Search Documents

By Kalyan K. Bhattacharyya

A systematic slope design for open-pit mines has become a reality only in recent years. Advances in the science of rock mechanics, coupled with extensive use of computers, have enabled the numerical solution of slope design problems which were not previously amenable to analytical or numerical solution. This slope stability study was performed for the UJV-SB open-pit uranium mine of the Getty Oil Co., located in the Shirley Basin area, Wyoming. The purpose of the study was to determine the appropriate slope angles for a starter pit. The data generated during the mining of the starter pit would test the initial design and suggest appropriate modification in the design for future mining in the project area. There had been a history of slope failures in the open-pit uranium mines in the area due to the low competency of the overburden materials and adverse hydrological conditions.

Jan 1, 1979

By Robert A. Pond

Heavy (exceeding 35 tons) roadheaders have not seen much use in the United States, but are used extensively in Europe to excavate many types of underground openings in civil and mining applications. Early models of roadheaders were light and suitable only for utility excavation such as drift enlargement or chamber excavation, unless the ground was very soft and easily cuttable. Frontier-Kemper Constructors, Inc. is now using a 45-ton roadheader to excavate two mine slopes in Kentucky and a 70-ton roadheader to excavate a long decline at a new mine in Utah. Results to date indicate that heavy roadhead machines are an effective alternative to both conventional excavation and full-face boring machines in many cases; and where circumstances are favorable are a superior choice. This paper concentrates on applications in the mine development construction industry, but the conclusions are no less valid for civil construction.

Jan 1, 1983

By F. A. Gates, Bengt Samuelson, James E. Edmunds, S. McCune, Neil Hario, Norman L. Weiss, J. M. Bertram, A. M. Cavaliere, F. M. Jr. Stephens, D. D. Chiang

DESIGN BASIS Size of Project The size of the project generally is expressed in tons of ore milled per day, but company policies differ widely in this respect with a few adhering to this set figure but many expecting the design capacity to be liberal. To some companies that follow the latter practice a 25,000-tpd milling plant that cannot reach 30,000 or 35,000 tpd with¬out major additions is a disappointment. The engineers responsible for planning the operation must know what is intended. Other projects are sized according to the tonnage of product rather than of mine ore; examples are iron ore mills that express size in terms of tons per year of pellets or high-grade concentrates, heavy minerals plants in tons per year of rutile or ilmenite, cement plants in barrels per year, potash in tons per year of muriate, phosphate in tons per year of washer rock and flotation concentrate, and others. However, tons per day milling rate is also the common denominator in most of those instances because the major equipment has to be selected on that criterion. Equally important are operating schedules, particularly the number of operating days per week and shifts per day for ore delivery, crushing, grinding, and processing. Hours per shift also are an impor¬tant factor in design, particularly in the case of ore delivery, and the lost time expected for maintenance, cleanup, inspection, preventive maintenance shutdowns, and many others, has to be taken into ac¬count. Frequently, the ore deposit will vary in hardness and grade to such a degree that the capacity of the mill will vary widely from year to year and cannot be expressed as a fixed figure, but rather as an average over a calculable period, such as ten years, or as a specific daily capacity over the first two years, next four years, etc., or some similar projection. A good example of this kind of situation is Asarco's Mission operation 15 miles southwest of Tucson, Ariz., described by Weiss and Vincent,1 where the major rock types differed widely in hardness, so that a change in the proportion of these types in the mill feed could have imposed difficult design problems if a constant tonnage rate had been expected. Expected Life The life of a mining operation depends upon the size of the deposit and the rate of mining. The latter is a policy decision based on an economic analysis2 which, in turn, is based on many factors. From the point of view of mill planning, the estimated life of the operation determines many criteria and affects many decisions on strength of structures and degree of protection of men and materials, the quality of the materials-handling and process machinery, the type of delivery systems for ore to the mill and concentrates to the smelter or market, environmental considerations, and many others. Costly installations that may be excellent investments for a 20-year project may be waste¬ful for a 5-year operation. An example is the comparison of different methods of crushing or grinding. Take single- vs. multiple-stage grind¬ing-the former may be found more economical for a 5-year operation, and the other, more costly method more economical for a 15- to 20-year life. Mining and Ore Transportation The mining method and the means of transportation of the ore to the first crushing stage have far-reaching effects upon mill design, particularly the crushing sections, and upon site selection (see Chapter 2, Situation of Mill). Consequently, mill design cannot advance until the mine planning has reached at least tentative decisions concerning these important matters, or reach the final stages until much is known about the ore that may be expected month by month and year by year for a reasonable period. Methods of ore transportation used in over 90 underground and open-pit mines are listed briefly in Section 32 (Table 1), and more detail is found later in this section and in Section 10, Storage and Transport. These methods include surface railroad, trucks, conveyors, surface skips, underground skips, and tramming from hoist or tunnel. In surface mining, transportation of the uncrushed ore by rail or truck to the primary crushing plant-conveniently located for lowest overall cost-is most common. Rail transportation provides low perton-mile costs. Truck transportation, though in some cases less eco¬nomical, is more flexible and more adaptable to mountainous terrain; furthermore, recent improvements have reduced the operating costs to keep trucks competitive on low-grade ores. The design of the primary crushing plant will be essentially the same whether delivery is by truck or rail, but the location of the plant is subject to more rigid restrictions in the latter case because of grade limitations, and these in turn may adversely affect the selec¬tion of the mill site as well. The influence of truck haulage in reducing the stripping ratio in open-pit mines is an added reason for predicting a minor role for rail transportation in the future. The use of conveyors to transport ore from the pit to the milling plant involves (in most cases) crushing the ore to a reasonable size (10 to 20 in. maximum with today's crushers) before conveying. The Twin Buttes system3 which went into operation in late 1969, utilizes primary crushers (two) and conveyors to receive rock waste, ore, and low-grade stockpile material from trucks, then transport them to the appropriate destination. Flexibility is dependent upon the porta¬bility of the primary crushers. In the face of this development, inclined skip hoists are no longer important to the mill designers. Underground mines generally pose fewer problems of design; these will be discussed in Chapter 2. Character of Deposit The degree of homogeneity of the ore in various parts of the mine is an important factor. The characteristics that concern the millman (approximately in order of importance) are: hardness, assay, metallurgical response, size distribution,4 and moisture content. Under metallurgical response may be included degree of oxidation, mineral¬ogy, clay content, and reagent consumption, as well as process re¬sponse in general. Short-term variations-hour-to-hour, day-to-day, or even week-to-week-make operation of the plant more difficult, require greater flexibility of process design and, perhaps, also require more instrumentation and manpower. Uniformity of the ore in the characteristics noted previously and

