Search Documents

By W. R. Reed

This study evaluates the roof-bolter canopy air curtain (CAC) system in an exhausting face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. Two scenarios are considered: (1) a roof-bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof-bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment that contains 6.0 mg/m3 of respirable dust and is ventilated by an exhaust curtain with 9,000 cfm (4.25 m3/s) of air to simulate the roof-bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8 percent. When the roof bolter is operated close to the face, increasing CAC airflow was required for adequate protection, as the dust reductions can be as low as 39.5 percent. Increasing CAC airflows to 350 cfm (0.17 m3/s) and 450 cfm (0.21 m3/s) were evaluated, demonstrating that dust reductions increased to 59.7 percent (350 cfm) and 72.0 percent (450 cfm). These results revealed improvement in respirable dust reductions compared to the CAC airflows at 250 cfm when the bolter is operated close to the face, showing the CAC can provide protection against high respirable dust concentrations for roof-bolter operators.

By SAHENDRA SINGH, SANJIT KUMAR PAL, DHARMITA HORO

This study was carried out in Ichadih to map the sulfide/gold mineralization using combined electrical resistivity tomography (ERT) and self-potential (SP) methods. No geophysical analysis has been carried out to delineate such ore deposits in the area. Thus, the study provides a different approach for approximate location and extension of the quartz reef associated with sulfide/gold mineralization. It also provides the elementary idea for further detailed subsurface investigation in terms of geological and geophysical approach. 

By V. Kontogianni

The underground extraction of coal is associated with ground movements extending from the mining area to the ground surface, which result in bowls of ground subsidence, with amplitude exceeding the amount of several meters and occasionally with important tilt and curvature of ground surface. Such changes at both the underground environment and surface topography lead to destruction of buildings, failure of utilities and transportation networks, and occasionally formation of areas vulnerable to flooding, or even small pools. Based on geodetic surface measurements of ground elevation changes, various theories and empirical models relating surface subsidence with the geometry of underground voids formed have been proposed, and predictions of expected subsidence in the form of contours have been estimated. In this study a case study of planning of a new highway network through areas in which coal extraction was also planned is discussed. This work is partly funded by EU. The optimum solution selected was a modification of the initial highway planning, so that the road is increased in length and by-passes the richest coal-field, where maximum post-exploitation subsidence was predicted, and only crosses either minor coalfields, which are not to be exploited, or even margins of main coalfields, in which minor post-exploitation subsidence is expected.

Jan 1, 2006

By William P. Diamond

Production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 m' to 10.1 x 106 m3. Peak production rates were generally about 0.03 to 0.06 x 106 &/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to several factors including: completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance, is hole location. Holes on the ends of the panels, where overburden strata are in tension due to the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location which is in compression. Analysis of gob gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1995

By J. M. Hollow, D. E. Walsh, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Carbon fines are collected by a filter press because of their gold value. Samples of the carbon fines show that they consist of 20-30% carbon, 70-80% grit and 0.17-0.68 kg/t (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in a form of recrystallized free gold grains, with the balance being adsorbed gold on the carbon. High recoveries of gold and carbon were obtained in laboratory tests using froth flotation, with a high rejection of the grit.

Jan 1, 2001

By J. S. Walker

Public Law 95-87 enacted by Congress in 1977 and subsequent regulations require coal mine operators to predict the effects of mining on the environment prior to the start of mining. Prediction of the effects of mining on the local groundwater system is a difficult task due to its complex nature and the lack of detailed published information. An investigation of water level fluctuations in five we1 1s positioned over three consecutively mined longwall panels was initiated in conjunction with an intensive subsidence monitoring program. The purpose of this work was to provide detailed information which could be used to predict certain hydrologic effects of longwall mining in the Northern Appalachian Coal Region. The results of this case study indicate that water level fluct- uations in the local ground-water system above longwall panels is associated with subsidence and that the static water level will generally re- establish at or near the pre-mining elevation after mining is completed.

