Search Documents

By J. Potter, A. Anani, C. Antonio

This research aims to test the hypothesis that the low retention rate of women in the mining industry is caused by workplace culture and policies established due to gender segregation. A quasi-experiment is developed to determine the cause-and-effect relationship between gender segregation-inspired culture and the retention of women. The experiment considers the impact of the job type and the operational environment. The analysis provides information on factors that cause low retention of women in the industry, the extent to which gender segregation plays a role, and insights that allow actionable and measurable changes in the industry.

Feb 1, 2023

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024

By Karoly C. Kocsis, Kyle A. Scalise, Marcelo Bandeira Teixeira

Understanding the effects of various ventilation and climatic parameters on the work conditions and comfort in underground mines is critical for efficient ventilation system design and cost savings and to ensure the health and safety of mine workers. To understand the effects that the thermal damping effect (TDE) and the thermal flywheel effect (TFE) have on the ventilation system design and potential cooling system, this paper compares and analyzes the wet and dry-bulb temperatures at the bottom of an intake shaft using two modeling software packages, Ventsim™ and Climsim™. The comparison shows the consequences and importance of taking into account the TDE/TFE when predicting the climatic conditions in future underground mines, especially when deciding on whether a cooling system should be employed in order to provide adequate climatic conditions in the production stopes, dead-end development headings, and throughout the mine. Ventsim™is able to account for the TFE, while Climsim™does not. Both software packages have their uses and are used within the mining industry, but it is useful to understand their limitations and where the future of underground climatic modeling will lead.

Oct 9, 2020

By Mahmud Esad Uluer, Aaron Noble

Respirable coal mine dust (RCMD) is one of the biggest occupational health hazards for underground coal miners. Coal extraction is a main source of RCMD. To prevent challenges related to RCMD from developing, it is vitally important to limit airborne RCMD and stay within the regulatory limitations for mine operators. The flooded-bed dust scrubber (FBS), mounted on a continuous miner, is one of the most widely used dust mitigation technologies in room-and-pillar mining, but it is limited by technical challenges, the most notably being the potential to clog. In this study, the impact of mesh design and surface modification on system efficiency is examined using different vibrating, liquid-coated, stainlesssteel mesh panels in a laboratory-scale FBS.

Sep 1, 2024

By S. A. Allison, N. P. Finkelstein

After a brief consideration of the properties of zinc sulfide minerals, their flotation characteristics, and their reactions with thiol collectors, the literature on the activation of the minerals by cupric ion, their deactivation by cyanide, and their depression is reviewed in detail. The distinction between deactivation and depression is stressed. The contradictions in the published results and theories are discussed and attempts are made to resolve them. It is concluded that, whereas all aspects of the subject require further investigation, the study of depression is most likely to yield benefits in practice.

Jan 1, 1976

By Hervé Le Bissonnais, Jean-Pierre Janin, Anne Bergère, Pierre Renier

"The most important impact on the environment of a tunnel excavation is the creation of surface settlements. Nowadays, the mechanized tunneling allows minimizing the settlements, applying a confinement pressure which counterbalances the ground de-confinement. It is thus essential to determine the correct amount of confinement pressure. In this paper, the authors present a 3D numerical study simulating the EPB-TBM excavation of a water tunnel, in the Flanders clays (north of France). Firstly, a simplified 3D simulation, based on the concept of instantaneous longitudinal settlement curve, was performed to predict the surface settlements for different values of heading confinement pressures. Secondly, the same pressures were tested by the EPB-TBM in a monitoring zone. The comparison between the prediction settlements and the measurements was very satisfactory and allowed validation of the numerical approach and the choice of the optimal confinement pressure value for a sensitive area of the project. INTRODUCTION The excavation of a tunnel can create displacements of the surrounding soil which may affect existing structures and generate unacceptable dysfunction. The development of the closed shield tunneling has permitted to reduce the volume loss generated around the excavation and consequently the surface settlements. In this case, as explained by different authors (Clough et al., 1985; Kastner et al., 1996; Mair and Taylor, 1997), the ground movements are influenced by the TBM works: the heading confinement pressure, the shield overcutting and conicity, the annular void grout injection parameters, the segment concrete lining rigidity, the consolidation of the grout. Hence, in the tunnel design, it is important to take into consideration these different processes of the excavation works to simulate correctly the tunneling process."

