Search Documents

By M. D. Attfield

During 1992 a number of papers were published on aspects of respiratory disease in US underground coal miners. These included reports on trends in prevalence of coal workers' pneumoconiosis, the risks of developing coal workers' pneumoconiosis in relation to dust exposure, and the relationship between lung disease other than pneumoconiosis and dust exposure. The intent of this paper is to provide a summary of the essential findings from these investigations. PREVALENCE AND INCIDENCE OF COAL WORKERS' PNEUMOCONIOSIS Coal workers' pneumoconiosis (CWP) is usually detected in living miners through use of the chest x-ray. Deposits of dust in the lung, and the fibrotic tissue reactions to the dust, are manifested on the x-ray as small and large opacities. These abnormalities are quantified into degrees of severity using a standardized classification scheme (the International Classification of Radiographs of the Pneumoconioses of the International Labour Office). For small opacities, the scheme provides for a four-point scale of abnormality (0, 1, 2, 3), reflecting increasing profusion of the opacities on the x-ray. In this report, category 1 or greater small rounded opacities (CWP 1+) represents the earlier radiographic stages of pneumoconiosis. Large opacities, indicate the later and often disabling stage of pneumoconiosis, usually referred to as progressive massive fibrosis (PMF). Information collected in a national surveillance program for underground coal miners (the Coalworkers' X-ray Surveillance Program (CWXSP)) and a large epidemiologic study (National Study of Coalworkers' Pneumoconiosis (NSCWP)) provide a means to assess trends in CWP prevalence over the years following the reduction in dust levels mandated by the 1969 Federal Coal Mine Health and Safety Act (FCMHSA). These programs are operated by the National Institute for Occupational Safety and Health (NIOSH), and are described in detail in Attfield and Althouse (1992) and Attfield and Castellan (1992). Both studies were divided administratively into distinct time periods, and the results shown here reflect that division. Figure 1 shows the prevalence of CWP 1+ as determined from data from the CWXSP, plotted by time period and years in mining. There is evidence of a temporal reduction in prevalence. (The lack of an obvious decline in the early 1970s may be an artifact arising from use of different versions of the standard classification.) Figure 2 provides information in the same format for PMF, and shows a similar trend [ ]

Jan 1, 1993

By Murat Budakoglu

Albite (NaA1Si308) is one of the important raw materials for the rapidly developing Turkish ceramic and glass industry. Prior to 1980, development of the ceramic industry in terms of raw material was dependent upon small-scale mining operations; in the last decade, these efforts have increased substantially. The aim of this study is to investigate the geochemical properties and distribution of albite occurrences in the Kocayayla district, which is about 12 km northeast of the town of Milas, about 50 km west of the city of Mugla in southwestern Anatolia. Kocayayla is also well known for its famous ancient city, Labranda. The field area is located in the Menderes Massif, which was formed by major tectonic events during the Late Proterozoic and subsequent periods. The target area was studied to prepare a detailed geological map (scale, 1:10,000), and to determine the formation of albite-mica-schist-quartzite borders in the host rock gneiss. To do this, systematic sampling of albite was done in the two main areas, the Sarikaya and Yumruta? regions. In the study area, albite zones are scattered within an area of about 20 km2, and they extend in a northeast-southwest direction; mica-schists and quartzite veins accompany these units. Mineralogical observations show that quartz is the main mineral associated with albite. In the ceramic industry, the albite + quartz assemblage is well known and is classified as "standard" or "super type," depending upon the content of TiO2 and Fe203. In this study, the Sarikaya albites (profile I) exhibit remarkably lower TiO2 (0.15% on the average) values contrasted to that of Yumruta? (profile 11; 0.24% on the average), whereas Fe203 values vary slightly from 0.076% to 0.085% in both regions.

Jan 1, 1999

By G. Tiravanti

A recurrent concern in mining operations is how to deal with the large volumes of fresh water used which in turn generates large volumes of effluents that have to be treated. Water treatment can focus in one of two main strategies: treat the effluent as it is produced, or use a simulation tool to optimize water use in the process and reduce volume of effluents, contaminants concentrations, operational costs, and so on. This article shows a successful tool developed in Matlab-Simulink® that allows modelling a mining process and simulating potential improvements to evaluate the results. This tool has been proven in Cu-Mo operations and recently it has been used in poly-metallic operations. This article reviews the 4 Key Steps required to achieve our goals: a) Elaboration and verification of the mining Operation?s Block Diagram, based on a field survey; b)Model construction and input flows and qualities in selected streams; c)Model Validation and Simulation of new alternatives like recirculation, changes in reagents and dosage, partial treatment, flows merges/separation, and others; d)Development of the Optimal Solution which consists on determining the CAPEX and OPEX.

