Search Documents

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By Peter J. Tarkoy, Terence G. McCusker

INTRODUCTION The discovery of oil and gas reserves in the North American Arctic has led to substantial thought being given to their development. Systems adequate for exploration are not always, or even often, suitable for permanent installations. Combinations of offshore pipeline, drilling ships, platforms, sub-sea systems, sand islands and -ice island bases have been proposed. However, conditions in the Arctic are such that these methods may be difficult or impossible to implement. Problems exist with (1) the freezing of the Arctic Ocean surface for 9 - 10 months per year, (2) the movement of sea ice, (3) scouring of bottom sediments by ice islands and icebergs to great depths below the ocean bottom and (4) deep water channels. Any method which can avoid the problems associated with surface construction in these very adverse conditions merits detailed examination. One of the proposed solutions is to tunnel from a convenient or available access point to a point within the field, construct a chamber large enough to accommodate the drilling equipment and drill the development wells in a protected environment. Service and delivery lines would use the access tunnel and further tunnels and chambers would be constructed in a radiating pattern to develop the whole field. In order to determine the feasibility of underground construction in the North American Arctic, it is first necessary to understand the geologic and environmental factors which would affect such construction, to be knowledgeable concerning the problems and then to consider the techniques appropriate to the conditions which will be encountered, bearing in mind the need to minimize both con-

Jan 1, 1976

By L. G. Tejada, T. Sjursen

In the production of ferronickel at Falconbridge Dominicana's plant in the Dominican Republic the Reduction Plant plays a vital role by partially reducing the nickeliferous oxide ore, and pre- heating the charge to the electric furnaces. Ore is agglomerated in the form of pillow-shaped briquettes which are screened and fed to 12 open-top shaft furnaces. Hot (over 1250°C) reducing gases are partially cooled (less than 1150°C) and introduced through a set of primary tuyeres. The reducing gas rises counter-currently to the flow of solids. A portion of the partially spent reducing gas is withdrawn at the furnace top and recirculated through a set of secondary tuyeres, 1800 nrm above the primary tuyeres. Together with the recycle gas a controlled amount of air is also added to react with the partially spent reducing gas in order to preheat and dry the charge in the upper part of the shaft furnaces. The calcine is discharged through three discharge legs and pusher block assemblies into open-top refractory lined cars. These cars are then hauled to the electric furnace, parked over selected feed ports, and discharged through bottom gates. The furnace exhaust gas is de-dusted in cyclones and then passed through Venturi scrubbers. The slurry is fed to a thickener, filtered, and recycled to the ore receiving hopper in the ore preparation area. Dust generated throughout the plant is collected, wetted to conform with briquette press feed, and recirculated in a controlled manner through the feed system.

Jan 1, 1979

By Jerry Motz, Gary Beerkircher

Through a joint development program between Bougainville Copper Ltd. and Nordberg, the MP1000 cone crusher was developed and tested during the period between 1982 and 1987. Following the successful prototype work, Bougainville Copper purchased an additional three units. A second prototype was installed at Codelco's El Teniente three-stage crushing installation in 1987. This unit has also completed its test period successfully. Three additional units have been sold, making a total of eight, to date. Two will be installed as secondary crushers in two separate large aggregate plants. The first unit installed in the United States was placed in operation at Vulcan Materials Company's plant in Manassas, Virginia in early May 1990. Another unit is being installed in Asarco's Ray Mines expansion. The Asarco installation will be a SAG MILL pebble crusher producing approximately 600 STPH of nominal 1/2" product. Application Objective The objective was to design a crusher that would fit on an existing 7' foundation with minimum modification and yet be capable of twice the production of a 7' cone crusher. In meeting this objective, the power rating was increased to 1000 HP, the maximum design crushing force was increased and the crusher was designed to operate at higher speeds than an equivalent size Symons cone crusher. The MP1000 was also designed to operate with a head throw that can be greater than the equivalent Symons design. Design The crusher design criteria involved the recognition of the crushing force increase required for the finer crushed products than

