Search Documents

By John Songstead

INTRODUCTION The Bunker Hill mine, located at Kellogg, ID, in the Coeur d'Alene mining district, has been a major pro¬ducer of lead-zinc-silver ore since 1887. Since its dis¬covery, it has produced over 25 401 171 t (28 million st) of ore from 20 to 25 veins and ore zones. The mine now covers an area of approximately 1.609 km (1 mile) in length and 0.8 km (1/2 mile) in width and extends from 1097 m (3600 ft) above sea level to 488 m (1600 ft) below sea level. Production is presently at a rate of 1542 t/d (1700 stpd). During 1965, a new stoping method, the Bunker Hill pillar system, was developed to enable the profitable mining of large, low-grade zinc ore bodies. The system was specifically designed to in¬corporate the Atlas Copco T26GH rubber-tired loaders. High productivities were achieved, and the method was adapted for mining the higher grade stopes where large timber square sets are utilized. This results in nearly 100% extraction. GEOLOGY The area encompassing the Bunker Hill mine lies immediately south of the Osburn fault, a major east-west striking, deep-seated strike slip fault which is the dominant structural feature in the Coeur d'Alene district. The Bunker Hill forms a series of veins and mineralized zones which occur as link structures, tension fractures, and breccia zones in folded, interbedded argillaceous quartzites of the Revett and St. Regis formations of the Precambrian belt series. The Rosco ore body is predominantly a zinc ore body above the Cate fault, which is presently known to occur from the 13 level. [elevation 488 m (1600 ft)] to the 1600 level [elevation 304 m (1000 ft) ]. These ore bodies are stringer zones with at least one dominant 1.8 to 4.5 m (6 to 15 ft) wide band of ore. They dip 0.09 to 0.26 rad (5° to 15°) steeper than the local 0.61 rad (35°) dip of the Cate fault, and also deviate 0.26 to 0.52 rad (15° to 30°) in strike from the Cate. Because of the flat dip and fractured weak hanging wall, normal cut-and-fill mining has not proven practical in this ore body. The mechanized timber methods described in the next section and the Bunker Hill pillar system are the mining methods successfully used. MINING METHODS While pillar stoping and mechanized cut-and-fill stop¬ing methods were obviously superior to the widely used timber stoping methods, as far as cost and productivity

Jan 1, 1982

By S. K. Kawatra, T. C. Eisele

A horizontal-baffle arrangement has been developed to prevent excessive axial mixing in flotation columns. These baffles have been shown in previous work to improve the grade/recovery performance of both a laboratory-scale column and a pilot-scale column (Kawatra and Eisele. 1993). In this paper, results are given for continuous on-line operation of the pilot-scale baffled column in a commercial coal- cleaning plant. These results show its ability to operate for extended periods without plugging, to produce a consistent-quality product even while the feed quality was fluctuating, and to remove much of the pyritic sulfur from the coal.

Jan 1, 1995

By J. Bigu

Ventilation conditions in working environments are usually studied by anemometry or, in complex cases, b using special tracer gases such as SF6 and 85Kr. in conjunction with chromatographic and radioactivity techniques, respectively. In some working environments, such as underground uranium mines, however, use can be made of the natural radioactivity environment (e.g.. 222rn. 220rn, and their progeny) to investigate mine ventilation conditions of practical interest. Theoretical studies and experimental data in several underground uranium mines and mine locations show that certain thoron progeny to radon progeny concentration ratios are very good indicators of ventilation conditions. Furthermore, the growth and decay of radon progeny and thoron progeny provide valuable information on mine air residence and clearance times. Some specific examples have been analyzed, such as bacterially-assisted uranium leaching operations in a partially enclosed stope, and the effect on the underground environment of turning ventilation fans on and off for a period of time. Air residence times and other variables of interest, determined from the mine radioactivity environment, were compared with more traditional techniques, such as anemometry and tracer gas chromatography. These studies were also extended to a wet non-uranium mine which exhibited relatively high concentrations of radon and its progeny.

