Search Documents

By David C. Grant

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. Mter mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other chemicals (i.e., uranium and selenium) which are mobilized during the leach process, have also been found in the post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and thus greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid improvement in permeability.

Jan 1, 1982

By K. N. Han

The leaching behavior of palladium in ammoniacal solutions was investigated by using the rotating-disk technique in an autoclave. The study included the effects of rotation speed, temperature, oxygen pressure, composition of ammoniacal solutions and catalysts on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in terms of the thermodynamics and a kinetic model. Even though the Eh-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was very slow at temperatures below 100 °C but was significantly improved at higher temperatures. It was also found that the rotating speed of the palladium disk had no effect on the leaching rate. The apparent activation energy was found to he 69.7 kJ/mole. Based on the results obtained, it was concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1999

By Wilbur I. Duvall

This paper discusses general principles of underground opening design based on the concept that with the necessary input data regarding the geology of a site, the physical properties of the rocks, the in situ stress field in the rock and the general geometry of the underground openings, the rock formation can be classified into six major categories which are useful for design purposes. Using simple theories for the criteria of failure for rock In compression and tension, general elastic theory for stress concentration around openings and In structures, beam theory for stability of roof rock, and elementary inelastic theory for creep phenomena, basic design techniques are outlined for the various rock classifications. The need for field evaluation of the theoretical design is stressed and some general techniques that should be used in these field evaluations are discussed. Where appropriate, the need for additional studies and research is noted.

Jan 1, 1977

By Jerome E. Grader

Special-purpose analog computers are being profitably applied in the process industries to perform miscellaneoas online computing functions in situations where conventional measurement and/or control hardware cannot perform a required task satisfactorily. This paper will discuss the application of such equipment in the mining industry. It is divided into two parts, beginning with a description of operation of the hardware, followed by a discussion of several applications of the computers to mining industry control problems.

Jan 1, 1969

In addition to capital and operating costs, the accurate estimation of ore reserves is a key component to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by the improper estimation of ore reserves. The accurate estimation of an ore reserve relies heavily on an understanding of the geology and the underlying assumptions unique to the estimation techniques being used. These assumptions are reviewed, and the shortcomings of the estimation techniques and their possible impact on a given project's economics are discussed. The latest developments in geostatistics in overcoming existing reserve-estimation problems are presented.

Jan 1, 1998

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) remains a health concern in many underground metal/nonmetal mines, and has been regulated by the Mine Safety and Health Administration since 2002. While the NIOSH 5040 standard method for DPM monitoring is required to demonstrate regulatory compliance, the FLIR Airtec DPM Monitor can serve as complementary engineering tool. It is a handheld instrument that offers near real-time measurements. As part of an ongoing field study, the Airtec has been used to survey elemental carbon concentrations (a proxy for DPM) in an underground stone mine. Via “spot-checking” and more prolonged area monitoring, this effort was aimed at determining spatial and temporal DPM variation in several key locations. INTRODUCTION Diesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It is largely made up of elemental and organic carbon (EC and OC, respectively), which can be measured as proxies for estimating mass concentrations of DPM. The National Institute for Occupational Safety and Health (NIOSH) considers DPM to be a health hazard and potential carcinogen [1]. It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition, and retention in lung tissue [2]. Since DPM exists in both the micro- and nano-particulate ranges, it can surpass typical auto-immuno defense mechanisms that keep larger particles out of the respiratory system [2]. Relative to other occupations, the DPM exposure potential for underground miners is high because these individuals work in enclosed environments where diesel powered equipment is frequently used [3,4]. A variety of engineering and administrative controls have been devised to reduce DPM exposures in underground mines, and increased airflow is often a key component of control strategies. In large-opening mines, which are most common in the metal/nonmetal sector, DPM abatement via increased ventilation can be especially complex due to moving and controlling the large air quantities [5]. The Mine Safety and Health Administration (MSHA) has regulated DPM exposure in metal/nonmetal mines since 2002. The final rule limits personal exposure to total carbon (TC, which is the sum of EC and OC) to an eight-hour time weighted average (TWA) of 160 µg/m3. To demonstrate compliance, operators must use the NIOSH 5040 Method [6]. However, the Airtec DPM Monitor (FLIR Systems, Inc., Nashua, NH) was developed as an engineering tool to provide near real-time measurements of both EC and TC for tracking personal exposures [7]. The portable Airtec works by capturing DPM on a filter and successively measuring laser extinction on the filter as DPM accumulates; the EC fraction of the DPM is dark, and so as it accumulates the filter becomes darker and absorbs more laser light [8]. The laser extinction value is directly correlated to EC, but since EC and TC are generally observed in consistent proportions (i.e., TC = EC*1.3), the Airtec is also programmed to display TC as a TWA [9]. There have been multiple studies conducted to validate the Airtec and the instrument has been adopted by some mine operators as a tool for their health and safety programs [3,8]."

