Search Documents

By Sigmund J. Sulinski

All Sanitary District contract documents for new tunnel construction permit the Contractor a choice of four (4) separate alternate tunnel sections. This is the result of a continuing District policy to encourage at all times the use of the most suitable construction techniques and to attract to District construction the broadest spectrum of proven capabilities. Figure 1 indicates the alternate tunnel sections allowed on District contracts as follows: 1. A horse shoe section, ribbed and lagged, and a poured reinforced concrete tunnel liner; 2. Circular section, ribbed and lagged, and a poured in place reinforced concrete tunnel liner; 3. Circular section, ribbed and lagged, and a precast reinforced concrete pipe liner grouted in place; and 4. Circular section, no temporary lining, and a precast reinforced concrete pipe liner to be jacked in place. The Sanitary District now has in operation 10,500' of 5'6" I.D. and 6,500' of 5'0" I.D. jacked tunnel. An additional 5,600' of 7'6" I.D. jacked tunnel is currently under construction.

Jan 1, 1997

By W. S. Weldon

The use of spiral separators for the beneficiation of fine coal typically in the size range -2+0.1mm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimize metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Jan 1, 1997

By J. D. Lowell

The gold content of prophyry copper deposits ranges from less than .05 gmt (ppm) to more than 1.0 got, and most deposits contain on the order of 0.05 gmt Au. Perhaps the highest grade mineralization which has been found in close proximity to a porphyry copper is the Ok Tedi Gold Cap orebody whose grade falls in the 2-3 gmt Au range.

Jan 1, 1988

By Yoshihiro Kawarabata

INTRODUCTION With only about 30% of Japan's entire population served by sewer systems at the end of 1980, extensive sewerage construction programs have been implemented. As major sewer networks in large cities are near completion, construction of smaller sewer networks in less populated areas and branch sewers in urban areas is on the rise, where a demand for sewer tunnels of 600mm to 1500mm diameter is very heavy. The pipe jacking technique, usually employed to excavate such small diameter tunnels, therefore has become the subject of further technological development and sophistication to cope with the increasing volume of construction. At the 1979 RETC, the state of the art on the slurry shield tunneling method at that time was reported. This paper is a follow up to the last paper and discusses a newly developed boulder crushing equipment and automatic pipe jacking system for the slurry shield method and their application. Such technological advancement as high-degree mechanization and automation will significantly improve tunneling operations in response to the aging society to come. Through application of the technique on so called factory automation, this is a step towards field automation for the construction industry.

Jan 1, 1983

By T. Malterer, R. Adams

Peat has unique physical, chemical and biological properties. These include high porosity and water retention, high absorption and adsorption properties, and high buffering capacity. In addition, peat is a rich medium for microorganism activity. Peat has traditionally been used for horticultural purposes. However, in recent years, peat is increasingly being used for waste- treatment purposes. This paper reviews North American literature on the use of peat for waste-treatment applications. The literature indicated that peat has potential for use in the treatment of municipal and on-site effluents, for the removal of low concentrations of heavy metals and for the adsorption of liquid and gaseous hydrocarbon pollutants.

Jan 1, 1997

By Martin Valeri

The operation described in-this paper will be confined to the Nemacolin Mine of The Buckeye Coal company, Nemacolin, Pennsylvania.' This mine is-located on the Monongahela River approximately sixty miles south of Pittsburgh. The mining is in the Pittsburgh seam that has an average thickness of 88 to 90 inches. The current practice is to mine approximately 80 inches, leaving 8 to 10 inches of roof coal. All of the coal produced is used solely for by-product coking by the parent Youngstown Sheet & Tube Company, Youngstown, Ohio. Eight to ten inches of top coal are left by the miners to prevent air slacking of the draw slate. In addition, this top coal which will float at the washing gravity has a very high ash and sulphur content, and when mined, seriously affects the quality of the clean coal product.

