Search Documents

By J. Parker

Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa (4000 and 7000 psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition

Jan 1, 1991

By Ray Brainard

The subsurface investigation for the Reach 4 Tunnel was expected to be completed in a single phase. This assumed that data from two nearby previous tunnels, combined with limited new subsurface information and surface mapping would be sufficient to characterize the rock behavior. Unforeseen rock conditions and complex faulting led to the recommendation for a second phase. This decision was not reached easily, as much of the follow-on work required helicopter support, and associated costs. The second phase of drilling found significantly more variability than the first phase and led to a very different and better understanding of the geologic and geotechnical conditions, and rock characterization.

By David Lynn Passmore

The reliability of mine operators reports to the Health and Safety Analysis Center of the U.S. Deparetment of Labor of days lost from work by injured miners is .267.

Jan 1, 1985

By Geoff Whebell, Dianne Coulthard

Sampling studies of high silver (+70%), gold dore led to the development of mine site sampling techniques and superintend­ing for the collection of samples for assay and bullion weights for settlement of shipped material. Data is presented which con­firms the reliability of the procedures against the traditional remelting and sampling at the refinery. The advantages to both mine and refiner are significant and are discussed.

Jan 1, 1998

By Brett Zernich, Michael Krulc, Brett Robinson

This paper provides an account of the efforts undertaken to construct the Northeast Interceptor Sewer (NEIS) project, which is a portion of a much larger program in Los Angeles, California to upgrade the city’s wastewater facilities. The project consisted of a number of elements, including both soft ground and rock slurry wall shafts, drilled shafts, soft ground EPBM mining, rock TBM mining, large diameter pipe placement, and underground structure construction. The need to complete the project under strict schedule constraints, in addition to the challenges of underground construction in congested urban areas, necessitated the work be undertaken with the proper balance of state of the art equipment, and thoughtful planning. The paper will detail the means, methods, and equipment used on the project, as well as discuss several of the unforeseen conditions encountered during construction.

Jan 1, 2005

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of poros¬ity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geologi¬cal Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Re¬sources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of dissemi¬nated gold deposits a profitable technique.

Jan 1, 1989

By Nelson Alonso Portal Ravichaua, Melissa Esther Mendoza Tirado, Raúl Arévalo Saavedra

This study analyzes the implementation of an integrated strategy for environmental education and community awareness in Cajamarca, Peru—an Andean region affected by climate variability and the public perception of miningrelated water shortages. In collaboration with the Interactive Water and Earth Museum and the Newmont ALAC Foundation, three-month campaigns were conducted in schools and local communities. Key topics included the water cycle, climate change, and water availability, linked to urban infrastructure projects that improved flow rates through strategically located tubular wells tapping underground aquifers. The initiative addressed the challenge of communication in a context where mining is often blamed for scarcity, fostering scientific understanding of contributing factors. The study highlights how science-based outreach and institutional collaboration can strengthen resilience and promote sustainable water stewardship in mining-influenced regions.

Feb 22, 2026

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1989

By Jian Wang, Xiaoming Sun, Ming Jiang, Fuxin Shen, Chengyu Miao, Wenchao Zhao, Yong Zhang

The increased thickness of the coal seam leads to higher goaf roof collapse height. In contrast, the dynamic pressure from the mining of ultra-thick coal seams generates higher abutment pressures around the mined area and may affect the stability of roadways servicing these panels. To mitigate the deformation and damage issues in the roadways during the extraction of ultra-thick coal seams under a high depth of cover, researchers have proposed combining high prestress constant resistance support and roof-cutting technology (HPCR-RC). The deformation and failure mechanisms of the roadways during the extraction of ultra-thick coal seams under a high depth of cover, along with the mechanisms and field control effects of the combined support system, have been analyzed through theoretical analysis, numerical simulation, and field experiments. The research findings reveal that the high in situ stress, initial excavation disturbance, rotation, and subsidence of the fractured roof of the extra-thick coal seam led to significant deformation and damage in the roadways. High prestress constant resistance support compensates for the initial stress loss, reduces initial stress concentration, and absorbs deformation energy. Moreover, the roof-cutting technology severs the connection between the goaf roof and the roadway roof, disrupts the path of stress transfer, raises the level of roof backfilling in the goaf, and provides support to the roof, effectively alleviating the pressure on the coal pillar ahead and adjacent to the working face. Field experiments have confirmed the effectiveness of HPCR-RC, as indicated by a substantial decrease in surrounding rock deformation and support pressure within the roadways.

