Search Documents

By J. G. Groppo

In 1992, 48 million tons of fly ash (not including bottom ash, boiler slag and FGD material) was produced in the United States, according to the American Coal Ash Association. Of this amount, 27.2% was utilized; although the percentage of fly ash utilized increased from 20% in 1980, there is significant potential to increase utilization. One of the primary driving forces behind increased utilization is increased disposal costs due to more stringent environmental controls and regulation. Fly ash is classified as a natural pozzolan and finds significant use as a cement additive. It has been found to increase the plasticity of the cement mixture while lowering the amount of mix water needed. In addition to improving leveling and finishing properties, fly ash improves pumpability as well as decreases the heat of hydration of the concrete mix which is particularly important in massive concrete structures such as dams where the concrete needs to cool as quickly as possible. The Loss on Ignition (LOI) of fly ash is an important quality when considering utilization. The LOI is primarily due to the presence of unburned carbon and the standard specifications for the use of fly ash as a mineral admixture in Portland cement concrete are given in ASTM C618-89a. which sets an LOI limit of 6%. However, many states have set a more stringent limit of 3%. The primary reason for the lower LOI specification is that carbon adsorbs air entraining agents which limits freeze-thaw resistance. This is particularly important in climates such as the midwestern US where multiple cycles of freezing and thawing are typical in winter.

Jan 1, 1995

By John F. Clarkson

White Pine Copper Company built and operated, from August, 1962 through May, 1963, a pilot plant to recover copper using a cyanide percolation leach of the sand fraction (+400 mesh) of the mill tailings (1, 2, 3). The pilot plant runs were metallurgically successful and preliminary engineering studies for a full scale operation were completed under contract by an outside engineering firm. Unfortunately, the net return projected at that time did not justify the proposed capital' investment. In the summer of 1973 the project was revived. The rise in selling price of copper over the previous ten years, compared to the projected operating cost of the leach plant, increased the calculated net return on investment with the most recent figures showing a 30% DCF. Basically, the reason for this favorable shift in profitability was that the cost for many of the reagents did not go up as fast in the previous ten years as did the selling price of copper. Using the Chemical Marketing Reporter costs, NaCN sold for 18.3¢/lb in 1963 and 20.75¢/lb in August, 1973. During this same period H2S04 went from $23.50 per ton to $35.90 per ton. In comparison, producer's prices for electrolytic copper were 31¢/lb in 1963 and 619 in 1973. Thus the price of copper went up 97% while the two reagents only increased 13% and 53%, respectively. The capital investment also escalated but, again, not to the same extent as the selling price of copper. These price differences no longer are valid' but they did provide justification for reexamining the project.

Jan 1, 1975

By Hal McVey

Introduction The role of marketing in the minerals and mining industry takes on different degrees of importance depending on the commodity, but nowhere are sales and marketing more important than in industrial minerals. This article compares industrial minerals marketing with the marketing of other mining and mineral products. Marketing in Mining Some broad generalizations on the marketing of industrial minerals in relation to other mineral products can be made without getting bogged down with exceptions to generalizations. Two totally different areas of mineral production are crude oil and natural gas, and metals, including ores and concentrates. Although these commodities are the basis for two completely different industries, they share two things in common from a marketing standpoint: • Their value per unit volume is usually high enough so that they can be transported great distances. • Their specifications are readily definable and, therefore, the quality of a standard product from a production run can be communicated by stating certain chemical and physical features. This permits sales to be consummated by telephone, telex, and letter, without the need to pretest the products under use conditions. In regard to the first item, industrial minerals, as opposed to oil, gas, and metals, are in most instances site specific. Location of the point of production in relation to the point of use is of paramount importance based on a generally lower unit to volume value. This means that transportation is a major factor, with the cost of getting the mineral to market commonly exceeding its f.o.b. value. Coal marketing has many characteristics in common with industrial minerals. Coal sales can es-

