Search Documents

By Michael J. Taylor

Introduction A prime goal in the design and operation of uranium milling waste or tailing disposal systems is to mitigate adverse effects of tailing liquid on the adjacent groundwater. Adverse effects are often defined as modifying the groundwater quality in such a manner as to have detrimental health effects on downstream users. To accomplish this goal, the following three types of systems are employed with regard to the seepage and groundwater aspects of waste disposal: Type I Systems Seepage is allowed to occur unabated from the tailing disposal facility. Detrimental radionuclides and chemical elements are prevented from causing adverse downstream effects by natural purification actions in the subgrade geologic materials and the near zone groundwater. Monitoring is required to assure the predicted natural purification is occurring. The consequences of seepage loss is minimal since the m be predicted with current investigation and analytical techniques and can be evaluated as to effectiveness during operations. Type II Systems Seepage is partially retained in a waste impoundment or leakage from a designed retention system is anticipated. Natural purification is relied on for controlling migration of detrimental radionuclides or chemical elements, or contingency planning is employed to collect and return the tailing liquid to the impoundment. Installation efforts and concern for escape of tailing liquid are greater than for Type I systems, but extra precautions to preclude all seepage are not implemented. Monitoring is required to detect leakage and/or assure the natural purification of escaping tailing fluid. The consequence for accidential excusions are moderate, and will be excessive only if massive system failure occurs. Type III Systems Seepage is totally restricted by a costly system constructed and operated with extra care. Natural

Jan 1, 1980

By Henry A. Russell

During the last ten years Parsons Brinckerhoff has become a leader in the area of tunnel rehabilitation. A significant part of any tunnel rehabilitation program is the control of groundwater infiltration into the structure. This leakage over time, causes deterioration of the structures, and creates numerous operational problems for the tunnel operator. This paper will address current procedures for identification, documentation, and recommendations of repair methods for the control of groundwater infiltration in rail and highway tunnels.

Jan 1, 1993

By Vicki Seppala

Phelps Dodge Mining Company operates some of the world’s largest open pit mines. Safely mining in these deep pits requires the commitment to a proactive integrated slope management process. The slope management process also includes the continued look for improved slope design, construction, and maintenance of slope faces. This paper discusses integration of such technology as electronic programmable detonators, 3D imaging using ground-based LiDAR scans, and reflectorless slope monitoring systems in a slope management program.

Jan 1, 2005

By Peter Joralemon

I want to limit my remarks to epigenetic ore deposits, but do not necessarily subscribe to the classic theories of hydrothermal ore deposition. I will consider an epigenetic deposit as a primary deposit in which the economic minerals have been introduced subsequent to the formation of the enclosing rock, regardless of the source. Past ore discoveries have been made to a great extent by prospecting techniques that have remained relatively constant over the last many decades. In many cases the discoveries have been enlarged or enhanced with the use of technical tools such as geophysics, but theoretical geology, which should serve as a foundation for exploration, has shown little progress of practical importance since the turn of the century.

Jan 1, 1967

By G. Thorsen

An alternative way to the normal practice of precipitation of jarosite, goethite, or hematite for removal of iron from zinc sulphate process liquors/ is to employ the techniques of solvent extraction. The process presented avoids the addition of any external alkali for the extraction of iron by integrating the leaching and solvent extraction steps in a hydrometallurgical zinc plant. By starting the leaching of zinc from the solid zinc calcine material with an organic solution of an acid liquid cation exchanger, the organic phase is loaded with the organic zinc salt from the direct reaction with zinc oxide. The residue from the organic leaching is transferred to a hot acid leach circuit where the remaining zinc oxide and the zinc ferrites will dissolve form¬ing an aqueous sulphate solution of zinc and iron. In the subsequent solvent extraction of iron from this aqueous leach solution, iron is exchanged with zinc from the organic phase. The commercial carboxylic acid Versatic 10 (Shell) is highly efficient for this integrated process of leaching and solvent extraction. The resulting iron-loaded organic phase is heated to 150-200 C in the presence of water whereby the iron will be directly precipitated from the organic phase as iron oxide of high purity and the regenerated organic acid is recycled to the organic leaching step for reloading with zinc.

