Search Documents

By Nigel Pearson, Malcolm J. McPherson

In the Grasberg Mine, a series of orepasses of diameter 2 to 4m are being constructed, each one to carry as much as 10,000 tlhour of copper- and gold-bearing ore through single stage vertical drops of over 500m. At the base of each orepass, the fragmented rock falls into an orebin of diameter 1 Om and 100m deep. Long before the planned tonnages were reached on the early orepasses, a problem arose that was both serious and intriguing. Pressurization of air in the orebins caused by the falling rock reached such levels that when the feed to the top of an orpass was interrupted, a massive surge of air ascended rapidly and produced a dangerous backblast accompanied by dust; grit and rock fragments from the top of the orepass. Backblasts lasted for about one minute and were not only hazardous to the health and safety of personnel but also required time-consuming clean-up operations. The paper describes the aerodynamic analyses that were con- ducted in order to understand fully the mechanisms involved in the phenomenum, and the development of a procedure that al- lows the effects of falling material to be incorporated into existing ventilation network software.

Jan 1, 1997

By K. S. Whiting

Elevated concentrations of copper, cobalt, and arsenic within the Panther Creek Basin sediments in north central Idaho prompted an evaluation of the sources of the metals. Potential tailings and waste rock source samples collected at the head of Blackbird Creek were compared to sediment samples in the Panther Creek Basin using electron microprobe techniques. The mineral types, degree of alteration, and the morphology of the metal-bearing sediment grains within Blackbird and Panther Creeks were found to consist of copper-, cobalt-, and arsenic-bearing sulfide minerals.

Jan 1, 1997

By N. Ripepi

"The Langmuir model has been widely used for the coal-methane sorption process via an isothermal test. However, even though the temperature-dependent Langmuir model were recognized theoretically and experimentally, the quantitative relationship between the Langmuir’s constants (a & b) and temperature have not been clarified and confirmed by lab test data. This paper collects 158 methane-coal sorption data under different temperatures, which apply the Langmuir model to consider the relationship between Langmuir’s constants (a & b) and temperature (see APPENDIX I). Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters (a & b). The results from these published isothermal tests confirm that 1) there is no consistent relationship between Langmuir’s constant-a and temperature; 2) the Langmuir model is a temperature-dependent model, and the temperature-dependent feature is mainly shown by the relationship between Langmuir’s constant-b and temperature; 3) The relationship between Langmuir’s constant-b and temperature can be described by both the exponential and linear relationship with dried coal. This paper provides a database for temperature-dependent Langmuir’s model, which can be used for reservoir simulation of coalbed methane reservoir, coal seam degasification modeling for underground coal mines considering the heating effect induced by geotherm and heat injection (via hot water, hot steam, ultrasonic, etc.). INTRODUCTION The isothermal test for gas sorption on coal is one of the fundamental tests in Coalbed Methane (CBM) recovery fields, such as underground coal mine methane degasification, CBM gas-in-place estimation, and carbon dioxide sequestration in un-minable coal seams. Generally, two methods, volumetric and gravimetric, are employed to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012). Based on these two approaches, a series of commercial and self-assembled instruments are built and several calculation methods are used to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012, Gasparik, K., 2014; Goodman, A. L., et al, 2004; Zhang, L., et al, 2013). In the post-processing stage, many models are provided to analyze isothermal data in order to understand the storage mechanism of gas in coal. Common models include the Langmuir model (and its extended forms), the pore-filling model, multilayer adsorption model (BET), and the Gibbs’ model. Among these models, the Langmuir model is the most widely used for its simplicity and functionality. The Langmuir model is expressed as follows:"

Jan 1, 2016

By Rudolf E. Pfister

One of the Swiss transalpine highways includes two remarkable tunnels: the 16.3 km long Gotthard Road Tunnel and the 9.3 km long twin tube Seelisberg Tunnel, both presently under construction. Large diameter shafts up to 900 m long are required for ventilation. Excavation techniques for rock formations ranging from loose sedimentary rock to granite and very hard siliceous limestone were carefully evaluated. The methods finally applied include excavation of shafts in hard rock, conventional drilling and blasting, excavation by ripper-tooth excavator ("Big John") in marlstone, shield protected heading in loose material and soft rock, and tunnel and shaft lining, both by poured concrete and by prefabricated elements. A critical review of the success of these methods can now be made after a five year construction period.