Jan 1, 1992

By John O. Marsden

Technology development has played a crucial role in the minerals industry throughout history. The development of new technology allows mankind to produce metals and minerals at progressively lower cost of production in real terms, and therefore at progressively lower prices, improving their availability, accessibility and utilization worldwide. However, the developers of such technology are not guaranteed to reap the benefits from this effort: There is an expectation that technology developers will gain an advantage over their competitors. Is this a short-term benefit that results from a temporary cost or efficiency improvement, or is it a sustainable longer term "edge" that prevails even after metal or mineral price has been eroded by the implementation of a major step change technology? This issue is examined by reference to several case study examples in the copper industry. BACKGROUND The development and adoption of new technology has played a crucial role in the commodity minerals industry throughout history. As new, cost-efficient technologies are commercialized, the cost of production decreases, and this enables lower grade ore to be processed profitably. This in turn increases the availability and supply of the metal or mineral of interest, and ultimately (in a free market environment where the supply- demand balance determines price) inevitably decreases the metal or mineral price. This leads to the question: Why should mining companies invest in (new) technology development if the result is a decrease in the product price? The answer is to achieve competitive advantage, where the application of new technology enables one or more

Jan 1, 2004

By L. F. Barrett, D. E. Cameron, J. C. Wilson

Exploration by Anaconda Minerals Co. in the Rico area from 1978 through 1983 resulted in dis¬covery of the Silver Creek molybdenum deposit. The drill-indicated resource is 40 Mt (44 million st) of 0.31% Mo, and projections suggest that the deposit may exceed 182 Mt (200 million st). No source intrusion has been intersected by drilling, but its presence is sugested by intramineral silicic alkali-alaskite porphyry dikes observed at the surface and in drill holes. Age dates and fluid inclusion studies indicate that the deposit was formed 5.2 ± 0.2 m.y. ago and that more than 1200 (3937 ft) of cover has since been removed by erosion. The deposit is hosted by Precambrian quartzite and greenstone, and Paleozoic sediments. Three prominent faults intersect in the vicinity of the molybdenum deposit, and one of these, the Last Chance fault, strongly influenced the shape and location of the deposit. The juxtaposition of host rocks across the Last Chance fault reflects significant offset spanning at least three different periods. Wallrock alteration associated with the deposit includes potassic, phyllic, and propylitic zones in noncalcareous rocks and garnet and anhydrite-diopside zones in the carbonates. All +0.2% Mo mineralization is within the potassic and garnet zones. Premineral faults that intersect the deposit contain the only surface molybdenum, tungsten, and fluorine anomalies. Dispersion halos of the indicator elements were defined by drilling in the discovery phase of exploration, and are particularly well-developed in the hanging wall of the Last Chance fault.

Jan 1, 1987

By Donald D. Born

Mine No. 95 is located in Harrison County about 5 miles west of Shinnston, WV, with coal properties covering the northwest corner of Harrison County and the southwest corner of Marion County and with adequate Pittsburgh seam reserves to support the mine for many years. The mine was opened in 1967 and was planned, projected and operated as a room and pillar mine. It is located on a spur branch of the Baltimore and Ohio Railroad, has rail loading facilities and shipped by rail during its development stage. In 1972 it was converted to a mine mouth power station supplier and now transports coal by conveyor belt directly to the Harrison Power Station of Allegheny Power System. In 1971 the first longwall unit was installed in a selected area of the mine and immediately an orderly system of planning was developed to overcome the restrictions associated with longwall mining. The first was the development of the technique necessary for the plugging of abandoned oil and gas wells that existed in the area. With the assistance of the Morgan- town Energy Research Center of the Bureau of Mines, this restriction was overcome and thus opened a great potential for longwall mining in northern West Virginia. Other restrictions that had to be considered for longwall planning were dwellings and other improvements, snap top zones, water courses, and adequate bleeder systems, and the handling and treatment of mine drainage. In 1975 the second longwall unit was installed and soon therefore became a total longwall mine.