Jan 11, 1983

By Charles Fisher

When considering the biodiversity of fauna endemic to hydrothermal vents or hydrocarbon seeps one must consider not only the numbers of unique species, but also the physiological diversity (and potential biochemical/physiological uniqueness) of the fauna. The deep ocean ridge system is home to some of most extreme animal habitats found on Earth. In addition to the high pressure, low temperature, and lack of light characterizing the deep-sea in general, hydrothermal-vent environments are characterized by toxic chemicals and temperatures that would be hostile to most other animal life. Perhaps even more challenging than the absolute levels of chemicals, dissolved gases, and temperature with which vent animals contend are the extreme gradients in time and space of all of these parameters. For example, temperatures around some vent animals can fluctuate from ice-water to hot-tub levels over seconds and can exceed 350°C only inches away. Specially adapted animals not only tolerate these conditions, they often thrive under them. As a result, the biomass of many deep ocean ridge ecosystems rivals that of coral reefs and tropical rain forests. In the Gulf of Mexico, hydrocarbon seepage through the sea floor driven by salt tectonics results in environments that are geologically very different from hydrothermal vents, but are geochemically similar enough that closely related animals are found in the two habitats. This includes seep mussels, clams, shrimp, worms, and other animals whose close relatives are found in hydrothermal vent environments. Although many aspects of the biology of the animals from the two environments are very similar, there are also significant differences in their life histories and physiologies that reflect the fundamental differences in the geology of their habitats.

Jan 1, 2008

By Frank H. Blair

A study of paleogeography and paleo-environment, coupled with modern geochemical techniques and geologic inference, points to the presence of unconventional platinum group metal deposits in domestic and foreign ultrabasic terranes. During the laterisation of the tectonized and serpentinized mafic and ultramafic rock units, onshore winds provided abundant low temperature chloride to the laterite-saprolite profile. Here, an environment formed where gold, silver and platinum was dissolved, transported and redeposited. Changes in climatic conditions have helped preserve the redeposited metals in fossil laterites. The definition of "unconventional mineral resources" used here is taken from the Cameron Volume of Unconventional Mineral Deposits published by SME-AIME in 1983: "Unconventional mineral resources represent materials of possible economic importance that occur in geological or physical environments that have not been successfully exploited for the particular mineral." (van Rensburg, 1983). Chromite-rich rocks worldwide contain high platinum group metal concentrations. This feature is found in ophiolitic sequences, Alaskan-type ultrabasic complexes or statiform intrusions. Association of platinum group metals with chromite has received much attention. The reason for that associa¬tion, however, is not clear. Much has been written about how and where the platinum group metals occur. It is known that they are present in the spinel lattice, as solid solution elements in sulfides and as discrete platinum group minerals. This article outlines the reasons geologists should be looking at lateritic terranes to determine the feasibility of searching for undiscovered, low-grade platinum group metals amenable to openpit, bulk mining. Laterite-saprolite horizons could contain significant platinum group metals and location of anomalous values on the surface and in the weathered profile can lead to discovery.

Jan 1, 1993

By Sol Ribakoff

In 1973, the Subcommittee on Contracting Practices, U. S. National Committee on Tunneling Technology, National Academy of Sciences, under the able chairmanship of A. A. Mathews, Engineering Consultant, now residing at Kaunakokai, Hawaii, undertook the task of developing recommendations for improving the performance of underground construction work, reducing the costs of such work and minimizing the adverse atmosphere in which owners and contractors were performing their respective functions. The author of this paper and C. F. Palmetier, a highly qualified engineer, were thereupon appointed as staff assistants to the Subcommittee, to conduct a study of existing practices and relationships in Western Europe and in the United States, to formulate recommendations, for consideration by the Subcommittee and the participants in a future workshop, as to desirable improvements in United States contracting practices and relationships. The study, conducted during 1973 and 1974, involved personal interviews of a total of 162 owners, engineers, contractors, lawyers, and educators throughout the United States and in 7 European countries, the analysis of 178 replies to questionnaires sent to individuals and firms involved directly or indirectly in construction, and a workshop, near Napa, California, attended by 53 representatives of all segments of the construction community. The resulting report, entitled "Better Contracting for Underground Construction", was submitted by the Subcommittee to the National Academy of Sciences, which approved its publication in 1974 by the National Technical Information Service. It may be obtained from that Service at Springfield, Virginia, 22161, as Accession No. PB-236 973. It was recognized-during the course of the study that while contracting practices and owner-contractor relationships were the