Jan 1, 1976

By H. Polat, S. Chander

Relatively large amounts of hydrocarbons such as fuel oils are often needed in the flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promoters. The reagents that are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Because the physical and chemical variables influence various subprocesses in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of the clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promoters. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1999

By T. Cohen

Technological innovation in the minerals industry must be driven by the need to improve performance according to social, as well as environmental, safety, efficiency and production criteria. This paper outlines the possibilities and rationale for incorporating constructive technology assessment into technology research and development within the CSIRO Minerals Down Under National Research Flagship (MDU). The paper develops a process of Social License in Design that attempts to address the future social challenges and opportunities of a technology during development by utilising forecasting techniques and accounting for the perspectives and values of decision makers and likely stakeholders. Interviews with senior technologists and social scientists within MDU reveal the institutional context into which the Social License in Design process is to be situated and highlight key factors that may inhibit or enhance its uptake.

Jan 1, 2011

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By L. A. Bakhvalov

According to the practice of mining management in the system of industrial complexes, the Kazakhstan gold mines are part of the mine processing industrial concerns providing ore-mining and ore-dressing. The cycle technology of winning operations used at the mining of vein deposits in the mines of the industrial concern is mainly provided by the systems of scrapping, scipping and electric locomotion. At present the information and computer system, elaborated on the basis of the Maikain underground mine is intended for creation of the system of automatic operation for the industrial complex mines. The information and computer system includes: - parametres characterising the accepted technology of works; - the main parametres characterising the technical devices of operation and control ; - information about the material, technical and personnel resources available at the mine; - mining and geological conditions of the deposit; - the facilities of the subsidiary units, of the mine; - the direct parametres and technico-economical indices in which the mine efficacy and activity is estimated. The suggested structure of the automatic operation system can be sensibly realized with the application of the microprocessor on the first level, the personal computer IBM PC/XT or PC/AT on the second level. For the complete realization of the project each mine will need 4-5 computers (as PC/XT), one IBM PC/AT and each mine complex - one super IBM for creation of the distributed information bank and its including in the integral world communication system.

Jan 1, 1992

By J. Kircher

Nevada Goldfields' Aurora Mine consists of a 270 mtpd (300 tpd) precious metals mining and milling facility located 28 miles southwest of Hawthorne, Mineral County, Nevada and lies within five kilometers of the Nevada-California border. (Figure 1) Ore production presently is derived 85% from an open pit source with the balance from underground. The Aurora Mill is a compact conventional cyanide plant utilizing a carbon-in-leach extraction process followed by stripping of loaded carbon and electrowinning at Nevada Goldfields Kingston Mine, located near Austin, Nevada. Production commenced in December 1987 and annual gold production is currently 20,000 troy ounces of gold and 22,000 troy ounces of silver per annum, produced at an average cash cost of $178 per ounce of gold. Tailings handling at, Aurora was originally accomplished using a belt filter press producing a solid cake that was then transported to a final storage area. Although overall operating costs at the mine were' in the lower percentile of producing gold mines, the tailings handling portion of the operating costs were inordinately high.

Jan 1, 1989

By Bernd Hagenah, Hans-Peter Vetsch, Eric Jones, Sean Cassady, Danielle Johnson, Petr Pospisil

There are a number of issues associated with freight trains in non-electrified tunnels that are fundamental during the planning and operation of a rail tunnel. During uphill operation, increased air temperatures at the air intake locations of diesel trains can reduce diesel motor efficiency (stalling/choking) and affect HVAC systems. Strong airflows can aggravate fire scenarios due to fanning or water-reactive cargo materials. This paper focuses on the impact of freight trains on tunnel safety concepts, strategies to overcome heat issues at locomotive air inlets and air quality in tunnels operating diesel trains.