Jan 1, 1986

By J. McMurray

Introduction Uranium was recovered from mining of collapse breccia pipe deposits in the Arizona Strip district in northwestern Arizona (Figure 1) intermittently between 1956 and 1990, with cumulative production having totaled 23.3 million pounds of U3O8 (8960 tU) at an average grade of 0.6% U3O8. Production was suspended in 1990 because of low uranium prices, but the recent resurgence in market price once again makes the breccia pipe deposits potentially attractive exploration and development targets. This paper describes: (1) formation of the pipe structures and their metallogenesis; (2) mining and milling of breccia ore; and (3) potential roadblocks to development of new breccia pipe mines. Breccia Pipe Formation Formation of the breccia pipes began in cave systems formed during development of karst topography in the Mississippian Redwall Limestone. The karst Redwall surface was eventually covered by up to 900 meters of shallow marine to continental sediments ranging in age from Pennsylvanian to Triassic. The pipes were formed by progressive upward stoping caused by groundwater ascending under hydraulic head along near-vertical faults, joints and fractures. The stoping process involved both chemical disaggregation and mechanical failure of roof and wall rock. Upward stoping of successively younger units allowed for upward propagation of a pipe and resulted in a chimney-like column of breccia between the steep walls of the pipe. Syndepositional thickening of sedimentary units of varying ages indicates that pipe formation began as early as early Pennsylvanian time and continued intermittently through Triassic time.

Jan 1, 2007

By Syd S. Peng

According to accident statistics (l, 2), roof fall accidents occur quite frequently at the intersections of underground? openings and account for up to 30% of the roof fall fatalities. But this figure will certainly go up considerably if roof falls not associated with any fatal accident are included in the analysis. Unfortunately, nonfatal roof falls are seldom documented. In the underground coal mines, there are two types of entry intersections. One is the three-way (V type) and the other is the four-way (T type) intersections. A three-way intersection occurs whenever the mainline track haulageway turns at an angle into a section haulageway. The four-way intersections by far the most common type in the U.S. under-ground coal mines are formed by the intersections of two entries which are oriented perpendicular to each other or by the intersections of entries and crosscuts. However, crosscuts are frequently driven at an angle to the entry to facilitate machine movements. The four-way intersections formed by this method of crosscut development are angled. At the intersection of two underground openings, the diagonal roof span is wider than the width of each individual opening. This is one of the major reasons why roof falls occur more likely at the intersections than in the entry between pillars. Consequently, special intersection support plans are usually employed (Figs. 1 and 2) for intersections. The most popular practices are to decrease roof bolt spacing 1 ft. less than or to increase roof bolt length 1 to 2 ft. longer than those employed in the entry between pillars (3). The increase in bolt length or decrease in bolt spacing can be applied to all of the bolts in the intersection or employed only for the strategically located bolts depending on the individual mine practices. These rather generalized practices seems to be adequate for some areas but in many cases inadequate for others. Occasionally, the neighboring two lines of chain pillars are staggered such that the crosscuts in one row of chain pillars face the centers of the chain pillars in the neigh-boring rows. This layout forms T-type three-way intersections which are also inadequate for most weak roofs (3, 4). A study was therefore initiated to develop special techniques for intersection supports. The first phase of the study was the analysis of the stress fields for the underground entry intersections. A three-dimensional stress analysis was necessary for this purpose. Unfortunately, the three-dimensional problems of complicated boundary conditions are beyond the existing analytical methods. The three-dimensional finite element method (FEM) was therefore employed in this study. In the analysis, square pillars of 40 feet wide and an entry height of 8 feet were assumed while entry widths varied at 14, 20 and 26 feet. This model was selected to simulate the mine where roof falls data were collected. The second phase of the study was the collection of field data. The sizes of the roof falls including heights, lengths and widths were collected and analyzed. In the third phase study, the results of the first and second phases were compared and discussed. The analysis of field data revealed an arching zone within which roof falls occurred. The arching zone above an entry obtained empirically was compared with the calculated stress contours. Assuming that the bolts must be anchored in the rock strata outside the arching zone, the preferable systems of bolting were proposed. Also the amount of pretension required to inhibit sliding between layers was discussed.