Jan 1, 2016

By Hans Hamrin

Three drill-blast cycles of 3.1 m advance achieved in one working shift of 7.5 hours at the Holsfjorden Tunnel project in Norway. The tunnel, 5235 m long, with a cross section of 8.6 m2, was completed several months ahead of schedule. This remarkable performance was achieved by a crew of 16 men, using machines specially designed for small tunnel excavation. The integration of drilling and charging into one unit, mucking and transport in another, reduced non-productive time considerably. The average cycle time of 140 min made it possible to complete three rounds in one 7.5 hours shift.

Jan 1, 1987

By V. V. Ershov

Mining geometrical graphic documentation is employed on a large scale in designing and planning of mining operations at all the stages of exploitation. Mining geometrical modelling of mineral grade distribution presents an independent type of mathematical (graphic) modelling. The idea of functional relationship between geological indices being observed, and spicier coordinates is the basis of traditional mining geometrical modelling. Graphic presentation of three independent variables P =f (x,y,z) is confined to obtaining the series of two independent variables functions. Independent variables are presented as topographic surfaces corresponding to plane cross-sections of a deposit. During exploitation of certain parts of a deposit the most reliable geological information is obtained, characterizing regularities of ore distribution in the entrails. This information is, though, not taken into account in goemetrization of the new areas. In this connection dynamic modelling of deposits in the process of exploitation is necessary, i.e. geometrization of the deposits should be dynamic.

Jan 1, 1986

By R. G. Reddy

Iron solubility's in spent pickling (HFHNO3 -H2O) solutions were determined as a function of HF and HNO3 acid concentrations. A chemical analysis of the industrial pickling solutions and sludges was performed. The stable phases observed in the sludges are FeF3.3H2O and (FeCr)F3.3H20. Pure Fe metal, AISI 316 stainless steel and AISI 416 stainless steel were used in this study. The results show, that the solubility of Fe increased as the concentrations of HF increased in the pickling solution at a fixed concentration of HNO3. A reasonable agreement between the experimental solubility data and the theoretical calculated data was obtained. X-ray diffraction analysis showed that the solid solubility product formed in the ternary solution containing pure Fe is mainly, at a high pH value, FeO(OH) compounds and, at a low pH value, Fe F3.3H2O compounds.

Jan 1, 1994

By N. Roqueñí, J. Loredo, F. Pendás

Impacts of mining on surface water and groundwater occur frequently not only in active mines but in abandoned mines, then the establishment of effective legal mechanisms for the regulation and control of mine waters is a necessary step in order to avoid pollution from mine waters and in consequence to contribute for a sustainable development of the mining industry. Currently there is a lack of a specific European legislation about mine waters and this absence of legislation occurs too at national level in many European countries. This absence of an European specific regulatory framework for mine water pollution questions the effectiveness and the applicability of the current legislation and this fact has led the EC to put forward proposals legislation to adequately deal with environmental and social consequences of mining, and among those proposals is a draft for a directive on waste from the extractive industry that includes provisions for mine water pollution.

Jan 1, 2005

The modelling process described in this paper was developed in order to assess the feasibility of various investments options for the exploitation of a lignite deposit located in the Prefecture of Florina, Greece. The model uses as evaluation criterion the net present value. It is based on the characteristics of the reserves and relates the decision making with numerous technical, economic and environmental factors. The examined alternatives include the construction of a new thermal power plant at the mine-mouth, the fuel supply of already existing power plants located at relatively long distances and the fuel exports in neighboring countries. Moreover, the feasibility of post-poning the exploitation of the lignite deposit and preserving its reserves for exploitation in the future is also assessed. The paper also includes a short discussion about the environmental constraints related to the supply of lignite produced from Florina mines to power plants that were designed and constructed for burning fuel mixtures with different quality characteristics.

