Search Documents

By VASU GANGRADE, Marcia Harris, Kumar Vaibhav Raj, Jim Addis, Khaled Mohamed, Snigdha Sarkar

The National Institute for Occupational Safety and Health (NIOSH) conducted a ventilation assessment for a recently established underground room-and-pillar stone mine implementing split-mine ventilation. The primary objective was to examine the impact of the length of the in-place stone stoppings on face ventilation efficiency. These stone stoppings serve to separate the intake and exhaust entries and align with the mining direction. To achieve this, computational fluid dynamics (CFD) modeling was utilized. The appropriate turbulence model was selected, and a mesh convergence analysis was conducted for the CFD model. Following that, the CFD model was validated using the conducted ventilation surveys. Two configurations of in-place stone stoppings, designated as Layout-I and Layout-II, were simulated using the validated CFD models. Layout-I featured a shorter in-place stone stopping, while Layout-II had a longer one. The results obtained from the CFD models demonstrated that the increased length of the in-place stone stopping in Layout-II resulted in a notable enhancement in ventilation efficiency at the advanced faces (last stopping), elevating it from 4% in Layout-I to 8.4% in Layout-II. However, no significant impact of the in-place stopping layouts was observed at other faces. In general, Layout-II exhibited a greater circulation of air at the outby stoppings.

Feb 1, 2024

By Z. Zhang, M. S. Gonzalez, M. de P. Bueno, P. Holopainen, S. Luukkanen

In an extremely competitive mining industry, onsite experience is a big advantage. Mining education at the universities is mostly focused on theoretical studies without a possibility of practical training in mining sites. Hence, experimental mines suitable for practical education are needed to provide a platform for systematic research and education in industrial scale and for training in real mining conditions. Yet, this kind of mine sites is rare worldwide. Thus, a new educational research project, namely MINETRAIN is introduced in this paper evaluating the transition of the Pyhäsalmi mine in Central Finland from an active base metal mine to a research, educational and training underground facility. The uniqueness of MINETRAIN compared to other test mine programs is that the existing state‐of‐art infrastructure in Pyhäsalmi enables research and training facilities among all disciplines related to the overall mine value chain. Though all the above sound interesting in the context of research and education purposes, in practice Pyhäsalmi will have to become an experimental mine that can be sustainable in the future. Accordingly, a prefeasibility study is being conducted and some preliminary results are presented in this paper. INTRODUCTION Despite being a field of studies that requires practical knowledge and experience, mining engineering education follows the same pattern in most mining universities around the world; consisting of theoretical courses and laboratory-based practical modules (Mischo, 2015). The possibility of having practical training in real mining conditions on actual mine sites or processing plants is limited to none, while the only contact that undergraduate students have with mining operations during their time of studies is usually through short-time internships or visits in the context of educational trips. Yet, real integration between universities and the mining industry may be scarce, which does not help students to observe the actual processes, and thus understand the whole picture of mining operations. Indirect practical training is also possible nowadays that technology is shifting from mechanical to digital, and the use of virtual reality -in the context of Mining 4.0- can provide additional experience to the learning process. However, virtual reality is limited to the visual impression and is also limited in actions (Binder et al, 2018). In any case, when there is not a proper pragmatic view of how the different disciplines link to each other and especially if there is a lack of communication, unfortunately the results could be seen at a later stage in the mines as a poor performance of professionals and workers. Another major challenge for educating specialists in the mining sector is that experimental mines suitable for practical education, where the skills and know-how could be developed and/or enhanced are rare worldwide. Such research and educational (R&E) facilities are practically former metal ore mines that have been transformed into experimental sites. Besides being limited in number, not all facilities of this kind serve both a research and educational purpose.