Jan 1, 1978

By C. J. Pritchard, R. D. Jacksha, K. V. Raj, C. Sunderman

"In underground metal/nonmetal mines, repeated short-term exposure to high levels of airborne contaminants can become a serious health issue. Currently there are no common mechanisms to control or mitigate these localized short-term high exposures to contaminants. To improve miners’ health and safety, the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD) is developing a Smart Monitoring and Control (SMAC) system for real-time monitoring of mine air quality, with integrated countermeasures to reduce these high concentrations of airborne contaminants in localized sections of mines. To develop and test a SMAC system that could be implemented in an underground mine, researchers at SMRD built a test apparatus incorporating a fan, louver, ducting, and sensors combined with atmospheric monitoring and control software. This system will institute effective countermeasures to reduce contaminant levels, improving miner safety and health. INTRODUCTION Underground metal/nonmetal mines continue to expand production by employing large equipment in greater numbers and by mining into hotter and more challenging environments which are typically further away from fresh air sources. This challenges the ventilation system to provide adequate quantities of fresh air to the workplace and increases the potential for air contamination that could result in immediate and long-term health and safety issues to miners. Currently, airflow and contaminant concentration in mines are typically based on full-shift sampling which may not identify repeated short-term exposures to high levels of airborne contaminants such as NO2, CO, diesel particulate matter (DPM), and dust with high silica contents. Repeated short-term exposure to these high levels of airborne contaminants over long periods can lead to serious health issues which are documented in several studies [1-3]. Based on data from ventilation surveys and contaminant measurements, mines often attempt to minimize exposures by sending more fresh air to the working areas where contaminant concentrations are found to be high. Real-time monitoring and control allows mines the option to monitor contaminants and implement controls in real-time. Real-time monitoring and control of the underground mine atmosphere has been a subject of research since its beginning in Finland at Outokumpu’s Pyhäsalmi Mine in 1969 [4]. More recently, the real-time monitoring and control problem has been addressed using ventilation on demand (VOD) systems [5, 6]. A VOD system attempts to deal with this issue on a global level by controlling fans, louvers, and doors to increase airflow to active work areas and reduce contamination. However, a VOD system only controls the distribution of airflow and may not be helpful in mines where the airflow is at maximum capacity. Researchers at SMRD are developing a SMAC system for real-time monitoring of mine air quality with an integrated ability to trigger countermeasures to reduce high concentrations of airborne contaminants in localized sections of mines. The SMAC system will be designed, tested, and refined in the laboratory environment before being demonstrated in an underground mine. This system will not only try to minimize the gaseous contaminants by regulating the airflow locally, but will also potentially employ a filtration system to reduce the airborne contaminants in case the maximum airflow capacity is reached. This paper presents development of the test apparatus for the SMAC system."

Jan 1, 2017

By Steve O. Green

Introduction The US coal mining industry is in the midst of a serious economic crisis. To overcome increased operating costs, operators must take advantage of technological advancements in mining systems and equipment. A relatively new concept available to underground operators is that of extending the cutting depth for continuous mining machines (continuous miners). This system is referred to as deep-cut mining, and may be described as mining cuts to depths greater than the standard 6 m (20 ft). Productivity is increased through the reduction in continuous miner tram time since the machine stays longer in each working face. To successfully implement a deep-cut mining system, three problems must be overcome: Exposing personnel to unsupported roof, methane removal, and controlling respirable dust. Remote control cutting The solution to the unsupported roof problem is remote control. Recent advances in remote operation, especially in radio remote controls, have resulted in what is generally accepted as a safe and reliable tool. By installing remote control on the continuous miner, the operator and helper can now be stationed in a supported area. This allows for improved visibility while cutting coal. With this in mind, the limiting factor now becomes the position of the haulage equipment operator. North River No. 1 uses Joy 21SC shuttle cars and Jeffrey 4110 diesel ramcars. These cars are pulled against the bumper of the continuous miner. Thirteen meters (43 ft) can be cut with the shuttle car and 14 m (45 ft) with the Ramcar before the operator of the car is inby permanent supports. By loading away from the bumper, about 1.5 m (5 ft) can be added, bringing total cut depths up to 14.5 and 15 m (48 and 50 ft), respectively. Methane removal The second problem involves methane removal, and the line curtain-to-face distance. In other words, how to maintain the line curtain to allow sufficient ventilation to remove methane and not expose workers to unsupported roof. The solution, in most cases, is to use a blowing-type ventilation system. Unlike the exhausting system that, to be effective, must be installed within 3 m (10 ft) of the working face, the blowing system can be effective at greater distances from the face. Numerous studies have documented the advantages of a blowing-type ventilation system over an exhausting system. Furthermore, a blowing system can be significantly improved by in¬creasing the velocity of the air delivered without increasing the volume of air. With this greater ventilation efficiency, it is possible to secure ventilation plan approval from the Mine Safety and Health Administration (MSHA) for a greater curtain set-back distance. This eliminates the need for personnel to travel inby permanent supports to extend the face brattice. The distance from the face MSHA will approve, however, is on a mine-by-mine basis. MSHA will evaluate the particular mine's face methane liberation rates, along with the specific proposals regarding face ventilation volumes and velocities. Dust control The third problem is controlling respirable dust. This is actually a result of the solution to the second problem. In the blowing system, while mining on the slab cut, both the continuous miner and haulage units are located on the dusty side of the line curtain (Fig. 1). In the early 1970s, underground operators virtually abandoned this system, in order to comply with the 2 mg/m3 (0.87 gr per cu ft) federal dust standards. The blowing face curtain did offer increased face ventilation efficiency. With that, greater curtain-to-face distances were also