Jan 1, 2005

By J. A. Finch

The photographic measurement of bubble diameter is tedious and restricted to vessels with transparent walls and relatively low bubble concentrations. A new method for predicting bubble diameter in a flotation column has been developed and confirmed by comparison with measured mean bubble diameter (Yianatos et al., 1987) Flotation columns are not mechanically agitated. This note describes an extension of Ms method to a mechanically agitated flotation machine. A recent publication by Szatkowski (1987) provided sufficient data to calculate bubble diameter by the proposed method and compare with values determined photo- graphically. Method In a two-phase system (gas and liquid), bubble diameter (db), superficial gas rate (Vg) and liquid rate (Vl), and gas holdup (Eg) are linked by two relationships (see the nomenclature at the end of the paper for definitions of symbols). [ ] Equation 1 is the definition of slip velocity (relative gas to liquid velocity) for a countercurrent gas-liquid system, and equation 2 is an adaptation (Yianatos et al., 1987) of the expression of Masliyah (1979) for hindered settling in a multispecies system. The solution for bubble diameter is by repetitive substitution of estimates of db in equation 2 until the calculated Ubs is equal to the measured Ubs in equation 1. Results and discussion Table 1 presents the data obtained by Szatkowski (1987) from a mechanically agitated laboratory flotation machine. The machine generated bubbles by directing a gas stream into the vicinity of a disk rotating at Ngh speed (up to 8000 rpm) in the flotation slurry. The air was completely dispersed in a swarm of fine bubbles. A photographic technique was used to determine the distribution of bubble size. The mean diameter and standard deviation were then calculated. Table 1 provides all the information necessary for computing bubble diameter (Vl is assumed zero). The calculated bubble diameter is presented in Table 1 as d;. Figure 1 plots measured versus calculated bubble diameter and shows reasonable agreement between values. There is an apparent tendency to undercalculate the small bubbles and overcalculate the large ones.

Jan 1, 1987

By Leland E. Paulson

The Grand Forks Energy Research Center and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons each of subbituminous coal and lignite were dried in a commercial scale dryer, oil sprayed and cooled, then shipped in open-top rail cars from Pekin, IL to Grand Forks, ND and stockpiled. Cars containing raw coal and dried coal that had not been oil sprayed were also transported for comparative purposes. The tests were conducted in August and November of 1974. The subbituminous coal was dried from 26 to 16 pct moisture and the heating value was upgraded from 8,420 to 9,650 Btu/lb. The lignite was dried from 39 to 22 pct moisture and its heating value was increased from 6,420 to 8,300 Btu/lb. Before loading subbituminous coal was cooled to 115° F and sprayed with oil at a rate of from 2 to 6 gal/ton. Similarly, lignite was cooled to 85° F and oil sprayed at rates of from 1 to 2 gal/ton. Both shipments arrived in Grand Forks with a minimum of difficulty. The subbituminous coal was subjected to 2 inches of rain during transit with no change in average moisture content. The cars containing dried and oil treated coal had less material lost to wind than either cars containing raw or untreated dried coal. With both dried lignite and subbitnminous shipments, a moderate increase in temperature was measured during transit. With the subbituminous shipments, ignition occurred near poorly fitted bottom dump doors, but was limited to a very small area. The dried lignite was shipped when ambient temperatures were below freezing, and frozen coal was noted around the edge of the car. At Grand Forks, the coal was stockpiled using proven techniques and has remained stable to this date.

Jan 1, 1975

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled- waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SB) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 1, 1984

By Bryce T. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 1998 at $534 million (28 percent of the total non-fuel mineral production of Utah). Major commodities produced in 1998 include: halite; potash and magnesium chloride; Portland cement; sand and gravel; car- bonates including lime, limestone, and dolomite; phosphate; crushed stone; clays; perlite; gypsum; and sulfur and sulfuric acid. Commodities produced in lesser amounts include: diatomite; pumice; silica; lightweight aggregate; gemstones, ornamental stone, and mineral and fossil specimens; byproduct sulfur and sulfuric acid; silica; and building stone. The years 1993 through 1998 were a period of steady growth in industrial rock and mineral production. However, some commodities have grown much more rapidly than others. The robust western U.S. economy has stimulated production of construction-related commodities like sand and gravel, raw materials for Portland cement, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants. Noteworthy specific developments include: (1) opening of new aggregate operations and buyouts of small aggregate operations by large national and international firms, (2) expansion of a lime operation and two cement plants, and (3) development of several new gypsum mines. The future of the industrial minerals industry in Utah looks promising despite a more restrictive regulatory environment and a growing anti-development attitude among its citizens. While Utah has become less pro-development than it was prior to the 1990s, it is still moderate compared to strongly anti-development states, so companies have some motivation to choose Utah in their strategic mineral development plans. As long as the western states' economies continue to grow, Utah's industrial minerals industry should thrive.