Jan 1, 2016

By M. Hancer

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCI. Precipitation of the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999

By Devin Burns, Saima Ghazal, Michael Owusu-Tweneboah, Kwame Awuah-Offei

Trust in AI systems and the nature and amount of information about the system can influence decision-making. It is, therefore, crucial to understand how AI-powered monitoring systems (e.g., gas monitoring systems) influence miners’ trust and decision-making in emergency evacuation. This work focused on measuring the differences between how participants respond to a simulated underground mine emergency evacuation situation when warnings are represented as coming from a human or AI-based monitoring system. We also manipulated the amount of information participants received about the system, yielding a 2×2 between-participants survey design. The participants received an alert message about rising gas levels in a mine and provided a response on how they would react and reported their perceived safety. We also asked questions to assess their trust in, preference for AI over human-based gas monitoring systems, and whether they are willing to delegate the duties of underground gas monitoring to AI systems. The experiment results show the amount of information had a significant influence on miners’ trust and decision-making. The safety perception of participants based on age, number of children and ethnicity was significantly different from one category to another. This work provides valuable insights as the mining industry deploys AI systems to aid mine safety.

Feb 1, 2025

By C. R. DeGennaro, Yongjun Zhang, J. Bickson, J. L. Carr, Chenming Zhou, J. R. Srednicki, B. Lambie, M. Girman, J. A. Galanko

Between 2005 and 2021, surface mining haul trucks were involved in 54 fatal incidents in the United States [1]. Collision warning and avoidance systems (CXS) can help haul truck operators navigate their route safely. The evaluation of CXS object detection performance for surface mining haul trucks relies on the positional accuracy of the ground truth instrument. As part of a holistic approach, researchers from the National Institute for Occupational Safety and Health (NIOSH) characterized the accuracy of a global navigation satellite system (GNSS) that serves as the ground truth instrument to determine object position and velocity in CXS object detection performance testing. We used precision surveying equipment to establish ground truth points for comparison with GNSS data collected for static positional measurements and reduced-scale straightline vehicle dynamic tests. We conducted these tests with real-time kinematics (RTK) and then satellite-based augmentation systems (SBAS). For the dynamic tests, we measured a distance error of 1.34 m (4.40 ft) using RTK and 1.50 m (4.92 ft) using an SBAS. This research will provide CXS manufacturers and CXS researchers a basis for evaluating the positional accuracy of CXS. Note that we did not evaluate any CXS in this experiment.

Feb 1, 2024

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By O. Konovalov, M. Zhuravkov

In report the results of performance of research works on building up of the connected geoecological and geomechanical monitoring system for modelling and study of a state of mining massif in a region with large-scale underground mining works are discussed. The connected geoecological monitoring requires radical change of methodology of carried out works. To carry out modelling and researches it is impossible without construction of the integrated connected information model of region. Basis of construction of information systems and databases for all sections of Earth Sciences is the set of the approaches, among which, for example, methods of remote sounding, GIS- and GPS-technology etc. Computer technologies are basis on the "supercomputer" technology. The results of performance of some researches for regions of excavation of deposits of potash salts in Russia and Belarus are presented.

Jan 1, 2005

By J. Twining, V. Nguyen, J. Perera

A computer code for ecological risk assessment (ERA), AQUARISK, has been developed and applied to evaluate the likelihood of biotic detriment due to exposure to acid rock drainage (ARD) from the Burkunga mine site in Australia Stream water quality monitoring data were used for the assessment and were compared with a) national water quality guidelines, b) literature derived ecotoxicology data and c) biological monitoring data. With bioavailability calculations, the code predicted that, for metals exceeding the guidelines, 44% of macroinvertebrate species above the mine and 100% below the mine would be adversely affected by the metals in the stream. This compares reasonably and conservatively with biological monitoring that showed observed reductions of 41% and 85% of species respectively at each site. Using literature data for macroinvertebrates to predict impact produced similar estimates to using data for all taxa. Use of speciation modeling also lessened the degree of reduction in the median water metal concentrations required to achieve acceptable impact (measured either by exceedence of criteria or by species likely to be affected) by a factor of 75%. This result implies significant economic and management benefits in relation to remedial engineering or water treatment options for sites.

