Search Documents

By Geoff C. Knight

Longwall mining using the shearer is acknowledged internationally as the most economically successful method of high volume production from underground coal mines. Since its introduction in the 1950s, a great deal has been achieved in developing the capability and reliability of the shearer - and the associated face conveyors and powered roof supports - to produce the competent systems now widely deployed. Equipment will continue to improve as knowledge and experience are gained and through the influence of market forces on the international equipment suppliers. However, current systems are so successful that further improvements are likely to be incremental rather than radical unless a high level of system automation is introduced. The automation concept is not new to the shearer-based longwall system. The opportunity and the need were recognized soon after the shearer and powered support were introduced in the 1950s. In the early 1960s, the British Coal Corp. (BCC; then the National Coal Board) attempted remotely operate longwall systems. Those imaginative early schemes were seen as failures at the time. But, with hindsight, a great deal was learned from the experience that stimulated automation research in several European countries. One of the most fundamental lessons learned was that coalface system automation is not possible until there is a high level of competence in automatically controlling the operation of the production machine itself within the coal seam. Once that is achieved, the rest of the system will follow with comparative ease.

Jan 1, 1991

By John D. Gardner

This paper describes a process which finds the maximum worth of a mineral deposit. The procedure requires two phases. The first uses a microcomputer evaluation model to find the optimum design input, with minimum attention giving to actual mining constraints that might exist. The second phase runs the first-phase design parameters through a direct simulation model on a mainframe computer. In phase one, financial, economic, and geotechnical data are entered; and an idealized list of design parameters is output. The list includes optimum values for cutoff grade, mine life, mine size, paytons, paygrade, and payvalue. In addition, the model generates pro forma operating and cash flow statements and it indicates the maximum net present value (NPV) possible for the deposit along with the probability of that oc¬curring. The initial results imply perfect mining conditions. In phase two, when actual mining selectivity, sequence, and other practical design considerations are related in a direct simulation model to the optimum criteria found above, the maximum NPV invariably decreases. However, if it is still satisfactory (NPV greater than or equal to zero) then the maximum worth/ optimum design have probably been found in the first iteration. If, on the other hand, NPV is now unsatisfactory, then design compromises must be made and simulated, and the results rerun through the evaluation model. If several iterations fail to yield a positive NPV then the deposit is most likely unfeasible t for the forecast economic conditions used in phase one.

Jan 1, 1986

By Marvin Barnes

The Sacaton mine is a relatively new open¬pit copper mine owned by Asarco, Inc., which has been in production only a few years. The mineral deposits consist of two ore zones; a western, near-surface zone minable by open-pit methods, and a deeper eastern zone which will have to be mined underground, probably by block caving. The copper deposits are related to small quartz monzonite intrusives implaced into Precambrian granites. Both rock types act as hosts for the copper mineralization, which has been secondarily enriched sufficiently to constitute ore. In the western zone the enriched supergene chalcocite has been subjected to postenrichment oxidation processes with partial destruction of the chalcocite blanket. The deeper eastern chalcocite zone has not been as severely affected by later supergene processes. Several mineralogical populations are represented in the total copper deposit. Leached capping overlies the chalcocite enriched zone, and in the western ore body there is a very irregular interface between the leached and enriched zone, which is complicated by oxide copper minerals irregularly distributed. Primary lower-grade chalcopyrite mineralization occurs below the enriched zone. When mining commenced near the top of the enriched zone, considerable difficulty was encountered in correlating the actual grade of ore in place with the estimated grade of the mining blocks. The mineralogical complexity and fairly wide spacing of diamond drilling made reliable grade estimation of individual ore blocks a difficult procedure.