Jan 1, 1980

By John P. Mahaffey

Thank you Mr. Chairman, Ladies and Gentlemen of SME-AIM? for this opportunity to talk to you about, one of the most interesting and challenging facets of our mining industry. Because the need was then -we built in 1964 what is still today, one of the most sophisticated AC mining machine simulators for this or any industry. It simulated the electrical controls and circuits of an AC shuttle car. The student activated the controls on the main console, which represented the elementary control and power circuits. Its accompanying slide-tape program, student manual and worksheets provided our customers with an effective and highly motivational means to teach their face mechanics: 1. practical AC circuit and motor theory 2. print reading 3. troubleshooting techniques Nearly 10,000 men have put in over 100,000 manhours of training on the AC panel and its DC counterpart. The DC panel was modeled after the 14BU10 Loader. The success of these larger panels pointed out the need in our industry for an orangized, basic electrical program designed around mining machinery components & circuits. But probably more importantly, they brought to light the tremendous thirst for upgrading by our industry's employees. We then turned our attention to developing programs around very basic panels. The resulting programs were designed also to assure maximum student involvement.

Jan 1, 1975

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor --will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Jan 1, 1997

By James K. Kindig

Solvent extraction as a method of purifying and concentrating metal values from solution has become a standard hydrometallurgical operation for recovery of both uranium and vanadium, and within the past two years it has been put into operation in a commercial plant for recovery of copper from leach solutions. In this first full scale solvent extraction plant for recovery of copper operated by Ranchers Exploration and Development Corporation near Miami, Arizona, a kerosene solution of an organic compound, LIX-64® is used to selectively extract the copper from the dilute acidic copper sulfate leach liquor obtained from heap leach operations. The copper is back extracted from the solvent into a stripping solution which is fed to an electrolysis circuit producing cathode copper for sale.

Jan 1, 1970

The importance of factoring mining dilution into the estimation of ore reserves in an open pit mine is discussed. An example that relates the issue of mining dilution to the size of the smallest volumes that can be mined selectively is given. The relationship between the size of the selective mining units (SMUs) and the variance of their average grade is presented. The concept of variance reduction and its use in factoring mining dilution into geostatistical ore reserve estimation is described. An approach to estimate a variance reduction factor by way of conditional simulation is introduced.

Jan 1, 1998

By L. C. Morales

Mexico has an area of about 2 million km2 (772,260 sq miles), with volcanic activity, large shores and mountainous areas reaching as high as 6000 m (19,680 ft) above sea level. These conditions are favorable for most mineral deposits, some of commercial value and others as a source of mineral samples. In addition to its vast mineral wealth, Mexico has another valuable asset in its people. Even before the discovery of America, natives were successfully mining metals. During the colonial days, the mineral deposits were mined to increase the wealth of Spain. All this experience was passed from generation to generation. It created a tradition of mining and minerals processing engineers that currently accounts for about 182,000 people supported by mining-related activities. Nonmetallic minerals in Mexico have been mined by natives since the early days. They knew the value of kaolin clays for pottery, as evidenced by archeological findings. This experience was also passed from generation to generation and has become recognized worldwide as ceramic wares of high quality. The Talavera ceramic from Puebla is an example of family traditions many generations old.

Jan 1, 1994

By Karl J. Ellefsen

A geophysical investigation can provide valuable geologic information needed to characterize sand-and- gravel deposits and can be an attractive complement to more common characterization methods such as drilling. Although such investigations have been conducted already, a comparison of the different geophysical methods used in these investigations apparently has never been done. For this reason, a study was initiated by the Mineral Resources Program of the U.S. Geological Survey to determine the advantages and the limitations of different geophysical methods when used to evaluate alluvial sand-and-gravel deposits. The study is focused on those geophysical methods that are commonly available, because these are most likely to be used by industry. Furthermore, the study is focused on surface geophysical methods. Heretofore, four different methods have been evaluated. Three of the four methods-time-domain electro-magnetic (TEM) soundings, frequency-domain electro-magnetic profiling, DC-resistivity soundings-are similar in that they all measure the electrical resistivity of the ground with depth. Ground-penetrating radar, however, maps changes in the dielectric permittivity and for the electrical resistivity with depth. For all, four methods, the objective is to relate the measured physical quantity to the stratigraphy of the alluvial sediments.