Jan 1, 1985

By A. L. Frank, Benton

INTRODUCTION The selective sensitivity of plastic nuclear track detectors (PNTD's) to low energy 4He particles in an environment which also contains gamma and beta radiations has made these detectors prime candidates for the dosimetric measurement of the concentrations of radon and its daughter products in mine air. Their passive, integrating mode of measurement, small size, low weight and inexpensiveness are attractive characteristics for large scale personnel dosimetry. The detectors can be used in either active or passive dosimeters. In active devices, the PNTD is placed in close proximity to a sampling filter. The filter collects, from a calibrated air flow, all the daughter nuclei which are in suspension. As the daughter nuclei pass through the decay chain, through 214Po, a fraction of the 4He particles emitted are registered as latent tracks in the plastic. In passive devices, the PNTD is placed in direct contact with the ambient air containing the radio-nuclei concentrations to be determined. The active dosimeters have the advantage of excellent sensitivity, and the measured track densities yield very close approximations to accumulated Working Level (WL)** exposures. They have the disadvantage that the simplicity of the passive PNTD is lost, since a battery-driven constant flow-rate air pump is a necessity. The passive dosimeters are simple in construction and use, but they have the disadvantage that WL exposures are not directly measured and certain assumptions concerning radon and daughter equilibrium conditions must be made in determining WL exposures from the measured track densities. Also the sensitivities, in track densities per Working Level Hour (WLH) exposure, are much less than for active dosimeters. Dosimeters of both types have been investigated. Passive devices have been tested extensively both in the laboratory and in mines. Active devices have been laboratory tested. In our earlier measurements, cellulose nitrate plastic detectors were used exclusively, since this material had the highest sensitivity of the PNTD's then in use. When the properties of CR-39 plastic were discovered (Cartwright, 1978; Cassou and Benton, 1978), this material was used, where possible, to take advantage of its superior sensitivity. The results of our earlier work have previously been published (Frank and Benton, 1977). * Research sponsored by the Bureau of Mines, U.S. Department of Interior, under Contract No. JO-188003. ** A Working Level is defined as any combination of the short-lived radon daughters containing 1.3 x 105 MeV of potential 4He-particle energy per liter of ambient air. PASSIVE DOSIMETRY In the earliest testing of PNTD's for passive WL dosimetry, a single strip of cellulose nitrate plastic was used to determine the total cumulative 4He-particle activity in the air of simulated uranium mine and uranium mine environments (Rock, 1968; Rock [et al], 1969; White, 1969). The measurements yielded a close relationship between track densities and WL exposures in a controlled, static environment, but poor accuracy in the active mine tests. It was assumed that equilibrium differences contributed largely to the variations found. The response of PNTD's to airborne 4He-particle emitters, derived by Lovett (1969), demonstrated that detectors such as cellulose nitrate, which has a sensitivity cutoff at 4He-particle energies below the emission energies of radon and its daughters, are equally sensitive to the activity concentrations of radon, 218po(RaA) and 214Po(RaC'). Since radon does not contribute to WL as it is defined, and since, under normal ventilated uranium mine conditions, the radon activity constitutes about 40% to 70% of the total 4He-particle activity, the WL exposures calculated from measured track densities are very sensitive to the particular radon daughter equilibrium conditions. Also, the detector does not weight the individual daughter activities in proportion to their importance to WL. The equation for WL is WL = 0.00103C2 + 0.00507C3 + 0.00373C4 (1) where C2, C3 and C4 are the activity concentrations of RaA, RaB and RaC-C', respectively, in pCi/[L]. The detector leaves C3 unmeasured and weights C2 and C4, equally. [This problem has been approached by Domanski et al (1975, 1979), for some non-uranium mines, by measuring equilibrium conditions throughout the mines to determine a mean value for A, the inverse of the Working Level Ratio (WLR = 100 WL where C1 is the activity of radon-222 in pCi/[L].) The distribution of values allowed Domanski to determine probable errors in calculating WL exposures from track densities. However, measurements of equilibrium conditions in U.S. uranium mines (Breslin et al, 1969; Holub and Droullard, 1978) indicate that this method would not be accurate enough for uranium miner personal dosimetry.] A two-element dosimeter was designed at our laboratory to compensate for equilibrium variations. The first element is a radon detector; the second is a detector for the total 4He-particle activity in the ambient air, just as in the single element dosimeters cited above. The addition of the radon detector allows the equilibrium conditions for the individual nuclei to be determined, given certain assumptions concerning the interrelationships between the nuclei concentrations in mine air. The two detectors and the problems involved in calculating WL exposures from their measurements are discussed below.

Jan 1, 1981

By R. H. Parker, B. A. Wills, D. G. Binns

Introduction With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the fine mineral particles in these ores. Not only is this expensive, but it leads to greater losses in slimes. Gravity concentration techniques become unacceptably inefficient for particle treatment below 25 to 50 µm, and even flotation fails in the ultra-fine range. Ore from the South Crofty mine near Redruth, Cornwall, was subjected to thermal pretreatment in the hope that differential thermal expansion of the minerals would lead to intergranular cracking, and thus enhanced liberation. South Crofty ore contains about 1% tin as cassiterite associated with a complex assemblage of quartz, chlorite, tourmaline, and hema¬tite in granite and slate. Recovery of cassiterite can be as low as 70%, as overgrinding occurs during stage reduction of the material to 1 mm (primary grinding) and 180 µm (regrinding). Cassiterite is present in grain sizes ranging from submicroscopic to + 10 mm, the bulk being predominantly in the range of 50 µm to 3 mm. Experimental Flat polished sections of the ore were photographed in reflected light using a Vickers M17 microscope. The sections were then heated in a Carbolite LMF4 muffle furnace. The heating rate and temperature were monitored by a thermocouple immersed in the bed of particles. Previous work by Sherring (1981) on the same material showed that a 55% reduction in grinding resistance occurred when the material was rapidly heated and cooled through the quartz inversion tem¬perature (573°C), where a volumetric expansion of 0.86% occurs. The samples were therefore heated to 650°C at 26°/min, and were then water-quenched to room temperature. The effect of heat treatment on the mineralogy and fracture network was assessed by examining the same area after treatment. Results Most of the sections examined showed that extensive transgranular cracking occurred as a result of heat treatment. Such cracking, although weakening the rock and hence reducing the work index, would in no way enhance the liberation of the cassiterite from the host minerals. Intergranular cracking, which would lead to enhanced liberation, was difficult to discern under reflected light, but there was evidence of such cracking in some of the sections examined. Figures 1 and 2 are examples of typical sections before and after heat treatment. Figures la and lb - show cassiterite in hematite, Fig. lb, in normal incident illumination, illustrating clearly that after heat treatment, transgranular fracture is evident in the cassiterite. If any intergranular cracking has occurred, it is not evident in this photograph. Figures 2a and 2b show cassiterite in quartz before and after treatment. Fracturing in both minerals after treatment can clearly be seen, and there is evidence of intergranular fracturing. However, protruding "arms" of cassiterite are severed by transgranular fracture. Subgrains of quartz have also been isolated by trans¬granular fracture. There is major transgranular cracking across the wider sections of cassiterite. Discussion The effect of rapidly heating South Crofty tin ore to 650°C, followed by water-quenching to room temperature, has been studied by observing the fracture networks in mineral grains. The choice of 650°C as the heating temperature was influenced by the work of Sherring (1981), who found considerable reduction in grinding resistance after thermal pretreatment of the same ore. Scheding et al. (1981), however, have shown, by means of a crude calculation, that heat treatment cannot be justified solely on the basis of reduced grinding costs. The cost of heat treatment far out-weighs that of grinding, resulting in the combined costs for heat treatment being over six times that for grinding unheated material. The most economically attractive aspect of heat treatment is the possibility of enhanced liberation of the valuable mineral due to increased intergranular rather than transgranular fracture. Grinding costs would be greatly reduced by improved liberation at coarser sizes, and the costs of ancillary processes, such as dewatering and tailings disposal, would be reduced. The most significant economic effect, however, would be in improved metallurgical efficiency. Improved liberation would increase concentrate grades, and recoveries would be higher, particularly in the case of ores where high slime losses are produced due to the excessively fine grinding required to produce adequate liberation. Manser (1983) has shown that only a 1% increase in tin recovery, at the same concentrate grade, would be sufficient to offset heat treatment costs on South Crofty ore. Heavy liquid analysis and shaking table separation have been used to evaluate the effect of thermal treatment on processing (Binns, 1984; Scheding, 1981; Sherring, 1981). However, treatment of unheated and heated samples of South Crofty ore, ground to the same product size, by such methods have shown little evidence of improved metallurgical efficiency after thermal pretreatment. The large amount of transgranular fracturing revealed by reflected light studies helps to explain this lack of improvement. Nevertheless, from the evidence of some of the fracture work, it is surprising that no improvements in metallurgical