Jan 1, 1989

By O. J. R. Baena, I. C. Sánchez, J. L. G. Guzmán

Frontino, a municipality in western Antioquia, Colombia, has more than 200 years of mining tradition. Currently, mining activities are carried out for lode gold using subway tunnels, where the grinding of the material is done in "cocos", whose energy depends on internal combustion engines and ACPM, environmentally polluting and inefficient methods. In accordance with the Sustainable Development Goals as an initiative developed by the UN, different mining methodologies that are aligned with these are constantly being analyzed. This study proposes to eliminate the use of hydrocarbons in artisanal mining, mainly promoting Sustainable Development Goals 7, 9, 11, 12, and 13. This will be achieved through an energy transition to renewable energy sources that take advantage of the topography and water resources of the area, providing advantages to the communities that live there, such as lighting, electricity for cooking, ventilation for mines, etc

Mar 2, 2022

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By G. Brooker

The back-filling operation at Olympic Dam mine supports a 9.8 million tonne per year (Mtla) underground Longhole Open Stoping operation. It involves a combination of Cemented Aggregate Fill (CAF), Surface Rockfill and Underground Rockfill. The fill material is introduced from the surface via bore-holes into the top of the stopes. Due to the deleterious effects of the dust and the thickness of the atmosphere in the stope it is not possible to view the filling process. The need for a means to measure the filling process is driven by the stopes, which have both rock and CAF fill placed in them. The large volumes and high relative cost of CAF makes the minimization of CAF fill a business priority. Incorrect filling can lead to the sterilization of ore reserve. The use of millimeter wave radar to view through the haze to give real-time data on the relative positions of the different fill masses is being developed as an in-stope fill control device. This paper reviews the salient points of the technology and its potential use in the back-filling operation at Olympic Dam. The broader potential of this technology for use in the mining industry by 'seeing' through water and dust laden environments such as that found in stopes and ore passes is discussed.

Jan 1, 2001

By C. Zhou, J. Srednicki

Electronic systems have been increasingly used in underground mines to improve mine safety. These electronic systems emit electromagnetic (EM) energy which can adversely impact the performance of other electronic systems nearby and thus should be characterized. Researchers at the National Institute for Occupational Safety and Health (NIOSH) characterized the magnetic fields emitted from devices that can potentially interfere with the performance of proximity detection systems (PDSs) and compared the emission levels of these devices to the susceptibility of PDSs. In this paper, we present our measurement results pertaining to this effort. Particularly, magnetic fields emitted from the different orientations of a powered air purifying respirator (PAPR) and two lite trackers are evaluated based on the RE101 protocol specified in the MIL-STD-461G standard. The results show that both devices emit strong magnetic fields which strongly depend on the orientation of the devices. At some frequencies, the maximum emission levels from the two devices exceed both the emission limit given in MIL-STD-461G and the maximum magnetic fields that a PDS can withstand without a failure. The results and findings in this paper can help the mining industry better understand electromagnetic interference (EMI) underground and provide critical scientific data that support mining-specific recommendations to address EMI-related challenges.

Feb 1, 2023

By V. B. Achanti, A. W. Khair

Developing a laboratory procedure for the determination of coal-seam compressive strength has been a subject of discussion for many decades, and the reliability of laboratory determinations is often the subject of debate. A coal seam’s characteristics, the method of sample collection, the specimen preparation method and the testing procedure can often result in drastic variations in the test results. In this paper, the development of a laboratory testing procedure for the determination of coal-seam compressive strength is presented. Two samples that were collected from different coal seams were tested in this study. First, the inherent characteristics, i.e., coal structure. Hardgrove grindability index (HGI), Slake durability index, proximate analysis and mechanical properties (Young's modules and Poisson's ratio), of each coal were determined. The results were used to categorize the coal scams in terms of the characteristics liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes, cylindrical and cubical, were tested to determine which shape produced the most reproducible strength values. Third, four loading rates within the static testing range, i.e., 0.007, 0.07, 0.34 and 0.7 MPa/s (1.0, 10, 50 and 100 psi/sec), were used to determine the ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics, were established. Background Laboratory testing of coal specimens for the determination of seam compressive strength has been a subject of discussion since the early 1900s. Many researchers have tested coal specimens to estimate coal-seam compressive strength for use in pillar design to insure the safe operation of [ ] mines (Unrug et al., 1986; and Hirt et al.. 1992). Yet, there is a lack of a universal procedure, and, no matter which approach is used, it becomes the subject of intensive debate. A great deal of work has been performed on the subject, and there is much information available in the literature. Some of this work concerns quantifying the influence of specimen shape and size on compressive strength (Bieniawski. 1968: Barron et al.. 1992: Khair and Xu 1994; and Khair 1994). As indicted in the literature, coal is a heterogeneous material, consisting of discontinuities such as cleats and bedding planes, which are likely to produce variable strength results (Holland, 1964; Unrug et al., 1986). Some of the prominent issues that influence the determination of coal-seam compressive strength in the laboratory are: •the collection of a representative sample from a coal seam; •the geometry, i.e., shape and size of the specimens to be prepared and tested: •the loading rate at which the specimens are to be tested:

Jan 1, 1997

By R. C. Bunge

The selective flotation of semi-soluble salts with fatty acids is often negatively affected by the interaction of the potential determining cation with the ionic surfactant in bulk solution. This problem can be avoided by floating at low pH which involves the emulsification of the collector. The research presented here focuses on the influence of the Ca2+ ion on the flotation of fluorite with palmitic acid at low pH. Our results show that the surfaces of collector emulsions are dominated by precipitation phenomena similar to those encountered in bulk. In turn, fluorite in palmitic solution at intermediate pH displays surface properties similar to those of the collector by itself. This may be due to two alternative mechanisms (i) adsorption of bulk precipitate on the fluorite surface or (ii) the formation of a bilayer of surfactant ions on fluorite. Possibly, both mechanisms occur simultaneously.

Jan 1, 1993

By Friedrich Steinhäusler

RADON SOURCES AND CONTROL MEASURES IN THE MINING ENVIRONMENT Most of the contamination of the mine atmosphere by radon 222 is due to radon emanating from solid or fractured ore surfaces of walls, roof and floor. Also radon gas emanates from broken ore either from storage in backfilled mined-out areas as applied in e.g. shrinkage stopping methods or from ore spillage along intake airways mainly due to the use of trackless haulage. To a lesser extent water itself can represent an additional source of radon, which emanates into air from open drainage ditches or seepages along intake airways. The contribution from water can be controlled effectively by isolating the water from the primary intake air system, e.g. by diverting the water through pipes and/or sealing of seepages by grouting. However, control of radon emanating from rock surfaces creates a major technical problem with significant impact on the economic aspects of mining operations, if adequate radiological conditions must be maintained. Basically this can be achieved by suppressing the emanation process itself, confining already emanated radon or by removal of radon from the mine atmosphere. Extensive research has been carried out on the rate of radon emanation as a function of barometric pressure changes (Pohl-Rüling and Pohl, 1969). It could be shown that the radon supply consists of a permanent and variable component. The former results from the surface of the rock and depends mainly on the emanating fraction of its radium 226 content; the latter originates from within the rocks and is a function of the suction effect of decreasing barometric pressure, rock porosity and fissures. The practical application of this barometric pump effect for depressing the rate of radon emanation, e.g. by pressurizing the mine atmosphere, is limited due to high costs for providing a sink for absorption of radon and air as well as lack of permeability in most uranium ore bodies (Schroeder et al., 1966). Mine air cleaning by removal of radon can be achieved with the use of cryogenic methods, chemical removal, adsorption into charcoal beds, use of a gas centrifuge or general ventilation techniques. Technical problems have so far prevented the application of any of these methods other than ventilation. It is common practice to use the age-of-air concept, i.e. fresh air is delivered to the worker as directly as possible and removed quickly afterwards thereby maintaining the air "young". Engineering principles for quantity distribution of air through underground working areas are straightforward for general mining situations where radon constitutes an environmental contamination problem. However, in cases of high uranium ore content this concept may result in high costs with regard to installation and energy requirements for effecting both frequent air changes as well as sufficient heating of the air in cold seasons. Taking into account that the investment in ventilation systems is a major cofactor for the overall ore production costs this can be a limiting and decisive component in the assessment of the economic feasibility of specific mining operations and mineral reserves in general. Effective control of the radon flux from the rock surface prevents the initial contamination of the mine air with radon directly at the source. A radon diffusion barrier for practical application in mining requirements should fulfill the following requirements: - reduction of radon emanation rate by at least an order of magnitude - high mechanical strength - ease of sealant application onto surface to be coated - water resistant - low fire hazard - resistant to temperature changes encountered in mines - high cost efficiency in relation to exposure reduction achieved (direct and indirect costs) - low degree of maintenance. In the past several materials have been tested as sealants for controlling the emanation of radon from surfaces of rock and building materials. Epoxy paints reduce radon emanation rate only by a factor of 2 to 6 (Auxier et al., 1974; Eichholz et al., 1980; Keith Consulting Engineers, 1980). Although it is possible to prevent the escape of more than 99 % of the radon to the environment with gel seals over 80 mm thick (Bedrosian et al., 1974), practical applicability is very limited. Multilayer coatings of epoxy resins with various additives require meticulous preparation and flawless application of seamless four-layer coatings in four days to impede radon diffusion (Culot et al., 1976), otherwise results from this method have not been totally satisfactory (Leung, 1978). Aluminium foil laminated with polyethylene and paper on each side is under test as radon barrier but results are not available yet (Ericson, 1980). However, this method has the inherent disadvantage that possible malfunctioning electrical installations can cause fire or electrical shock through the sealant. Polyurethane foam coatings have been used on stoppings as very effective sealants. It does, however, represent a potential danger of spontaneous ignition and it is expensive (Rock, 1975). Thus, there is still need for a material which has similar properties as outlined above. In the following results are reported from investigations on the suitability of various materials as radon diffusion barriers.

