Search Documents

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By Gary B. Hemphill

The 345 km long Taiwan High Speed Rail Project will connect the island’s two most populated cities, Taipei and Kaohsiung. Kaohsiung is the world’s third busiest port. The 23 km of alignment on Contract C230 requires the construction of 5,879 m of shallow mined tunnels ranging from 137 m to 1,285 m in length. All nine of these tunnels are mined using NATM methodology. Two of the tunnels, T01 and T08 are in the Toukoshan Formation. This paper will discuss the mining methods, ground support design, and the instrumentation installed to monitor and verify its effectiveness in the two aforementioned tunnels.

Jan 1, 2003

By Cesar A. Busnardo

The carbonatite orebody in Jacupiranga is situated some 230km (140-mi) southwest of Sao Paulo and is mined by Serrana S/A de Mineragao, producing an apatite concentrate for fertilizer production and a calcite tailing for cement manufacture (see Figure 1). The orebody (Table 1) is mined by open pit and the total production is 4.5 million mt/year of carbonatite ore with a further 2.2 million mt/year of overburden. The carbonatite low-grade ore (Table 2) is fed to the concentration plant at 460 mt/h , comprising of four parallel lines of grinding, by rod mills 2.7m x 4.5m (9 x 15-ft), operating in closed circuit with hydrocyclones. The grinding circuit product is deslimed in four stages using hydrocyclones and the deslimed product is conditioned with corn starch and subsequently floated, using fatty acids as collector to, recover the apatite.

Jan 1, 1985

By L. W. Teal

The Paupers Dream Property is located in the northern Boulder Mountains, southwestern Montana, 30 km southwest of Helena. The property is situated in the central portion of the Butte-Helena gold belt, a NE trending lineament marking a zone of recurrent, late-Cretaceous to mid-Tertiary volcanic activity. Geology consists of a plutonic basement of late-Cretaceous quartz monzonite overlain by a pre-volcanic basal conglomerate and a complex sequence of Oligocene rhyolitic volcanics. Gold mineralization occurs in fracture-controlled quartz veins, silicified stockwork, and brecciated shear zones as auriferous pyrite, arsenopyrite, and disseminated free gold. An estimated 60,000 tonnes averaging 2.5 g/t was produced from the Porphyry Dike, Venus, and Paupers Dream Mines on the property. Current drill indicated reserves (May, 19861 are placed at 6,946,000 tonnes averaging 1.45 g/t gold.

Jan 1, 1987

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By James Barker, Jacques Renault, Chris McKee

Previous XRD work by us (McKee, Renault, Barker; 199Oa, 1990b) showed that by using pressed powder briquettes and a peak deconvolution technique, quartz in perlite can be routinely determined at <0.1 wt. %. In the present report, we discuss two additional methods of standardization: 1) chemical determination of quartz in silicate standards and 2) addition of a large amount of quartz to an unknown mixture. The first method applies the concept of mass balance and is sensitive to the analysis of silica and a monitor element. The second minimizes mixing errors; its equation is non-linear and is derived from the two component case with unequal mass absorption coefficients treated by Klug and Alexander (1974).

Jan 1, 1991

By E. Azrag, A. MacDonald

A hydrogeologic investigation was conducted to predict inflow to underground mine workings and mining-induced hydrologic impacts for a proposed underground mine beneath a lake in northern Canada. Flow and shut-in tests were conducted to determine hydraulic conductivity values and to estimate the hydraulic head. A conceptual hydrogeologic model was developed and incorporated into a numerical ground-water flow model (utilizing MINEDW, a three-dimensional, finite-element code with special attributes designed for mine dewatering). The mining sequence was represented in detail(e.g., driving ramps and drifts, extracting panels, and backfilling mined areas). Due to limited field data, a quantitative assessment of uncertainty was implemented to estimate limits of possible inflows.