Jan 1, 1988

By Simon D. Strauss

The recession that began in late 1980 has proved to be not only prolonged and severe, but in certain ways unique in its effect on the mineral industries among the periods of economic slowdown experienced in the Western world since the end of World War II. This time almost all minerals have been affected. In previous business turndowns, by contrast, some mineral sectors have with-stood economic adversity well. They experienced little or no adverse effect-thanks either to a strong secular expansion in the markets for their particular product or to specific factors that caused demand to be well maintained. For example, aluminum, molybdenum, and nickel are three metals that enjoyed extraordinary growth in applications during the years 1946-1973. These metals were little affected during the recessions that occurred in that era. Similarly, coal did not suffer a pronounced drop in sales in the 1974-75 turndown because, with the price of oil rising sharply, a switch away from oil and back to coal was clearly indicated for some energy-intensive applications. Oil itself was largely impervious to the ups and downs of the business cycle until very recently. And the precious metals, gold and silver, have often been regarded as benefiting from reduced economic activity because labor becomes more available, productivity rises, and operating costs diminish. In the current recession, however, no major mineral has escaped the broad trend. The secular growth factors that were previously so evident for aluminum, molybdenum, and nickel have disappeared, at least temporarily. The stable pricing behavior that previously characterized all three of these commodities has been replaced by extreme price weakness and apparent inability of the major producers to continue their roles as market leaders. Coal and oil both have suffered from a sharp drop in energy requirements. There are those who now anticipate a collapse of the market control over oil prices so clearly exercised by OPEC since 1973. If oil prices are no longer effectively controlled by the governments of the exporting countries, then coal prices are also certain to be affected. And the combination of high interest rates, tight money, and a change in public perceptions of precious metals put the skid under gold and silver quotations in 1981 and early 1982. Although inflation has been viewed as the scourge of most Western countries ever since the oil crises of 1973-74, prices-in constant dollars-of most minerals have not risen. On the contrary, with the exception of the precious metals and oil, for most minerals the prices that prevailed at the end of 1982 were close to the levels of the Great Depression of the 1930s in constant dollar terms. Table 1 compares prices for copper, lead, zinc, and aluminum at the end of 1982 with the average prices in 1934, stated in constant 1967 dollars. This emphasis on prices for mineral commodities reflects the fact that profits of mining enterprises vary directly with the level of prices. Manufacturing and retailing enterprises march to a different tune. They establish sales prices based on costs. Their profits tend to vary with volume. Commodities are for all practical purposes fungible, that is the advantages of known brands in marketing manufactured goods have little application in a commodity market. Thus the individual seller of minerals is unable to establish his sales prices. Except where a monopoly is present, he must sell at the going market. His option is to abstain from selling if he finds the price unremunerative. In past recessions, some mineral producers chose to do precisely that-either accumulating a substantial share of their output in inventory or, in prolonged downturns, abstaining from production. During the current recession, however, private-sector mining companies did not have the option of accumulating inventories to any great extent. Capital costs for new mineral projects or for expansion of existing facilities have escalated at an alarming rate since the early 1970s. Added to this has been the heavy cost of installing pollution control or safety equipment to comply with the regulations adopted in most industrialized countries (and particularly the United States) since 1968. The consequence has been that the financial position of most major mineral enterprises in mid-1980 was already strained. To finance increased inventories meant incurring additional funded debt at high interest costs, thus impairing the concern's credit rating. Management Choices Private-sector managements have had to face up to the alternative of either continuing to produce at an unchanged rate and marketing output at unremunerative prices or reducing output. The latter has meant either operating at a curtailed rate, with con-

Jan 3, 1983

By Elza Burch

Introduction The feeding to zero concept involves feeding 600 µm x 0 (28 mesh x 0) size raw coal to heavy media (magnetite) cyclones along with the +600 µm (+28 mesh) size coal. Traditional circuits employ desliming or removing the 600 µm x 0 (28 mesh x 0) size fraction and feeding the cyclones +600 µm (+28 mesh) size coal. The feeding to zero concept recirculates 600 µm x 0 (28 mesh x 0) fines in the circuit. At the same time, a portion of the fine material is continuously withdrawn and recovered. This, in turn, prevents a fines buildup. This concept eliminates desliming screens and secondary fines circuitry for recovery of 600 x 150 µm (28 mesh x 100 mesh) coal. The result is a very simple circuit. Feeding to zero at Island Creek Island Creek Corp. was the first involved with the new concept in 1976. The company needed a temporary plant for the 9.5 mm x 0 (0.4 in. x 0) raw coal at its Pond Fork mine, near Madison, WV, while a full-scale plant was being designed and built. At that time, the Childress Corp., of Beckley, WV, became interested in the feeding to zero concept. Island Creek awarded a contract to Childress to build a single cyclone modular plant, incorporating this feeding to zero concept. The plant was erected in three months. The Pond Fork modular plant proved successful in attaining the desired feed rate of about 63.5 t/h (70 stph), while maintaining good separating efficiencies and low magnetite consumption rates. The 9.5 mm x 150 µm (0.4 in. x 100 mesh) clean coal was recovered and the 150 µm x 0 (100 mesh x 0) size was disposed of to waste. The full-scale plant was completed about two years later and the Pond Fork modular plant was moved to Holden, WV. There, it was incorporated into the Holden 29 preparation plant as a separate circuit for cleaning -25 mm (-1 in.) coal. In 1976, a similar plant was installed in Virginia by another company. These two plants are believed to be the first two operational plants in the United States incorporating the feeding to zero concept. Island Creek subsequently contracted with Childress for an identical plant at the Coal Mountain operation in West Virginia. The plant operated for three years before the mine was closed. The unit was then moved to the Spurlock mine near Martin, KY where it continues to operate. The successful operation of the Pond Fork and Coal Mountain plants before and after relocation proved both the performance and moveability of this type of circuit when constructed in a modular fashion. Since the first two plants were built, Island Creek has incorporated the feeding to zero circuit in nine additional plants. A grand total of 33 cyclones have been installed using this concept. One is the Providence mine, near Providence. Providence preparation plant Island Creek contracted with J.O. Lively Corp. of Glen White, WV in July 1978 for the construction of the Providence preparation plant. The plant began operation in February 1979. The construction period was about halved by building the plant with modular design concepts. Prefabricated sections, floors, and sides were brought in as units and then bolted in place. The Providence plant has a good track record of processing coal at a feed rate of 454 kt/h (500 stph). Feed coal to the plant has an average ash content of about 18% and sulfur content of about 4.5%. It contains about 22% refuse. The coal product has an average ash content of about 8% and sulfur content is about 3%. Raw West Kentucky No. 9 seam coal is conveyed from a box cut in the Providence mine to a rotary breaker. The breaker is fitted with 74 mm-diam (3 in.-diam) opening breaker plates. Therefore, it is well suited for removing trash, roof bolts, wood, and pyritic balls that are common in Illinois Basin coal. The -75 mm (-3 in.) coal is conveyed from the rotary breaker to