Jan 1, 1986

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

Anhydrite-based dam constructions, which have been implemented successfully in other geological formations, were investigated with regard to their suitability in salt mines. The laboratory investigations show that anhydrite-based building materials with suitable additives bind safely in spite of the high temperatures in salt mines which normally pre-vent hydration. The dependence of the compressive strength, swelling behavior, porosity and permeability upon the choice and ratio of binding material components and additives was determined. Based on the results of these investigations, a pilot-scale experiment was carried out at the GSF Research Mine Asse (Germany) using a mixture suitable for the prevailing conditions

Jan 1, 2004

By Ora H. Rostad

Some gold production was obtained from placer deposits in Puerto Rico during the period of Spanish colonial rule, but most of the gold was produced prior to 1536. There had been no significant hard rock mining, other than in quarries for road metal or construction purposes or for raw materials to make cement, prior to 1954 when the government of the Commonwealth of Puerto Rico recognized that changes in the mining code were necessary to stimulate exploration for metalliferous ore deposits. The Puerto Rican Legislature passed an act (No. 6), which was approved on Oct. 6, 1954, that reiterated that the title to all "commercial minerals" is vested in the Commonwealth of Puerto Rico. The act provided for the establishment of a Mining Commission, stipulated the power% with which the Mining Commission was vested, and provided that no one may dispose of "commercial minerals" in Puerto Rico without a Commonwealth grant issued on its behalf by the Mining Commission. Act No. 6 also provided for prospecting permits, mining leases, and grants. The Mining Commission, by authority granted to it by Act No. 6, adopted regulations effective Nov. 21, 1957, relating to prospecting, leasing, and producing commercial minerals in Puerto Rico. Royalty rates were also specified for various types of deposits at different annual tonnage production levels.

Jan 1, 1991

By Vincent Castronova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

A group of bisbenzylisoquinoline (BBIQ) alkaloids has been shown to exhibit various degrees of effectiveness in preventing silicainduced fibrosis in animal models (1, 2). The capability of these drugs to interact with phosphatidycholine vesicles and rat alveolar macrophages was studied using fluorometric and equilibrium dialysis methods. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, the chiral configurations, and the double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is highly effective in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In summary, this study indicates that alveolar macrophages exhibit large binding capacities for certain members of the BBIQ alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds, suggesting that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.

Jan 1, 1991

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By A. G. Fabbri

This paper aims at the application of quantitative criteria for evaluating the mineral potential of square cells representing areas in terrains being explored at a reconnaissance level. The assumption is made here that the evaluation methods used by an expert economic geologist can be organized into geological models for establishing associations within imaged areas, that correspond to pixels with similar characteristics. UTM-registered multiple data sets have been constructed which include seasonal LANDSAT 2 and 4 images, SEASAT scenes, selected airborne radar images, digitized aeromagnetic, gravity, bedrock geology and topographic elevation maps. The area of interest is located in the Bathurst Inlet, District of MacKenzie, N.W.T., where a preliminary mineral potential evaluation was performed by the Geological Survey of Canada to assess its suitability for a national park. The multiple data sets described in this paper can be used for many studies at different resolutions, for comparing processing methods in remote sensing and, most importantly, for evaluating the physical and spatial relationships between the different images in registered data sets.

Jan 1, 1989

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

In this work, a new flotation strategy was proposed for the flotation of rutile. In this strategy, rutile was activated by Pb(NO3)2 and then floated with amyl xanthate (AX) as a collector at pH 8. Pb(OH)+ was the dominant lead species in the solution at pH 8 and is believed to be the major species reacting with the rutile surface. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) study revealed that the lead activation products were well distributed on the rutile surface, and AX− could further bind with the Pb atom on the Pb-activated rutile surface. In this regard, the Pb-activated rutile could be floated by AX. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis indicated that Pb(OH)2 was generated on the Pb-activated rutile surface. The electron transfer during the adsorption of the AX− on the Pb-activated rutile surface was also investigated by XPS analysis.