Sep 25, 2023

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduction through semi-infinite homogeneous and isotropic airway walls with convective heat and moisture transfer between their wet or dry naked surfaces and mine air with time variable temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for computation of the temperature distribution and surface temperature of the airway walls and floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. The presented solutions are derived for general conditions and they could be easily adapted to the actual ones. Results of the model represent basis for balancing heat and moisture transfer between mine air and its surrounding in deep mines under time variable temperature and humidity of the air and enable us to solve complicated dynamic changes of mine air temperature and humidity in an airway system by relatively simple mathematical tools. INTRODUCTION The importance of unfavourable influences and the costs of condition arrangements increases with mine depth. Precision demands on the methods which predict the environmental condition changes and by which it is possible to optimize condition arragements are still increasing. Environmental conditions in deep mines are determined especially by flow velocity, barometric pressure, temperature, and humidity of mine air. Therefore new and more exact mathematical models of mine air flow through airway system and those of heat and moisture transfer between mine air and individual important sources of heat and moisture are developed. The paper presented deals with description and solution of problems of heat and moisture transfer between mine air and airway walls as the rock mass is one of the important heat and moisture sources in deep mines. There are several different approaches to the problem. In some models the moisture transfer between mine air and airway walls is not considered at all. In other models the moisture transfer is described only by certain empirical coefficients. Simultaneous heat and moisture transfer is described seldom. This paper tries to describe in a simple way simultaneous convective heat- and mass-transfer processes taking place on wet naked surface of airway walls by means of corresponding

Jan 1, 1993

By Robert L. Runkel, Kenneth E. Bencala, Briant A. Kimball, Katherine Walton-Day

The solute-transport model OTIS and the reactive solute-transport model OTEQ were used to simulate geochemical conditions in Cement Creek, a tributary to the Anirnas River in Colorado. OTIS was used to depict instream zinc concentrations, and to simulate the effects of two remediation scenarios on zinc concentrations at the mouth of Cement Creek. These simulations do not account for effects of changing stream pH on metal concentrations. Preliminary simulations using OTEQ to account for instream pH changes were unsuccessful due to the spatial nature of mixing processes, and insufficient information about the thermodynamic properties of precipitates forming in mixing zones.

Jan 1, 2000

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonites to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath, 1986 and personal communication). These bentonites typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X¬ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated" bentonite to the oilfield since specifications are

Jan 1, 1989

By D. G. Krige

Discussion by D.G. Krige I read the paper "The jackknife approach" with interest. There appears to be a widespread misunderstanding of the kriging variance as a measure of the error variance of the kriged grade estimate of an ore block. Virtually all mineral deposits display skew frequency distributions and are subject to the well-known proportional effect. Thus, it is usual to find in an ore body, when subdivided a really into subpopulations, that the variances of the grades (or the total sills of the variograms) for the subpopulations will be correlated with the corresponding mean grades (usually linearly with the squares of the mean grades). Thus, the variogram will be station. When this feature is evident, the relative variograms for the subpopulations (i.e., with variogram values divided by the relevant mean squared) will be similar, or they could even be accepted at an averaged model for the whole ore body with stationarity. Using this approach, the kriging variance will reflect the relative error variance that is to be multiplied by the kriged block grade estimate squared to yield the usual kriging variance for purposes of confidential limits. The objection that the kriging variance does not take into account the local grades used for a block valuation then falls away. In the example given by the authors, the global mean grade is not recorded. But the global variance, taken at the value of the total sill, is 0.005, whereas the variance of the 11 values used in the example is 0.000152. The two variances differ by a factor of nearly six. If the relative variogram approach is applicable in this case, the need for a jackknife technique will fall away. Also note that, for skew distributions, the confidence limits for ore-block estimates will be skew as well, and symmetrical normal limits will not apply. RepIy by G.S. Adisoma and M.G. Hester There are a few interesting ways to utilize the block-by-block kriging variance that the authors have encountered. One of them is to classify a particular block into a proven-probable reserve or a possible-resource category, using a somewhat subjectively determined kriging variance value. Here, the kriging variance still represents the drilling density, i.e., data configuration more than the data values. Professor Krige mentions another ingenious approach through the use of relative variograms. This will yield a block kriging variance that takes into account local (block) grade, as he correctly points out, for purposes of confidence limits. However, we are more interested in quantifying the uncertainties associated with grade estimation in a much larger scale than a block. e.g., for a mining phase or the minable reserve. The jackknife, through the block kriging shortcut, provides a simple solution to obtain a single estimation variance for a general shape. The authors' main reference discusses different ways to handle skewed distributions typical in mineral resource estimation, e.g., the weighted jackknife approach or data transformation. Also, as with any technique, we can always improve our estimate by subdividing into smaller populations that are geologically and statistically separate domains. As we have mentioned; the jackknife is but a tool in our collection of tools to solve estimation problems. The jackknife's appeals are its simplicity and versatility. It is handy when no other solution is available, or when the available solution is not practical. It is used with other methods, not to replace them altogether. ?