Jan 8, 1987

By David A. Zegeer

Since 1980, more than 40 miners have lost their lives by being trapped and suffocating in stock-piles, bins, silos, and similar facilities. Mine Safety and Health Administration (MSHA) is concerned about these accidents, most of which could be prevented if management and miners appreciated the hazard. In February 1986, the coal industry had a suffocation accident that drew national attention. A group of engineers were standing on a coal stockpile. It gave way under their feet. Five of the engineers were buried in the coal and suffocated. As with all fatal accidents, MSHA investigated the cause of this tragedy. I also asked my staff to look into the history of similar accidents. I found out it is rare to have multiple fatalities due to suffocation in material. But, over the years, there has been a long series of individual fatalities from this type of accident. Here are some examples. In Oct. 1985, a coal mine employee in Virginia entered a hopper to collect a coal sample. The feeders were started while he was standing in the hopper. He sank into the coal and suffocated. In Sept. 1985, an employee at a Texas sand company climbed onto a surge pile, to check a problem with sand flow. When other employees found him, the sand had swallowed him. Only his face and one hand were showing. Though the victim's face was clear of the sand, he suffocated before rescuers could free him. Many people do not realize you can suffocate in this kind of situation, though your head is free. Every time you exhale, the material has room to shift and press harder against your chest. Then you have less room to inhale. If this goes on long enough, it gets to the point where you cannot inhale at all. That is what happened to the victim in this accident. In May 1985, a plant operator at a Wisconsin sand and gravel operation purposely slid into the drawhole of a surge pile. He tried to break up large rocks that were clogging the drawpoint. Material piled on the side of the surge pile slid down and buried him. The operator was wearing a safety belt and line. But he was covered by 3 to 3.7 m (10 to 12 ft) of material and could not be pulled free. This incident illustrates another point. A safety line can help. But it is not enough. Workers should never put themselves in a position where loose material can fall on them from above. In Jan. 1985, a young Utah coal miner was waiting for a ride home from a co-worker whose job was at the tipple. A jam developed in the coal bin. The men could not clear the jam from the outside. So the young miner jumped into the bin. He started digging with a shovel at the toe of the coal pile. It caved in on him and he suffocated. The young miner had only three months of mining experience. He had not been trained for work around the coal bin. Since 1980, 16 coal miners and 26 nonmetal miners have lost their lives in loose-material suffocation accidents. Suffocation accidents occur in many areas around mines - bins, hoppers, stockpiles, surge piles, and silos, among others. One recent accident occurred at a surface coal mine in Illinois. The victim was walking over an area that had been drilled and blasted the week before. He fell into a void that had been crusted over with earth. He too suffocated. And many materials have been involved in suffocation accidentscoal, crushed stone, sand, salt, different kinds of ore, ammonium nitrate pellets used in blasting, and a powdery byproduct of iron ore milling called calcine. In addition to fatal accidents, there are near misses. We do not know how many. Most of them are not reported. A person who gets trapped in material, but is rescued, is usually unhurt. MSHA sometimes hears about these accidents by chance, or because they are reported in the local media. We do know that near misses are happening far more often

Jan 1, 1987

By Dennis S. Kostick

Introduction Soda ash is known chemically as sodium carbonate, an important inorganic chemical. It has been produced for several centuries by processing certain vegetation and minerals. The US soda ash industry has evolved from several small sodium carbonate mining operations in the West. Now, a nucleus of six companies produce about one-fourth of the world's annual soda ash output US producers currently dominate the world market. But certain international events are occurring that will reshape the domestic soda ash industry in the next decade. Historical perspective Soda ash is used mainly in the manufacture of glass, soap, dyes and pigments, textiles, and other chemical preparations. All of these are the first basic consumer products produced by developing societies. About 3500 BC, the Egyptians became the first society to use crude soda ash. The soda ash was used to make glass containers. It was most likely obtained from dried mineral incrustations around alkaline lakes. Soda deposits were virtually nonexistent in western Europe. So people resorted to burning seaweed to obtain the ashes. The ashes were then leached with hot water and the solute was recovered after evaporating the solution to dryness. The solute, a crude "soda ash" was impure. But, it could be used to make glass and soap. These two products and industries were important to the population and economic growth of the region. About 11.5 t (13 st) of seaweed ash was required to produce about 0.9 t (1 st) of soda ash. Along the coasts of England, France, and Spain, seaweeds with varying alkali contents became important items of commerce and sources of soda ash before the 18th century. The LeBlanc process used salt, sulfuric acid, coal, and limestone. It became the major method of production from about 1823 to 1885. In the early 1860s, Ernest and Alfred Solvay, two Belgian brothers, successfully commercialized an ammonia-soda process to synthesize soda ash. It used salt, coke, limestone, and ammonia. The Solvay process produced a better quality product than the LeBlanc method. In 1879, Oswald J. Heinrich presented to the Baltimore meeting of AIME, a paper entitled "The manufacture of soda by the ammonia process." The paper compared the two processes and foretold the demise of the LeBlanc technique. World production of soda ash in 1880 was 680 kt (750,000 st). Of that, 544 kt (600,000 st) was produced by the LeBlanc process. Of the 2.8 Mt (3.1 million st) of soda ash produced worldwide in 1913, only about 50 kt (55,000 st) was by the LeBlanc method. The LeBlanc process was never used successfully in the US, except for a brief period from July 1884 to January 1885 in Laramie, WY. Previously, soda ash had been produced by burning certain plants, as exemplified by the early Jamestown colonists, or by recovering small quantities of natural sodium carbonate found in alkaline lakes, such as those found near Fallon, NV, and Independence Rock, WY. Before the 1884 startup of the first synthetic soda ash plant in the US at Syracuse, NY, most of the domestic soda ash demand in the East was met by imports, primarily from England. Large-scale commercial production of natural soda ash began in California in 1887 from surface crystalline material at Owens Lake. Production from sodium carbonate-bearing brines at Searles Lake began in 1927 (Fig. 1). In 1938, during exploration for oil and gas in southwestern Wyoming, a massive buried trona deposit, presumably the world's largest, was accidentally discovered. Recent mineral resource evaluation by the US Geological Survey and the US Bureau of Mines indicates that the Wyoming trona deposit contains 86 Gt (93 billion st) of identified trona resource in beds 1.2 m (4 ft) thick or greater. Additionally, there is about 61 Gt (67 billion st) of reserve base trona. Of this 36 Gt (40 billion st) is in halite-free trona beds and 24 Gt (27 billion st) is in mixed trona and halite beds. In 1953, the Food Machinery and Chemical Corp. (later shortened to FMC Corp.) became the first company to mine trona in Wyoming. Soda ash demand increased.

