Search Documents

By George K. Mitteer

The Cowles Mountain Tunnel was driven 2,073 m (6,800 ft) with a 3.43 m (11 ft 3 in) shuffle shoe TBM, for the San Diego County Water Authority, through extremely high strength granitic rock in the City of San Diego, Ca. The initial contract was $10.9 million. Tunneling began in March 1992 and all work was completed in May 1993. After the tunnel drive was completed in September 1992, a 2.44 m (96 in) Welded Steel Pipe was installed, welded and encased with cellular backfill to complete a small portion of the County's $970 million Capital Improvement Project. This paper will discuss the successful completion of a tunnel through some of the hardest most abrasive rock ever excavated with a TBM in North America.

Jan 1, 1995

By Stanislaw Wasilewski, Zdzislaw Krzystanek

Ventilation process in deep mines features relatively low efficiency. Commonly used passive control by means of regulators and flow throttling leads to remarkable energy losses that could be lower if effective monitoring and remote control of main fan operating point were implemented. In the paper, some results of investigation carried out in Polish coal mines to evaluate real energy losses in ventilation process are described. Different methods for main fans performance monitoring and control are considered and compared especially those using fan drive speed control to minimize power consumption. On the other hand some criteria for power evaluation are analysed and algorithms for optimum location of controllers in ventilation network are considered. The results of investigation are being implemented in the first system for monitoring and control of main fan operating point in Miechowice colliery.

Jan 1, 1995

By C. E. Capes

Reduction in the quality of resources and attendant increase in the quantities of fines to be processed present a major economic and environmental challenge for resource - based industries. It is becoming evident that agglomeration by immiscible liquid wetting will play a significant role in the treatment of these fines. Liquid phase agglomeration can be adapted to separate solids or liquids in highly divided form from liquid suspensions and emulsions. Diverse opportunities in coal fines recovery, novel fuels technologies and oily waste water treatment are cited here. The oil agglomeration of extreme fines from coal tailings, with consequent dramatic reduction in refuse for disposal, is now a commercial reality. It is suggested that this approach can serve as a prototype for the processing of extreme fines in an economical and environment ally sound manner.

Jan 1, 1989

By Berthold Pilz

The importance of a power economy that is efficient both in technological and economic terms has been clearly recognized in recent years. In 1977 the German Federal Government therefore introduced its Energy Research and Energy Technologies Program 1977-1980, which consolidates the government activities in the field of nuclear and non-nuclear energy research. The priority objectives of this program can be summarized as follows: safeguarding the medium- to long-term energy supply in the Federal Republic of Germany at reasonable overall macroeconomic cost, taking into account the requirements of environmental protection and the safety of the population. In the field of coal mining technologies, about 200 research projects are currently under way. A total of DM 1.7 billion is earmarked for research to be conducted in this area between 1977 and 1980.

Jan 1, 1979

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By Yadong Xue, Fei Wang, Hongwei Huang, Yan Sun

"Increasing attention to subway tunnel maintenance is being paid with the high speed development of urban rail transit system in China. A novel moving tunnel inspection equipment based on machine vision is developed in this paper. High resolution image acquisition system is proposed for tunnel crack and leakage inspection. The main components of this image acquisition system includes high speed CCD cameras, linear lights and high performance computer. To inspect the crack less than 0.3mm with a 3-5km/h speed in subway tunnel, we need to consider resolution and line rate of camera, pixels of cameras, range of inspection and illumination intensity of lights simultaneously. The optimization design is proposed to make the equipment more convenient for tunnel use. Entire tunnel situation can be detected and recorded in a single inspection process. This equipment has already been verified in Shanghai subway tunnel for defects inspection.1. INTRODUCTION In China, the quantity of subway tunnel has reached a large scale in recent years. Until 2014, there had been more than 2300km of subway tunnel in China which accounted for nearly three quarters of Chinese urban railway system (Zhang Chen,2015). In some metropolises like Beijing and Shanghai, most of the metro tunnels has already run over 20 years which within maintenance phase. This has brought about plenty of inspection work and maintenance work to guarantee the tunnel under the serviceability limit states. The increase of running mileage of subway tunnels in China has been displayed in Fig 1."

Jan 1, 2016

By A. W. Khair

This paper presents an analysis of respirabie dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.