Jan 1, 1961

By L. M. Litz

In reply to Mr. DeVries comments on my paper, I would like to say that it is true, as pointed out by Mr. DeVries, that under some special conditions, the use of high concentrations of hydrogen peroxide might provide higher short term in-situ …

Jan 1, 1982

By G. T. Swanby

Members of AIME, I read to you now a portion of a very fine business letter which we received several years ago. This letter originated in Rangoon, Burma, and reads in part: "Rest assured, if your goodselves see with us eye to eye, sure as certain we should get the business". I don't plan to give anybody "the business" today, but you can rest assured that if some of "you goodselves see with me eye to eye" on what I am about to discuss, I would be most pleased. My talk with you today will discuss the Federal Corporate income tax and its effect on our lives as engineers. In the-engineering-construction business we are faced with all the usual form of taxation which includes such items as sales tax, use tax, school tax, contractor; gross receipt tax, import duties and excise taxes, severance taxes, etc, adinfinutum.

Jan 1, 1965

By J. Koinig, K. Mussger, St. Reischl

Jet grouting is a viable supplementary measure for NATM tunneling in special softground conditions. In particular it is used as a type of forepoling to maintain face stability and to provide initial support for large openings until the shotcrete lining reaches sufficient strength. For this purpose cement grout is injected under high pressure through horizontal pipes outside of the tunnel perimeter and thoroughly mixed with the soil producing 1 to 3-foot diameter cylindrical beams. Excavation of the tunnel then proceeds beneath this umbrella of 40 to 50 foot long beams. Design and construction experiences from recent projects are presented for tunnels diameters between 30 and 50 feet in fill and alluvial and colluvial deposits.

Jan 1, 1987

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

The generation of microscopic bubbles by cavitation may enhance particle-bubble attachment and improve flotation performance. It is shown in this paper that tiny bubbles or cavities can be generated by strong shear and turbulence in high speed liquid flows. These conditions create the necessary pressure fluctuations in the bulk water to cause the local pressure to drop below a critical value. The formation of bubbles is favored by high dissolved gas contents to promote gas diffusion into the cavities, and by the presence of surfactants to provide some mechanical strength due to the adsorbed film. Experimental results on bubble formation by cavitation and consequent flotation of fine silica (d50 = 1.6 µm) are presented.

Jan 1, 1995

By J. E. Garlanger, R. K. Shrestha

During mining, the surficial aquifer and, in some cases, the top of the uppermost confining unit within the mined areas are excavated. Portions are removed from the area for resource recovery. Until the mined areas are reclaimed, the surrounding unmined area continues to dewater. The impact of mining and subsequent restoration of the surficial aquifer on the ground and surface water resources of the watershed affected by the mining will be described. This will be done in terms of ground water recharge, ground water levels, and base flow and runoff to surface streams. Data from actual mining situations will be used in analyses and discussion. Recommendations will be made for further research.

Jan 1, 1992

By M. A. Sochocky

Rod mills were developed, as a logical substitute for the rolls crusher when larger tonnages had to be handled, on a continuous basis. Today, with even larger tonnages to process, the trend is to install larger equipment, automate the plant and develop the highest availability possible, in order to cut costs. The rod mills, because of design limitations in size and speed 1'2, are not able to meet these new requirements. The autogenous mill was a timely development and serves as an excellent alternative for ores that are suitable to this type of grinding. When ores are not amenable to autogenous grinding, selection of a flowsheet is dictated by liberation characteristics and unit operations to be used for mineral recovery.. The following alternatives are available: (a) Multiple rod mills, capable of drawing no more than 2000 HP each, followed by ball mills. (b) Gyradisc crusher followed by two stages of ball mill grinding.3 (c) Tertiary crushing followed by closed circuit single stage ball mills grinding to approximately -100 mesh, as in the copper industry. (d) Tertiary' crushing followed by two-stage, ball milling. Each stage will operate in closed circuit with either screens or cyclones. It is this last alternative, particularly as it