Jan 1, 1981

By Ora H. Rostad

Veins containing silver and gold values, with some associated values in copper, lead, and zinc, were discovered in 1890 by Will Kirwin in what was later designated the Kirwin mining district situated on the North Fork of the Wood River, about 56 km (35 miles) west of Meeteetse. (See Fig. I.) After considerable prospecting activity, including the driving of several short adits on veins, most of theclaims in the district were consolidated into two ownerships. One was held by the Galena Ridge Mining Co. which was organized on Nov. 18, 1902. The other was held by the Shoshone Mountain Mining Co. which was organized on Mar. 23, 1903. During the period from 1903 to 1907 inclusive, the two companies continued exploration on veins in their respective areas. The major exploration-development activity for the Galena Ridge Mining Co. was the driving of the Galena Ridge crosscut adit for 709 m (2327 ft), to cut veins at depth which had been explored by short adits high on Galena Ridge. Shoshone Mountain Mining Co. concentrated their work on the Bryan and Pickwick veins. Neither of the companies found ore that was rich enough to sustain profitable operations in that remote locality. Most of the major exploration and development activities were stopped in late 1907. A major snowslide in February 1907 killed three people and destroyed several buildings and may have contributed to discouragement in the area. From 1908 to the early 1920s, only minor exploration work was done. Galena Ridge Mining Co. was dissolved Aug. 5, 1922, and Shoshone Mountain Mining Co. was dissolved on Mar. 23, 1923.

Jan 1, 1991

By G. Barrasso, E. Nordheim

"The European aluminium industry, through its member organisation the European Aluminium Association (EAA), initiated a program on sustainable development for the aluminium industry in 2001. The first step involved the development of a set of sustainable development (SD) indicators for the industry, taking into account of the different interests involved and also the different existing conventions. The indicator set was developed during 2001 and 2002 with the assistance of recognised partners, including Wuppertal Institute from Germany and Versailles University from France. As well, both internal and external stakeholder groups were involved in order to validate the indicators. This has resulted in a set of thirty-four indicators used in the first survey exercise. In the survey the EAA, together with the national aluminium associations, attempted to cover all European plants producing alumina, primary aluminium, rolling ingots, extrusion ingots, foil and recycled aluminium -covering approximately 800 plants. The survey used two points in time, 1997 and 2002, in order to start developing a trend for the individual indicators and to measure progress over time. The industry response to the survey was very positive, with a total industry coverage based on tonnage reported of over 80% for 2002 data and 70% for 1997 data. The results also show a solid progress for most indicators and particularly for social indicators such as training performance, community involvement and employees health programmes. The EAA is committed to conducting this as a regular exercise and is engaged in a number of stakeholder workshops in order to present the survey results, to review the indicators used and to also consider adjustments of these based on feedback from stakeholders and experiences from the first data collection."

Jan 1, 2005

By I. H. Keith

INTRODUCTION The following papers describe the extraction of nickel in the form of ferronickel from the Dominican laterites. The Falconbridge process was developed initially in the Falconbridge Metallurgical Laboratories and subsequently in several successive stages of pilot plant operation in the Dominican Republic. In the course of this work we came to believe that there is advantage in piloting on site. Mining, metallurgical and geo-political considerations all have major impact and that belief has been borne out by commercial plant experience. Lateritic nickel ores differ substantially, even within the same orebody, in their amenability to extraction methods. The Falconbridge process takes account of the heterogeneous nature of the deposit. Three years of geological field exploration led to ten years of process development after it was realised that the then known metallurgical processes would not give economical extraction from the Dominican ores. In addition to establishing the viability of a novel pyrometallurgical approach, it was necessary to verify design parameters for a very considerable scale-up to prototype commercial operation. The plant was eventually constructed within the original estimates of time and cost. Unique features contributing to the technical and commercial success of the project are described. Additionally, some bold extrapolation based on pilot plant work, eventually proved to be quite conservative. The mine is not a conventional open pit operation, but is perhaps better characterised as an earth moving job. Novel application of mobile equipment led to great flexibility in the mine, where operation of several mining fronts is essential to maintaining uniformity of ore feed to the plant. The practical aspects of almost total acceptance of the oversize run-of-mine material through a high-capacity unit,

Jan 1, 1979

By Miroslav Cervenka

The Coal, characterized by coal quality parameters as for example, ash content (Ad), moisture (Wrt), heat content (Qr1), sulphur content (Sd) and other parameters is still in many countries the basic source of energy. Energy is life, especially in modern society, where the demand for ecologically clean energy is very high; and therefore, there is great importance in effective coal utilization Direct utilization - burning of coal for energy generation, is still one of the most effective methods. In most cases, it is one of the cheapest energy transformation methods in spite of the fact that this energy transformation is connected with the deterioration of our surroundings. Deterioration can be substantially reduced if the burning of coal at power stations, heat power stations and other coal consumers is optimized. That means the burning is done in steam boilers, the technical state of which is very good; the coal has minimimum .variations with respect to the projected values; and the burning process is controlled and checked not only from a regulation point-of-view but also from an ecological point-of-view. The instrumentation capable of measuring the characteristic coal quality parameters in real time exists and it forms the basic assumption for the work our research team has made. The proper application of this instrumentation is able to provide information for burning process optimalization. It is the main topic of this paper, which is the compilation of the information on our work -made during the last five years. The whole information is based on practical experience and applied systems in Czechoslovakia in the mines and power engineering industry. See [Cervenka, 1989]