Feb 27, 2013

By S. J. Ristorcelli

Historically, geologic data has not been adequately considered in resource estimation. More recently, with the use of computers and sophisticated estimation algorithms and geostatistical justifications, geology has been downplayed further. Many reasons are given for not using geology including cost, time and irrelevance. None are valid. Boundaries defining mineral domains should be used in computer-generated resource estimates. Selected case histories show how the failure to honor geology has caused discrepancies in resource estimates of actual in-place resources. After-the-fact differences have included decreases in tonnage of up to 50% and increases up to 300%; partial to complete recategorization of material; and 50% decreases in grade. The costs of gathering and using geology are trivial compared to the potential consequences.

Jan 1, 1994

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By E. A. Laurila

During last years many different types of X-ray fluorescence analysers have appeared in the market most of these instruments being designed for laboratory use. The instruments applied ins continuous processes are usually modifications of these laboratory types. The application of these instruments to the analysis of heavier elements seems to be quite satisfactory. By lighter elements difficulties are caused by the strong absorption of the characteristic fluorescence radiation, which sometimes makes the use of vacuum or helium chambers necessary. In the following an instrument of another type will be described. It has been developed exclusively for the analysis of titanium in ilmenite concentrate, where the content of Ti02 varies between 43 - 46%. Preliminary measurements have shown that in this interval absolute change of 1% in the Ti02 concentration causes a relative change of about 2% in the intensity. Because: the accuracy of 0.5 % Ti02 is sufficient, 1% relative accuracy should be, attained in intensity measurement. The problem is not very easy to solve due to the fact that Ti K radiation is rather soft and the requirement's for accuracy are rather high. Being applied to the analysis during a continuous process may statistically fluctuating variables in connection of sampling and disturbances of many kind set special requirements for the instrument design.

Jan 1, 1960

By James Paone

Subsidence movements have damaged houses, schools, streets, and public utility lines in some undermined sections of Belleville and Maryville, Ill. In cooperation with local officials and the State of Illinois, the Interior Department's Bureau of Mines is sharing experience in backfilling abandoned coal mines to demonstrate that bituminous coal mine workings in south-western Illinois can be successfully backfilled and subsidence-prone areas stabilized. Subsurface investigations revealed that mine workings are dry and underlain by underclay deposits susceptible to instability upon wetting. Backfilling will therefore be accomplished by pneumatic injection instead of the hydraulic methods used in previous subsidence-control projects.

Jan 1, 1977

By P-M. Dupond, S. Lowrie, C. Tauziéde, Z. Pokryszka, A. D. Jones

A physical model has been developed to simulate the flows and mixing of gases in the waste of a longwall retreat coalface. The model is used in conjunction with computational modelling, and the distributions of permeability and gas emission in the model waste follow those in computer simulations (Pokryszka et al 1996). The physical model represents at 1170th scale a 200 m long, 3 m high coalface with a waste extending up to 280 m to the face start line. The model is tilted to the same seam slopes as the real face, e.g. 22° ascensional ventilation along the face and 7" slope to the dip. The purpose is to investigate the flow of three components: ventilation seepage flow through the waste; methane; and nitrogen injected to quell spontaneous combustion. A heavier-than-air surrogate gas (SF,) is used in place of methane, and therefore the model is inverted so that gas layers form along the 'roof". The main forces driving the flows in the waste (pressure gradients due to ventilation and the density difference of gas layers) are kept in proportion by appropriate scaling of the permeability. Calibration and validation used data from a coalface at a mine in the Lorraine coalfield. The model is now in operational use.

Jan 1, 1997

By AKIHIRO YOSHIMURA, HIDEKAZU KATO, KOTA TAKATORI, YASUNARI MATSUNO

Chalcopyrite (CuFeS2) is the most refractory copper mineral when treated in conventional sulfate media leaching systems. This is the first study to examine the use of a dimethyl sulfoxide (CH3SOCH3, DMSO) solution containing copper chloride (CuCl2) for the leaching of chalcopyrite. Leaching experiments for a copper concentrate composed mainly of chalcopyrite were conducted at ambient pressure at 313–413 K. The leaching fractions of Cu, Fe, S, Au, and As were investigated. It was found that 90% of the Cu was extracted in 2 h, and 94% was extracted in 4 h at 373 K, which is competitive with other conventional processes. A DMSO solution containing CuCl2 could selectively dissolve the valuable metals Cu and Au from chalcopyrite, but leave minerals with little economic value such as pyrite (FeS2) and As in the residue. Chalcopyrite is oxidized by cupric ion in proportion to the stoichiometric ratio of Cu in the concentrate to the initial cupric ion in the DMSO solution, which is enhanced by the presence of oxygen below 373 K.