Jan 1, 1972

By Bryce T. Tripp

Utah's abundant industrial rock-and-mineral resources support a relatively small but important sector of the State's economy. In 1983, six of the top 10 nonfuel mineral commodities (by value) were industrial commodities. Portland cement was ranked fourth, potash fifth, halite sixth, phosphate seventh, construction sand and gravel eighth, and lime tenth. Portland cement was produced by three operators, principally from the Jurassic Twin Creek Limestone. Potash was produced by three companies from Pennsylvanian beds in the Paradox Basin, surface brine of the Great Salt Lake, and subsurface brines of the Great Salt Lake Desert. Halite was produced by eight operators, primarily from surface brine of the Great Salt Lake. Additional production came from salt beds in the Jurassic Arapien Shale, solution mining of the Pennsylvanian Paradox Formation of the Hermosa Group, and subsurface brines of the Paradox Basin. Phosphate was mined by one company from the Permian Meade Peak Phosphatic Shale Member of the Park City Formation. Construction sand and gravel were produced by dozens of operators, primarily from Quaternary Lake Bonneville beach and nearshore deposits. Lime was produced by four operators from Paleozoic formations in the Basin and Range physiographic province of Utah. The future production of these and other industrial commodities, though individually uncertain, is expected to increase gradually as a group. Factors favorable for the future of the industrial commodities industry in Utah include large to almost unlimited resources for the major commodities, a healthy projected population growth, an abundant local supply of relatively inexpensive energy from coal and natural gas, and a favorable corporate tax structure and business climate.

Jan 1, 1987

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By D. S. Choi

This paper presents the results of geomechanics work applied to the longwall operation. The mining method was successfully adapted to US mining conditions resulting in an improvement in safety and productivity. The paper deals with various geomechanics problems associated with geologic and mining conditions.

Jan 1, 1987

By Robert T. Beckman

Education of inspection and operating personnel is essential to protection from radiation hazards in the mining industry. For over 10 years, MSHA has presented the only formal course on radiation measurements and control available to the mining community. Course objectives and content are described in this paper.

Jan 1, 1981

Draglines are one of the largest land-based equipment moving across the earth. They typically ranging in size from2.5 to 6.5 kt (2,750 to 7,100 st). Their size, though, makes them difficult to maintain. Recently, G&S Engineering Services used an Enerpac synchronous hydraulic lifting system to lift a 3.2-t(3,500-st) dragline at the Curragh Mine in Queensland, Australia’s Bowen Basin.

Jan 1, 2004

By Bela Koman

Abstract - A shiploading terminal near Punta Arenas, the southernmost city of the world (lat. 53°-10'S, long. 70°-54' W) is described. Strong winds, choppy seas, frequent gales, rain, and snow make it difficult to load ships at an offshore berth in this area. Detailed site investigations, including a wind-recording program, supplied sufficient information for the analysis of operating conditions. The weather pattern of the entire region, including the predictability of gales, was utilized in the analysis. The results showed that a bulk loading terminal at this location is feasible, provided that the design takes into consideration the specific problems of the site. The final layout shows a terminal that can be approached from several different directions, depending on the direction of the wind. The mooring system is arranged to allow alter- native ways of attaching and casting off mooring lines and executing docking and departing maneuvers. The berth is supported on piles and contains the minimum of structures, relying on a slewing shiploader to reach the ship in any position, with only limited fore and aft shifting of the vessel for loading the extreme hatches. Results of wind recording, statistical analysis of wind and wave data, operating criteria, and the results of berth availability analysis are included in the paper.

Jan 1, 1987

By Andrew L. Mular, Richard R. Klimpel

Optimization strategies of possible interest to mineral processing are reviewed and typical strategies initiated in processing plants to date are discussed. Both On-Line and Off-Line optimization procedures have been employed by industry, assisted either by operators or by digital computers. In every case, dollar benefits have accrued.

Jan 1, 1991

By Didem Maral

Olivine is a name of a mineral group that has a chemical formula of: (Mg, Fe), SiO4. The most important rock for the olivine group minerals is dunite, which can contain olivine up to 95-99%. Dunite can be obtained from chrome enrichment as a by-product. As a result of alteration of the olivine group minerals, several kinds of different minerals can occur. Main consumption areas of olivine are steel and iron industry. Also olivine is used in not only casting and refractory industries but also production of radiator, ballast material and abrasive. North of Bursa-Orhaneli has got more than 5 billion tons reserves in ultrabasic massifs. M.T.A found that olivine has got high quality of using in refractory and casting industry.

Jan 1, 2005