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.

Jan 1, 1992

By P. C. Thakur

Methane has been a hazard since the beginning of coal mining and has influenced, more or less, every aspect of coal mine design. It is receiving increased attention lately because the rate of methane emission in coal mines is increasing as increasing demand for coal leads to exploitation of deeper seams and the use of higher productivity equipment. Consequently, the government and private industries have directed a great deal of effort towards understanding and solving the problem of methane emission in coal mines. In the United States, Consolidation Coal Company has pioneered research in this area since the early 1950's.1 Currently this work is being expanded by Consol through the Mining Research Division of the parent company, Continental Oil (Conoca), to find new techniques for degasification of virgin areas as well as control of methane in gob areas. Basic reservoir properties of coal seams, such as gas content, reservoir pres-sure, diffusivity, porosity and permeability are better understood today largely through the efforts of the U. S. Bureau of Minese2,3,4 It is possible now to identify and model the basic mechanism of gas emission from coal and to forecast steady as well as unsteady state emission of methane in coal mines with some degree of reliability. Combining this knowledge with any ventilation simulator should often identify problem areas in advance and permit adequate methane control measures to be planned.5 Another recent innovation in methane control is the horizontal hole drilling technology. The U. S. Bureau of 1-1ines and the Mining Research Division of Conoco have independently developed techniques for drilling horizontal holes 300 to 600 m deep6 The Bureau's method employs a rotary drill string while Conoco uses a non-rotating string with a down hole drill motor. It is the authors' view that the latter provides more positive control on bore hole deviation both vertically and laterally and appears to be faster, though somewhat more difficult to operate. The rate of methane emission depends on a number of factors which can be broadly classified in two groups. These are (1) the basic reservoir properties of

Jan 1, 1977

By Xie Junjie, Li Shina, Ma Ruixin, Min Changli, Yin Zichen, Li Kang, Shi Zhuonan

Cesium and rubidium were effectively separated by zinc ferrocyanide coprecipitation method, and the effect of precipitant addition amount on the separation of cesium and rubidium was studied. Under the conditions of Zn/Cs molar ratio of 0.45 and Zn/Fe molar ratio of 1, the precipitation rate of cesium is 84.01% and the separation factor of Cs/Rb is 164.65. The thermogravimetric curves of the sediment were measured, and the effects of roasting temperature, roasting time, and leaching liquid/ solid ratio on the extraction of cesium were studied. Almost all of the cesium was extracted under optimal conditions: roasting temperature of 600 °C, roasting time of 3 h, leaching temperature of 25 °C, leaching time of 0.5 h, and liquid/solid ratio of 5:1 mL/g. After the leaching process, the leach liquor with high concentration of cesium of 80.17 g/L was obtained. Finally, the leach liquor was further purified by solvent extraction, and the purity of the cesium chloride product reached 99.66%.