Jan 1, 2019

By T. C. Vogt

The past history of uranium production has been dominated by strip and shaft mining methods, but recently in-situ leaching has emerged as a viable alternative for uranium recovery. (1-8) Mobil was the first company to start in-situ uranium leaching in New Mexico. Mobil's Crownpoint project areas are in Mdinley County and are part of the Grants Mineral Belt. The major uranium deposits in this area occur in the Westwater Canyon Member of the Jurassic Morrison Formation. (9-11) The ore depth at the Crownpoint project is about 2000 ft. In an earlier paper we discussed the uranium mineralogy of an areally broad sampling of Crown- point ore. (12) The organic carbonaceous material often associated with the coffinite ore was characterized in some detail. The organic material appeared to be a very mature, coaly-type kerogen derived from plant components. This result was consistent with other studies on such carbonaceous material. (13-15)

Jan 1, 1981

By A. P. Mehta

The role of microorganisms in the leaching of metal sulfides is well established (Torma, 1977; Murr, 1980). However, this established knowledge applies mostly to chemolithotropic microorganisms such as Thiobacillus ferrooxidans which function optimally in leaching catalysis between 25-35° C, and in a pH range of 2-2.5. Although leaching with thermophilic microorganisms capable of extending the range of catalytic viability beyond 35° C is also documented, there are few if any attempts to optimize or extend sulfide concentrate leaching with thermophilic microorganisms. When mixed metal sulfides or other materials having different rest potentials (referenced to the standard hydrogen electrode, SHE, in the electromotive series) make contact in a conducting, aqueous medium, the contacting members will act as an electrochemical cell, with the member having the higher rest potential assuming the role of an electrical cathode. In leaching reactions involving such galvanic couples, the cathode becomes passivated, while the anodic member reacts vigorously due to the electro- chemical reaction which occurs (Hiskey and Wads- worth, 1975). Serry, eta1 (1978) observed that when chalcopyrite and pyrite were in intimate contact in natural ores, the chalcopyrite reacted vigorously by galvanic conversion as a result of the higher rest potential (~ 0.63 V) as compared to the chalcopyrite (~ 0.53 V). In addition, it was postulated that because of the elemental sulfur which can form on the anodic chalcopyrite in this galvanic conversion process, reactions in acid-bacterial medium would be expected to have accelerated copper extraction because of the conversion of any sulfur product layer on the chalcopyrite anode to sulfuric acid according to the following general reactions: [MS?M2+ + S° + 2e- (1) and 2S° + 302 + 2H20 bacteria?-2H2SO 4 (2)] where M in reaction (1) designates the metal (or metals in the specific case of chalcopyrite) to be released to solution by galvanic conversion.

Jan 1, 1982

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By John R. Twining, Michael D. Lawton, Ross A. Jeffree

The Finniss River system in tropical northern Australia has received 'acid-drainage' contaminants from the Rum Jungle uranium/copper mine site over the past 4 decades. Following mine-site remediation that began in 1981-82 the annual contaminant loads of sulfate, Cu, Zn and Mn have declined by factors of 3, 7, 5 and 4, respectively over 1990-93, compared to the 1969-74 pre-remediation loads. Comparison of the frequency distributions of contaminant water concentrations over these pre- and post-remedial periods have shown varying degrees of reduction in the highest levels following mine-site remediation, that are consistent with reductions in their annual-cycle loads. Among the three selected major metal contaminants the reductions in maximum water concentrations are most pronounced for Cu. The demonstrated reductions in the highest water concentrations of all four contaminants are also associated with previously reported ecological improvement in the Finniss River system, compared to the benchmark of environmental detriment established in 1973fl4, prior to the beginning of remediation at the mine site.

Jan 1, 2000

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By Jacob Mathis, Mark Bradford, Alston Noronha, R. M. True

In June 2022, Louisville MSD completed a 6.5-km (4.0-mi), 6.1-m (20-ft.) diameter CSO conveyance and storage tunnel system located along the Ohio River in downtown Louisville, Kentucky. For large diameter shaft and tunnel construction, drill-and-blast operations among other methodologies were used in close proximity to federal, commercial, and residential properties with no impact to stakeholder infrastructure. s one of the rst maor tunneling proects in Louisvilles metropolitan area, this paper explores Black & Veatchs rigorous geotechnical instrumentation monitoring program that provided uality assurance for local stakeholders and afrmed innovative tunneling solutions can be successfully executed in an urban setting.

