Search Documents

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By Z. Jin, D. DePaoli, P. Zhang

"Phosphorite, or phosphate rock, is the most significant secondary rare-earth resource. It contains high amounts of phosphate-bearing minerals along with low contents of rare earth elements (REEs). In Florida, about 19 Mt of phosphate rock are mined annually and most are used to manufacture fertilizers using a wet process, in which sulfuric acid reacts with phosphates to produce phosphoric acid and phosphogypsum. In the wet process, REEs are also leached out into solution and eventually get lost in the leaching residue and phosphate fertilizer. Recovering REEs from Florida phosphate rock in the wet process will be beneficial to broadening rare-earth availability, improving the quality of phosphoric acid product and protecting the environment.This study focuses on the influences of wet-process operating conditions on REE leaching efficiency. The results indicate that REE leaching efficiency increases with phosphoric acid addition in the initial pulp. At a temperature of 75 °C, a stoichiometric ratio of sulfuric acid (H2 SO4 ) to calcium oxide (CaO) of 1.05 and a weight ratio of liquid to solid of 3.5, REE leaching efficiency reached a relatively high value of 52.82 percent. The trends of REE leaching efficiency were similar to those for phosphoric acid (P2O5 ). Extensive tests on the leaching residue showed that during leaching, about 90 percent of the REEs were released from the phosphate rock but only 52.82 percent ended up in the leaching solution. This phenomenon can be attributed to two factors: (1) the effect of phosphate ions (PO4 3-) in the solution, which caused REE ions to form REE phosphates and be precipitated into the leaching residue, and (2) the influence of large amounts of anions such as sulfate (SO4 2-), dihydrogen phosphate (H2 PO4 -) and hydrogen phosphate (HPO4 2-) anions as well as the polar molecule H3 PO4 , which surrounded the REE cations and formed an ion atmosphere that prevented the PO4 3- from contacting and combining with REE cations. Interaction of these two opposite effects determined the REE distribution between leaching solution and residue."

Jan 1, 2017

By Daniel T. Brian, O&apos

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summary. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented in this paper.

Jan 1, 1969

By Gregory A. Hope, Kym Watling, Matthew I. Jeffrey, Ronald Woods

Surface enhanced Raman Spectroscopy carried out in real time has been applied to identify surface species formed during gold leaching in chloride and thiosulfate media. Chloride ion is adsorbed prior to the gold dissolution potential, but its coverage is significantly diminished at the beginning of leaching. A gold chloride band is again observed when dissolution is rapid, together with bands characteristic of AuC14- ions in solution. With thiosulfate, a thin gold sulfide layer is formed slowly in the potential region where leaching occurs. At higher potentials, thiosulfate is oxidized to sulfur and sulfate, both products being identified by Raman spectroscopy.

Jan 1, 2005

By Christian Maguire

The presence of hydrogen sulphide in sewerage systems leads to severe concrete corrosion. Acid causes breakdown of the concrete matrix, and attacks reinforcement. Older sewer systems under acid attack are often found to be acutely corroded, sometimes after short operational periods. Consequently secondary liners are now almost always used. Polymer concrete is extremely acid resistant and if used in segmental linings can forgo the need for a secondary lining. Combined with fibers and/or GFRP rebar Polymer Concrete can produce a very strong acid resistant lining, saving considerable time in the installation of additional liners. This paper explains the problems and advantages of using Polymer concrete in segmentaly lined wastewater tunnels, addressing areas of design, cost, and programming.

Jan 1, 2008

By D. J. Shields

The goal of public policies is to connect desired ends with practical means toward their achievement. How the desired ends are determined, and whose goals and objectives they incorporate, depends upon the culture and political system of the country in question. With few exceptions, policies change over time to reflect changed perspectives and understanding of the world around us. This is true regardless of the policy area in question. Thus, how societies view and manage their mineral resources has evolved in response to public attitudes, societal needs, economic circumstance, cultural perspectives, political orientations, technological advancements, and geological knowledge. In this paper we examine how the scope of concern has changed for mineral policy. We then review the overarching issues that have in recent years been considered essential components of mineral policies. We point out how neoclassical microeconomics has influenced recent policy design. We then use a market flow diagram to illustrate how policies can be focused at specific market issues. We next discuss mineral resources in the context of sustainable development. We identify issues that become relevant when the frame of reference is enlarged beyond ensuring supply and capturing economic rent. We show that policy based solely on neoclassical economics may not be able to effectively incorporate these issues.

