Search Documents

By Takayuki Sakai, Takefumi Takuma, Lee Roesner

"70-foot deep rectangular-shaped bulkheads were built with sheet piles as launching and receiving shafts for a pipe jacking operation for new underground waterlines in a densely populated section of Los Angeles, California. The Press-in Piling Method was specified to drive 95-foot long sheets (a record for the method) to form the bulkheads for the Los Angeles Department of Water and Power’s LA-29 (DWP) Connection Modification and Pipe Jacking. The piling was chosen because of its very low noise and practically vibration-free nature since the site is surrounded by houses, an apartment complex, and existing water lines. The out front areas of the bulkheads were grouted to let the TBM go through without major ground water leaks. Hydrophilic foam grout was also injected in addition to welding steel scab plates on the inside to seal them to achieve sufficient watertightness behind a few split interlocks. BACKGROUND This project was located in the Crescent Heights area of Los Angeles which is a few miles south of Beverly Hills. The project represents the completion of the last phase of the Stone Hollywood Trunk Line. This was an 8-mile long water trunk line that averaged 60 inches in diameter and was built to improve the reliability of the DWP’s major water system. This section of the project involved driving 2 deep shafts to allow for the installation of a 350-foot-long 72-inch steel casing using microtunneling construction. See Figure 1 for the shaft locations and the tunnel alignment. The challenge for the project was that this water line would have to pass beneath the Hollyhills buried box drain (15 feet high by 20 feet wide). Further complicating the construction was the soils beneath the drain. The DWP chose to drive the tunnel at a depth of approximately 65 feet to ensure that the ground conditions were uniform and suitable for the microtunneling equipment. There were two previous attempts to construct this work which failed because of poor ground conditions and very high water levels. This third attempt was critical because the DWP could not afford to have another failure due to the fallout with the residents being impacted by the project."

Jan 1, 2016

By R. Marrill

Mining is a complex and intensive industry. Extracting raw material with different shapes, sizes, chemistry from the earth?s crust and transform them into a standardized and high quality final product is a big processing challenge - which involves energy and control on large scales. Not only is the physical work challenging, the mining industry today is facing unprecedented challenges: Decline of mineral grade and reserves, cost escalation for new developments and modernization, regulations, safety, lack of skilled people, and market uncertainty are the new constant. It is clear that process control and management of electrical power will be of increasing importance to the recovery rates the mine will achieve. The objective of this paper is to provide a quick vision about future trends and evolutions in technology related to these fields and their impact on Electrical Safety and Control of the mineral recovery. The paper will cover trends in safety, energy management and efficiency, communications of data, control room evolutions, plant integration, other control technologies, and we will examine how these technologies provide information and the benefits of aligned reporting systems to address current industry challenges. More than just the trends or breakthrough concepts, current technologies are available today that can be applied in the mineral recovery operations now to help overcome anticipated future challenges will be presented later in this document. Finally, a brief discussion to look at some real tools to help make real time changes to the process while maximizing recovery and optimizing cost.

Feb 27, 2013

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987

By S. E. Restrepo

In recent years, mining operations have experienced the impacts of climate variability, increasing costs, and changes in the socioenvironmental dynamics of the territories. For this reason, the aggregates industry needs to design and define concrete and immediate actions to address climate change. An appropriate way to achieve this is as follows: • Calculate greenhouse gas emissions, sources, and relevance factor. • Make projections of future scenarios. • Design and implement action plans The proposed climate change mitigation and adaptation projects are logistical optimizations of mining equipment (mitigation). Second is the design of an early warning system to predict possible flooding (adaptation).