Jun 23, 2024

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By Donna L. Boreck

Introduction Coal has been mined in the western United States since the mid-1800s. The resource is abundant in the West. Despite recent economic conditions, it remains an important part of the nation's energy warehouse. Many of the seams that comprise the western resource base are thick, some exceeding 61 m (200 ft). Multiple, closely-spaced seams or thick coals that split into two or more minable seams are also common. Historically, subsurface development recovered from less than 15% to 50% of these deposits (Matson and White, 1975). This resulted in a substantial loss of inplace reserve due to the limited height that could be mined using the available technology. In an effort to increase future recovery from such deposits, the US Bureau of Mines analyzed the potential for incorporating three thick-seam mining methods into western coal mines. These methods are high-face longwall, multislice longwall, and longwall caving. They were developed in Europe and are being used to mine thick coal seams in Europe and Asia. One aspect that will determine their success in the US is the geology of the individual deposit; namely, are the methods adaptable to the geologic conditions characteristic of western coal? This paper analyzes some of the geologic factors that would affect development of thick or closely-spaced seams using these mining methods. Occurrence of thick and closely-spaced seams Since mining conditions and methods differ around the world, a thick seam is often defined as a seam whose total thickness cannot be extracted using the available equipment. In the western US, the maximum extractable mining height is about 4.3 m (14 ft). For this research, a thick seam was defined as a minable seam 4.6 m (15 ft) thick or more. Since one of the seams is usually lost using standard mining methods, closely-spaced or split seams were also addressed. These were defined as two minable seams 1.5 m (5 ft) thick or more separated by 9 m (30 ft) of interburden. Thick or closely-spaced coal seams are common in the West. Their importance has not been documented due, in part, to the methods used to measure resources. In the past, all reserves greater than 1.1 m (42 in.) thick for bituminous seams and greater than 3 m (10 ft) thick for subbituminous seams were grouped together and were differentiated only by rank. Further differentiation by seam thickness or minability was not done. For this reason, reserve figures for thick or split seams are difficult to determine. By analyzing available published resource data, Ferm and Muthig (1982) addressed thick seam resources. They estimated a resource of 90 Gt (99 billion st) of coal (16% of the Western resource base) in seams 4.6 (15 ft) or greater at less than 610 m (2000 ft) overburden. Yet, a later study of Pierce and others (1982) on one thick seam deposit in the Powder River Basin estimated a resource of 103 Gt (113 billion st). Pierce (1986) reported that the overburden reached a maximum of 731 m (2400 ft). The resources in this single deposit exceeded the 90 Gt (99 billion st) total projected for the entire western US by 12.7 Gt (14 billion st). Due to such differences, this author chose to look at reported occurrences of thick or closely-spaced minable seams in place of resource figures, to verify the need to research thick seam mining in the West. An occurrence was defined as an isolated site where a thick seam or two or more closely-spaced seams were reported. The occurrences were derived from published material - mostly mine descriptions, measured sections, coal exploration logs, and oil and gas logs. Due to time constraints, the reserves associated with each occurrence were not determined. All data points were random. The analysis was limited to occurrences in Colorado, Wyoming, and Utah. Although source material available to the author was limited to general coal summa-

Jan 3, 1988

By A. D. Davis

The Gilt Edge Superfund Site is a former heap-leach gold mine that currently is being remediated in the Black Hills of South Dakota. Mine runoff water is treated before release from the site. The field pH, before treatment, is about 3, and the water contains arsenic and some heavy metals, in addition to sulfate concentrations of about 1400 to 1500 mg/L. In the Keystone area of the Black Hills, naturally occurring arsenic has been detected in ground-water samples from wells. Keystone City Well #4, which is not used currently, showed arsenic concentrations of 36 parts per billion (ppb) and sulfate concentrations of about 19 mg/L. With field samples of water from these sites, a limestone-based method was successful in reducing arsenic and heavy metals concentrations. The results are significant because previous research with the limestone-based method mainly had involved samples prepared with distilled water in the laboratory, in which interference of other ions such as sulfate did not occur. The research indicates the potential for broader field applications of the limestone-based removal method.

Jan 1, 2011

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By Masaji Kato, Yuusaku Tominaga

To maintain good condition of ventilation for both safety and economy, many regulators are installed in a network. In case the open state of a regulator is different from the set point, identification of a broken regulator and a countermeasure to recover airflow distribution in a network must be initiated as soon as possible. An experienced mining engineer can sense a deviation from ordinary airflow quantity. In this paper, a new system to monitor all the regulators in a network is introduced. The basic concept of the system is utilization of both human sensing of airflow rate and computer simulation to understand the macroscopic characteristics of a ventilation network. A fuzzy pattern distinction method is used to process human determination of airflow rate that may be ambiguous. The applicability of the system is demonstrated using the ventilation network of the Horonai coal mine, Japan. In particular, it is shown that the system can identify the regulator to be repaired from information supplied by workers relating to air- flow in a few sensor branches.