Mar 12, 2021

By Onuralp Yücel, Kağan Benzeşik, Ömür Can Odabaş, Selçuk Kan

Extraction and processing constitute an important area in the metallurgy of molybdenum. Molybdenum trioxide (MoO3) production is one of the most important stages in molybdenum production. In this study, the effects of different furnace types on MoO3 production were investigated by using molybdenum concentrate as a raw material obtained during the enrichment of copper ores. Preliminary experiments have been made using a chamber type furnace, and a transition to a pilot-scale has been carried out with rotary kiln experiments. The effects of a different time and atmospheric conditions on MoO3 roasting kinetics were investigated by experimental studies conducted in the temperature range of 500–650°C. It was determined that the optimum temperature and time for sulfur (S) removal was 625°C and 180 min in the studies carried out in the rotary kiln, and it was determined that 0.61%S content was reached with an average removal efficiency of 98%. The activation energy in these sets was calculated as 89.519 kJ/mol.

May 3, 2021

By Iain M. Mason

Linear meridional zones of bad roof conditions have been frequently encountered in producing collieries working the Permian age Lithgow seam in the western coalfield of New South Wales. The prediction of such zones ahead of mining is desirable for reasons of both safety and economics. In March, 1981, we carried out an experimental, three-component in-seam seismic survey at Invincible Colliery to discover whether such zones have any unambiguous seismic effect. The underground survey was the first of its kind to be attempted in an Australian mine. The data quality was excellent with the spectra broadband and clear. Polarisation analysis disclosed two modes: one compressional; the other shear horizontal. The SH model was clearly dispersive and well gound to the plane of the seam. Modal velocities decreased by up to 15% at the fracture-swarm site. There is a strong suggestion on the RLS maps obtained here that the distributed fault zone is acting as a composite scatterer of channel waves. The P-SV and SH wave tomograms obtained show, in a general way, the distribution of stress in the coal panel.

Jan 1, 1982

By P. J. Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

Flooded-bed scrubbers on continuous miners have been shown to be an effective respirable dust control technology, traditionally used during the extraction of extended cuts of up to 12.2 m (40 ft). To effectively use scrubbers in faces that employ exhaust ventilation, the return ventilation curtain or tubing should be located outby the scrubber discharge on the continuous miner, which results in a setback distance from the face of approximately 12.2 m (40 ft). The goal of this research was to compare respirable dust levels generated in 6.1 m (20 ft) cuts when using extended curtain setbacks with a scrubber operating to dust levels in 6.1 m (20 ft) cuts when using traditional exhaust face ventilation without a scrubber operating. Dust surveys were completed at three mines with area and personal sampling conducted to quantify respirable dust concentrations on a cut-by-cut basis. Sampling results did not show a statistically significant difference in respirable dust at the continuous miner or shuttle car locations with and without the scrubber operating. However, with the scrubber operating, respirable dust concentrations in the return airstream downwind of the miner showed reductions of 91%, 86%, and 40% at Mines A, B, and C, respectively. The reductions at Mines A and B were statistically significant. Likewise, reductions in respirable quartz dust levels in the miner return were observed at all three mines, with statistically significant reductions of over 80% observed at Mines A and B. Consequently, operation of the flooded-bed scrubber did not impact respirable dust levels in the face area but did significantly reduce respirable and quartz dust levels downwind of the continuous miner. These results were obtained with the mines operating at or above the minimum operating levels specified in their ventilation plans.

Feb 23, 2014

By C. C. Harvey

Asia is experiencing a growth market for industrial kaolins for use in ceramics, paper, plastics and other market sectors. Export and import data for the Asian countries reflects this growth with the Peoples Republic of China as the major exporter of clays and Japan the major importer. The growth in tonnage and product sophistication of kaolins produced on Belitung in Indonesia is typical of developments that are taking place in many locations in Asia. This region therefore presents opportunities for mineral processors and a challenge for the exploration geologist, the mineral processing engineer, the mineral economist and the marketing specialist.