Mar 2, 2022

By Robert M. Anderson

A popular perception by the public and many mining claimants, is that the 1872 Mining Law provides a statutory right to mine and extract minerals from the public lands. This perception in reality, is both true and false, depending on the mining claimants' ability to meet federal and state environmental, cultural and endangered species laws. Land use decisions and proposed legislation affect exploration and development opportunities in California. It is imperative that the mining industry involve itself in the planning process to ensure that BLM decision makers are fully informed of industry's knowledge and concerns. STATUTORY RIGHTS AND ENVIRONMENTAL CONSTRAINTS "No other problem has such a sense of urgency and poses as profound consequences to the quality of life and the creation and distribution of societal wealth as how we protect the environment. Certainly, the environment is the single biggest issue facing mining and mineral activities in the new decade. David S. Brown The 1872 Mining Law was passed, ironically, the same year the nation's first National Park was established. It is a perception that the establishment of Yellowstone National Park was the beginning of the United States' earliest environmental movement; brought on, perhaps, by the rapid clearing of land for homesteading purposes and, the concern that many acres of the public domain were being disposed of through a multitude of public land laws. While there was an effort being made to designate some special and unique public lands as parks for preservation purposes, environmental concern and awareness did not lead to mandatory identification of environmental impacts and appropriate mitigation until the passage of the National Environmental Policy Act in 1970. Consequently, it is not surprising that the original United States Mining Laws of 1866, 1870 and 1872 had no mention of environmental protection. There have been numerous attempts to repeal the 1872 Mining Law over the last 50 years for a variety of reasons. Currently, there is a perception by the general public, media and even some in congress, the mining industry and BLM that a change is needed. The environmental organizations want the industry to be more accountable for reclamation and post mining uses. In Tn nEnvironmental Agenda for the Future," leaders of America's foremost environmental organizations state that the mining law "includes no protection for the environment," and therefore, should be reformed. We can all acknowledge, as stated above, that the mining law, per se, requires no "protection. However, the Bureau of Land Management (BLM) clearly has the authority and the responsibility to fully "protect" non-mineral resources while providing for the extraction and processing of mineral resources by private industry. There are about 13 major federal laws that have indirectly or directly amended the mining laws to require Environmental, Historic and Cultural Protection." There have been many mining law case decisions about the statutory and constitutional rights of miners to explore open federal lands, "stake a claimg" and extract minerals. What needs to be fully understood is how federal laws, as enumerated on Table 1, may affect these rights. What follows is a description of

Jan 1, 1991

By Nicolae Dobritoiu

From experience and scientific references it is known that during information processing, the following error types are transmitted: technical, analogy errors and method errors. For decreasing the value of these errors, especially of the method ones, old algorithms should be perfected and new ones should be developed for processing, interpreting and achieving the graphical layout by means of automatic data processing. In this respect, we propose a new deposit model based on numeric mathematical modelling which requires the use of automatic data processing. The utilization of the numeric model of the proposed deposit, allows the obtaining of the following advantages: • the model is used for any deposit form; • it is used for the calculation of deposit resources (volume, weight, and content); • it is used in design due to the facility of obtaining sections through the deposits area; • it eliminates at "0" the errors of graphical data transcription; • the use of the model imposes a uniform geological research; • the algorithm is transposed in a package of programs.

Jan 1, 2002

By George A. Desborough, Stephen J. Sutley, Reinhard W. Leinz, Paul H. Briggs

The mode of occurrence of metals in mine wastes is investigated using sequential extractions. Metals are extracted from some or all of seven operationally-defined phases: water-soluble, ion-exchangeable, carbonate, amorphous Fe-oxide, crystalline Fe-oxide, sulfide, and silicate. The quantity of metals extracted from each phase varies with particle size. The presence of jarosite (potassium end-member formula, KFe3[SO4]2[OH]6) influences the selection of the procedure for extracting the crystalline Fe-oxide phase. Anglesite (PbSO4) and cerussite (PbCO3) are extracted as several phases. Extraction results can be explained only in part by X-ray diffraction (XRD) mineralogy because of lack of specificity of the extraction procedures, relatively high XRD detection limits, and the presence of 40% XRD-amorphous matter in each waste. The increasing chemical strength of the sequentially applied methods provides a basis for judging metal availability, water-soluble metals being most available and silicate-bound metals being least available.

Jan 1, 2000

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population.