Mar 17, 2024

By J. R. Tonry

In the grinding of dry non-metallic materials such as rocks, ores, gypsum, lime, and cement clinker, it is recognized that only a relatively small portion of the energy is utilized for actual size reduction, and the major portion of the energy used is converted into heat. As a result, heat is generated inside grinding mills imparting to the ground product a higher temperature than that of the mill feed. In some cases, as for instance in grinding cement clinker and gypsum into finished cement, it may be desirable to keep this temperature increase within certain limits, to avoid any change in the properties of the product and, because consumers may specify a maximum temperature of the finished product for reasons associated, with the tulimate use of the cement. The actual proportions of heat and useful work are somewhat indefinite. Some tests have indicated that nearly all the energy is converted into heat, and. other investigators have found that they could account for "everything except the noise." Investigations sponsored by the American Institute of Mining and Metallurgical Engineers, and carried out with an adiabatic calorimeter, indicated that a surprisingly high 19 percent of the energy might actually be used for size reduc¬tion. However, for the purpose of the following discussion it will be assumed that: (Fig. 1) 10% is lost in motor and gears 10% is lost by radiation and convection from the mill body 10% is used for size reduction, and. that 70% of the energy input leaves the mill as heat in the ground. product. A typical example (Fig. 2) would be a 7x22-ft tube mill operating in open circuit, driven by a 400 hp motor, charged with 77,000 lb of grinding media and producing 70 bbl or 26,300 lb of cement per hour. Reducing this cement from a clinker size of 96 percent passing a No. 16 mesh sieve to a specific surface of 3,230 sq cm per gm (Blaine) will increase the temperature of the cement approximately 143F above the temperature of the feed, as explained later. If the tempera¬ture of the clinker therefore is 125F, the finished cement will be 268F, which in some cases may be too hot. : When cement temperatures approach a range during grinding where dehydration of the gypsum becomes a problem, a logical consideration would be some means of reducing the temperature before it attains the range conducive to gypsum dehydration. Regardless of the varying degrees of heat generated within the mill or mills during grindingto various finenesses, consideration of the maximum safe limit for any type of cement being ground, which may vary fromplant to plant, govern in refining the mill circuit to obtain a safe temperature range. All plants are not necessarily required to do the same cooling job, and may or may not use cement coolers following the grinding circuit. (Not discussed in this paper). In the past, various means have been employed for controlling this temperature increase, Such means have included water cooling of the outside of the mill shell; equipping the shell with cooling fins; injection of moisture inside the mill; ventilation through the mill; and., in cases of closed-circuit grinding, drawing cooling air through the classifier; the purpose in all such cases being to remove heat from the grinding system.

Jan 1, 1958

By L. Adler

A systematic, balanced and inclusive formulation of the vast input data for mine design is presented. Since the quality of this statement severely influences subsquent design it is extremely important to senior mining engineers and the profession-at-large. If unfocussed, chaos can result along with serious ommisions. The basic categories, each a traditional one are: 1) Natural Conditions (geology and geography), 2) Company Capabilities (monetary and managerial), 3) Public Domain (regulations, contracts, good will, etc.) and 4) State of Art (mining engineering professionalism). To further reduce the data additional organizing principles were used: the distinctions of mining (vs. civil) engineering, proceeding from the general to particular, the basic engineering dimensions, and separating dependent from independent variables. The results are a unique and unified corpus, which anticipates the mine design procedure.

Jan 1, 1987

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By E. A. Noble

In the Western Coal Region, successful reclamation of surface-mined areas includes the protection of groundwater sources. To accomplish this, a complete understanding of the geohydrology of the affected area is imperative. Successful mine design also calls for careful attention to geohydrology. Because the Western Coal Region is semi-arid land used mainly for farming and grazing, groundwater is a particularly sensitive topic. It is especially sensitive where the lignite scheduled for mining is itself the aquifer supplying the farms and ranches. Such is the case throughout much of the Western Coal Region, particularly where there are no near-surface sand and gravel aquifers that are commonly found in the glaciated portions of the Region. Just as mining can adversely affect groundwater supply, so can groundwater adversely affect mining. Mine flooding and highwall instability are examples of this. But, mine operators must realize that procedures they use to remedy geohydrologically-related mining problems can have a dramatic effect upon ground- water conditions in areas adjacent to the mine. A logical precaution is to require the acquisition of complete baseline data prior to making the first cut. We recommend that the mining plan not only incorporate the reclamation plan, but that they be developed as one plan.