Jan 1, 2007

By H. Polat, B. Mohal, S. Chander

Several nonionic surfactants and one anionic surfactant were tested to enhance the flotation response of a low-rank coal. The nonionic surfactants included an ethoxylated octylphenol and several polypropylene-polyethylene block copolymers, and the anionic surfactant was a dioctyl sulfosuccinate. All of the surfactants improved the yield significantly, but the influence on grade was complex. To elucidate the mechanisms involved, separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents, a correlation between the emulsifying power of the surfactant and the flotation response was observed. An increase in the number of droplets produced was considered to he the main reason for increases in the yield. However, a small amount of surfactant adsorption on coal is essential to promote adhesion of oil droplets. When the surfactant was introduced into the flotation pulp prior to addition of dodecane, the benefits of the surfactant decreased significantly. The decrease was attributed to both a decrease in hydrophobicity of coal through increased surfactant adsorption and a decrease in the surfactant available for emulsification. When a surfactant dispersed in oil was used, the transfer of surfactant to the aqueous phase was minimal, and a considerable increase in yield was observed.

Jan 1, 1995

By Andrew P. Gize

A petrographic approach to studying the organic matter in ore deposits is advantageous in that direct observation of sample heterogeneity can be made, organic constituents (macerals) can be identified, and valuable information about the geological history of the sample (such as thermal history, oxidation, and reworking) can be obtained. Thermally immature bitumens are compositionally and structurally heterogeneous, and optically isotropic. The end product of thermal alteration, graphite, is compositionally and structurally homogeneous, and optically an isotropic. One route by which thermally immature bitumens can approach the graphite structure Is by an aromatic intermediate phase, termed mesophase. The development of optical anisotropy and a thermal mesophase has been observed In several high temperature deposits. Textures in bitumens are described from the thermally-altered Mississippi Valley-Type deposit at Nanisivik (Northwest Territories), the silver-vein deposit at Kongsberg (Norway), and the gold deposit at Carlin (Nevada). Textural evidence for multiple generations of bitumens, supportive of a pulsing model for incoming brines, is shown. Petrological evidence for the introduction of bitumens as an immiscible phase or possibly as micelles is shown in the Carlin and Kongsberg deposits.

Jan 1, 2013

By George M. Potter

Under contractural arrangements with the Bureau of Mines, Mountain States Research and Development, Inc. (MSRD) completed a technological investigation to determine the feasibility of in situ mining of metal commodities other than copper and uranium, The study was based upon available literature and experience. The selection of potential candidates for in situ mining was influenced by economic importance, probable amenability to in situ methods, and environmental considerations. Four metals (or metal pairs) were chosen for feasibility studies: aluminum (with a copper byproduct), gold-silver, and manganese were recommended for further study and action; cobalt-nickel was also recommended contingent upon preliminary laboratory leaching and recovery investigations and field geohydrological work. Mining and recovery plans and an economic evaluation are included. Other metals with potential for in situ leaching are lead/ zinc, molybdenum, and vanadium.

Jan 1, 1981

By Mohammed Sakr

The empirical relationship between torque measured during installation and pile capacity has gained a wide acceptance in the helical pile industry in the last few decades. This paper presents a theoretical model developed to estimate torsional resistance of cohesive soils to helical pile installation. The proposed torsional resistance model was then used to establish torque factor, Kt, a factor that is widely used in the industry. The results of the study indicated that the Kt factor is a function of the load path (i.e. tension or compression), pile geometry and soil properties. The assessed Kt factors in tension and compression were validated by the results of 74 installation records and full-scale helical pile load tests. A parametric study was also performed to qualitatively assess the relative importance of different parameters that affect the Kt factors.