Jan 1, 1984

By P. Jacquin

Many a deposit estimation has been carried out since geostatistical methods were first implemented. To date however few mining programs have totally been completed and even fewer comparisons can be drawn between estimated reserves and extracted ore tonnages. Aluminium Pechiney work a number of bauxite mines in Southern France. As from 1969 they modified their deposit estimation methods, giving up traditional approaches and opting for geostatistics. At that time, the authors of this paper were entrusted with the first geostatistical estimations and in particular, those concerning the deposits mentioned herein. Over the past decade a number of deposits have been worked out and we thought it interesting to report about comparative results. French bauxite deposits are of the karstic, as opposed to the lateritic, type. The bauxite, formed at some distance of the present-day deposit, was brought to and trapped in limestone karst pits. Subsequent physical and chemical alterations may have taken place : silica and carbonate drifts, recent karst slips. The morphology of these deposits is often rather complicated. The deposits are small from a few hundred thousand to a few million tons at the most. The overburden thickness usually precludes open mining. Mining investments and financial risks are often high, making it necessary to obtain optimal information on the deposit considered for mining. For the three cases brought up in this paper, deposit sizes, exploration methods and conclusions differ. They are brought up mainly to show the advantages inherent to a quality geostatistical study and the lessons drawn by Aluminium Pechiney.

Jan 1, 1982

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and nonfatal injuries that occur in mining in the United States. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the U.S. Mine Safety and Health Administration (MSHA) from 2010 through 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84 percent involved the workers not using fall protection, fall protection not being provided or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment or working near highwalls. In most cases, a single, basic, corrective action — such as using fall protection — would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By Jin Zhao, Weijie Wei, Jinwang Zhang, Xiaohang Wan, Shengli Yang

Reasonable mining-retention ratio (ratio of room width to pillar width) is vital to recovery rate and stope stability in underground mining of solid potassium salt deposits. Based on the engineering background of a solid underground potassium salt mine in Khammouan Province, characteristics of the plastic zone of the pillar, and the variation of recovery rate and stope stability under different mining-retention ratio conditions are discussed. The results show that compared with current room width (8 m) and pillar width (10 m), the optimization method of improvement of stope stability. The research results are helpful to recover as much solid potash resources as possible under the premise of ensuring the stability of stope.

Jun 25, 2024

By A. T. Yu

A recent analysis completed by the United States Department of Commerce predicts that the 1968 Gross National Product will reach a record high of 864 billion dollars. As our nation annually increases its total output of goods and services, as has been the trend, the consumption of steel and its most basic raw material - iron ore - also must increase, To deliver the most economical unit of iron ore to the blast furnace, each segment of the transportation system must be co-ordinated and utilized to its highest degree of efficiency. In some cases, such as with the water segment of the system, a new investment in capacity will be required.

Jan 1, 1968

By X. Zhu

Establishment and monitoring of revegetation in areas affected by mining activities is quite often a difficult task. The efficiency of the scheme applied can be substantially improved by using simple adequate indicators so that progress and trends can be plotted, elucidated and assessed over time. Sustainable revegetation management indicators should take into account soil quality and area characteristics, as well as social, economic and political aspects. In the present paper an interactive prototype Spatial Decision Support System (SDSS) is presented. The system, based on methodological studies, has been designed to identify and interpret indicators that can be used for the evaluation of revegetation efficiency. It provides a platform for formulating indicators describing biophysical, socio-cultural and economic processes during the entire revegetation period. It integrates modular assessment, database management sub-systems and Geographical Information System (GIS). It is structured in a way that takes into account the project environment, soil quality, land characteristics, data acquisition control, output engines and spatial analysis. The output generates visual quality diagrams and interactive attribute quality maps that elucidate revegetation issues.

Jan 1, 2007

By Jan Walaszczyk

The paper concerns the calculation of stresses and displacements in working area of room-and-pillar mining system of cooper ore mines. A three-dimensional rock mass model based on the finite element method has been developed. The complete strain-stress characteristic for pillars has been applied, but for the purpose of modeling the curve has been approximated by three segments of lines: - the first represents a behavior of pillar before a failure, -the second corresponds to a progressive pillar failure phase, - the third represents the part of the curve, where the increase of strains do not cause the stress changes, and it is called the residual strength. The criterion of model stability has been derived, which can be useful for predicting rockmass stability. The programs have been built, which allow to calculate stresses in bar elements, displacements in plate nodes, and estimate the stability of the model, which consists of plate elements and one-dimensional elements with a segment strain-stress characteristic. The programs were used to consider two different problems, which are connected with mining design and the exploitation systems.