Jan 1, 2003

By Z. T. Bieniawski

In the past 15 years, rock mass classifications have experienced unprecedented development and have emerged as powerful practical methods for assessing ground conditions and tunnel support. Such methods as the RMR System (Geomechanics Classification) and the Q-System have provided many advantages over the classical Terzaghi rock-load method introduced in 1946. These new classifications have found wide applications all over the world but some doubts have been expressed and shortcomings pointed out. The author, who developed the RMR System, takes a penetrating look into the promises and the pitfalls of modern rock mass classifications. He dispels some misconceptions and shows how rock mass classifications can serve as effective and dependable design aids in tunneling.

Jan 1, 1987

By K. Galos

The paper presents increasing importance of mineral secondary and waste raw materials in the minerals management in Poland. Definition of mineral secondary and waste raw materials is proposed, according to current Polish law. On this basis, sources of various types of mineral waste raw materials are analysed. The special attention is paid to the wastes from mining and processing, wastes from power plants, and wastes from steelworks and other smelters. Other types of waste and secondary materials, such as metallic containers, glass containers, batteries, metallic wastes and scraps, are also taken into account. Analysis of sources of such materials is shown together with the main directions of their economic use. Available sources of information on manufacture and use of the mentioned secondary and waste raw materials are also analysed. Finally, for a wide range of waste materials, their current and expected significance as substitutes for some industrial and construction minerals in Poland is given.

Jan 1, 2011

By Arne M. Myrvang

Rock stress measurements have been carried out by the Mining Department, the Norw. Institute of Technology (NTH) since 1964. Before that time rock stress measurements were carried out at a few locations by the Swedish professor Hast as early as 1958. From the very beginning the NTH engagement in the rock stress measuring field has been very practically aimed, and we have all the time enjoyed a very good cooperation with the Norwegian mining industry. At a very early stage the industry realized that proper measurements with proper equipment could be a very valuable practical tool. Hence the industry also was willing to grant considerable funds for the education of experts and development of measuring techniques. Since 1964 measurements have been carried out in the great majority of Norwegian mines. During the last years a large number of measurements have also been carried out in connection with hydro-electric power plants, road tunnels etc.

Jan 1, 1981

By Peter Halbach

Cobalt-rich ferromanganese crusts are one type of the two oxidic metallic mineral resources in the deep ocean that incorporate metals supplied and transported from both land (aerosols, continental run-off) and sea sources (oxygen-minimum zone, hydrothermal alteration of the oceanic crust). The substances directly precipitate from cold seawater under more or less oxic conditions and form thin layers (2 up to 25 cm thick) on hard substrate rocks like volcanic hyaloclastites, weathered basaltic rocks and/or carbonate-fluorapatite; in the crusts many metals therefore exist in the highest state of oxidation. Deposits of the Co-rich ferromanganese crusts are found throughout the global oceans on the flanks, terraces and summits of seamounts and submerged volcanic mountain ranges and platforms, where the ocean currents have kept the seafloor more or less free of sediment for millions of years. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical and surface-chemical mechanism. Elements in seawater may occur as dissolved hydrated ions or as inorganic as well as organic complexes which in general have either a positive or a negative surface charge depending on the pH of the respective aqueous environment. Those complexes may form hydrated colloids that interact with each other and with other dissolved hydrous metal ions. Hydrated cations such as Co, Ni, Zn, Sn are, for example, attracted by the negatively charged surfaces of colloidal hydrous Mn-oxide particles, whereas hydrated anions (e.g. oxyanions) and elements forming larger complexes with low-charge densities (e.g. U, As, Th, Hf, REE) are attracted by the slightly positively charged hydrous Fe oxihydroxide particles.

Jan 1, 2008

By Y. C. Kim

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that Ordinary Kriging (OK) cannot easily handle. With the recent introduction of the nonparametric, distribution-free technique of Indicator Kriging (IK), the above problems can be solved. This paper describes the results of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blast hole information. The IK estimator, although a bit optimistic, performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel&apos;s average grade. Under this criterion. OK was found to be very biased and pessimistic.