Jan 8, 1987

By Barrie Butt, V. S. Znamensky

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development, and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made, and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been- in progress for seven years and the writer of this chapter has been intimately associated with the project during the five years of exploration and seven years of exploitation. The Woodsreef mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and fiber. Because of the latter feature, much research has been undertaken by Woods- reef and other scientific organizations in Australia, England, and Canada regarding the Woodsreef fiber. The answers to some of the problems have negated some accepted concepts of asbestos ore milling and led to the development of new techniques. Some of these new techniques include the adoption of microscopic fiber counts as a routine procedure, the modification of accepted evaluation procedures, the development of new machines for dedusting fibers, and the recognition of a fiber with a unique milling behavior pattern and, possibly, properties. The problems experienced can be broadly divided into those associated with the geology and the physical properties of the fiber. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognized during the exploration stages, a feasiblity evaluation may be just a little closer to the actual. The Woodsreef chrysotile asbestos deposit (latitude 30°24' S, longitude 150°44' E) is located 80 km north of Tamworth, NSW, Australia. The mine has been in production for six years and has a present scheduled mining rate of 33.11 Mt/y. An eight rock line mill treats an average of 7000 t/day, after beneficiation, and yields fiber grades in the range of group 4 to group 6 with some floats. The estimated re- serves of 30.56 Mt, with an ore to waste ratio of 1:3.0, are contained in two main zones that are designated the North and South zones. Mining started in the South Zone in 1972 and then, be- cause of the higher ore value, moved to the North Zone in 1975. Presently, there are two distinct open cuts referred to as the South and North pits that will eventually be worked together. The Woodsreef mine is owned by Woodsreef Mines Ltd. and is operated by Chrysotile Corp. of Australia Pty. Ltd., and is one of only two producing asbestos mines in Australia. The second mine is at Baryulgil, (latitude 29°13' S, longitude 152°37' E), and is operated by a subsidiary of Woodsreef Mines Ltd. This operation produces about 500 t/y for a captive market. An exploration program is being conducted in the area surrounding this small producer with a significant degree of success. The concepts developed during the exploitation of the Woodsreef deposit are being incorporated in the evaluation of the Baryulgil area, and if the Baryulgil deposit proves to be eco- nomic it is hoped that this approach will eliminate some of the major crises that have beset the production at Woodsreef during the first four years of operation. The purpose of this chapter is to describe the Woodsreef deposit, and more important, to

Jan 1, 1986

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By R. Addison

This is the story of the Carlton Mill. But first-a little geography. For those who do not know where the Carlton Mill is, or, perhaps, have only a vague idea, its location is indicated in Figure 1. The plant is situated on the road between the two old mining towns of Cripple Creek and Victor, 10 the west of Colorado Springs. From Denver, it's about 110 miles by road. The story of the Carlton Mill began with the discovery of gold at Cripple Creek in 1890. This discovery set off a major boom such that, by the turn of the century, there were 450 separate operating mines in the district. Gold production boomed early and declined rather rapidly as indicated by the graph in Figure 2. Significant factors affecting production are shown on the graph-the raising of the gold price in 1934 from $20.67 to $35.00 per ounce and the government executive order L-208 in 1942 requiring the closure of all gold mines.

Jan 1, 1983

By Igor Gonzales G.