Jan 1, 1999

By Gopalan Ramadorai

This paper presents a review of halogen solvents used in the processing of precious metals. Reagents of widely varying chemical structures, such as chlorine gas, calcium and sodium hypochlorite, chlorine dioxide, iodine and bromine have been used for precious metal extraction. None of these chemicals are a replacement for cyanide: however, each of these chemicals present an opportunity for use in processing a specific type of ore. The ore and chemical must be matched to each other for success. Recovery of metal from the leach solutions also offers challenges.

Jan 1, 1994

By L. B. Rothfeld

Two new coal use technologies are on the verge of commercial acceptance by the utility industry: atmospheric fluidized bed combustion (AFBC) and gasification combined cycle (GCC). Generating plants under construction or in planning will replace older pulverized coal (PC) boilers or substitute for new PC boiler capacity. This paper reports recent developments in the commercialization of AFBC and GCC, emphasizing the potential impact on the coal mining industry. The influence of coal quality characteristics on fuel selection is explored by means of preliminary economic calculations for different coals and competing fuels.

Jan 1, 1987

By Pradip

Chelatang agents, because of their metal specificity, can function as effective mineral processing reagents. A brief review of the work carried out in this area is presented. Some of the salient features of mineral flotation and flocculation with chehting-type reagents, such as bulk us. surface chelation, the role of pH, mineral solubility, solution chemistry of reagents, and temperature, are illustrated with appropriate examples. The problems associated with the commercialization of chelating reagents for ore beneficiation and the research efforts required in this area are also discussed.

Jan 1, 1987

By Raquel Costa, Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, Ana Filipa Marques, Andreia Afonso, Maria Ana Martins, António Calado, Luísa Pinto Ribeiro

Since its formation in 2004, the Task Group for the Extension of the Continental Shelf (EMEPC) has been collecting hydrographic, geological and geophysical data to support the extension of the continental shelf beyond 200 NM. In 2008, the EMEPC acquired a 6,000 m rated ROV named "Luso" and has been cooperating with several national and international institutions to increase and improve its operational capabilities to conduct research on deep-sea minerals. The Portuguese continental shelf corresponds to a broad area of the seafloor encompassing different physiographic domains: the mid-Atlantic ridge system, abyssal plains and numerous seamounts. From 2008 to the present, the mid- Atlantic ridge and seamounts have been the most visited sites with the ROV "Luso". Several hydrothermal vent sites are known to occur along the mid-Atlantic ridge to the south of the Azores archipelago and mostly within the Portuguese EEZ. Vent fields were also discovered in the extended continental shelf, namely the Rainbow and the Moytirra sites located to south and to the north of the Azores archipelago, respectively. The most studied seamounts correspond to those forming the Great Meteor chain and the Madeira- Tore rise. All these visited sites are related either with the occurrence of polymetallic sulphides or cobalt rich Fe-Mn crusts and the opportunities to further pursue their exploration will be discussed.

Sep 1, 2014

By Lorraine B. Burgin

The extensive lead time to develop most Arizona copper deposits commenced with initial production efforts before the turn of the century, when the first attempts were made to recover gold and silver and later copper from the high-grade vein deposits of the territory. Each of these discoveries, prospects, and early operations had its own lead time and life cycle as economic production was attempted. Because prices of the metals fluctuated and the higher grade material was depleted, economics forced operations to close and companies to fail. Renewed interest in the property because of improved conditions, different interpretation of the geologic structure, or new promotional ability frequently resulted in the formation of yet another company to finance the exploration and, hopefully, the development of the property. This cycle of renewed activity and subsequent abandonment was and is common, accounting for many lead times and for the long period of time from the initial location of claims to large-scale production. In order to gain a perspective on the lead-time interval necessary to achieve development of a large-scale operation, the histories of several major Arizona mines were examined, rather than a simple listing of discovery and production dates of many mines to arrive at a statistical average. The Miami, Castle Dome, Copper Cities, San Manuel, and Twin Buttes properties were studied, and as much data as possible obtained on the Pinto Valley, Esperanza, Sierrita, Pima, and Mineral Park-Ithaca Peak properties.