Jan 1, 1997

By Rajendra K. Devala, Sukumar Bandopadhyay

In order to be able to design an adequate mine ventilation system it is necessary to understand how pollutant masses disperse into turbulent ventilation air streams. The mixing of gases and dusts with ventilating air, and dispersion of these pollutants in mine airways, are important flow or transfer problems. For the solution of such problems, the finite difference technique is often used. In this paper, numerical approximation schemes for the solution of the mass transfer problem have been developed using several explicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments using the concept of Root Mean Square error. The comparison of various schemes reveals that the explicit finite difference schemes analyzed here give more accurate results at lower velocities, though the results are dependent on the spatial and time steps considered. At higher velocities the schemes tends to oscillate about the analytical solution. INTRODUCTION In mining, most of the mine air pollutants, such as respirable dust, methane, blasting fumes and diesel exhaust, are produced at the mine face and in haulageways. Injection of any of these pollutants in the mine ventilating air causes disturbances of the equilibrium state of the pollutant concentration of the ventilating air. The mixing of these gases and dusts with the ventilating air are typical examples of mass transfer processes. Pollutants are diluted by the stream of ventilating air flow along airways and discharged into the outside atmosphere of the mine through a return shaft. The dispersions of these pollutants in mine airways are important flow or transfer problems. Knowledge about pollutant sources, emission and transport of these pollutants are essential for ventilation planning and design to ensure good engineering control over air quality, quantity, and environmental conditions. Modeling of mass transfer phenomena in mine ventilation is largely based on extensive studies of turbulent dispersion in wind tunnels and the lower atmosphere of the earth. The general approach in the formulation of models lies in the recognition that these mass transfer phenomena can be conceptualized as a flow problem that can be solved by the general application of Taylor's theory (1954) of turbulent flow and diffusion with modification appropriate static and dynamic parameters. If the face zone is initially contaminated by a pollutant over a long section (e.g. instantaneous exposure of large gas accumulation, rapid methane release etc.), the process of decontaminating the mine workings can be regarded as displacement and diffusion of the tailing edge of the cloud of contaminates in the form of a semi-infinite gas body, for which a one-dimensional mass transfer equation is represented by: [at + u • ax = Ex ex2 + f (x,t)(1.1)] In Eq. (1.1), the term [~~] is the rate of growth of the concentration in the differential element, while a [(5xx )] is the net gain of material due to convective transfer. The two terms balance the total loss of material due to turbulent dispersion that is represented by [Ex . 21] and f(x,t), the source term for the pollutant in the roadway. Several cases of mass transfer that occur in mining can be identified and modelled using the conservative volume element method. The governing equation, along with the associated boundary and initial conditions, source terms and their solutions are detailed elsewhere (Bandopadhyay and Ramani, 1988, Devala, 1989). Only one mass transfer situation is presented (Figure 1) here for the present analysis. Mixed Evolution of Pollutant (multiple pulses) Typical examples of these situations are emission of pollutants from multiple diesel vehicles in the face area, and gas emission from standing pillars as well as from broken coal seam during coal cutting with a continuous miner. The mathematical statement of the problem along with the initial and boundary conditions are given below, Governing Equation: [do+u- =E d2c(1.2) ataxx dx2] Initial conditions:

Jan 1, 1993

By C. RAMADINI, F. NURJAMAN, A. SHOFI, B. SUHARNO

Nickel demand is increasing along with the rising need for stainless steel and other alloy steel/iron. The small addition of nickel in such materials can improve impact strength, ductility and corrosion resistance. Nickel is generally obtained from nickel sulfide ores (nickel associated with sulfur) and nickel laterite ores (nickel associated with iron and magnesium silicate). Almost 60 percent of nickel is now produced from sulfide ores, despite its existence in sulfide ores being less than in laterite ores. However, the depletion of sulfide ore reserves makes the mastery of nickel laterite ore processing of important and immediate concern. Selective reduction followed by magnetic separation has been in development in lateritic nickel ore processing to overcome the issues of high energy consumption and pollution associated with conventional pyrometallurgy methods such as blast furnace and rotary kiln electric arc furnace (RKEF).

