Search Documents

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By N. Del Bel Belluz

Drilling underground in the Grasberg De-watering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are utilized; pilot-holes to probe ahead of the tunnel development to intersect aquifers ahead of the face; and de-watering holes to de-water rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, rates of 1050 psi static pressure have been recorded with flows from a NQ hole measured at 1350 gpm (US). The water flows can be slightly acidic, necessitating the use of stainless steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early to deal with these conditions. The collar gear is used to control water flows whereby the water is treated as an important resource. As a result, pm has established procedures to maintain safety of the drill crews, enable coring of the rock and to maintain safety of the miners who are driving the drifts.

Jan 1, 1998

By J. Andersen

The very large quantities of energy used for size reduction in the minerals processing industry necessitate the accurate prediction of comminution machine power draw for optimum plant design. The JKMRC has developed effective models for predicting ball mill, autogenous mill, semi- autogenous mill and crusher power draw. When combined with comminution models they provide a powerful tool for evaluating not only the size reduction performance of a plant design, but its power utilization efficiency as well. This paper describes the structure of the mill and crusher power models. Data from a wide range of equipment types are presented which illustrate the accuracy of these models.

Jan 1, 1992

By G. Robert Ganis

The folded Appalachians are a physiographic province of eastern North America extending from Nova Scotia to Alabama. The province strikes through the state of Pennsylvania (see Fig. 1) comprising roughly 20 percent of the state and it is here that the focus of this paper will attend. The province is a thick sedimentary sequence which was compressed into a folded mountain belt by the Appalachian Orogeny which terminated at the end of the Permian. The stratigraphy contains both carbonate and non-carbonate rocks as a reflection of the depositional environment at any specific time and place during the Paleozoic geosynclinal accumulation. Although a great deal of variety and difference exists in the geology from one end to another, a common thread of structural and stratigraphic style exists. Carbonate rocks, limestones and dolomites, comprise a substantial percentage of the total Appalachian stratigraphy and are interbedded with clastic materials such as sandstones, siltstones, and shales. The carbonate rocks are extensively mined and collectively represent a vast economic resource.

Jan 1, 1983

By Jorge A. Benitez Muro

Within the exploration programs carried on by the Consejo de Recursos Naturales No Renovables, the one with the largest coverage (more than 75, 000 square kilometers) is the northern Coahuila Exploration Project. Due to its nature, geochemical exploration methods were selected to obtain quick results. The program included essentially, three main stages : 1. - A regional geochemical stream sediment survey. 2. - Semi-detailed studies of the anomalous areas selected in the previous stage, and 3. - Detailed exploration of the promising areas. To the date, the first two stages have been completed, and the third one is being carried on. The work was started on september 1972, and it will probably take one more year before drilling can be started, but at the end of stage three it is expected that at least 5 important targets will have been detected. The regional work was conducted by 3 field crews, but the detailed program is being done by only one.

Jan 1, 1974

By Donald Lau, Adrian Crawford

In the field of grouting, practitioners fre¬quently advocate procedures that are often unique and contradictory. As a result there has been considerable debate as to what constitutes optimum grouting practice. A knowledge of both the rheological properties and the flow characteristics of grouts is essential to the development of a rational understanding of the grouting process. Flow models and viscosity experiments have been conducted using cement grouts comprising High Early Strength Portland and Microfine cements. The addition of superplasticizers was found to enhance the flowability of the grouts as well as to reduce the effective groutability ratio. Steady state flow equations and design charts for predicting the radial penetration of cement grouts have been developed.

Jan 1, 1986

By S. K. Kawatra

For efficient control of particle size in a wet grinding circuit, three alternative methods for monitoring pro- duct particle size are available. These methods are based on: 1. Ultrasonic wave absorption. 2. Low-angle forward scattering of a laser beam. 3. Inferential sizing techniques. The relative advantages and disadvantages of each technique are discussed. A particle size monitor can be used on a single grinding line to control the product particle size. To minimize the number of particle size monitors at an operation consisting of many similar grinding lines, a portable multi-stream on-line analyzer can be used. The paper outlines the design and the operational characteristics of the portable multi-stream online analyzer.

Jan 1, 1979

By Ahmet Gursoy

Maryland, will be the widest vehicular tunnel ever built by the trench tube method. Careful coordination and planning were required to meet the tight and fast design and construction schedules. During the preliminary design, traditional design drawings were bypassed in favor of 25 preliminary design reports representing major work breakdown structures (tasks). For each task, alternative design solutions were examined and analyzed by means of trade-off studies on the basis of engineering, constructibility, and economic considerations, thus providing an overall conceptual value engineering approach for the entire project. So far, total value engineering proposed by the contractor for Contract I I (largest contract of the project at $245 million) is less than 1.5 percent of the contract value. This is an important indication of the success of the design phase planning.