Jan 1, 1985

By J. C. Yingling, J. W. Leonard

Introduction The absence of coal-face particle management heavily penalizes the transportation of coal from initial loading to final consumption. The penalties include dust problems, significantly reduced mine-loading-cycle productivity, mine-belt spillage, excessively high coal-preparation costs, chute blockages and dangerous pulverizer blockages at the final point of utilization. Fine particles commonly cause environmental and economic problems. It is well known that these fines can cause safety and environmental dust problems. But it is not well understood that these fines can also swell broken coal to a point where 5% to 15% more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading-cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long-established, and frequently misleading, basis of tonnage. It is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain nonfrothing chemicals, which are added to mine-face spray water, and by employing improved mine-face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed. The precursor to the work presented in this paper, involving the bulk density improvement for broken coal and the subsequent production gains for underground coal mines, was earlier presented in Leonard and Newman (1989). In the past, this topic has been studied and practiced only in byproduct coking in the steel industry. However, a potential exists for an increase in coal-industry productivity by improving the bulk density of coal to yield a subsequent reduction in delivered cost. This can occur with breakage, handling and treatment methods resulting in the loading of greater quantities of coal in fixed volumetric capacity haulage units such as mine cars, shuttle cars and scoops. Laboratory-based experiments to achieve an increase in productivity by increasing coal bulk density were discussed in Leonard, Paradkar and Groppo (1992). Chemical techniques using small quantities of commercially available reagents (surfactants) resulted in about a 13% to 15 % increase in bulk density, which was thought to produce a proportional increase in the productivity of a mine, together with a subsequent reduction in cost. The idea is to mix the reagents with the water that is used to spray coal during mining. In this paper, the impact of bulk density improvements on production rates is presented. Increases in production ranging from 60% to 88% of the bulk density increases are projected. This analysis was performed for atypical continuous-miner section. In the following sections, discussion and results of the analysis are presented. Discussion An analysis was performed to ascertain the impact of bulk density improvements on face-production rates for a typical continuous-miner section. Figure 1 illustrates the section layout and cut sequence. This layout and sequence is identical to the case described in King and Suboleski (1991). As can be seen, the section uses five entries and 12.2-m cuts that are taken by a remotely controlled continuous miner. The seam height is 1.5 m and two shuttle cars (5.7 t nominal capacity) are employed for haulage from the miner to the section feeder, which, throughout the cut sequence, is positioned as illustrated in Fig. 1. The simulation model was coded in the SIMAN simulation language. The major impacts of increased bulk density improvements on such a production system are as follows: •Shuttle-car payloads, in terms of the mass of coal transported per haul cycle, are increased proportionally to the increase in bulk density that results from the application of surfactant. •Shuttle-car discharge times should remain largely unchanged, because they are determined by the volume of material that is discharged, rather than the mass, and this volume does not change.

Jan 1, 1996

By John W. King

reserves are exploring to increase them.. Uranium exploration projects are known to be active or planned also in Guayana, Colombia, Ecuador, Peru, Chile, Bolivia, and Uruguay in South America; in the UAR, Nigeria, Angola, Mozambique, Malawi, Kenya, and Somali in Africa; and in Greece, Iran, Pakistan., Indonesia, and New Zealand. The above list, to which several might be added makes a total of at least 43 nations actively interested in exploration for nuclear raw materials. As we consider the distribution of the world's uranium resources, it is interesting to note that roughly one third of the total occurs in deposits that are economically dependant upon another product. The very large reserves of South Africa could not be produced for uranium alone, but gold has carried a sufficient part of the total cost that uranium can be recovered profitably. Approximately 40 percent of the US reserves, or 120,000 tons, are estimated as by-product recovery from porphyry copper and phosphate operations, but these reserves are not presently in production. The remaining two thirds of the world's uranium reserves have been sought, developed, and produced primarily for their uranium content. Those deposits are estimated to contain 613,000 tons of uranium oxide recoverable at less than $10 per pound. Nearly half of that uranium occurs in unmetamorphosed sandstone hosts, mostly of late Phanerozoic age--the Colorado Plateau type. About 30 percent is contained in the quartz pebble conglomerates of southern Ontario, Canada, and 20 percent is in magmatic-related deposits--veins, contact deposits, mineralized breccias, etc.

Jan 1, 1969

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia?s underground coal mining industry has reported few new cases of pneumoconiosis for over twenty years. Mortality from Coal Workers? Pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in x-ray surveillance programs are also lower in Australia. To understand this disparity, the National Institute for Occupational Safety and Health was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among United States coal miners. A number of factors, including coal dust exposure, silica exposure, and coal rank were examined as potential contributors to the above observed differences. Comparison of coal rank data from each country did not show any significant differences. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. Assuming that quartz is contributing to the greater number of cases of advanced pneumoconiosis in the U.S., more effective dust control measures, as well an independent exposure standard for respirable quartz in coal mining, need to be implemented to prevent this potentially disabling condition.