Jan 1, 1992

By Rimas Pakalnis, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

Jan 1, 2005

By C. J. Bise

Safety training requirements differ from mine to mine due to changes in the demographic characteristics of the workers or changes in job and organizational characteristics. Accordingly, a microcomputer-based procedure has been developed to assist mine trainers is determining if undesired worksite performances result from lack of knowledge or skill, which are trainable categories, or from categories that are considered to be non-trainable (such as equipment limitations or management procedures). A special effort was made to understand the psychology of worker behavior by analyzing worker reactions to various organizational and job characteristics.

Jan 1, 1995

By G. E. Rouse

Anomalies of sulfur dioxide and other gases have been defined, by direct measurement, around various sulfide bodies. These readings were made (1) in soil gas and (2) in the atmosphere, from both ground vehicles and, to a limited extent, from helicopters. Test areas included porphyry copper and molybdenum deposits, sulfide bearing vein systems, pyrite zones associated with sandstone uranium accumulations, and pyrite-bearing mine dumps. Some of the deposits are covered by as much as several hundred feet of overburden or barren rock, while others outcrop, or have been exposed by mining operations. Depending on local conditions, background values of sulfur dioxide in soil gas and the atmosphere range from 1 to 15 parts per billion. Using present techniques, anomalous readings are recognized at approximately two times background. Apparent "depth penetration? on known deposits has ranged to several hundred feet. Readings have been made over known deposits from a helicopter and ground vehicle moving at up to 40 mph. The rate at which the survey may be carried out depends largely on the size and extent of the anomaly. The existence and magnitude of sulfur dioxide anomalies around sulfide-bearing deposits is a function of geology, target size, soil moisture, and climatic conditions such as temperature and temperature changes, barometric pressure, wind velocity, and precipitation. Industrial S02 pollution can effectively mask the presence of the anomalies sought.

Jan 1, 1971

By P. Oghazi

It is possible to have traceability in the mining industry, by parameters and signatures like particle mineralogy, mineral association, texture and mineral liberation. The study is on an apatite-iron ore deposit at Malmberget, Sweden, and characterizes an ore body both mineralogically and texturally in a quantitative manner by using analytical methods like optical microscopy, microprobe (EMPA) and an automatic SEM based system, Particle Texture Analysis (PTA). The mineralogy was evaluated by PTA and characterized by modal mineralogy, mineral liberation and mineral associations. Magnetite has a simple outline and straight grain boundaries and the gangue minerals have a finer particle size with a more complicated texture. The PTA analysis also shows that apatite is associated to magnetite as mixed particles, while smaller grains of magnetite are inclusions in feldspar. Result from particle texture analysis shows that there is a connection which link to the mine-to-mill context, and it may be used to create traceability. This link is not the associations of the main ore mineral magnetite, nor the modal mineralogy. Instead, it is the mineral associations of contaminating minerals (apatite and feldspar) that appear to be most promising since they survive from mine to mill. The modal mineralogy may be used to understand how contaminated minerals break into or out of particles size fraction during grinding.

Jan 1, 2010

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By P. W. Finck

Detailed mapping, using a large diameter diamond-drill in conjunction with high resolution reflection seismics, has increased known resources of kaolin clay and glass-grade silica sand from scattered deposits generally < 1 km2 to large areas of Cretaceous valley fill up to 130 m thick. Detailed chemical and physical analysis of drill core is presently underway. Silica sand deposits intersected in this study are up to 99.4 % SiO2 without beneficiation. Light grey to white kaolin clays identified by XRD and DT A have concentrations values (without beneficiation) up to 47.28% SiO2, 37.44% Al2O3, 0.45% Fe2O3, 0.49% K2O, 0.07% Nap, 0.07% CaO and 0.39% MgO.

Jan 1, 1996