Jan 1, 1992

By Richard R. Klimpel

INTRODUCTION The purpose of this paper is to summarize the current status of reagents used in the mineral industry plus present some current challenges and possible new technologies of the future. Table 1 lists the important families of reagents which, when taken together, constitute at least 95% of the current commercial reagent market. A very approximate estimate of the free world reagent market size in mineral applications is about 1.5 to 2.0 billion dollars (U.S.) using 1985 data. Obviously, to serve such a large market requires the effort of many different types of commercial supply sources. It is estimated that there are over 300 industrial firms in the free world that have a dedicated business/technical structure for supplying reagents related to the mining industry. There are a number of characteristics which are associated with the product families listed in Table 1. Understanding these characteristics helps to provide a realistic economic/technical basis for outlining future challenges in mining chemicals. 1.Essentially all of the products listed are old chemistry in the sense that the molecules have been known and manufactured for at least 25 years. This has not been a highly dynamic field of endeavor from the viewpoint of new product introduction. 2. The greater majority of the products listed can be viewed in commercial terms as "commodity" chemicals, that is, they are available from many sources and the pricing of a some- what generic product generally dominates differences in product quality or uniqueness. With commodity pricing, reagent suppliers significantly reduce research expenditures, loosen product quality somewhat if the applications of the reagents allow, etc. in order to be cost competitive.

Jan 1, 1989

By d&apos, L. R. Fletcher, Andrea. D. V., M. A. Peltier

The Bureau of Mines analyzed coal mine blasting accident data obtained from the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The data were examined to determine the causes, frequency, and severity of accidents in an effort to point out the most dangerous aspects of coal mine blasting. Accident data for the 14 years from 1971 through 1984 show that there has been a total of 43 fatal and 926 nonfatal blasting accident victims in surface and under- ground coal mining. This is an average of 3.1 fatal and 66.1 non- fatal injuries each year. Underground coal mining accounted for 60.5% of the fatal and 78.7% of the nonfatal accidents involving explosives and breaking agents in coal mining. In addition, since 1970 there have been 53 fatal and 20 nonfatal injuries that occurred when explosives were the ignition source for dust and/or methane explosions in underground mines. Abstracts from 297 accidents that occurred from 1978 through 1984 were also examined to determine accident causes. Most accidents occur during scheduled blasting, and failure of the blast area security system is the leading cause. Blast area security problems in surface mining are failure to clear the blast zone, failure of personnel to follow instructions, inadequate guarding, and failure to retreat to a safe location and/or take adequate cover. Other common causes in surface mining include premature blasts, excessive flyrock, and misfires. In addition to the above causes, accidents in underground coal mining can be due to rockfalls triggered by the blast, unexpected breakthroughs, fumes, and incidents associated with Airdox-type systems.

Jan 1, 1986

By D. J. Kennedy, A. W. Stokes, W. G. Klinowski

Sulphur hexafluoride (SF6) has become an accepted standard in the field of mine ventilation tracer gas studies. It has a wide variety of uses for defining mine ventilation flows that cannot be adequately described using conventional instruments such as anemometers and smoke tubes. The Cape Breton Coal Research Laboratory (CBCRL), Energy, Mines and Resources Canada, has been using SF for the past 4 years and has developed numerous release and sampling systems to increase its versatility. The CBCRL has also completed a successful field trial of an automated rapid sequential SF6 analyzer (which gives a pseudo real-time readout) that can be used underground. In doing this work, the authors recognised the potential of being able to use more than one tracer gas simultaneously in an underground study. Two alternative tracer gases (Freon-13B1 and Freon-12) have already been used by CBCRL in some of their underground work. These gases can be measured by gas chromatography utilising an electron capture detector in a similar manner to SF6. A description of these gases, the methods for 6' their handling, release and sampling are given in this paper together with a brief outline of the analytical system used to measure them. Their suitability to mining applications is compared with SF6. A study in which these three gases were used together is discussed and the results and conclusions given. Some of the additional uses for multiple tracer gases to assist the mine ventilation engineer in resolving problems and improving his day-to-day monitoring are discussed. Finally, a brief analysis of developments which can be expected in the near future is outlined.