Jan 1, 2000

By E. M. Cukrowska

The evaporative pan complex consists of two adjacent seasonal pans. These pans carry an exceptionally high salt (TDS) load due to over 50 years of effluent discharge via the pipeline from mines. The nutrient, heavy metal, radionuclide load in the water and sediments of the pans are very high affecting groundwater around the pans. The groundwater in the region contains TDS > 40 000 mgl-1 and sulphates > 7000 mgl-1, whereas groundwater in areas assumed to be unpolluted by mining activities have TDS < 500 mgl-1 and sulphates < 200 mgl-1. The extent of continuity between the pans and the groundwater is unknown, although there appears to be seepage of contaminated groundwater into the river system.

Jan 1, 2006

By D. E. Walsh

With the exception of the development of large scale mining equipment (haul trucks, draglines, shovels, etc.), there are likely few other candidates responsible for the ability to exploit large tonnage, low grade deposits, than the development of large capacity comminution equipment and circuits; crushers and grinding mills. Ball mills are often the final step in the comminution process and are responsible for providing what should be the optimum particle size distribution of ore to subsequent mineral concentration steps in the flowsheet. Because comminution processes are such high cost centers for milling operations, both capital and operating costs, an enormous amount of research has been conducted to study and model their performance, in order to improve efficiencies (Kelsall, et al., 1969; Austin et al., 1984; Napier-Munn, et al., 1999; Powell and Smit, 2001). With respect to modeling ball mills, estimates of the breakage rates for individual size classes of ore particles are fundamental, as are the particle size class breakage functions (the progeny of particle sizes produced from breaking a coarser particle size class), also termed appearance functions. Fundamental research into particle breakage in tumbling mills focuses on how much energy is input into single particles versus how they break and what size distribution of particles results. Several test methods, including JKMRC?s well known dual pendulum test and drop weight test, have been developed for the breakage of coarse particles down to 6 mm in size (Napier-Munn, et al., 1999). Work on the breakage of finer particles is still an area of intense research and single particle breakage is being investigated as are multiple particle, fixed bed methods (Hoffler and Herbst, 1990; Bourgeois et al., 1992; Whiten, 2007).

Jan 1, 2011

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By H. P. van Ormer

The objective of this paper and the developed personal computer program is not to identify or try to identify the actual total drilling cost in any Rotary Drilled Blast Bole Program. The ideas put forth here and in the computer program developed are a very accurate way to measure what is often very hard to identify and interpret -The actual direct operating cost of various drilling package combinations including comparing with available blast hole sizes and patterns

Jan 1, 1988

By P. K. Gbor

Over 2 million tonnes of smelter slags containing Co, Ni and Cu are produced and stockpiled in Canada each year. Smelters also produce SO2 an air pollutant. Recycling these materials will maximize the value of natural resources and minimize possible environmental impacts of industrial operations. The objectives of this research were to understand the characteristics of slag, the reaction of slag with SO2(aq) and to develop a novel method for extracting Co, Ni and Cu from slag using SO2. The properties of slags from different smelters were studied, with emphases on the form of Co, Ni, Cu and Fe. Leaching experiments were carried out in a batch reactor. The parameters investigated included concentration of SO2(aq), stirring speed, particle size, temperature and pH. O2 was introduced into the reactor to study its effect on the system. The amount of each of Co, Ni and Cu in all the slags was less than 1%, while Fe was between 30% and 45%. The form of Co and Fe was primarily oxide, however, significant portions of Ni and Cu were present as sulphides. SO2(aq) alone, was effective in leaching Co and Fe. Cu dissolution was negligible due to precipitation. The presence of O2 improved Cu and Ni extraction. SO2(aq) was found to be more effective in leaching slag than H2SO4 at the same pH. The leaching process was modelled using the shrinking core model. A scheme was proposed for the extraction of Co, Ni and Cu from slag using SO2(aq). The process makes efficient use of SO2, separates Co and Cu at an early stage, and minimizes the consumption of base during Fe separation.

Jan 1, 2003

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022

By B. Suresh, Kalyan K. Das, Pradip

A series of salicylaldoxime derivatives with alkyl group substitution in the main chain and the side chain were synthesized and evaluated for the flotation of malachite, cerussite and smithsonite. The effect of chain length and the position of the substituent group on the selectivity of separation amongst oxidized copper, lead and zinc minerals are discussed in this paper.

Jan 1, 1995