Jan 1, 2001

By Darrell V. B. . McClarty

In 1996, Rio Algom, Denison Mines and the Elliot Lake Research Field Station (ELRFS) formed a consortium to implement a regional environmental information management system (REIMS) for the Elliot Lake area in Ontario, Canada. ELRFS is an affiliate of Laurentian University in Sudbury, Ontario, The discovery of uranium in the Elliot Lake region in post-World War II led to the development of 12 mines and 11 associated mills between 1955 and 1958. During the late 1980s, declining world demand for uranium, combined with the discovery of high-grade uranium ore in other areas of the world, made the Elliot Lake mines uneconomical. As a result, all area mines ceased opera¬tions by the end of 1996. The eight facilities and three tailings management areas operated by Denison Mines and Rio Algom's five mining waste management areas contain 150 Mt (165 million st) of potentially acid-generating tailings. The areas cover 13.2 km2 (3,265 acres) and receive drainage from an additional 13 km2 (3,212 acres). The primary objective of the joint initiative was to implement a personal-computer-based, regional, environmental-information management system for managing historical data and ongoing environmental programs in the Elliot Lake region. The Elliot Lake consortium decided it needed an information system with an integrated, process-oriented and requirements-driven approach to collect and manage the environmental information. Following a study of environmental information management systems currently used by the mining industry, the consortium decided to base REIMS on the "Envista" product. This is a commercially available, environmental information management system marketed by Envista Technologies of Saskatoon, Canada.

Jan 1, 1999

By David Seymour

Precious metal producing mining companies in the United States, Canada, and South Africa were surveyed on carbon usage practices in the recovery of silver and gold. Responding companies represented CIP/CIL dperations, heap leach operations and combined mill/leach operations. Operational practices and carbon consumption rate measurements are presented, correlating consumption rates with process attributes. Precious metal producing mining companies in the United States, Canada, and South Africa were surveyed on carbon usage practices in the recovery of silver and gold. Responding companies represented CIP/CIL dperations, heap leach operations and combined mill/leach operations. Operational practices and carbon consumption rate measurements are presented, correlating consumption rates with process attributes.

Jan 1, 1992

By J. L. Weaver

The spiraling rate in phosphate rock demand during the period 1957 to 1967 led producers to expect a continuation of a high growth rate. Consequently they expanded production capacity to meet the expected demand. Both the domestic and the world demand has shown little growth over the past three years. Florida producers operating at less than 75% of installed mining capacity, produce all that their markets will absorb. We expect that the nest few years will bring only a slight improvement in this condition. An increased demand in the domestic agricultural market will be partially offset by a continuing erosion in the export market.

Jan 1, 1972

By Donald C. Trueblood

Since the Surface Mining Control and Reclamation Act (SMCRA) was passed in 1977, coal mine reclamation has been restricted from utilizing bluff-1ike features in permanent reclamation. This restriction is based on those provisions of SMCRA which require the elimination of all highwalls. In 1987, the Wyoming Mi ni ng Association began an effort to acquire the ability for coal mines to utilize bluffs in permanent reclamation for the purpose of enhancing the post-mining land use. The regulatory reform approach being uti1ized includes formation of a work group with members from industry, government, agriculture, and environmental organizations to prepare a proposal. Advantages of this approach are discussed.

Jan 1, 1989

By Zbigniew Hladysz

INTRODUCTION In the Polish coal mining industry, the Upper Silesian coal basin has an important position. It contributes over 98% of the total coal production of Poland which reached 193 mt in the year 1979. In view of the significant urbanized area in this region as well as the industrial potential, it is important to protect the surface by stowing the mined out underground workings. Approximately 18% of the total production is mined from longwall faces with stowing. However, caved longwall faces are most popular. In the upper Silesian coalfield, approximately 337 highly mechanized longwall faces are in operation. Out of these 337 faces, 301 longwall faces are caved. One of the main requirements for effective and safe coal extraction is a suitable method for strata control. We can divide the complex process of strata control into four steps: 1. Strata investigations 2. Selection of supports for roadways 3. Selection of supports for longwall 4. Rock bursts and other hazards protection STRATA INVESTIGATIONS Estimation of the structure and physico-mechanical properties of the rock mass surrounding the workings is an important constituent of strata control. These factors definitely influence the rock stability, support load, working conditions as well as the mining technology. Complex methods of strata investigations involve a set of indicators enabling the estimation of the stability of the roof rock, strength of the coal seam and load bearing capacity of the floor. The basis for the evaluation of roof stability for a coal seam is the classification according to the resistance to bed separation (1). The bed separation resistance is equal to the strength of the rock in tension perpendicular to the bedding plane. In order to properly classify a rock, it is indispensable to make continuous profiles of the bed separation resistance from the immediate roof up to a distance of three times the thickness of the coal seam. The profiles are developed by utilizing mine roof investigations with the hydraulic borehole penetrometer. (Fig. 1) The penetration resistance is determined by the critical pressure required to cause crushing of the rock by the penetrometer indentor (2). The classification of roof rocks and their ability to cave spontaneously during longwall mining is shown in [Fig. 2]. The measurement of the critical pressure also allows for the determination of the compressive strength of the rock, the index of workability and roof fissuration.

Jan 1, 1982