Jan 1, 1987

By Jeong-Heum Kim, Jan M. Mutmansky, Y. J. Wang

The simulation of randomness in a system of components is important in certain types of systems analyses. This paper presents procedures for generating ventilation networks that are random in many of their characteristics and which can be used to study the performance characteristics of various mine ventilation network analysis procedures without introducing undue bias as a result of the nature of the network. Among the parameters of a network that affect the efficiency of a network analysis procedure are: (1) the interconnection pattern of airways, (2) the distribution of resistances in the network, (3) the number and location of fans, (4) the fan characteristic curve, (5) the size of the network (number of branches), and (6) the density of the network (number of nodes compared with the number of branches). In the procedures proposed here, a single fan with a fixed characteristic is used to simplify the problem and eliminate the fan as a source of variation. The resistances of the airways, the pattern of interconnection of the airways, and the fan location are randomly chosen in an attempt to eliminate the bias in the performance characteristics of the network analysis methods caused by these parameters. A method of generating biconnected networks while keeping the "randomness" of these other parameters is suggested. At the same time, the size and the density of networks are controlled to investigate their impacts on the performances of the network analysis procedures. The combination of these two variables has been termed the "level of complexity" of the network in this paper. Finally, a summary and conclusions section outlines some characteristics of the networks generated, using the random generation procedures outlined in the paper.

Jan 1, 1991

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By O. F. Brown

The use of quality materials (aggregates and asphalt binder) in optimal proportions is the key to producing optimally performing hot mix asphalt (HMA). The Superpave mix design standard in the US introduced specific volumetric and binder property requirements in HMA design. Different methods for HMA constituent proportioning have been proposed in various guidelines. The design process to determine the HMA blend is currently iterative and engineers rely almost exclusively on experience. This approach is time consuming and often does not result in cost-optimal HMA mixtures. This paper introduces a mixed integer linear programming (MILP) optimization model for hot-mix asphalt constituent proportioning. The MILP model minimizes the total mix cost while satisfying all the volumetric, binder and mix property specification requirements. The model has been successfully validated with real-life example. The aggregates and binder ratios from the model were in close agreement with those from the contractor. The Bailey ratios and the gradation constraints were also satisfied. The cost of the optimal mix was $0.804/Mg less than that of the contractors?. This marginal reduction might make all the difference in an industry that is highly competitive. The MILP model also demonstrated that adding RAP to the contractor?s design would reduce the cost of the blend by $5.74/Mg. The virgin binder content was reduced by 1% because of the recycled asphalt contained in the RAP. This work represents the first successful attempt in incorporating both aggregate and asphalt performance requirements into the optimization formulation. Applying these models will ensure the minimum cost mix that meets all constraints and will increase profit margins for plant operators.

Jan 1, 2012

By M. S. Celik

Beneficiation of boron minerals by flotation with well defined systems has been very little investigated in the literature. The difficulty arises from the fact that boron minerals cover a spectrum of solubilities. Colemanite, a calcium containing relatively insoluble boron mineral, and borax, a highly soluble boron mineral have been used to exemplify the flotation of boron minerals. The floatability of both minerals using sodium dodecylsulfonate and dodecylamine hydrochloride exhibits considerable differences in their response to flotation. This has been ascribed to variations in the solubilities 0f boron minerals and the presence of the cations in the lattice structure. Flotation tests along with zeta potential measurements are used to elucidate the mechanisms involved in the flotation of boron minerals.

Jan 1, 1992

By K. Chandrasekaran

Carbon-in-Leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. CIL process is becoming attractive even in other situations when preg robbing is not a factor. This paper discusses the situations in which the CIL circuit can be applied. The results of Leach/CIP and CIL circuits at Newmont's Mill No.2, 4 and 5 are presented for comparison. Newmont's Mill No. 4 was initially designed for a throughput of 4500 tons per day. The mill is presently operating at an average throughput of 7300 tons per day without significant changes to the original design. The design considerations of the Mill No.4 CIL circuit are discussed.

Jan 1, 1991

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By AJIT SWAIN, SUNATI MOHANTY

The ability to predict the dewatering performance of an industrial hydrocyclone from a laboratory-model hydrocyclone is of great importance. In this study, laboratory-scale hydrocyclone experiments were conducted using silica sand samples at 10 percent solid concentration for dewatering with Mozley hydrocyclones with diameters of 2 in. and 4 in. The objective is to predict the design parameters for an industrial dewatering cyclone to achieve higher solid concentration in the underflow. A model was developed based on the Nageswararao hydrocyclone model with the help of a commercial simulator for a hydrocyclone operating at 100 t/h and 20 percent solid concentration to achieve 80 percent solid recovery at 45 percent solid concentration in the underflow.

Mar 1, 2023