Aug 1, 2013

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By Abdullah Arik

An ore reserve block model is the basis for various decisions in mine development and production. The block model is initially built using the information from the drillhole data only. Once the mine is put in operation, the information from the blasthole data becomes available. Since the spacing of the blastholes are much closer than the exploration drillholes, the blasthole data gathered from the mine over the years become quite extensive containing valuable information about the deposit. In practice, the information from the blastholes is the basis of determining the ore and waste boundaries between and within mining blocks. In an ore reserve model, the valuation of blocks on and close to the pit face can obviously be improved by using blasthole data from neat by drilled and mined-out blocks in addition to using the widely spaced drillhole data. The ideal basis on which to integrate blasthole and drillhole data is to use cokriging.

Jan 1, 1996

The knowledge of aggregate size under various chemical and hydrodynamic conditions is very important for selective agglomeration, flotation and water clarification processes. Traditionally, aggregate size measurements are conducted using an ex-situ technique or in a diluted suspension. In either case, the measurement occurs in an environment that does not resemble the actual conditions under which the aggregates are formed. In this study, an on-line scanning laser microscope has been used to study the coagula size of micronized coal suspensions as a function of pH, solids concentration and agitation intensity. A maximum aggregate size of 310 µ m was obtained under relatively quiescent conditions and at pH values near the iso-electric point (iep) of the coal. The aggregate size results compare well with the coagulation efficiency measurements obtained under the same pH conditions.

Jan 1, 1994

By H. J. Marais, P. C. van Aswegen

The Biological Oxidation (BlOX®) Process for the treatment of refractory gold ores was commercialized in 1988. During the last decade, the technology has developed into a mature, commercially viable process, with five additional operations commissioned, including operations at Sao Bento in Brazil, Harbour Lights and Wiluna in Australia, Ashanti in Ghana and Tamboraque in Peru. With ongoing development, the efficiency and cost effectiveness of the process have both improved, making it an attractive alternative to conventional refractory treatment processes such as roasting and pressure oxidation. The bacterial culture is robust and can withstand the normal fluctuations experienced on an operating plant. The plants are simple to operate, making it ideal for remote areas. The scale-up potential of the process has been proven, and it can be applied to large refractory ore bodies. The process is environmentally friendly. Neutralization of plant effluents produces precipitates that comply with the most stringent environmental regulations.

Jan 1, 2000

By James D. Bennett, David L. Passmore

The Coal Mining Section of the National Safety Council has selected hand and finger injuries of coal miners as a major topic for safety policy analysis [Tinney, 19851. So that facts about hand and finger injuries can be used to guide the Committee's work and the work of policy-makers, we present in this paper detailed analyses of the following factors related to hand and finger injuries received by coal miners between 1975 and 1983: occupations of the injured miners; activities of the miners when injured; machines involved; objects, substances, exposures, or bodily motions that produced or inflicted the injuries; principal physical characteristics of injuries; and events directly resulting in the injuries. We analyze hand injuries for underground and surface mines separately because of the remarkably different production methods and hazards evident in these two operating environments. We do not, however, provide information about hand and finger injuries that occurred in surface operations at underground sites (such as yards, shops, or tipples), auger mining operations, culm banks, dredging operations, mill or preparation plants, offices, or laboratories. The most comprehensive information about the safety of coal mining in the United States is assembled by the Health and Safety Analysis Center (HSAC) of the Mine Safety and Health Administration of the United States Department of Labor. Mine operators in the United States report to HSAC all injuries as required under Part 50, Title 30, of the Code of Federal Regulations (mandated by Section 103 the Federal Mine Safety and Health Amendments Act of 1977, Public Law 95-164). These regulations stipulate that injuries must be reported within ten days of their occurrence on a United States government data collection form, Mine Accident, Illness and Injury Report (MSHA Form 7000-1). HSAC maintains these data primarily to produce federally-mandated reports. HSAC resolves injury reports that are incomplete, checks for errors in data coding and handling, and corrects inconsistencies in data submitted by