Dec 1, 2022

By S. A. Diatchkov

There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices .

Jan 1, 1995

By R. E. Hucko

The goal of the U.S. Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high- quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories.

Jan 1, 1986

By Takayuki Sakai, Takefumi Takuma, Lee Roesner

"70-foot deep rectangular-shaped bulkheads were built with sheet piles as launching and receiving shafts for a pipe jacking operation for new underground waterlines in a densely populated section of Los Angeles, California. The Press-in Piling Method was specified to drive 95-foot long sheets (a record for the method) to form the bulkheads for the Los Angeles Department of Water and Power’s LA-29 (DWP) Connection Modification and Pipe Jacking. The piling was chosen because of its very low noise and practically vibration-free nature since the site is surrounded by houses, an apartment complex, and existing water lines. The out front areas of the bulkheads were grouted to let the TBM go through without major ground water leaks. Hydrophilic foam grout was also injected in addition to welding steel scab plates on the inside to seal them to achieve sufficient watertightness behind a few split interlocks. BACKGROUND This project was located in the Crescent Heights area of Los Angeles which is a few miles south of Beverly Hills. The project represents the completion of the last phase of the Stone Hollywood Trunk Line. This was an 8-mile long water trunk line that averaged 60 inches in diameter and was built to improve the reliability of the DWP’s major water system. This section of the project involved driving 2 deep shafts to allow for the installation of a 350-foot-long 72-inch steel casing using microtunneling construction. See Figure 1 for the shaft locations and the tunnel alignment. The challenge for the project was that this water line would have to pass beneath the Hollyhills buried box drain (15 feet high by 20 feet wide). Further complicating the construction was the soils beneath the drain. The DWP chose to drive the tunnel at a depth of approximately 65 feet to ensure that the ground conditions were uniform and suitable for the microtunneling equipment. There were two previous attempts to construct this work which failed because of poor ground conditions and very high water levels. This third attempt was critical because the DWP could not afford to have another failure due to the fallout with the residents being impacted by the project."

Jan 1, 2016

By R. Marrill

Mining is a complex and intensive industry. Extracting raw material with different shapes, sizes, chemistry from the earth?s crust and transform them into a standardized and high quality final product is a big processing challenge - which involves energy and control on large scales. Not only is the physical work challenging, the mining industry today is facing unprecedented challenges: Decline of mineral grade and reserves, cost escalation for new developments and modernization, regulations, safety, lack of skilled people, and market uncertainty are the new constant. It is clear that process control and management of electrical power will be of increasing importance to the recovery rates the mine will achieve. The objective of this paper is to provide a quick vision about future trends and evolutions in technology related to these fields and their impact on Electrical Safety and Control of the mineral recovery. The paper will cover trends in safety, energy management and efficiency, communications of data, control room evolutions, plant integration, other control technologies, and we will examine how these technologies provide information and the benefits of aligned reporting systems to address current industry challenges. More than just the trends or breakthrough concepts, current technologies are available today that can be applied in the mineral recovery operations now to help overcome anticipated future challenges will be presented later in this document. Finally, a brief discussion to look at some real tools to help make real time changes to the process while maximizing recovery and optimizing cost.

Feb 27, 2013

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987

By S. E. Restrepo

In recent years, mining operations have experienced the impacts of climate variability, increasing costs, and changes in the socioenvironmental dynamics of the territories. For this reason, the aggregates industry needs to design and define concrete and immediate actions to address climate change. An appropriate way to achieve this is as follows: • Calculate greenhouse gas emissions, sources, and relevance factor. • Make projections of future scenarios. • Design and implement action plans The proposed climate change mitigation and adaptation projects are logistical optimizations of mining equipment (mitigation). Second is the design of an early warning system to predict possible flooding (adaptation).