Jan 1, 1997

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Adeyemi Adesina, Subhabrata Mishra, Syed Mohammed Mustakim, Malaya Kumar Jena, Shaswat Kumar Das

Utilization of low-grade manganese ore adopting the carbothermic reduction roasting process is a proven method to produce high-grade manganese ore. To minimize industrial waste and protect the environment, gas cleaning plant sludge (GCPS), which is a solid waste from steel industries, was employed as a reductant to perform the reduction roasting process. The optimum conditions to carry out reduction roasting of the low-grade manganese ore were found to be: a roasting temperature of 950 °C, a residence time of 2 h, 40% GCPS as reductant, and magnetic separation at 5000 G for a manganese ore size of –10 mm. A lowgrade manganese ore comprising Mn grade 31.27% and Fe grade 19.78% having a Mn/Fe ratio of 1.58 containing a high silica content of 26.48% was used for the carbothermic reduction roasting having mineral phases of pyrolusite (MnO2) and hematite (Fe2O3) as found from XRD. The gangue minerals were separated during the magnetic separation, and the upgraded product was obtained, which reached a maximum value of TMn 49.5% with RMn 76.55% and TFe 62.19% with RFe 42.51%. In the study, activated charcoal (AC) was also taken as a reductant for comparative analysis; the experimental results revealed that GPCS performed better than that of the AC, showing potential to be used as a reductant in metallurgical industries. However, the resultedMn/Fe ratio was very low for the reduced sample; therefore, it can be used for smelting along with high-grade manganese ores as a feed.

Mar 5, 2021

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thorough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield revenues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equipment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Arranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that, the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1990

By Son Hoang Nguyen, Thanh‑Hai Pham, Duoc Van Tran, Dung Thi Kim Nhu

Apatite ore plays a critical and irreplaceable role in fertilizer production and is being upgraded in quality in northern Vietnam. The old tailing of the Bac Nhac Son beneficiation plant (Vietnam) has a significant apatite amount in the form of coarse unliberated particles. These millions of tons of tailing ore have 6–8% of P2O5 content, which can be retreated to provide fertilizer factories. This work presents the results obtained in recovering apatite from this tailing in the laboratory. By the combination of the processes of classification, preliminary flotation, re-grinding and cleaning in the flotation column, an apatite concentrate of 30.68% P2O5 can be obtained with the total recovery of 37.76% from the initial tailing of 7.56% P2O5. The study results not only provide an appropriate technical solution for recovering the apatite ore from tailing ore but also have outstanding meaningness in the recovery of mineral resources under the context of a circular economy.

May 24, 2023

By M. Albrecht

I have been following the discussions on coal degradation started by the article "Degradation process in coal slurry pipe-lines," by M.G. Ayat and B.C. Scott. I agree with Mr. Dasher's comments in January that the title of the article was perhaps misleading as the information appeared to pertain more to processing the coal than to transportation. Specifically, the authors' conclude that the cyclone had an important impact on the degradation. Dr. Ferri's comments on degradation in other physical processes was very correct, handling of coal in a turbulent manner has an impact on the size distribution of the coal. This is one reason that when I design a coal system (mine to rail car) I try to minimize the total number of transfer and processing steps consistent with achieving the desired product specifications. Another area, mentioned in passing in the article, the impact of natural causes and the mining step, is of particular interest to me. A mine in West Virginia had a variation of 50% in the -6.35 mm (-0.25 in.) raw coal depending upon the direction of mining. Since it was a single unit mine, this significantly impacted the final product. Two articles on mining's impact on size distribution are: • Stefanko, R., Chopra, 1K., and Ramani, R.V., 1974, "Mining influence on size consistency and washability characteristics of coal," SME Fall Meeting, September; and • Albrecht, M., and Olsen, D., 1980, "Mining methods impact on coal preparation plant design," 1st International Mine Planning and Development Symposium, September. Both articles presented information on variation of size distribution and cleaning plant performance on a coal depending on the mining method used. Both articles considered a single coal seam at one mining operation. Stefanko's article considered continuous and conventional mining of coal in Pennsylvania. Albrecht's article considered surface, underground continuous, and underground hydraulic mining of a coal in British Columbia. Both concluded that mining methods do impact coal characteristics. I agree with Mr. Ayat's comments in reply to Dr. Ferri's discussion, "... degradation is a multi-faceted phenomenon involving many natural and man-made factors." As efforts are being made to produce a higher quality (lower sulfur) coal, this topic becomes even more important

Jan 1, 1989

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.