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dozer operators are frequently exposed to whole-body vibration (WBV) during the execution of their work. Occupational exposure to WBV in Indian surface coal mines was evaluated by measuring vibration intensity and duration of exposure. A triaxial accelerometer was placed on the operator seat surface for taking the readings. Based on frequency-weighted root mean square acceleration equivalent to 8-hr shift duration, i.e., (A(8)) all dozer operators have exceeded an Exposure Action Value (EAV) of 0.5 m/s2 , and 90% of dozers did not exceed Exposure Limit Value (ELV) of 1.15 m/s2 . Based on Vibration Dose Value (VDV (8)), all dozer operators have exceeded Exposure Limit Value (EAV) of 9.1 m/s1.75, but no dozer operators have exceeded Exposure Limit Value (ELV) of 21 m/s1.75. Further, an epidemiological study was performed for identifying the extent of musculoskeletal disorders (MSDs) among dozer operators. For the detailed study, 42 dozer operators and 22 controls were selected from 2 surface coal mines. The control group was not exposed to WBV. It was seen from the cross-sectional study that pain in the lower back was predominantly higher (83.33%) in the exposed group when compared with the control group (31.81%). Likewise, pain in the neck (47.61%), shoulder (42.85%), knees (42.85%), and ankle (11.90%) was higher in the exposed group than that of the control group (22.71%, 0%, 45.45%, and 4.54%). A significant observation among the exposed group was that there was degradation in the quality of life. The outcome of the study would assist in monitoring and mitigation of machinery-induced vibration diseases (MIVD) in India and generally applicable to most of the mechanized mines as well. However, comprehensive studies are still needed to enunciate the magnitude extent.

By R. S. C. Rogers

The present study examines the use of two vs. one stage of hydrocyclones in a pilot scale ball mill circuit. The approach used for doing this is based on computer simulation with mathematical models that explicitly account for the grinding mill/classification system interaction. Parameters for the ball mill model are obtained using a short-lived radioactive tracer method in open circuit tests of the study mill. The hydrocyclone model, based on the size selectivity concept, is developed and validated in standalone testing of the study hydrocyclones. Simulation procedures are validated through actual tests of the closed circuit grinding configurations of interest. Results of the evaluation indicate that two stages of hydrocyclones in the study circuit would improve classification, increase productivity and lead to more closely sized circuit products when compared to the conventional one stage hydrocyclone circuit. A computer simulation approach for comparing these circuit configurations in larger scale grinding circuits is also suggested.

Jan 1, 1981

By Kanaya Koichiro

Doyashiki Concentrator in Hanaoka mine of Dowa Mining Co., Ltd. started the operation in 1943, treating the ore mainly from Doyashiki ore deposits. After the cessation of mining of Doyashiki ore body in 1973, Doyashiki concentrator began to treat the ore from Fukazawa mine instead in the same year, and furthermore the ore from Ezuri mine In 1979. Currently Doyashiki concentrator treats 30,000 tons of ore per month from both mines. The ore treated is complex sulfide ore, called "Kuroko" (black ore), and the principal minerals contained in the ore are chalcopyrite, galena, sphalerite, pyrite, and barite, accompanied by bornite, tetrahedrite, tennantite, covellite, stromeyerite, argentite, polybasite, pearcite, and electrum. The Principal gangue minerals are quartz, gypsum and clay. The grade of the feed to the concentrator averages 0.9 p/t Au, 110 g/t Ag, 1.1 %Cu, 2.8 %Pb, 9.2 %Zn, 5.0 % Pyrite-S and 13% BaS04. The feed is, after washing and two-stage crushing, ground to 88% minus 200 mesh in a rod mill and ball mills with cyclone classifiers, and five concentrates are recovered by flotation. Primarily copper-lead bulk concentrate is recovered by sulfurous acid-lime flotation method, and then from the bulk concentrate copper concentrate is floated by hot pulp flotation method, sinks being lead concentrate. Zinc concentrate is recovered from the tailing of copper-lead bulk flotation, pyrite concentrate from zinc flotation tailing and barite concentrate from pyrite flotation tailing. The final tailing is sent to the dam.