Southern Peru Copper Corporation (SPCC) has recently completed the construction of copper leaching, solvent extraction, and electrowinning facilities at their Toquepala and Cuajone plants in Southern Peru. Much of the ore for these new operations is the result of the existing mining operations that have been in existence as early as 1959. At Toquepala, pre-conditioning and bacterial dump leaching of the sulfide ore that was too low in copper content to be processed through the copper concentrator began in 1987. The Cuajone heap leach operation is treating copper oxide ore that has been stockpiled since the Cuajone concentrator began operation in 1976. The pregnant leach solutions from the dump leaching at Toquepala and the permanent pad heap at Cuajone are combined into one plant feed solution. Adjacent to the large dumps at Toquepala, a solvent extraction and electrowinning facility has been constructed. The electrowinning facility has a planned annual production rate of35,000 metric tons per year Grade A cathode copper. Initial production of the cathode copper began in November 1995.

Jan 1, 1996

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By Manoj Kumar, Anil Kumar Singh, Prabal Patra, Ashish Agrawal, Souvik Ghosh, Subhashis Kundu, Kamma Ramakrishna Rao, Manish Kumar Gupta, Anindya Sarkar

The slag measurement systems in the cast house are very important. In the conventional method, the slag is granulated in a slag granulation system, and the slag flow rate is measured by the associated belt scale. However, in places where a slag granulation system is not available, the alternate approach is to deduce a theoretical calculation and develop the measurement because the commissioning of such slag granulation requires huge capital and has inherent geographical limitation. However, the theoretical approach suffers from several drifts and is far from the reality. In the present paper, we have innovatively engineered a sensor by designing the stellite-coated thermocouple that can measure the temperature of the slurry and placed it in such a way that the abrasive slag granules do not obstruct it, but we could measure the temperature of hot water, and further based on the thermodynamic approach, the slag flow rate is determined that can be compared with the theoretical approach. This approach of slag rate measurement is cost-effective and long-lasting.

Oct 2, 2023

By Ayman A. El‑Midany, Hassan E. El‑Shall, Kerri‑Ann A. Hue

Modification of clays is necessary for the zearalenone (ZEN), as long-chain mycotoxins, removal. The organic-cations were usually used to modify the clay hydrophobicity to accommodate the large mycotoxin molecules. In this study, tri capryl methylammonium (TCMA) chloride and common corn oil were used in clay modification. Several characterization techniques such as XRD, FTIR, and TGA were used to identify the d-spacing changes after modification either by TCMA or corn oil. The results of applying the TCMA-corn oil-modified clays in ZEN removal indicated a noticeable improvement where more than 90% of ZEN could be removed in vitro at acidic and neutral pH values. The success of eliminating a high percentage of ZEN molecules is due to the expansion of intergallery spacing as a result of TCMA surfactant intercalation within the clayforming layers. The removal percentage does not depend only on pH but also on the amount of clay used. In addition, the ZEN removal in the presence of corn oil is better at acidic pH and small clay amount where the ZEN can be fully removed.

Sep 27, 2021

By Omar. M. Arafat, Edgar Pérez, Kyle. M. Bartholomew, Robert. E. McIvor

The “circulating load” confounds understanding of ball milling circuits. Conflicting opinions exist as to its role. Should it be high, or low? Why does it even exist? It is commonly accepted in the plant as a given, the outcome of largely unknown factors. As such, it may often go unmeasured or even ignored. This paper describes the importance of the circulating load in wet ball milling circuits. It is characterized not only in terms of solids mass flow (or ratio of mass flows), but also by its other key physical characteristic, its size distribution. Its effect on grinding circuit performance is explained. The equipment application design steps to achieve a desired circulating load, in terms of both its mass flow and size distribution, are described. Finally, its pivotal role in grind control is specified. Our goal is for the reader to come away with a fresh understanding of the role of the circulating load in wet ball milling circuits, including how and why it should be measured and managed.

Feb 22, 2026

By R. Pakalnis

This paper compiles the research work conducted by the Spokane Research Laboratories in the investigation of shotcrete within underground mines to the applied design of ground support for the operator. It looks at the design methodology in terms of employing shotcrete as a fabric to confine the rock mass between the individual bolts as dictated by empirical charts. The failure mechanism in terms of its implication on design is presented with respect to the design of 6m wide tunnels for temporary and permanent openings within weak rock masses. This is reflected by field observations that relate laboratory tests to the onset of failure for the operator in order to provide guidelines for design and monitoring. This is coupled with guidelines for safe entry in terms of cure times as well as the understanding of the behaviour of the shotcrete in terms of fibres and the overall strengths that result with respect to the design of the mine openings. This enables the operator to better understand his workplace thereby provide a safer work environment.

Jan 1, 2010