Jan 1, 1986

By BERND SCHÖNHERR, JÖRG DEHNERT, PETER WINDISCH, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposure of miners in Germany, especially during remediation work in old mines. The QESS is a lightweight, modular and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil and expanding foam. It is designed to seal off radon-rich parts of galleries within minutes. Originally, the QESS was developed to protect miners against radon exposure. Then, the QESS found the attention of several mine rescue teams at a German mining conference. Some mine rescue drills by The Student Mine Rescue of the Technical University Bergakademie Freiberg, Wismut Mine Rescue and Front Range Mine Rescue helped to improve the system and highlighted its potential for mine rescue operations. Now, the QESS is well-suited for small-scale mining. The QESS can be used to both protect miners from radon exposure and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

By A. W. Khair

This paper deals with the causes and mechanisms of pillar failure in a southern West Virginia coal mine. The conclusions are based on in-mine observations and analysis of mining methods, eyewitness account of the sequence of events, topographic and geologic conditions, and mechanical properties of mine roof, coal, and floor. The study indicated that massive pillar failure was caused by the collapse of the mine roof. The collapse of the mine roof was due to the combined effects of high lateral compressive stress and high extraction ratio causing excessive bending of the roof beyond its limit. It was assumed that the higher lateral compressive stress under such a shallow cover was probably due to the drastic change in the structural geology of the area and possible residual stresses. Eased on the analytical study it was concluded that the sudden release of elastic energy (shock) due to the rupture of the roof caused the squeezing of approximately eighty mine pillars.

Jan 1, 1983

By B. K. Cantrell, D. H. Carlson, W. F. Watts, K. L. Rubow

The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH) regards "whole diesel exhaust" as "a potential occupational carcinogen." Threshold limit values (TLVs) are recommended for the gaseous pollutants CO, CO2, NO, N02, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality. Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulageway and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2 and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters. Concentrations of CO, C02, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3.

Jan 1, 1992

By R. Shields

"Hard rock mines move large volumes of material, which can cause the conveyors that are essential to this movement to suffer lots of problems, including carryback, spillage, dust and belt wander. Many of these issues are created at the transfer points where the belts are loaded.This article provides an overview of the latest transfer point systems that incorporate safety and serviceability by design as well as a report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, NV. Here, performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine.The importance of transfer pointsConveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance is the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created.The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material — cargo released in the form of carryback, spillage or airborne dust — that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems and issues with community relations. The U.S. Mine Safety and Health Administration estimates that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points.Technologies to improve transfer pointsA number of techniques to improve the performance of conveyor transfer points have been developed. They include:"

Jan 11, 2017

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

The declining grades of surface deposits have re-confirmed the need for greater production rates. Large scale production requires increased investments in expensive and sophisticated equipment. The key to successful operations can depend entirely on proper equipment utilisation and in this program of research at the Department of Mining and Metallurgical Engineering, University of Queensland, much emphasis has been placed on the analysis and improvement of this aspect of a load-haul-dump operation. For a model to be successfully integrated into a mine engineering function and readily accepted by mine operating personnel, it has to offer more than just results. The concepts used in its design and construction must include sufficient detail to enable engineers to apply it usefully and with confidence.

Jan 1, 1979

By C. Ptacek, D. Hiller, J. L. Janbor, H. Mccreadie

Between 1991 and 1994, metallurgical residues from a pressure-oxidation autoclave at the Campbell Au-quartz mine at Red Lake, northern Ontario, were neutralized with dolomite-rich flotation tailings and were deposited in a polyethylene-lined disposal area. Mineralogical analysis indicates that most of the As occurs as a crystalline ferric sulfarsenate, and some is associated with Fe oxides and with K-H3O jarosite. Field pore-water geochemical data from 1994 and 1995 showed increases in Fe(II) and As(III) concentrations, suggesting that the sulfarsenate and jarosite are dissolving; none of the discrete As phases included in a thermodynamic database limit dissolved-As concentrations, and these concentrations may continue to increase. These results demonstrate the potential for Fe and As loading through groundwater systems.

Jan 1, 1998