Jan 1, 1982

By Georgi N. Shoushoulov, Ventsislav D. Bozhilov

The mining conditions in the Meden Rid mine at levels below 1000 m from the Earth's surface are specific and rather severe. The rock temperature is about 40-45°C. The air humidity in the workings is approx. 80-90%. There is a limited capacity for additional fresh air supply. The air supply and distribution systems in the mine are very complicated. The airflow recirculation is due to the existing arrangement of the main fans. Certain accidental phenomena are difficult to predict. All these conditions create possibilities for heat and mass exchange between the rock and the air current thus hampering the control of the ventilation and air-conditioning in the mine workings. The changes in the temperature and humidity in certain characteristic places of the development and extraction workings are predicted. The refrigeration output required and the arrangement of the air coolers are also determined. A new ventilation and air- conditioning scherne has been developed. The new ventilation- cooling designs for levels between 1000-1200 m beneath the Earth's surface are based on the use of portable refrigerating machines having low water flowrate as well as heat-insulating and waterproof materials and methods for preliminary cooling of the orebody within the mining block.

Jan 1, 1997

By Ruipeng Qian, Pengfei Wang, Guorui Feng, XianJie Du, Jun Guo, Yuxia Guo, Tingye Qi, JinWen Bai

"A numerical modeling was conducted to describe the behavior of overlying strata on the longwall top coal caving face for exploitation of a 16.8 m thick coal seam. Three typical structural models, including the Cantilever Structure (CS), Lower Cantilever and Upper Hinged Arch Structure (LC&UHA), and Lower Arch and Upper Voussoir Beam (LA&UVB), were developed. Based on mechanical analysis of the different structures of the key strata, and considering the behaviors of the broken igneous rock strata, a method was proposed and applied to estimate the structures of the overburden strata. The results had been verified by a field micro-seismic monitoring test. The paper provides a foundational method to determine the shield loadings for the top coal caving longwall face.INTRODUCTIONLongwall top coal caving (LTCC) is a highly productive underground mining technology which has been widely applied to the exploitation of the thick coal seams in China and other countries due to its high efficiency (Ju and Xu, 2013; Ju, Xu, and Wang, 2011; Liu et al., 2009). In recent years, a large amount of research on mining pressure forecast, strata control, and mechanical equipment improvement of the LTCC technology has been carried out, which greatly advances the field application of the technology (Liu et al., 2009; Yu, 2016; Dou et al., 2014; Feng et al., 2011; Chen and Li, 2011; Yin, Yan, and An, 2008). In 2006, the LTCC technology was first applied to the exploitation in a 20 m thick coal seam at the Tashan Coal Mine in China (Yan et al., 2011). Ten years of mining at the Tashan Coal Mine has highlighted the importance of the support management in controlling the roof strata on the extra-thick LTCC face. The mining pressure is closely related to the structural features of the overlying strata and its movement laws (Yu, 2016; Dou et al., 2014; Feng et al., 2011). However, the distributions of three zones—caving zone, fracture zone, and deformation zone—on the fully mechanized caving longwalls changed significantly with the increase in thickness of the coal seam (Chen and Li, 2011). The behavior changes of the roof strata led to abnormal pressure in the mining face and resulted in the difficulty of surrounding rock control (Yin, Yan, and An, 2008; Liu et al., 2009; Yan et al., 2011; Gong and Jin, 2008). Therefore, the theoretical research focused on the behavior of overlying strata to reveal the laws of mining pressure has important theoretical significance and practical value.Many classical studies (Qian and Shi, 2003; Feng, 2010; Yu, 2015; Yu, Yan, and Liu, 2012) had been done to describe the behavior of overlying strata in the mining process. It has also been reported that magma intrusion causes an important effect on the surrounding rock, coal, and methane (Wang et al., 2005; Liu et al., 2007). On the one hand, the property and structure of the coal seam was obviously changed by the magma intrusion and resulted in a potential danger of a gas outburst during the mining process (Chen et al., 2012; Wang et al., 2014). On the other hand, the hard igneous strata and the joints occurred with the magma cooled, causing an abnormal behavior of overlying strata and resulting in a series of dynamic disasters during mining (Xuan, Xu, and Lu, 2014; Lu et al., 2016). In fact, many coal fields in China are intruded by igneous sill, including the Datong, Shuozhou, Huainan, and Xuzhou coal fields (Chen et al., 2014; Wu, 2011). The 3–5 coal seam at Tashan Coal Mine in Datong coal field is very thick and is intruded by a large area of layered lamprophyre rock. Face falls and shield failures occurred frequently during the face retreat."

Jan 1, 2019