Jan 10, 1985

By H. Lyn Bourne

Daily everyone depends on the great variety of glass products, so much so that glass is often taken for granted. In fact most people do not realize how versatile glass has become. Consider the various uses and then try to imagine a day in which we are not influenced by glass. Common uses include container ware, table ware, window glass, lead crystal, automobile glass, and fiber glass. Several less common, but important, uses include laboratory ware, pharmaceutical, TV bulbs, light bulbs, glass ceramics, optical glass, fiber optics, and laser glass. Corning, Inc., a leader in specialty products, uses nearly 1 000 different compositions to manufacture about 60 000 different products (Edwards and Copley, 1977). Glass is such a complex product that-definitions vary and exceptions can be found for most definitions. Glass is an inorganic amorphous (non-crystalline) solid. Most glasses are produced by melting of a mixture of oxide raw materials, and then cooled to room temperature. Soda-lime-silica composition.s account for about 90% of all glasses melted (Anon, 1973). The properties of the glass product come mainly from its chemical composition. All of the different glasses require melting a combination of raw materials and forming the molten material into the desired shape. Both the melting and the forming processes use sophisticated technology and these technologies require experts to manage these production systems. The manufacturing process is continuous and takes place in tonnage quantities, so adjustments in the batch to achieve the desired finished product requires a great deal of expertise. Raw materials are fed to the batch mixing area in very large quantities (tons in most cases). As a result, impurities in the range of 0.1% result in addition of that impurity within the molten glass in kilogram amounts. More than twenty different industrial minerals are consumed in the manufacture of various kinds of glass (O'Driscoll, 1990). This chapter describes the major and minor ingredients of the various glass batches. It discusses the roles of the various oxides in the glass batch and most importantly considers the mineral raw materials which supply the glass industry. Each of the raw materials is described in detail in other chapters so the geology and mineralogy sections are kept brief here. Container glass, by far, accounts for the most production; followed by flat glass, fiber glass, and specialty glass of which table ware accounts for the greatest tonnage. [Table 1] shows the general production data for 1987 through 1990. Statistics for many of the uses do not appear because production volumes are small compared to the major uses. The glass industry is organized in four categories: containers, flat glass, fiber glass and specialty glass. The US Department of Commerce, Bureau of Census, publishes production data about the glass industry in three different categories: 1) glass containers, 2) consumer, scientific, technical and industrial glassware, and 3) flat glass. The Bureau has very complete statistics about the glass industry in these three categories but they report production data in different units according to industry standards. Therefore, [Table 1] gives the production data in dissimilar units. The production of most glass articles follows similar steps. The raw materials are mixed and the resulting batch is fed into the furnace. In soda-lime-silica glasses melting begins between 600 and 900°C. At these temperatures CO, and other gasses are released which create bubbles in the molten glass. To remove the bubbles and insure complete melting the temperature is raised to between 1 500 and 1 600°C. This is the melting-refining stage during which the refining agents in the glass batch serve to aid in the release of gas bubbles, homogenize the melt, and prevent the formation of scum on the surface of the molten liquid. At the conclusion of the melting-refining stage the glass is too fluid for working and the melt is cooled to about 1 100°C to attain the proper viscosity for working and forming to begin. After the glass article has been made, it must undergo annealing (slowly and uniformly reheated and cooled) to remove thermal stresses that were created during the forming process.

Jan 1, 1994

By Raimo Matikainen, Pekka Särkkä

HISTORY The history of mining in the Outokumpu Co. shows continuous development of small and medium-sized mines, coupled with a permanent improvement in min¬ing methods and mechanization. Tables 1 and 2 provide a brief outline of the major events over the years of operation. Some of the mines have had relatively short lives as in the case of Nivala, Korsnas, Kylmäkoski, the surface pits of the Kotalahti, Vuonos, and Hammaslahti mines, and some very small pits. The sequence in which the mines started opera¬tions is shown in Table 1 and production increases in Table 2. GEOLOGICAL FRAMEWORK Most of the ore deposits in Finland (see Fig. 1) are situated in middle Precambrian (1500 to 2300 m.y.) formations corresponding to the Baltic shield. The ores and country rocks are generally firm, with a minimum compressive strength of 60 MPa (8700 psi). The sulfide ores, of importance to the national econ¬omy, can be divided into copper-nickel deposits, asso¬ciated with basic and ultrabasic rocks (1900 m.y.), and the sulfide ores found in well-preserved Svecokarelidic crystalline schists (1800 to 2300 m.y.) which contain varying amounts of copper, zinc, cobalt, nickel, and lead. Over 90% of the sulfide ore mined to date in Fin¬land and existing in the known ore reserves belongs to deposits situated in the main sulfide ore belt. This belt extends diagonally across the country over a breadth of Table 1. Sequence in Which Mines Began Operations 1913 Mining started at the Outokumpu mine (now called Keretti) 1928 Large scale systematic exploitation started in the Outokumpu mine Opening of mines: 1942 Nivala mine (1942-54) 1943 Yiojärvi mine (1943-66) 1947 Orijärvi mine (1947-54) (Mining started in 1757) 1948 Aijala mine (1949-58) 1952 Metsämonttu mine (1952-58 and 1964-74) 1954 Keretti's new mine plant 1954 Vihanti mine 1959 Kotalahti mine 1961 Korsnäs mine (1961-1972) 1962 Pyhäsalmi mine 1966 Virtasalmi mine 1967 Kemi mine 1970 Hitura mine 1971 Kylmäkoski mine (1971-74) 1972 Vuonos mine 1973 Hammaslahti mine 1978 Vammala mine Table 2. Ore Production of the Outokumpu Oy Mines Year 1000 t of Ore 1913-1928 252 1929-1954 13 075 1955 1 105 1960 1 784 1965 2 627 1970 3 269 1975 5 825 1976 5445 1977 4 939 1978 5 766 1979 5905 40 to 150 km, from Lake Ladoga to the coast of the Gulf of Bothnia. The main sulfide ore belt includes the Outokumpu copper-zinc, the Kotalahti nickel-copper, the Pyhäsalmi copper-zinc, and the Vihanti zinc ore zones. The Outokumpu ore district occurs in a mica schist area about 60 x 100 km, in association with belts of metamorphic Svecokarelidic quartzites, black schists, dolomites, skarn rocks, and serpentinites. The main ore minerals are chalcopyrite, pyrrhotite, pyrite, and sphalerite. In addition there are nickel and cobalt minerals such as cubanite and cobalt-pentlandite, which have been of economic importance. In this area, Outokumpu Oy exploits the deposits at Keretti and Vuonos. The latter was discovered as an extension of the Keretti ore field about 6 km to the northeast. The Kotalahti geological formation extends across nearly 400 km. The host rock of these mostly pipelike deposits is generally serpentinite, pyroxenite, or norite. The main ore minerals are pyrrhotite, pentlandite, and chalcopyrite. In this zone, the deposits of Kotalahti, Hitura, and Virtasalmi are at present under exploitation by Outokumpu Oy. The Vihanti geological formation is located in west¬ern Finland and is about 40 km wide and some 200 km long. The rock associations are crystalline schists including dolomites, mica schists, mica gneisses, gray¬wacke, and acidic or basic volcanic rocks, which change generally, in connection with the mineralization, into skarn and cordierite-anthophyllite rocks. The host rocks are dolomite, skarn, graywacke, and quartzitic rock and the principal minerals are sphalerite, chalcopyrite, galena, pyrite, and pyrrhotite. The accessory minerals are mainly cubanite, arsenopyrite, molybdenite, and native gold and silver. The two largest ore bodies being exploited at pres¬ent by Outokumpu Oy are the Vihanti mine, which pro¬duces zinc, lead, and copper, and Pyhäsalmi, which con¬tains copper and zinc. Deviating from the sulfide ore types described earlier is the Hammaslahti copper ore located in the southeast-

