Search Documents

By John R. Duble

Through 1980, demand for cement in the Pacific Basin countries still seemed to exceed output. Availability of cement in the industrialized and developing countries of East Asia, Southeast Asia, and Australasia for the 1975 - 1980 period are discussed in this report. Quantitative data includes production, imports, exports, and apparent consumption. An account of new cement plants and plant extensions is provided. Countries and areas covered include: East Asia---Japan, South Korea, North Korea, Taiwan, China, Hong Kong, Philippines; South east Asia---Thailand, Vietnam, Singapore, Malaysia, Indonesia; Oceania (Australasia)---Australia, New Zealand, New Caledonia, Fiji.

Jan 1, 1982

By L. H. Munson, D. E. Hadlock, L. F. Munson, R. L. Gilchrist, P. D. Robinson

All uranium mills are required to perform sampling and analysis for radioactive particulates in their gaseous effluent streams and in the environment. Pacific Northwest Laboratory was requested by the U.S. Nuclear Regulatory Commission (NRC) to provide technical assistance to them for their Uranium Mill Health Physics Appraisal Program. In conducting appraisals, air sampling methods used at NRC-licensed mills were reviewed and several deficiencies noted. This paper includes only environmental and effluent particulate sampling although much of the information is applicable to both in-plant and environmental samples. First, the components of a proper sampling program are discussed: program objectives, program design, sampler design, analyses, quality assurance, and data handling. Then the specific deficiencies, or the "pitfalls" from the first 8 mill appraisals are discussed. The first consideration in establishing an air sampling program is defining the objectives of the program. What is air sampling suppose to accomplish? Many of the deficiencies we have observed have resulted because the desired objectives were not clearly established in the minds of the radiation safety staff. PROGRAM OBJECTIVES An environmental air sampling program ought to fulfill the following seven objectives. The first is to: 1) [demonstrate regulatory compliance]. Although a goal of most programs, regulatory compliance, is not well understood. One has not only to comply with the conditions of the source materials licensee, but one must also demonstrate compliance with 10CFR20 and 40CFR190. For example, 10CFR20.106 states: "A licensee shall not possess, use, or transfer licensed material so as to release to an unrestricted area radioactive material in concentrations which exceed the limits specified in Appendix B, Table II of this part .... For purposes of this section, concentrations may be averaged over a period not greater than one year." Even if a mill's license does not require sampling at the site boundary of maximum concentration, a sample may be necessary to demonstrate compliance with 10CFR20. Most mill personnel are painfully familiar with 40CFRl90.10, which states: "Operations.... shall be conducted in such a manner as to provide reasonable assurance that: (a) The annual dose equivalent does not exceed 25 millirems to the whole body.... of any member of the public as the result of exposures to planned discharges of radioactive materials, radon and its daughters excepted... from uranium fuel cycle operations..." This means a licensee's sampling program must give "reasonable assurance" that the member of the general public receiving in the most exposure gets no more than 25 millirems per year. The sampling program necessary to provide that assurance may or may not be a license requirement. However, merely meeting the license requirements and the explicit regulatory requirements does not necessariarly ensure an adequate effluent and environmental air sampling program. The second objective of the environmental air sampling program, is to 2) [identify the source(s) of contaminants]. This will include not only the routine program, but special sampling for verification of sources and nonsources. Only after sampling can a mill operator be assured that roof vents, laboratory hoods, and other localized ventilation systems are not making a significant contribution to environmental releases. An environmental sampling program should also allow the mill operator to fulfill the third objective, to 3) [estimate exposures]. Even before 40CFR190, a sampling program should have provided the mill operator with the information necessary to determine the dose to the "fence post" person, or at least to determine if doses were well below the 10CFR20 limits previously allowed. The program should 4) [detect and measure unplanned releases]. If there is a fire, a scrubber failure, or if a drum of yellowcake breaks open, measured releases will almost always be lower than conservative estimates. Whether or not a system to provide sampling during accidents is needed is almost always a cost-benefit decision. In general, uranium operations do not sample just in case an accident may occur. Yet they may decide on continuous air sampling in lieu of intermittant sampling partially because of the potential for accidents. Another objective of air sampling is 5) [to provide information on the effectiveness of control systems]. This is always a concern with new or modified equipment and may dictate sampling frequency in other situations as well. For instance, if a small leak in a bag filter cannot be detected by other means, then more frequent stack sampling may be indicated. A routine effluent and environmental monitoring program should also fulfill the sixth objective,