Jan 1, 1996

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

By D. L. Leach

This report covers laboratory experiments simulating in situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen. Copper extraction and acid consumption data are correlated with temperature in the range 50-150°C and quenched pH in the range 0.25-2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1975

By R. V. Ramani, C. J. Bise

INTRODUCTION Classification of coal seams as thin, medium, and thick is both subjective and relative and is more a reflection of the statistical mode of the thicknesses en- countered in a mining region. A geological factor more precisely understood as defined than thickness is the inclination of the seams to the horizontal, commonly referred to as the pitch or the dip of the seam. Thick and steeply pitching seams present far more challenges to the ingenuity of the mining men to devise methods for their extraction than the thick and less steeply inclined ones. In a marginal case, where a thick coal seam may be minable by surface or underground methods, the decision bears a close relationship to the technological developments in the mining scene. Near surface thick coal seams are a special gift of nature and are not as wide- spread as the ones that call for the application of under- ground methods. Recent advancements in surface mining equipment have made it possible to surface mine to great depths. Stripping ratios of 30: 1 (cu yd of over- burden removed per ton of coal) have been achieved. The extraction of thick seams which preclude the use of surface methods is the concern of this chapter. Specifically, the objective here is to outline the special technological factors in underground mining of thick coal seams and to illustrate through several case histories the methods that are practiced in the North American continent. For the purposes of this chapter, a thick seam is defined as one which is not readily minable with currently available equipment without modifications to the extraction method or the equipment. At the present time, a thickness of 4.8 m (16 ft) can be considered as the lower limit, although developments in equipment and methods can be expected to push this limit upwards. The data for the case histories were collected from two extended mine visits in 1975 and 1978, and from other published accounts of the mines visited. Reference is drawn particularly to reports by Bise, Ramani, and Stefanko (1976) and Rarnani and Kenzy (1979). THICK SEAM MINING METHODS The various methods of mining thick seams can generally be grouped into three major categories: full face methods, where the entire thickness of the seam is re- covered in a single pass; slicing methods, where the seam is extracted to its full thickness by horizontal or inclined slices either in an ascending or descending order; and caving methods, where the seam is undercut and the en- tire coal seam is recovered by caving the top coal into the excavated cut, or some variations of the basic sub- level caving method. As shown in Table 1, in each of these methods, the coal is removed by either room-and-pillar or longwall methods. Hydraulic mining and transport of the coal in open flumes or in pipelines are also practiced. Addition- ally, the void created by the removal of coal may be filled with a packing material (stowing) except in the caving methods. The pitch (dip) of the seam, particularly when it is greater than 0.26 rad (150), imposes severe operational limitations on mobile equipment. A more detailed general discussion of the methods can be found in Bise et al. (1976) and Vorobjev and Deshmukh (1964). Specific discussion on the many variations of the three basic methods can be found in the papers presented at the international symposia that were held in

Jan 1, 1982

By R. H. Grau

This Bureau of Mines report describes methane liberation trends from all U.S. coal mines liberating over 100 Mcfd (100,000 cfd) (2.8 Mm3/d). Detailed are results from the latest Bureau survey performed in 1985 and shown are mine and company name, location, coalbed and methane liberation quantity. The report shows that in 1985, there were 180 mines producing more than 100 Mcfd (2.8 Mm3/d) and the total quantity of methane liberated by these mines was 303,900 Mcfd (8,605 Mm3/d). This data is compared with previous studies performed in 1971 , 1973, 1975, and 1980. From 1971 to 1985, there was a 10% decrease in the number of mines liberating at least 100 Mcfd (2.8 Mm3/d) but there was a dramatic 34% increase of liberations from these mines. The increase seems to be caused by new mines being developed in deeper, gassier coalbeds, particularly in Alabama. Likewise, in comparing the ten highest liberating mines in 1975, 1980, and 1985, an increase in methane liberations each year was experienced. The report classifies mines by three levels of liberations: greater than 100 Mcfd but less than 500 Mcfd (2.8 to 14 Mm3/d); 500 Mcfd to 1 ,000 Mcfd (1 4 to 28 Mm3/d); and greater than 1,000 Mcfd (>28 Mm3/d). It was found that 87% of liberations were from mines producing over 1,000 Mcfd but these accounted for only 38% of all the mines in the study.

Jan 1, 1987

By Georgy Cherkashov, Svetlana Babaeva, Tamara Stepanova, Firstova. Anna

Seafloor massive sulfides (SMS) study in the Russian Exploration Area at the northern equatorial Mid Atlantic Ridge began after signing the contract with International Seabed Authority in 2012. In order to evaluate the SMS resources in the course of exploration the major and rare metals with economic value should be determined. The evaluation is based on geochemistry and mineralogy and particularly on the type of rare metals occurrence in the SMS. As a case study research of the Semyenov cluster of SMS deposits have been conducted.

Sep 1, 2014

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015