Jan 1, 1982

By K. -A. Björkstedt

INTRODUCTION Strassa lies in the central part of Bergslagen, a tradi¬tional mining district, on the eastern side of the Stora Valley at an elevation of about 200 m above sea level. A railway siding runs between the mine and the Stora railway station from which there are railway connections to the shipping port and iron and steel works in Oxelosund, about 224 km away. The distance to the provin¬cial capital Orebro is about 60 km. The climate is typi¬cal for this part of central Sweden and is illustrated by the diagram of monthly precipitation and temperatures for the years 1968-1975 (Fig. 1). HISTORY There is no certain information as to when the Strassa mine was first worked, but it is known from sur¬viving accounts of mine inspectors that there were smelt¬ing works in operation in nearby villages in the 12th century. An example is the Gusselhytta ore smelting works, 10 km south of Strassa, which dates from this period. Around the year 1540 there were two smelting works in Strassa, the Upper Karberg and Lower Karberg works. Ore for these smelters was probably taken from Strassa and from the adjacent Blanka mine. In the year 1624 Strassa is mentioned by the painter Jons Nils Krook in an account of the iron mines in the Linde mining district (Linde Bergslags Jarngruvor). Several mines were listed in the area, the deepest being about 30 m. An impressive power installation is mentioned in 1639, including a piston system of lashed poles for transmit¬ting power from the Stora River to the Strassa fields. Its length was 2670 m. Common ground comprising about 20.2 km2 (5000 acres) of forest was allocated in 1689 for the furtherance of mining operations. Until the beginning of this century only the rich cen¬tral parts of the ore body were mined and these yielded, after handpicking, lump ore suitable for smelter feed. An example of the ore grades from these early times is an analysis of ore from the "Big Mine" (Storgruvan) from the year 1873: 48.5% Fe, 0.008% P, and 0.06% S. This same year a total of about 18 000 t was ex¬tracted from the Strassa mine. OWNERSHIP The mine was owned and run until 1874 by a min¬ing association made up of 119 so-called "bergsman," who were homesteaders often engaged in agriculture and timber-cutting as well. In that year the Strossa Grufvebolag (Mining Co.) was founded. In 1906 it was con¬verted into a joint stock company, the Strossa Gruveaktiebolag. This was acquired in 1907 by Metallurgiska AB for the implementation of Gustav Grondal's beneficiating and briquetting methods, for which the Strassa ore was well suited. The same year saw the completion of a new ore dressing plant with an annual production of 46 000 t of ore concentrate. In 1911 the mine passed to new hands, and in 1913 it was purchased by an Austrian company. Extensive new installations were made and in 1915 a new dressing and briquetting plant was completed with twice the capacity of the old one. In 1917 the Strassa mine was acquired by Granges. Be¬cause of unfavorable business trends and technical diffi¬culties, mining operations were brought to a close in 1923. Pumping kept the mine free of water until 1933 but it was completely filled ten years later. Up to 1950 the surface buildings and installations remained intact but the large dressing and briquetting plant burned to the ground in that year. Today only the machine shop re¬mains from this earlier period of operation, now housing parts of the Mineral Processing Laboratory. The decision to take up mining operations again was made in 1955 and construction work began the follow¬ing year. Of the old installation, only the "southern shaft" could be used for some development drifting after it had been completed with a new headframe. Other¬wise, all the buildings and installations required for the operations had to be rebuilt. New installations ready by 1960 were office and personnel facilities, a new shaft and headframe, a sorting and concentrating plant, a macadam plant, settling basins, pump stations, and a railway and yard with transport equipment. The instal¬lation was completed with two plants

Jan 1, 1982

By August V. Castelli

Drilling fluids have changed over the years from water and/or water frequently mixed with local clays to scientifically com- pounded materials (mud). This change has occurred due to changes in drilling methods from percussion to rotary: depth maximum from 21 m in the first oil well to more than 9 000 m; and variety in types of well or hole to gas, oil, water, and mineral exploration. Environmental concerns about the composition of the fluid as to heavy metals and oil on the cuttings has recently caused changes in the materials used in the mud. The drilling fluid should perform the following functions (Darley et al., 1980): 1) Carry cuttings from beneath the bit, transport them up the annulus, and permit their separation at the surface. 2) Cool and clean the bit. 3) Reduce friction between the drilling string and the sides of the hole. 4) Maintain the stability of uncased sections of the borehole. 5) Prevent the inflow of fluids-oil, gas, or water-from permeable rocks penetrated. 6) Form a thin, low-permeability filter cake which seals pores and other openings in formations penetrated by the bit. In addition to these, the fluid should: 1) Not injure drilling personnel nor be damaging or offensive to the environment. 2) Not require unusual or expensive methods of completion of the drilled hole. 3) Not interfere with the normal productivity of the fluid- bearing formation. 4) Not corrode or cause excessive wear of drilling equipment. A number of industrial minerals, chemicals, and other materials are used as additives in the drilling fluid to accomplish these functions. Industrial minerals make up the highest percentage of the additives in a drilling fluid. Drilling fluids are classified according to their principal components: water, oil, and gas. If the major component is either water or oil, the component along with the suspension of solids, cuttings and additives is referred to in the trade as a mud. The largest use of some industrial minerals, such as barite and bentonite, is in drilling muds. For other materials, such as gypsum and limestone, drilling usage is only a small percentage of total demand. RAW MATERIALS [Table 1] lists the industrial minerals used in drilling fluids, their form, specifications, and uses. Each raw material will be discussed as to its mineralogy, physical and chemical properties, and the location of major deposits with respect to drilling fluids. Attapulgite Attapulgite is a crystalline hydrated magnesium silicate clay mineral, prized for its viscosity in saline waters. The particles are needle-like rather than the platelets common to most clay minerals. The specific gravity is 2.5 and the Mohs hardness is 1 to 1.5. Attapulgite is one of the materials sometimes referred to as fuller's earth. The major producing areas in the United States are southern Georgia and northwestern Florida. It also is mined in Spain, Senegal, the Republic of South Africa, Turkey, India, and Australia. Barite Barite is crystalline barium sulfate. It has a high specific gravity for a non-metallic mineral, 4.5 when pure, and is used as a weighting agent. Generally, the specific gravity ranges from 4.20 to 4.35. It is relatively soft with a Mohs hardness of 3 to 3.5 and is not very abrasive. Barite is inert, non-toxic, and clean to handle. Common contaminants are quartz, iron minerals, gypsum, and calcium carbonate. If there is considerable gypsum in the barite, it will thicken the mud. The major deposits in the United States are in north central Nevada, near Battle Mountain. The major producing countries, other than the United States, are China, India, Mexico, the former USSR, Turkey, and Morocco. The major deposits in India and Nevada, and some in China, are stratiform, commonly quite pure bodies in bedded sedimentary rocks.