Jan 1, 2011

By James S. Scott

Effluents discharged from gold mills, and more recently from heap leaching operations, pose significant hazards to the environment if not properly managed prior to discharge. This paper describes the nature of wastewaters which must be treated, the treatment processes being applied in Canada and the capabilities of these methods in removing cyanide and metals. As a result of past practice the most common method of reducing cyanide in gold mill effluents remains that of natural degradation in tailings ponds. This method has proven capable of producing high quality effluents where large ponds and sufficiently long water retention times can be provided, but at many mines this has not been the case. Since 1981, as a result of these limitations there has been a strong move in Canada to chemically-based effluent treatment plants, particularly as additional processes became available. Canadian gold mills have become leaders in the use of chemical processes to remove cyanide, in terms of the variety of such processes in operation (five in total), the number of plant installations and the number of processes developed in this country. The hydrogen peroxide and Inco SO2-air processes, in that order, are being applied most widely. Alkaline chlorination, the initial process to be used fairly extensively has been almost totally replaced by the two methods mentioned above. Since a number of effective methods are now available for the treatment of gold mill effluents, the selection of a process for application at a specific mill requires careful consideration of:

Jan 1, 1987

By B. D. Hong

The Coal supply and demand review arrived too late to appear in the May issue. In 1991, the US coal industry produced 902 Mt (994 million st) of coal, according to preliminary data compiled by the Energy Information Administration (EIA) (Table 1). This amount was 32 Mt (35 million st) less than the record 933.5 Mt (1 billion st) produced in 1990. Most of the decrease in coal production occurred east of the Mississippi River. The substantial stock buildup that stimulated production in 1990 was not repeated in 1991. In addition, coal consumption by electric utilities and coke plants dropped by about 1.8 Mt and 4.5 Mt (2 million and 5 million st), respectively. Moreover, a higher level of coal exports failed to bolster the 1991 production. Production Surface mines accounted for about 59% of the 902 Mt (994 million st) of coal produced in 1991. Underground mines produced for 41%. More than one-fourth of the total coal output was from federal and Indian coal leases. Production of all ranks of coal, except subbituminous, declined in 1991. Bituminous coal is produced mainly in the East. It totaled an estimated 590 Mt (651 million st), a 6% decrease. Production of subbituminous coal, mostly in the West, rose 3% to a record 228 Mt (252 million st). Lignite output was from Texas and North Dakota. It decreased by 1 % to 79 Mt (87 million st). Anthracite production, all from eastern Pennsylvania, fell by 17% to 2.7 Mt (3 million st).

Jan 1, 1992

By Koehler Stout, Leroy Friel

INTRODUCTION Hydraulic sand fills have been extensively used in the United States in deep metal mines since 1940, and hydraulic fills have been placed in coal mines in Europe for many years. Numerous surface hydraulic fills exist in Appalachia for the disposal of coal mine waste and throughout the United States for the disposal of other mining, manufacturing, city, and paper company wastes. Hydraulic fills, as they are now deposited in stopes in mines, are often deposited at near minimum density and hence provide very little support to stope walls and pillars. If the support strength of fills could be increased, perhaps ground conditions in deep mines could be improved making them safer and more efficient. Surface fills deposited at higher densities could be covered with top soil upon which grass could be planted. The purpose of this paper is to describe procedures where the support strength of hydraulic fills can be considerably increased, and the focus of the paper is on applications to deep mines. In deep mines the objective of increased fill strength is to reduce heavy ground problems, improve destressing techniques, reduce or eliminate rock burst incidences, provide better working conditions, provide wall support so that more or all ore pillars can be removed, and improve mine safety, efficiency, and reduce surface environmental problems. The authors have shown that it is possible to improve fill strength used in deep mines. This paper reports the slurry filling procedure, fill testing techniques, and some recommendations for application in deep mines. Some of the reasons for low strength hydraulic fills are:

Jan 1, 1979

By A. Cordonnier, Ch. Obry, R. Evrard

In spite of the large annual expenditures and the vast field of activity covered, it cannot be said that many new grinding machines have actually come to light and modified the existing market for more than half a century. Manufacturers have mainly made advances in increasing machine sizes, efficiency and reliability, and in machine automation. The relatively recent emergence of roller presses is the only exception to this homogenisation of machine ranges. The development of roller presses in pregrinding has shown the advantages of compression grinding over the ball mill from the power consumption point of view. But classical roller presses still have maintenance problems due to the high grinding pressure. The FCB Research Centre has carried out much work in this field and in particular has studied the advantages of this process in pregrinding and integral grinding. These researches lead to the development of two new compression grinding machines. The first one, HOROMILL®, presented for the first time on the 8th European symposium on comminution at Stockholm, finds its application in the field of fine to very fine grinding in dry process. The second one, RHODAX®, presented at INTERMAT in Paris, covers the field of secondary and tertiary crushing and the first stage of grinding for most of the minerals in dry or wet process. Its high reduction factor permits to do with only one machine the work realised today with two or three crushing/milling stages. These two complementary machines offer a wide range of combination summarised on [Figure 1].