Jan 1, 1974

By Bill S. Taylor

Dutch State Mines [D.S.M] introduced the Heavy Medium Cyclone into the United States for cleaning fine coal about three decades ago. Since that time the general industry practice has been to deslime the raw coal at 28 Mesh (0. 59mm) size. The plus 28M material is fed to the Heavy Medium Cyclone for cleaning, and the 28M x 0 fraction is processed by other means (e. g. flotation or hydrocyclones). This approach recognized that 28M was the smallest size particle that could be easily rinsed on vibratory screens without excessive loss of magnetite, and without blinding of sieve bend and vibratory screen decks. Another reason for the 28M de-sliming was to avoid excessive contamination of the media with non-magnetic coal, shale, or clay fines. The most undesirable of these contaminants is the sub-micron size clay particles (2) that greatly increase the viscosity of the media and reduce the numerical maximum level that the media specific gravity can obtain due to the lower specific gravity of clay with respect to magnetite. The higher the fugitive clay content, the more severe the preceding problems become. During the last 30 years, many conventional Heavy Medium Cyclone Plants have been built throughout the world. In the United States, the initial cyclone plants were confined to the production of high quality metallurgical coal where lower gravities of separation were required than could be obtained from the conventional hydraulic or air separation processes. In recent years a large and ever-increasing number of preparation plants producing steam coal have started utilizing Heavy Medium Cyclone technology due to the environmental pressures being encountered to produce low sulphur coal. Due to the inherent characteristic of many coals of having a lower pyritic sulphur content at lower specific gravity fractions, many applications and markets are appearing for separating steam coals at much lower specific gravities than have been historically normal in the United States. Therefore. Heavy Medium Cyclones are being utilized to a much greater degree in this field, due to the flexibility of low separating gravity ability coupled with high efficiency when high percentage of near gravity material is present.

Jan 1, 1978

By P. G. Martin

"As the speed of business has continued to increase over the last decade, the focus on real-time control of the performance of both stationary and mobile assets has become an increasing priority. Traditionally the maintenance team has been focused on the management of the availability of assets while the operations team has been focused on the throughput of those same assets. Typically operations and maintenance teams worked almost independently in spite of the fact that they were both working with the same assets. Part of the problem has been their traditional performance measures which have often been diametrically opposed. Recent advancements in the area of real-time performance measures and decision support have helped to drive higher levels of collaboration between operations and maintenance leading to real-time asset performance control and higher levels of business performance. This paper will explore the forces driving the need for changes, present an effective approach to the definition of the most appropriate business performance measures, and examine the effectiveness of contextualized real-time decision support resulting in asset performance control. TRADITIONAL APPROACHES TO ASSET PERFORMANCE MANAGEMENT In most industrial operations the phrase asset performance management is synonymous with maintenance of the industrial assets. This is the way industry has viewed asset management and asset performance management for decades. This is a very limited perspective that is serving to constrain the profitability of industrial operations. As industrial organizations began to form following the Industrial Revolution, the complexity of the operations forced an organizational design based on specialization. No single person could understand all of the aspects of an industrialized operation. This was particularly true at the plant floor level where the operation and maintenance of the industrial equipment required very different skillsets and training. To accommodate the vast differences most industrial organizations set up operations teams to run the equipment and maintenance teams to keep the equipment available to the operation. Both teams were dealing with the same industrial equipment but from very different perspectives and with very different performance measures. Typically the operations team was measured on maximizing the output of the equipment – or throughput. On the other hand the maintenance team was measured on the uptime – or availability of the equipment."

Jan 1, 2015

By W. P. Stroud, R. S. Dennen

A ground penetrating synthetic pulse radar system has been used by the US Bureau of Mines to probe into a coal pillar to locate hidden structures or anomalies. Direct matrix inversion was used to obtain a velocity image of the interior of the pillar. The reconstructed image showed the existence and location of a relatively low velocity material within the pillar. Core samples were taken from the pillar in a region surrounding the low velocity material. Analysis of the cores showed the presence of a clay vein coinciding with the low velocity material imaged in the tomogram.

Jan 1, 1992

By G. R. Denham

Innovative designs, mining, construction and reclamation practices are used at PT Newmont Nusa Tenggara's Batu Hijau mine on Sumbawa Indonesia to develop a cost-effective, environmentally sound, stockpile and dumping system. The mine production rate is over 200 million tonnes per year (50 million tonnes processed with 150 million tonnes being stockpiled for processing later or placed in waste dumps). Dump development for over 150 million tonnes per year in a mountainous, tropical environment, while meeting environmental and permitting requirements is not an easy task. The effective implementation requires innovative techniques and practices from every department of the mine.

Jan 1, 2002