Jan 1, 1981

By G. P. Salas

I.- In order to keep pace feeding its fast growing population, Mexico with only about 20% of its surface suitable for intensive agriculture, will need the application of modern foodgrowing techniques. To assure greater crop yields it will be necessary to apply more fertilizers than used at present (yearly average of 29 Kgs/hectare)** For its fertilizers production Mexico still depends mostly on imports of phosphate concentrates from Florida, U.S.A., Morocco and Spain. To reduce or eliminate this dependence on foreign providers, the Consejo de Recursos Minerales -a Federal Government exploration Institute- started in 1974 an exhaustive exploration program for phosphate deposits more amenable to commercial exploitation than the phosphatic limestones contained within the La Caja Formation of Upper Jurassic, found along the Sierra Madre Oriental. After studying literature on the origin and deposition of marine phosphate and visits to deposits in Florida, U.S.A., the Baja California peninsula was selected as most favorable for starting this program because of its geologic and sedimentary history and also for its geographic location, where the cold California and warm Counterequatorial currents meet. Exploration activities executed by FORNOS, S. A. (1956) led to the disco very of low grade phosphate (3 to 5% P2O5) in the recent beach sands along the Bahia de Magdalena (Fig. # 1). In his doctoral thesis Bruno D'Anglejan Chatillon (1965) reports the presence of nodular phosphate on the continental shelf, between Isla Margarita and the Vizcaino peninsula. He estimated reserves of up to 1.5 million tons. A Mexican-American marine exploration company attempted in 1966 the evaluation of this deposit with negative results.

Jan 1, 1978

By R. W. Smith

A number of investigators have studied the electrokinetic potential (?) of kaolinite as a function of pH. (1,2,3,4,5) These investigators all agree that the ? is negative except at quite acid pH values. The actual shapes of the curves reported by the several authors vary considerably. In spite of the general negative character of kaolinite the mineral has a rather high anion exchange capacity. (6,7,8) The cation exchange capacity is the lowest for the clay minerals. (6) It has been shown that anionic surfactants adsorb readily onto the mineral even up to neutrality, often in quantities exceeding the reported anion exchange capacity. (7,8) At least part of the anionic adsorption should be onto positive edge sites thought to exist on the mineral. (9,10) In the present study ? of kaolinite was measured as a function of pH using both the streaming potential (sp) and microelectrophoresis (m.e.p.) methods. In addition ? was measured at various pH values as functions of sodium dodecyl sulfate (SDS) and trimethyldodecylammonium chloride (TMDAC) concentrations. In some experiments decyl alcohol (DA) was added.

Jan 1, 1968

By W. D. Gould, . W. Koren, P. Bedard, P .. B. Marchant

Ammonia and nitrate in metallurgical operations arise from several sources: (1) the use of ammonium nitrate based explosives, e.g. ANFO; (2) the use of cyanide for gold extraction which is degraded to ammonia by most cyanide destruction techniques; and (3) the use of nitrogenous reagents in the mill for neutralisation, flotation and extraction. The concentrations of ammonia and nitrate in effluents vary from 10-50 ppm and 25-300 ppm respectjvely. A number of environmental problems are associated with both ammonia and nitrate. Both of these forms of nitrogen can contribute to the eutrophication of receiving waters. Ammonia and organic nitrogen can also cause high dissolved oxygen demands in receiving waters. Ammonia is also toxic to fish, particularly at elevated pH values. Several methods are in use for the removal of ammonia and nitrate from municipal wastewater, industrial effluents and agricultural runoff. To date, no treatment systems have been developed specifically for the removal of nitrogen from mine and mill effluents. This paper will report on some removal techniques that have been tested using actual and synthetic mine effluents.