Jan 1, 1976

By M. A. Reyes, J. Bickson, J. R. Srednicki

Federal laws mandate the presence of refuge alternatives (RAs) in underground coal mines and provide guidelines for harmful gas removal. After an explosion, harmful gases can follow survivors into an RA and can reach a deadly concentration. Investigators from the National Institute for Occupational Safety and Health (NIOSH) tested 12 ventilation system configurations (VSCs) to purge sulfur hexafluoride (SF6) tracer gas from a built-in-place (BIP) RA in the Experimental Mine in Bruceton, PA. Using a borehole air supply, tests were conducted with airflows of 750 and 1,000 standard cubic feet per minute (SCFM). Excluding a VSC where the air inlet was 1.98 m (78 in) from the air outlet, the results show that the time to purge the SF6 concentration from 1,000 parts per million (ppm) to 25 ppm ranged from 26 to 29 minutes for an airflow of 750 SCFM and ranged from 18 to 23 minutes for an airflow 1,000 SCFM. Mines can use this information to reduce purge time in case of a mine disaster and determine which VSC to avoid. INTRODUCTION After a fire or an explosion in an underground mine, the concentration of carbon monoxide can reach a fatal level. In a mine disaster, the main goal is to escape. However, if miners cannot escape, they have to migrate to a location to find refuge and, if possible, communication, and a borehole source for a fresh air supply. To ensure survival of the miners, Federal laws mandate the presence of a refuge alternative (RA) within 304.5 m (1,000 ft) of the nearest mining face. In addition, Code of Federal Regulations Title 30 CFR Section 7 sets the guidelines for personnel tracking, RAs, and the removal of noxious gases in underground coal mines (Mineral Resources, 30 CFR, 2014). Federal regulations define an RA as a protected, secure space with an isolated atmosphere and integrated components (Mineral Resources, 30 CFR, 2014). There are three types of RAs: portable metal RAs, portable tent-type RAs, and built-in-place (BIP) RAs. A BIP RA is constructed using masonry or other stoppings to create an isolated space in a mined-out area. Blast doors are installed in one or both of the stoppings for the miners to enter the RA. Furthermore, RAs must provide the following components: breathable air, food, water, air monitoring, and harmful gas removal. Federal regulations have emphasized the mandate for breathable air and harmful gas removal in the following words: “Purging or other effective procedures shall be provided for the airlock to dilute the carbon monoxide concentration to 25 ppm” (Mineral Resources, 30 CFR, 2014). The purpose of the mine ventilation system is to provide a sufficient quantity of air to the underground mine workings, to dilute methane and other contaminants, to maintain a suitable working environment, and to prevent accidents from happening (Cheng and Wei, 2014). In addition, the organic nature of coal amplifies risks from poisonous gases, explosions, and fires (Engström et al., 2018). If an underground coal mine ventilation system fails after an explosion, the concentration of toxic gases, most notably carbon monoxide, will increase. Carbon monoxide is dangerous because it creates tissue hypoxia by binding to hemoglobin (Özmen and Aksoy, 2015).

Jan 1, 2019

By C. K. C. K. Gupta

The rare earths in elemental form are required for a variety of scientific and technological purposes. They are not easily obtained in this form, due to the great chemical stability of the rare-earth compounds and the strong tendency of elemental metals to react with everything they come in to contact with, especially at high temperatures. Beginning in the 1950s, when sufficient quantities of separated rare earths became available, as the result of intense research and development, three processing routes were developed to accomplish the preparation of all 16 naturally occurring rare-earth elements. They are chemical reduction of the halide intermediates, the oxides and electrochemical reduction of chlorides and oxide-fluoride mixtures. Not all the processes are effective with all the rare earths. In spite of the celebrated similarity of trivalent rare earths, the physical properties of individual rare-earth elements are sufficiently different that a variety of techniques are required for their preparation. The development of reduction processes for the rare-earth metals are covered in this paper, with focus on the oxide reduction routes. The strong reliance of effective reduction processes on the fundamental science of reduction reactions is highlighted.

By A. R. Negele

Kaolin-based pigments are the most widely used pigments in the paper industry. Several types are available and include standard hydrous, delaminated, calcined, chemically-structured, and most recently, composite pigments. Within each category, a spectrum of products is available to satisfy the application requirements of paper producers. The paper industry has a broad range of applications including fillers in woodfree and groundwood-containing papers, pigmented size press applications, ultra-lightweight and lightweight coated papers, coated merchant papers, cast coated papers and coated paperboard. Each application has its own set of performance criteria and suppliers must work with mills to identify appropriate product(s) to fulfill these requirements.