Jan 1, 1983

By Donald R. East

For many years there has been increasing pressure on mining companies, not without some justification, to design tailings storage facilities which guarantee some degree of protection against process solutions entering local groundwater and surface water flows. A fairly straightforward approach to achieving this has been to design conventional water-retaining type structures, and this has often been reinforced by the need to store large volumes of process water and seasonal run-off within the tailings facility. The conventional design uses naturally occurring geological barriers and a conventional embankment with possibly a grout curtain, or artificial barriers around the entire facility, using either imported low permeability soils, admixtures, or synthetic liners. While these approaches may achieve the primary objective of minimizing seepage, various other factors should be considered. Firstly, by depositing the tailings slurry in a sub-aqueous manner, the tailings, especially if relatively fine grained, will settle to very low densities and little or no on-going consolidation may occur over the operating life of the mine, There have been many cases where measured pore pressures within the tailings mass equal the total overburden stress, i.e., no consolidation and no strength, many years after decommissioning.

Jan 1, 1998

By Dave Willis

Two hundred and thirty million tons of coal! That is what the Burlington Northern (BN) railroad anticipates that it and the Chicago North Western railroad (CNW) will haul out of the southern Powder River Basin l (see map on page 966) in 1994. Put that 209 Mt (230 million st) into railroad perspective. Current average train size is 113 cars. With each car transporting 94 t (103.5 st) of coal, each train averages 10.6 kt (11,700 st) of coal. Simple division shows that 209 Mt (230 million st) of coal equals 19,658 trains a year. So BN and the CNW must move 54 loads a day out of the Basin. Every load, of course, has an empty side of its cycle. This means that 54 loads a day translates into 108 total trains a day, or 39,420 trains a year through the southern PRB.

Jan 1, 1994

By M. T. Holroyd

Digital computer applications to minerals exploration remained largely an experimental alternative to manual techniques until well into the 1960's. Due to the high cost of computer time, and the lack of digital data and appropriate software, the most favoured applications in the early days were computationally intense tasks - those which produced the most results with the least demands for programing and data input, e.g. forward modeling. When large digitisers and plotters became affordable, the computer took over simple labour intensive tasks such as data transcription, and when software caught up, more complex tasks such as contouring. Digital data acquisition systems and superminicomputers made total computerisation of geophysical compilation and cartography possible and affordable. Applications continued to develop into areas of much greater logical complexity. Software, the new labour intensive process, still lagged behind. The microcomputer made computer applications potentially available everywhere to everyone. Desk-top micros as powerful as the minis of ten years ago can take on any geophysical exploration task currently done by computer - when the software becomes available.

Jan 1, 1989

By Zoltan F. Oszter

Feeding bulk solids from bins or bunkers sometimes poses a problem to the materials handling engineer. The paper describes, by practical examples, how material flow can be improved on existing installations, and how difficult-to-handle materials can be successfully drawn from storage and fed to fully automated process systems. The examples illustrated are based on actual experience with projects designed for the mining and metallurgical industry. Maintenance costs, where available, are also indicated.

Jan 1, 1966

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department's Bureau of Mines.

Jan 1, 1984

By Madan M. Singh

Although roof bolting has been a major means of strata support for nearly two decades, little attention has been directed towards the design of bolt Installations. The variables involved are interdependent and their study complex. However, some simple tests may be employed to serve as guides to the efficient design of roof bolt systems. Local conditions are continually varying and are important to pattern design. This paper discusses such considerations and suggests techniques which may be employed to effect improved roof control with bolts.

Jan 1, 1967

By A. K. Gangopadhyay

This paper discusses the effect of grinding media composition, mineral type and slurry environment on the wear rate of various grinding media (balls). Sufficient wear data have been obtained and correlated with the modes of wear determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1984

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By M. J. Shulman

An algorithm used by the US Coast Guard to find lost objects is utilized to optimally allocate exploration efforts during initial stages of an exploration program. Based on classical search theory, the algorithm assumes a target probability distribution function, a detection func¬tion, and a cost function. The three Junctions are analogous to delineating areas of possible mineralization, choice of exploration methods, and exploration budget. Application of the algorithm is shown for a hypothetical target distribution. Using the maximum number of field days available as the cost function, the optimal allocation of effort is shown for different exploration methods, e.g. electromagnetic survey and induced polarization. The adaption of the algorithm for the exploration process is discussed.

Jan 3, 1984

By A. Athousaki

The Ecological Footprint is a resource accounting tool used to address underlying sustainability questions. Aggregates consist of natural, artificial or recycled materials. The production of aggregates is the fastest growing activity worldwide since huge quantities are required by the construction industry. This paper presents a parametric investigation of the ecological footprint of transporting aggregates for urban use as a function of tonnage and distance.

Jan 1, 2008

By Truman Harrington

During the last decade, diesel engine manufacturers focused their research efforts on higher efficiencies and horsepower-to-weight ratios. The result was horsepower increases of between 20% and 30%. At the same time, coolant volume decreased by about the same amount. This has made coolant maintenance more important to ensure a long life for the engine and its cooling system. Due to dilution and additive depletion, supplemental conditioners are usually added to the coolant system during an oil change. Dilution occurs when coolant leaks from the system, and water or non-conditioned antifreeze is added. Depletion is a more complicated process that involves oxidation, neutralization, precipitation and metal surface reactions.

Jan 1, 1991

By D. Erik Spiller

Introduction The recovery of precious metals from ore can generally be accomplished using either gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems which employ leaching as the primary unit operation. A brief discussion of modern gravity concentration equipment is also presented.

Jan 1, 1984