Jan 1, 1986

By Qing-Wang Hao

In this paper, the authors attempt to develop engineering based approaches for estimating safety factors against pillar and floor failures and predicting likelihood of subsidence events over abandoned coal mines in Illinois. There are two critical problems involved in the analysis: determination of geotechnical properties, and consideration of time effect. The authors attempt to solve the problems by generating hypotheses, which are used to modify existing engineering models for estimating pillar and floor safety factors. The modified models are validated using data from two well established databases of subsidence events over active and abandoned mines in Illinois. The data analysis suggests that most of the trough type subsidence events in Illinois were caused by floor failures rather than pillar failures. The subsidence incubation period seems to be directly related to initial floor safety factors at the time of mining. This correlation can be used to predict the likelihood of subsidence and to assess subsidence risks within both spatial and temporal contexts where detailed mine maps are available.

Jan 1, 1986

By R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic solutions, over the pH range 1-7, to determine a potential range for co-dissolution.. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated predominance diagrams for the copper-arsenic-sulfur system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Feb 23, 2014

By Matthew Preedy, Anthony Pooley, Mike Wongkaew, Dirk Bakker, Raghu Bhargava

Sound Transit’s ST3 program will add 62 miles of light rail to the Puget Sound area, including connections to the neighborhoods of West Seattle and Ballard. These connections include considerations for both elevated and tunnel alternatives in West Seattle and Ballard, as well as a new tunnel and six underground stations in the densely developed downtown Seattle. This paper describes the conditions and constraints along the corridor, and the latest development in the ongoing process to plan the underground guideways and stations.

Jun 13, 2023

By E. Fahrenkrog, D. Sbartaro, E. N. Cifuentes

An intelligent supervisor using expert system tools and applied to a crushing plant has been developed with a structure based on a model of a human operator. It consists of a knowledge base containing a qualitative model of the process and a rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of system to supervise the automatic operation of a plant. There has been very significant development in artificial intelligence over the last two decades. Within this development, two approaches can be distinguished, (Winston, 1984). The "model approach," in which the main objective is to understand and model the be¬havior of living systems. The second approach is the "engineering approach." Here, systems capable of performing tasks usually requiring human intelligence are created. As part of this latter approach, knowledge engineering and its main achievement, expert systems, have been developed. Expert systems arose from the need to incorporate the abilities of a human expert in solving realistic problems in which the conventional approach has great difficulties. The first successful applications of expert systems were in medical diagnosis, geophysics, and fault detection. However, since 1971, when Fu (1971; defined intelligent control as the inter action of artificial intelligence and automatic control, some significant developments in the use of artificial intelligence tools for process control have been achieved (Astrom, 1986; Pinto 1988; Fahrenkrog, 1988; and Porter 1987). The modern control theory has made important advances. And, although successful in some applications, it has failed to cope with the practicalities of many industrial processes. As a result, the automatic operation of a plant has been confined to a small region around a normal operating point and to periods without any great disturbance. One of the main reasons for this is the lack of accurate and structured knowledge of the processes involved. Despite this, operators applying their knowledge, experience, and a little intuition, often obtain good results controlling the plant in such situations. Considering the above, the next obvious step is to include similar reasoning capacities in a computational system. The development of such an expert supervisory system prototype applied to a mineral crushing plant is presented. Problem description The problem is to conceive a control system with the ability to handle quali-

Jan 1, 1989

By Felicia F. Peng

In operation of column flotation of fine coal, the smaller bubbles are required to effectively recovery of fine hydrophobic particles. However, smaller size bubbles alone does not ensure an efficient flotation for fine particles. The sufficient available bubble surface area per unit column are essential for effective column flotation. The experiments are conducted in a lab-scale column using two different bubble size distributions and three different particle size distributions for flotation of Pittsburgh No.8 seam coal. The interaction between particle size, aeration rate, feed rate and wash water addition are examined in this investigation to establish the optimal operation conditions for flotation of fine coal. Despite of wide range of operation conditions used in this study, it is found that the experimental data fall in a single characteristic recovery-ash curve for a given bubble size distribution and particle size distribution. The major parameters affect the flotation performance points along -the characteristic recovery-ash curves are aeration rate/frother dosage, feed rate and wash water rate-.

Jan 1, 1994