Jan 1, 1993

By Frederik P. Agterberg

Mineral exploration consists of the acquisition of data and their interpretation to ascertain the presence or absence of uncertain events. In general, the amount of uncertainty decreases during exploration when targets become increasingly well defined. Decisions on further exploration and whether or not mining should be commenced are based on new information using both objective facts and subjective reasoning. Computers play an important role during all stages of exploration. Three recent books (References 1-3) on decision-making in exploration and mineral-resources evaluation provide additional background supplementing the papers in this volume and articles in scientific journals or other conference proceedings (e.g., References 4 and 5) dealing with the subject. Other new developments to be considered are that microcomputers are becoming increasingly important in the earth sciences (Reference 6), and so are applications of artificial intelligence (Reference 7). Microcomputer- based technology allows rapid communication between field parties and main office. Expert systems are becoming increasingly sophisticated aids for mineral exploration an can now contain objective rules based on statistical theory (Reference 8).

Jan 1, 1989

By Greg Joachims

Composition of salt in the Permian Flowerpot Shale in northwest Oklahoma suggests that the salt in this formation was deposited in the early phase of solar evaporation. Brine produced through natural dissolution of the subsurface salt has netted very pure brines, with relatively low concentrations of magnesium salts that should result from late-stage precipitation of salt deposits from sea water. Over the last 100 years, extensive studies of sea- water evaporites, in relation to brine density, have been a topic of discussion. The development of evaporation models has facilitated the increased production and purity of solar salt (salt produced through evaporation of brine by the sun's energy). Conversely, this information can be utilized to gain an understanding of how rock-salt formations were precipitated from sea water by analyzing the elemental constituents of the rock salt and of the resulting brine. By evaluation of well-documented, phase-curve tables of sea-water evaporation, a basic theory can be formulated on how the Flowerpot salt unit was formed.

Jan 1, 1999

By G. S. Dobby, N. J. Contini, S. W. Wilson

Scale-up and simulation of flotation columns requires construction of mathematical models which employ, as a minimum, rate constants for quantifying particle recovery in the collection zone as well as split factors for quantifying froth zone performance. To date, measurement of these rate parameters has proven to be difficult, due to the interdependent nature of the collection and froth zones. This paper describes a technique for making these measurements. The method requires recovery data from two modes of operation: countercurrent and cocurrent. In cocurrent flow slurry is fed at the bottom of the column and tailings are withdrawn a short distance below the froth interface. Countercurrent mode is conventional operation. The critical difference is that particles which are dropped out of the froth in cocurrent mode are immediately lost to tailings, while in countercurrent mode the particles are subjected to recollection. Fitting of the measured recoveries to the equations that describe flotation in the two modes yields rate constant or recovery values for both the collection and the froth zones.

Jan 1, 1988

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

Australia is a hub for mining technology development. The paper describes many of the key players involved in mining research in this country along with some of the interesting research outputs to emerge over the past decade.

Jan 1, 2010

By L. C. Lang

Effective and profitable mining begins with good blasting results. While the importance of sufficient energy to break the rock is recognized, more attention should be paid to the time factor in blasting. Fragmentation, looseness and the shape of the muckpile can be improved and energy levels lowered through the use of proper delays. The long delay is also the most important parameter in establishing stable walls along the final limits of the pit. The time factor in blasting is explained through the rock acceleration process and its practical application is demonstrated by case histories.