Mar 2, 2022

By Robert M. Anderson

A popular perception by the public and many mining claimants, is that the 1872 Mining Law provides a statutory right to mine and extract minerals from the public lands. This perception in reality, is both true and false, depending on the mining claimants' ability to meet federal and state environmental, cultural and endangered species laws. Land use decisions and proposed legislation affect exploration and development opportunities in California. It is imperative that the mining industry involve itself in the planning process to ensure that BLM decision makers are fully informed of industry's knowledge and concerns. STATUTORY RIGHTS AND ENVIRONMENTAL CONSTRAINTS "No other problem has such a sense of urgency and poses as profound consequences to the quality of life and the creation and distribution of societal wealth as how we protect the environment. Certainly, the environment is the single biggest issue facing mining and mineral activities in the new decade. David S. Brown The 1872 Mining Law was passed, ironically, the same year the nation's first National Park was established. It is a perception that the establishment of Yellowstone National Park was the beginning of the United States' earliest environmental movement; brought on, perhaps, by the rapid clearing of land for homesteading purposes and, the concern that many acres of the public domain were being disposed of through a multitude of public land laws. While there was an effort being made to designate some special and unique public lands as parks for preservation purposes, environmental concern and awareness did not lead to mandatory identification of environmental impacts and appropriate mitigation until the passage of the National Environmental Policy Act in 1970. Consequently, it is not surprising that the original United States Mining Laws of 1866, 1870 and 1872 had no mention of environmental protection. There have been numerous attempts to repeal the 1872 Mining Law over the last 50 years for a variety of reasons. Currently, there is a perception by the general public, media and even some in congress, the mining industry and BLM that a change is needed. The environmental organizations want the industry to be more accountable for reclamation and post mining uses. In Tn nEnvironmental Agenda for the Future," leaders of America's foremost environmental organizations state that the mining law "includes no protection for the environment," and therefore, should be reformed. We can all acknowledge, as stated above, that the mining law, per se, requires no "protection. However, the Bureau of Land Management (BLM) clearly has the authority and the responsibility to fully "protect" non-mineral resources while providing for the extraction and processing of mineral resources by private industry. There are about 13 major federal laws that have indirectly or directly amended the mining laws to require Environmental, Historic and Cultural Protection." There have been many mining law case decisions about the statutory and constitutional rights of miners to explore open federal lands, "stake a claimg" and extract minerals. What needs to be fully understood is how federal laws, as enumerated on Table 1, may affect these rights. What follows is a description of

Jan 1, 1991

By Nicolae Dobritoiu

From experience and scientific references it is known that during information processing, the following error types are transmitted: technical, analogy errors and method errors. For decreasing the value of these errors, especially of the method ones, old algorithms should be perfected and new ones should be developed for processing, interpreting and achieving the graphical layout by means of automatic data processing. In this respect, we propose a new deposit model based on numeric mathematical modelling which requires the use of automatic data processing. The utilization of the numeric model of the proposed deposit, allows the obtaining of the following advantages: • the model is used for any deposit form; • it is used for the calculation of deposit resources (volume, weight, and content); • it is used in design due to the facility of obtaining sections through the deposits area; • it eliminates at "0" the errors of graphical data transcription; • the use of the model imposes a uniform geological research; • the algorithm is transposed in a package of programs.

Jan 1, 2002

By George A. Desborough, Stephen J. Sutley, Reinhard W. Leinz, Paul H. Briggs

The mode of occurrence of metals in mine wastes is investigated using sequential extractions. Metals are extracted from some or all of seven operationally-defined phases: water-soluble, ion-exchangeable, carbonate, amorphous Fe-oxide, crystalline Fe-oxide, sulfide, and silicate. The quantity of metals extracted from each phase varies with particle size. The presence of jarosite (potassium end-member formula, KFe3[SO4]2[OH]6) influences the selection of the procedure for extracting the crystalline Fe-oxide phase. Anglesite (PbSO4) and cerussite (PbCO3) are extracted as several phases. Extraction results can be explained only in part by X-ray diffraction (XRD) mineralogy because of lack of specificity of the extraction procedures, relatively high XRD detection limits, and the presence of 40% XRD-amorphous matter in each waste. The increasing chemical strength of the sequentially applied methods provides a basis for judging metal availability, water-soluble metals being most available and silicate-bound metals being least available.

Jan 1, 2000

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population.

Jan 1, 1984