Jan 1, 1981

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of ‘handling supplies or material, load and unload’ and ‘moving power cables.’ Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods – the mobile manipulator, the in-mine hoist, and a cable-handling system - being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

Jan 1, 2005

Horizontal stress is an important factor that contributes to roof failure during a long wall entry development, especially when the immediate roof is weak. In this study, the effects of the three factors, the stress angle between the maximum horizontal stress and entry development, the stress ratio of the maximum to the minimum horizontal stresses, and the sequence of entry development, on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method, when the horizontal stress is fixed. The results have confirmed that the stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the angle is about 60°_75°. The stress ratio has little effect on the roof stresses. In addition, the sequence of entry development has also little effect on the roof stress for the specific case analyzed.

Jan 1, 1999

By B. Qiu, Y. Luo

Longwall and/or room-and-pillar mining operations in multiple coal seams may not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize underground mine structures and subsequently induce additional strata movements. Mathematical models to use the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations, as well as the mining interactions associated with multiseam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multiseam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multiseam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

Calcite has found many applications in the industrialized countries recently, such as filler for paper, paint, plastics, rubber and food. Furthermore, calcite separates many toxic elements, and thus it is used in water treatment, and it is also used to raise the pH of drinking water. Due to its special features, calcite has been characterized as a useful coating and reinforcement filler for applications. Finer particle size of calcite has been determined to provide improved features for all of these applications. For submicron particle production, wet milling is selected over dry milling to produce finer particle sizes. Wet stirred media mills are also used in many industries. For that reason, this study investigated the effects of operating parameters on particle size reduction in the wet grinding process. The knowledge acquired by this study will allow the finding of optimal operating parameters for a stirred media mill to optimize specific energy consumption and reduce particle size.

By Michael A. Redfearn

The use of nitrogen in molybdenite flotation circuits is a relatively new concept utilized by only a few mines around the world. This paper briefly discusses circuit chemistry and the reason for its success. It follows the entire testing process which resulted in a sodium hydro-sulphide dosage reduction from 18.5 to 4.4 lbs/ ton (9250 to 2200 g/t) through to the final installation of an inert gas generator which will produce reagent savings in excess of one million dollars annually. A description of the various types of nitrogen generators commercially available is included.

Jan 1, 1983

By R. Jin

Fine coal flotation using gaseous carbon dioxide has demonstrated the potential for producing superclean coal. The success of this new flotation .procedure is attributed to the coal's high adsorption potential for CO2. To understand the nature of gas-phase CO2 adsorption at the coal surface, in-situ FTIR spectroscopy in a controlled-environment chamber with an ultravacuum sys-tem has been used and the results are discussed in view of other experimental results from differential scanning calorimetry. It has been found that specifically adsorbed CO2 molecules at the coal surface are polarized and have a characteristic doublet at 2336 and 2361 cm-1. Two adsorption states have been proposed to account for the doublet observed from in-situ FTIR spectroscopy measurements. It is believed that the band at 2336 cm-1 originates from the activated site adsorption of CO2 and that the band at 2361 cm-1 arises due to the molecular aggregation of CO2 within the coal pores.

Jan 1, 1988

By Rodrigo Peroni, Euler Victoria

Knowing the depth of contacts between weathering zones in phosphate mines is determinant to define the stripping ratios and the mineralized zones. Contacts are gradational and difficult to define even in the drillhole samples, so the combination with geostatistical simulation techniques helps to define the contact zone and the grade distribution, providing a way to assess the probability of the occurrence and the positioning of contacts between the barren waste and the ore zones. These inputs are used in the scheduling, anticipating risks associated with mine planning scenarios. The results from an application to a case study showed a good improvement when compared to traditional techniques.

Jun 25, 2023

By James P. Rider, Robert P. Vinson, Fred N. Kissell, Jon C. Volkwein, Gregory J. Chekan, Jay F. Colinet

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of lightscattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) has evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2005