Jan 1, 1994

By Simon D. Strauss

This paper discusses the ways in which the metals industries dealt with surplus capacity in the past, primarily the twenty years, 1950 - 1970. During this period, the bulk of metals production in the market-economy countries was controlled by private sector companies. Since then, public sector companies have played an increasingly important role in the metals industries of the market-economy countries. Of course, the change was not overnight. It occurred gradually over a period of many years. Indeed, by 1965, several developing nations had adopted policies of government control of metal operations previously in private hands. The metals industries are so many, so large and so diverse that the constraints of time make it impossible to deal with all segments. To illustrate the problems of surplus capacity in the metals industries during the period, this paper focusses primarily on three metals. One experienced rapid market expansion between 1950 and 1970; one had a growth more or less in line with the expansion of the world economy; and one lagged well behind the pace of industrial expansion. No one will be surprised if aluminum is identified as the metal with rapid growth; copper is identified as the metal that kept pace with the world economy; and tin is identified as the laggard. Individual computations of the rate of growth for these metals show some variations, but most estimates place the increase in aluminum consumption in the market economy countries between 1950 and 1970 at a compound annual rate of about 8%. The corresponding figure for copper is a compound rate of 4%. Tin consumption showed no growth. A widely accepted point of view is that sharply rising demand will force the price of a commodity to increase substantially in order to attract a necessary expansion of supply. The corollary to this is that stagnant demand will hold prices down, as there is no need to stimulate new supply and it may be necessary to force marginal producers out of the market. The experience with aluminum, copper and tin in the years 1950-1970 does not support this theory. In 1950, the average prices in the United States market as reported by the American Bureau of Metal Statistics were 17.74 a pound for aluminum, 21.24 a pound for copper, and 95.54 a pound for tin. The corresponding figures in 1970 were 28.74 a pound for aluminum, 57.74 a pound for copper and 174.24 a pound for tin. Aluminum, with the greatest market growth, rose by 60%, whereas tin rose 82% and copper by 172%. Clearly, other factors were a more important influence on price than was the trend of demand To revert now to the capacity issue, during the period under review aluminum demand was rising so sharply that that industry had no sustained problem with surplus capacity. Instead, if anything, capacity may at times have been a constraint on demand. The industry succeeded in attaining explosive market growth through imaginative research and promotion programs. Some of this growth was the result of substitution of aluminum for other commodities – steel, copper, wood and glass as examples. But much of the growth was the consequence of developing entirely new products through technological innovation. Prior to World War 11, the number of aluminum producers was extremely limited. Alcoa and Alcan in North American and Pechiney and Alusuisse in Europe were the dominant firms. The developing countries had virtually no production and in Japan and Germany production was only a small fraction of the North American output. During the War years the United States had financed the construction of many new facilities. After the war these plants were sold by the government to Reynolds and Kaiser in order to foster more competition in the market. Subsequently many other concerns became aluminum producers, both in the United States and elsewhere and competition for markets intensified.

Jan 1, 1989

By Michael A. Linkous, Mark J. Zdunczyk

Silica in the form of sand and sandstone is one of the most common, and at the same time, unique industrial minerals. Found in every rock type of every geologic age and virtually everywhere in the world, silica is used in products that touch just about every aspect of daily life. Imagine a world in the 1990s without computer chips, fiber optics, or glass, and you have just begun to understand how important silica is to the quality of life we enjoy. The elements silicon (Si) and oxygen (0) comprise roughly 60% of the earth's lithosphere to a depth of about 16 km. The crystal structure of silicon dioxide consists of one atom of silicon bonded to four surrounding atoms of oxygen to form a three-dimensional network of SiO, tetrahedra. This network makes up the mineral quartz (Murphy and Henderson, 1983), the most common detrital mineral in most sandstones. Quartz is also a major constituent of many igneous and metamorphic rocks and is widespread as a siliceous cementing agent in various rock types. Although quartz is common, sandstones, quartzites, and pegmatites and the unconsolidated sediments derived from them that have a silica content high enough and pure enough to meet today's market demands for quality and consistency are not common. USES AND SPECIFICATIONS Silica sand that is mined and processed for industrial uses must conform to the chemical and physical specifications set by customers. In the United States almost half of the silica sand produced is used in the manufacture of glass. Other important products include foundry sand, ground silica, blasting sand, and fracturing sand. Glass Sand Silica is the principal glass-forming oxide in a glass batch. Glass manufacturers develop model specifications for each source of silica sand used. These specifications broadly define the limits and ranges for chemical and physical properties of the sand and are used by the manufacturer in calculating the desired batch mix or formula. Some specifications may be critical to a glassmaker and require very stringent limits on the quantity of impurities in the sand. For example, the total iron oxide content of a batch is extremely crucial when making white or flint glasses (Mills, 1983). Iron is present in almost every raw material used in a glass batch and must be carefully controlled in order to obtain a consistent color in the finished product. It is difficult, however, for a raw material supplier to tightly control the chemistry of a naturally occurring material such as silica sand. To a great extent the commercial quality of a sand is determined by its geologic history. Realizing this, glass producers tailor their model specifications to each source of approved material. In general, a glass company is concerned most about the consistency of raw materials on a day-to-day basis. Soda-lime-silica glass was the earliest type of manmade glass (Baker-Can, 1967) and still accounts for most of the glass manufactured for commercial use today (Mills, 1983). It is relatively easy to melt and shape and is less expensive per ton to produce than most other types of glass (Baker-Can, 1967). Soda-lime-silica glass is used in fabricating containers, flat glass products, incandescent and fluorescent lamps, glass fiber, and many other products. Heavy minerals such as ilmenite, leucoxene, kyanite, and zircon are impurities on which strict limits are placed for a glass batch. Because of their refractory nature they either do not melt or only partially melt, which results in stones or feathers in finished glass. Aluminosilicates such as kyanite also contribute unwanted alumina to the batch as they partially melt. Limits are especially rigid for refractory mineral grains coarser than 0.60 to 0.425 mm (30 to 40 mesh). [Tables 1 and 2] present typical specifications for silica sand used in flat glass and container glass products. The percentages shown represent an average of many companies7 specifications.