Jan 1, 1981

By Dennis A. Beiter, William J. Francart

Barometric pressure changes have been an important consideration in the sealing of mines, especially in the case of mine fires. These changes are caused by storm fronts and regularly, on a daily basis, by atmospheric heating and cooling. In many cases, anticipation of these fluctuations in a mine sealing operation or recovery can be an important consideration when scheduling activities. The barometric pressure changes create pressure differentials across sealed areas, inducing airflows which may create explosive mixtures of mine gasses, cause intensification of fires, and create irrespirable atmospheres outby seals. These effects of barometric pressure fluctuations on mine fire sealing and recovery operations are discussed. Data available from the National Weather Service is also discussed as a tool for predicting barometric pressure changes.

Jan 1, 1997

By K. Ohga

Japan has produced 14-16 million tons of coal per year in the past several years. About half of the production comes from eight coal mines in the Ishikari coal field, Hokkaido. Most of the gassy coal mines are in this field and the average mining depth of these coal mines has already attained about 700 m from the surface. Therefore, most of the coal mines have suffered from occurrences of coal and gas outbursts. To prevent outbursts and to reduce ventilation air, gas drainage has been carried out at all of these coal mines and these have had successful results. However, the methods of gas drainage differ from mine to mine. In this report, an outline of the main methods of gas drainage are described.

Jan 1, 1987

By Bryant Fitch

This paper will review thickening theory, from the ( ) of the practicing engineer, with particular emphasis on ( ) uncertainty or disagreement. It will attempt to outline broadly what we know and what we don't know. This should serve two purpose First, it will warn the process engineer where he might get into trouble. At least it will alert him to the risk involved in uncritically accepting any of the recommended design procedures. Second, it will identify for researchers some areas in which further work might be fruitful. Not too many years ago there would have been little to write on such a subject. We had been designing thickeners for decades, using the classic Coe and Clevenger procedure. As far as we were generally aware, they all turned out to be about the right size. And so if there was anything we didn't know, It certainly wasn't hurting us much. Today we know better. While it is true that in most cases units designed by the Coe and Clevenger procedure (1) will perform satisfactorily, we now know of cases in which they don't. And during the past few years there have been many developments and advances in basic thickening theory. So there is now a lot more room for disagreement, and a whole lot more to be uncertain about. What is "thickening" "Thickening" means different things to different people. For this paper we define it to mean sedimentation behavior characterized by line settling. Solids subside with a clear line of demarcation between settling solids and supernatant. Although the supernatant will usually be clear, in some cases it may be turbid. Line settling must entail that all particles just below the pulp-supernatant interface have the same subsidence rate, so that

Jan 1, 1971

By Stuart Hammer

The mining industry has seen a flurry of merger and acquisition activity of late. Rising metal prices, increased spending on infrastructure in developing nations and the growing demand for companies to diversify have helped fuel M&A activity in this industry. Many analysts believe that the robust M&A activity will continue, particularly if the demand for mineral resources in India and China remains strong. Because prospective purchasers need to evaluate the various risks confronting target companies, acquiring mining companies requires a considerable amount of due diligence. Of these risks, environmental risk is critical and warrants significant analysis. The failure to properly assess environmental risks associated with remediation, reclamation, compliance or litigation can undermine the transaction. Such assessment is a difficult endeavor, however, due to several challenges that companies face when assessing environmental risks. To make matters more complicated, despite these challenges, many sellers ask buyers to assume all environmental risks with limited post-closing indemnification rights. This article addresses the most significant issues that commonly arise when conducting environmental due diligence and allocating environmental risk in connection with M&A transactions in the mining industry.

Jan 1, 2008

By Boris M. Vorobjev

The paper in question discusses a wide range of topics related to computerized coal mine monitoring systems starting with the history of development and application of computerized monitoring coal mine systems and finishing with modern trends in the design and updating of such systems. The paper focuses exclusively on methodological and technical aspects of computer-based coal mine monitoring systems and their applicability in both surface and underground coal mining operations.