By J. A. Botín

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require of more complex risk evaluation models, that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, production rates, among many other). In this context, Real Option Valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed, which successfully quantifies the risk associated to dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mining Project.

Feb 27, 2013

In general, it cannot be assumed that the strength of coal pillars remains constant over long periods of time. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing the load-bearing capacity of the pillars. This paper discusses a unique approach to determining the time-dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15, and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar, and the strength profiles were determined for each hole using a borehole penetrometer. The strength data were treated statistically to establish time-dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 2012

By Yuqi Zhao, Zhiyong Lin, Leiting Shen, Hongyang Wang

Gibbsite-type bauxite is the main material for alumina extraction by Bayer process globally, while the iron in red mud is difficult to use for the high alumina content. Therefore, the efficient separation of iron and alumina is the premise for the resource utilization of red mud. In this work, the separation of iron and alumina in red mud containing 47.45% Fe and 11.58% Al2O3 was studied through reduction roasting followed by magnetic separation. The analysis methods of XRD, VSM, SEM, and EDS were used to investigate the phase transformation of red mud during reduction roasting. Results show that hematite can be firstly reduced into magnetite, and alumogoethite into magnetite and alumina. Then, the magnetite reduction undergoes the process of Fe3O4→FeO→Fe, while alumina can react with FeO to form hercynite. The hercynite is ultimately reduced into metallic iron and alumina at elevated temperature. The specific saturation magnetization of reduced product is closely related to its main minerals, that is, the specific saturation magnetization of magnetite and metallic iron is higher than that of wustite and hercynite. The mass ratio of Fe to Al2O3 in magnetic concentrate increases with roasting temperature, from 4.55 at 600 °C to 10.27 at 1200 °C. Therefore, efficient separation of iron and alumina in red mud could be achieved through deep reduction-magnetic separation.

May 2, 2024

By R. C. Ford

The advent of solvent extraction-electrowinning (SX-EW) technology for recovery of copper from low grade oxide ores has extended the operational lives of many historic mines in the western United States, and made many other orebodies economically viable worldwide. Many of these operations are mature and face closure within the next decade, depending on market conditions. Closure of a large copper heap leach operation has not been undertaken, and differs in some important chemical respects from closure of gold leach pads. Challenges for closure include prediction of solution chemistry and draindown characteristics, determining the benefit of cover placement in semi-arid climates and evaluation of solution management strategies once the economics of copper recovery are no longer favorable. This paper discusses issues pertinent to copper heap closure in semi-arid and arid climates, and strategies for their management.

Jan 1, 2000

By Simón Díaz‑Quezada, Ernesto Arancibia, HUMBERTO ESTAY, Tomás Vargas

In situ leaching (ISL) is an attractive technique that enables copper recovery from copper oxide ores that are either low-grade or located at depths too great to be economically exploited through conventional methods. At present, in situ leaching (ISL) has been applied to intact copper oxide ores, in particular, those which (i) present a good natural permeability and (ii) do not require preconditioning. Many copper oxide ores present low natural permeability. These are located above the water table and need preconditioning for the ISL application. The present work shows an economic assessment of the application of ISL to this type of copper ores. The preconditioning technique considered here involves the application of partial mining by sublevel stoping by removing a small fraction of the ore. This technique results in forming an ore bed with good permeability and good solution collection at the stope base. The economic assessment of this approach suggests that it can be implemented with positive net present values to copper oxide ores located at depths in the 100–300 m range, with copper grades above 0.4%. The maximum acid consumption values are below 52.5 kg/t, with blasting procedures designed to produce an ore bed with an average particle size below 6″. The breakdown of operational costs indicates that the mining cost is still very high, accounting for up to 60% of the total operating costs. Therefore, optimizing mining procedures is still necessary for improving the economic outlook of this approach and thus expanding the application field of ISL.

Feb 4, 2023