Jan 1, 1993

By F. A. Molloy

As a result of feasibility studies made in 1975 a 3-0 seismic reflection survey was shot over part of the Veendam salt pillow during 1978-1979. The Zechstein salt pillow, located in the northeast of the Netherlands near the town of veendam, occurs at a depth of 1400 m and contains three carnallite rich horizons over an interval of 300 m below top salt. MgCl2 brines are produced from these layers as feedstock for a magnesia plant, which starts up in 1981. Prior to the acquisition of the seismic data four wells had been drilled. The thickness of the carnallitite layers encountered in these wells varied between 50 and 125 meters. In view of these variations it was necessary to obtain a reliable isopach of the different layers. The 3-0 seismic survey covered an area of ± 4x4 km with a sampling interval of 20 m in all directions. The data was recorded it an area array using a 120 channel instrument. Final presentation of the data was in the form of 3-0 migrated acoustic impedance cross sections. The quality and resolution of the seismic data allowed reliable structural and isopach mans to be made. It was shown that the carnallitite layers are continuous over the area surveyed, whilst local thickening is "fault" related. Having this information brine production locations could be choosen in the thicker parts, allowing maximisation of production potential whilst avoiding faults and fulfilling mining regulations. A subsequent benefit of this approach is the possibility of using the seismic data to predict ore grade. Using the available wells as calibration points the acoustic impedance response of the seismic at the well was matched to the ore grade found. From these points a synthetic section was made with varying ore grades. Pre¬liminary results are encouraging and the liability of this predictive tool will be evaluated in the light of future drilling.

Jan 1, 1981

By C. Tom Blevins

LADIES AND GENTLEMEN : This presentation is to discuss production and roof control problems associated with directional lateral stresses in an in situ stress field and the approach that Inland Steel Coal Company made in trying to cope with them. Before proceeding, a brief description of the mine location, product, geology, restraints, and mine history is in order.

Jan 1, 1982

By W. P. Blacutt

A financial-economic model incorporating physical, market, and policy variables is developed for mining investment in Bolivia. Additional risk criteria emanating from political instability. new mining legislation, recent environmental regulations, and a new minerals taxation system are accounted for and are integrated into the investment decision model. Results of the model indicate that geologic and market variables have the dominant effect on the investment-worth function. Among policy variables, exchange rate and taxation policies have the most significant influence. Depreciation allowance for infrastructure development has negligible weight in the investment-worth function. The business structure of the firm considering investing in the Bolivian Polymetallic Project is found to be an instrumental factor in the investment-worth outcome. Specifically, undiversified mining companies whose operations exclude zinc production as the primary source of revenue would benefit most from adoption of this project.

Jan 1, 1993

By Michael J. Friedel

The permeability and flow capacity in unsaturated media is investigated by the Bureau of Mines for application to in situ copper leach mining at the Cyprus Casa Grande mine site. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through rubblization. By producing a maximum block diameter of 4 m, injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 1991

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By Mehmet Guney

[The Atlantis-II-Deep is a hydrothermal mineralization located along the median valley of the Red Sea at a water depth of about 2200 m. Extensive exploration of the metal-rich brine deep revealed a potentially mineable deposit on economic interest consisting of oxides, silicates and sulphides with considerable concentrations of zinc, copper, cadmium and silver. Geostatistics was applied to assess the most likely in-situ vague of the metal potential for economical exploitation. Semi-variograms were constructed to characterize the structure of the regionalized distribution of the geological parameters. Volume grades and thicknesses were determined by the kriging technique, avoiding systematically biased high or low grades, and then block .tonnages were computed. The estimation variances, distribution of errors and histograms of observed and kriged values in each grid Mock were also produced.]

Jan 1, 1983