Jan 1, 1989

By Brij M. Moudgil

Lack of understanding the major process parameters and inadequate scale-up factors have led to the belief that fundamental knowledge is not important for successful flotation plant operations. Flotation of simple and easy to process ores may not require a strong fundamental knowledge base for day to day operations. However, as low grade complex ores are mined and process control is integrated into flotation schemes, it is imperative for a plant operator to acquire a strong background in the basics of the flotation process at hand and/or have access to such a knowledge base at short notice. In order to meet the challenges of unexpected changes in the feed, reagent quality, water chemistry, physical, mechanical and hydrodynamic conditions, the flotation plant superintendent/chief metallurgist must have a strong background in the flotation fundamentals.

Jan 1, 1993

By Noel N. Moebs, John L. Ellenberger

Geologic structures in mine roof rock contribute to many roof falls in Appalachian coal mines. These structures include paleochannels, scours, pinch-outs, slickensides, clay veins, and cravasse splays consisting of thinly interlaminated sandstone and shale. These structures often can be identified during, and sometimes before, development and mine projections can be revised to reduce the adverse effects of discontinuities in roof structure. Large areas of roof consisting of laminated sandstones or incompetent strata generally can be delineated from exploratory drill-hole data and the need for supplementary support can be anticipated. Because an accurate description of roof geology also provides some indication of optimum length and type of roof bolts that should be installed, this Bureau of Mines paper describes the hazardous roof structures most commonly encountered in the Appalachian coal region.

Jan 1, 1982

By Dennis J. Lachel, Lloyd B. Underwood

In recent years a great number of papers have been presented at symposiums and have appeared in the literature relative to geologic prediction for rapid excavation and tunneling. Many of these papers describe research projects now underway to investigate tunnel site selection by remote sensing techniques, seismic holography, electro¬magnetic pulse sounding, optical scanning for structural features, and many other exotic geophysical techniques. While it is possible that this research will produce techniques that may prove to be very useful, it appears for the present at least, and perhaps for another decade, that there still will be no substitute for conventional exploration methods such as coring boring, geologic mapping, studies of existing wells, and proven geophysical techniques. Nevertheless, there is still room for tremendous improvement in the conventional techniques for geologic prediction in tunneling. These include: more rapid and accurately aligned coring borings drilled parallel to the tunnel alignment; improved geophysical surveys both prior and during construction; improved methods for predicting ground¬water inflows and water pressures, both of which can greatly influence the cost of driving tunnels. Geophysical techniques can also be ap¬plied to locate deeply incised glacial troughs or ancient buried stream channels that might cross the tunnel alignment. In the meantime, while some researchers continue their efforts to¬ward a breakthrough in new techniques for geologic prediction, it is recommended that other researchers direct their efforts toward sol¬ving specific problems such as accurately predicting ground-water conditions, determining locations of high geostatic stresses, and locations of major fault and shear zones.

Jan 1, 1997

By C. E. Roessler

Uranium and its decay series are associated with phosphate deposits of marine origin. Uranium concentrations are on the order of 100 to 200 ppm in matrix from the Bone Valley formation of Central Florida and about 25% this value in matrix mined from the Hawthorne formation in North Florida. Occupational radiation exposure due to this source has been under study in Florida since the mid 1970's (Windham, Partridge, Horton 1976; Roessler and Prince 1978). This report is based on findings of an industry-wide scoping survey conducted by the University of Florida during March 1976 through May 1977 and subsequent studies in selected individual facilities. PHOSPHATE MINING OPERATIONS Mining and beneficiation operations are diagramed in Figure 1. At the excavation site, electric powered draglines remove the overburden and expose the phosphate matrix (ore) which is then slurried and pumped to the beneficiation site. At the washer stage of the beneficiation plant, the matrix is subjected to washing and screening. A coarse product, "pebble" is produced and sent to storage piles while the fine fraction is passed through a series of cyclones to remove the clays. The generated clay suspension is sent to settling ponds while the remaining sand-sized fraction is sent to the flotation plant. At the flotation plant, phosphate particles are recovered from the fine sand particles of similar size through several stages of treatment with reagents, agitation and separation of floating and sinking fractions. The high grade concentrate produced is transferred to storage while the sand tailings are discarded. [ ]

Jan 1, 1981