Jan 1, 1994

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner's drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By Roger Malmström, H. Heden, Kjell Lidin

INTRODUCTION LKAB was formed at the turn of the century when the railways between the ore fields and harbors were built. The mines are situated north of the Arctic Circle in Sweden. Kiirunavaara is the largest mine, with a pro¬duction capacity of approximately 30 Mt/a. Malm¬berget has a capacity of about 12 Mt/ a. Both are under¬ground mines. Svappavaara, the only opencast mine currently in operation, has a capacity of about 4.5 Mt/a. The ore harbors are at Narvik for the Kiruna and Svappavaara mines and at Lulea for the Malmberget mine (see Fig. 1). Production in the form of finished products is shown in Fig. 2a, b, c, and d. Due to poor ore markets in re¬cent years, production and shipments have been cut back, but there was a positive swing in 1978. LKAB has been 96% state-owned since 1957. In addition to the iron mines in northern Sweden, LKAB has subsidiaries in central Sweden which produce sulfide ores, quartz sand, and uranium (Fig. 3). The mining methods employed are opencast bench stoping at Svappavaara and sublevel caving at Kiirunavaara and Malmberget. GEOLOGY The Kiirunavaara ore body is 4000 m long and av¬erages about 90 m wide, with variations in width from a few meters to around 150 m. The ore has been ex¬plored by deep drilling down to about 1000 m, but mag¬netic measurements indicate a depth of at least 1500 m. The Kiirunavaara ore is oriented in a north-northeasterly direction with a number of ores in the boundaries be¬tween the wall rock types. The ore in Kiirunavaara is mainly a fine-grained magnetite with a varying content of fine-grained apatite. The apatite content of the ore decreases with increasing depth. The other ores are all apatite-bearing and a couple are hematite ores (Fig. 4a, b). The ores are sedimentary, tilted, and tectonically de¬formed. They have a lateral dip of 0.87 to 1.2 rad (50 to 70°). The contacts between ore and wall rock are distinct and sharp, but both the hanging wall and the footwall are brecciated and impregnated with magnetite. The footwall of the Kiirunavaara ore consists of syenite porphyry with a low quartz content and rela¬tively good strength; the hanging wall consists of quartz porphyry. Both types are known as Kiruna porphyries. The ore at the boundary with the hanging wall is often rich in kaolin. There are a few veins of syenite porphyry running through the ore, which has a few major faults (Fig. 4c, d). There are two sharply delineated ore grades in Kiirunavaara: low phosphorus ore with less than 0.1 % phosphorus (about one-third of the ore) and high phos¬phorus ore with greater than 0.5% phosphorus. The iron content is 67% in the low phosphorus ore and 60% in the high phosphorus ore. These ore types are sold as different grades and so are kept separate during mining. MINING AT KIIRUNAVAARA The Kiirunavaara and Luossavaara ores were first mined using opencast bench stoping in 1902. When mining costs rose owing to higher waste removal, under¬ground methods were adopted. In the mid-1950s, the ores were still being mined on the surface at the same

Jan 1, 1982

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By Alexander N. Winchell

"THE MICHIGAN COPPER DISTRICT.Location. The copper mines of Michigan are all in the north¬ern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeast¬erly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of.location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as fol ,lows by Foster and Whitney : Location: As shown on the accompanying map, the Mar-quette district extends from the region of Marquette on Lake Superior westward for about forty miles. The main basin of the district is only about three to six miles wide, but outlying areas which are commonly regarded as belonging to the same mining unit, make the north and south dimension of the district about twenty miles. The most productive portion of the area is in the vicinity of Negaunee and Ishpeming, .about ten miles from Mar¬quette, but important mines are found also all along the range as far west as Michigamme and also to the south in the fold known as the Republic Trough. Comparatively recent developments indicate that important ore bodies have been developed in the outlying Swanzy district about eighteen Miles nearly due south of Marquette.The Marquette Iron District.History: The first discovery of iron ore in the Lake Supe¬rior region was probably that made in 1844 near the site of Ne-gaunee by the government surveying party in charge of William A. Burt, sent out under the direction of Douglass Houghton. This surveying party was using a solar compass, invented by Mr. Burt, and noticed variations in the direction of the magnetic needle at various times and places, but. on the 19th of September, while running the east line of Township 47 North, Range 27 West, the needle varied from its normal position until it stood nearly at right angles thereto."

Jan 1, 1920

By I. Iwasaki

There are many reasons why the US mineral and primary metals industry is in its present state. Undoubtedly, a flood of imported goods in all sectors is playing a major role in the plight of our raw materials industry. Domestic industry is becoming increasingly aware of the importance of its international competitiveness. And we are beginning to wonder what is happening to our technological edge. A number of factors affect the international competitiveness. Engineers cannot do much about some of these factors - labor costs, tax policy, government relations, interest rates, dollar strength, and labor-management relations. Something can be done about technology, however. Some say technology is so easily transferable today. But I would like to believe that we have the ability to apply it better than others. Not too many years ago, "made in Japan" meant cheap and shoddy products. Today, Japan has completely changed its image. The US is beginning to feel the threat from Japan's low-cost, defect-free products with dependable delivery. With worldwide recession and the strength of the dollar, we were shocked at the sudden weakness that developed in America's industries, not only in the international market, but domestically as well. What went wrong and what can we do about it? Senior executives from 300 large American manufacturing companies were surveyed. These executives believe US companies must: • invest in more efficient plants and equipment (27%); • invest in more research and development (23%); • improve the quality of service to customers (23%); and • adopt more aggressive marketing tactics and strategies (14%). Are we not doing enough research? The US has nearly four times as many people engaged in research and spends four times as much for research as Japan (Fig. 1). There is little doubt about the excellence of the US performance in basic science as indicated by the number of Nobel prize recipients. Japan has produced only four winners since World War II. Look at technology trade of five countries (Fig. 2). Again, US performance has been remarkable. An interesting observation here, is that the United Kingdom, another country with economic woes, is also in the black, West Germany and Japan, both with trade surpluses, are net technology importers. It is apparent that the US' performance in the commercialization of new knowledge is much more in question. Japan had $50 billion of trade surpluses with the US last year, which led to some friction between Washington, DC and Tokyo. Comparing the technology trade of Japan and the US in more detail, Japan imports disproportionately large amounts of technology from the US and Europe. This data is rather old, 1978, but the general trend is not too different even today. It is generally believed that scientific research leads to innovative technology, then to economic payoff. But, after seeing the current technological challenge by Japan, we are forced to change this traditional view. Investment in research may eventually lead to economic payoff, but not directly. There is a middle ground between new knowledge and its commercialization. This is an area where the Japanese have been successful. Until the 1970s, many western companies licensed patents to Japan for quick profits. But, in recent years, these companies have become more discrete about the terms of technological transfer. As a result, a number of scientists and engineers are expressing deep concern over the future of technological developments in Japan. A survey was conducted on 450 research managers of private industries in Japan on how they viewed the level of breakthroughtype original research in Japan as

Jan 6, 1986