Jan 1, 1995

By Robert C. Dunne, Jeffery P. Vaughan

The Archean ores of Western Australia are in total the largest producers of gold in Australia. In addition to numerous small and medium sized deposits, the province also contains the giant Kalgoorlie Golden Mile deposits. A variety of different gold ore mineralogical associations has lead to the development of a number of different processing routes for both refractory and non-refractory ore types. Intense weathering and lateritization of Archean greenstones in the semi-arid Yilgarn region have resulted in the development of a deeply oxidized profile (60-100m) above most sulphide orebodies. Residual and re-deposited supergene gold within iron oxide/silica gangue of this zone responds well to CIP, CIL, heap and vat leaching techniques. Although gold is easily liberated in principal from oxidized gangue, in practice recoveries are sometimes affected by iron oxide coatings on gold grains, and by clay minerals which can interfere with plant performance. Refractory ore types in the Eastern Goldfields fall into three main categories - pyritic, arsenopyritic and telluride-bearing. Pyritic ores may be either free milling or require roasting. The difference appears to depend largely on whether gold occurs along grain boundaries or fractures, which can be liberated by grinding, or whether gold occurs as inclusions within pyrite grains and therefore cannot be satisfactorily liberated by grinding. Arsenopyrite bearing ores are not well understood and are complicated by what appears to be a variable degree of gold solid solution, in addition to included gold. Gold occurring in complex gold-silver telluride assemblages has traditionally been recovered by roasting in the Eastern Goldfields.

Jan 1, 1987

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

By W. C. Shanks

The Pioche District of Lincoln County in southeastern Nevada (Figures 1 and 2) has been an historically important producer of silver, zinc, and lead. Economic geology of districts in the Pioche area is summarized most adequately in recent reports by Tschanz and Pampeyan (1) and Gemmill (2) and only a few major aspects will be discussed here. Production in the Pioche District began in 1869 and early mining concentrated on silver-bearing fissures in lower Cambrian quartzites. In the early 1870's the Pioche District was second only to the Comstock Lode in world silver production (3). More recent mining activities have centered on the other major ore type in the area, bedded replacement of lower Cambrian carbonates by Ag-Zn-Pb sulfide ore. Production of replacement ore peaked around 1950. The present study is focused on the Pan American Mine because it is an excellent example of low grade carbonate replacement deposits, because there is little structural dismemberment, and because access was readily available. Most previous workers have suggested that both the fissure vein deposits and the bedded replacement deposits of the Pioche districts are a result of spatially related Laramide igneous activity. The purpose of this study is to determine whether ore genesis is a result of igneous activity or if mineralization might be related to late diagenetic processes such as formed Mississippi Valley "type" deposits. Stable isotopes of sulfur, carbon, and oxygen in ore and gangue minerals have been studied to determine the probable isotopic composition of the ore fluid and paleomagnetic studies of the carbonate rocks have been utilized to determine timing of mineralization. Additionally, petrographic and field studies of carbonate lithologies were undertaken in an attempt to delineate non-structural controls on ore localization. These studies are still proceeding and the results presented herein are, therefore, preliminary in nature.

Jan 1, 1979

By A. T. Yu

Once exploration is complete, "winning" of the ore can be viewed as fundamentally a bulk handling proposition. Whether it is to strip, break, size, extract, load, haul, or even process, the success of each of these phases will depend upon how effectively one can utilize-the methods and tools that are available in bulk handling. Since as much as 30 to 60% of the total delivered price of raw materials can be attributed to handling and shipping (ref. 1), this expenditure may spell the success or failure of an entire mining venture. In fact, it has become increasingly evident that handling and shipping are so intimately associated with mining that only when they are duly considered throughout the mine-to -smelter master plan as an integral part of a total system can an optimum operation be expected and the most economical ton of ore obtained, this total systems approach should not only take in handling and haulage in and out of the mine, but also storage and transfer at the terminals (ref. 2,3,t), including ship and barge loading and unloading which are likewise a major consideration (ref. 5). Much has been developed during the past century in bulk handling, particularly in its expanding use in the mining industry. In view of the major role bulk handling has played and will continue to play in mining, in commemorating AIME's centennial, this paper will attempt to outline the state-of-the-art at this three-quarter point of the 20th century - one that is marked by its industrial revolution and rapidly accelerating technological advances. Bulk handling systems Although many developments in bulk handling are worth noting. The most significant during the past three-quarters of a century are: the total systems approach to solving problems, automation, the increase in speed and capacity.

Jan 1, 1971