Jan 1, 1979

By M. Karmis

Surface subsidence has been recognized as an inevitable consequence of underground coal mining for several centuries. The damage resulting from this phenomenon has been witnessed in rural as well as in urban areas and ranges from simple land settlement to severe structural damage to buildings. Subsidence prevention is not feasible, at least under the existing technological and economic constraints of underground coal mining. Using a rational method of subsidence prediction, it has been demonstrated in many coalfields that subsidence control can be successfully practiced in order to reduce and accommodate subsidence within environmentally acceptable levels. This paper presents the development and testing of a subsidence model, based on the zone area method. This technique is a refined development of the influence functions and it is capable of investigating a mining plan of any shape, thus facilitating both longwall and room-and-pillar mining systems. More specifically, this study can be divided into two major efforts: (a) The development of the zone area model. This formulation was designed to accommodate the analysis of an optimum number of zones, over the area of interest, both accurately and efficiently. (b) The testing of the computer techniques with appropriate field measurements. In order to accomplish this, published as well as unpublished information was collected and analyzed according to a regionalized scheme. This procedure minimized differences in subsidence characteristics between the various coalfields and allowed a regional validation of the predictive capabilities of the model.

Jan 1, 1982

By R. V. Ramani, R. Srikanth

A three-part study was conducted to relate the dust generation propensity of a coal sample, defined here as the dust generation rate (grams of dust generated per tonne of coal broken), to its characteristics, in order to rank coal seams according to their respirable dust generation potential. In this paper, the results of a single breakage study on a variety of coal samples encompassing all coal ranks, and samples from operating mines are discussed. Further, where data are available, the primary dust generation rates of coal samples collected from underground coal mines are compared with the in-mine dust generation rates. The results of this analysis are then used to apply the results of this study to longwall face ventilation design. Vitrinite reflectance, and level of organic metamorphism are highly correlated with primary respirable dust generation rates of bituminous coal samples. The dust generation rates in underground coal mines are an order of magnitude higher than the primary dust generation rates in the laboratory. Depending on the type of coal, production rates, and dust control procedures, the air quantity required for airborne dust control can vary significantly. The air quantities on some high production longwalls are approaching the limits beyond which it may not be possible to reduce ambient ARD concentrations to less than 2 mg/m3 by dilution ventilation alone. In these cases, the miner's exposure should be controlled through the use of personal protective de- vices and administrative practices.

Jan 1, 1997

By D. Constantinides

In 1981 a Zn-Ag-Pb deposit was discovered in the vicinity of Molai, Greece. Subsequently, it was determined to be of the Kuroko type. The geology of various areas in the southeast Peloponnesean Peninsula is similar to that of the Molai deposit. Since favorable geologic criteria are present, absent, or unknown in varying degrees in all areas, it was deemed necessary to classify and rank the prospective areas according to the level of information available. For each level of information, an ore discovery model based on pragmatic exploration criteria was developed, enabling the favorability of occurrence to be calculated for each area. A Monte Carlo simulation was used to calculate the probabilities, the input data consisting of quantitative and qualitative estimates of the geologic criteria for each area. Three levels of information were modeled : Level A consisted of 9 criteria, level B of 12 criteria, and level C of 20 criteria. The three levels of information were tested on the Molai area. The results exceeded expectations, showing the gen¬eral trends which control mineralization at the lowest level of information. With an increase in the level of information, geological trends become more evident and a differentiation can be made between areas containing Cu mineralization, exhibiting a low probability, and areas likely to contain Zn-Ag-Pb mineralization. The models were then applied to the neighboring areas - only level A and B were available.

Jan 1, 1986

By M. J. Richards, T. X. Ren

Determination of the state of an underground fire plays an important role in fire fighting, rescue and reopening operations. This is normally achieved by the analysis and interpretation of fire gases taken from the fire zone. However, drawing conclusions from gas analysis is not an easy task and needs specialist skills, expertise and experience that are usually beyond the knowledge of the officials in a mine. The complexities of a mine fire and the uncertainties of available information often make effective fire fighting decisions difficult if not impossible. This paper describes a knowledge based expert system that can aid in the diagnosis of sealed coal mine fires. Using a commercially available shell, the expert system has been designed to accommodate a series of diagnostic rules replicating the reasoning logic that would be used by human experts. The system allows the diagnosis of explosibility of the fire zone and trends of various fire ratios to be easily visualised for decision making. By continuously analysing the incoming information, the system is able to provide a rapid assessment of the situation of a sealed mine fire prevailing under specific mining and geological conditions. In addition, short term trends in fire behaviour can be predicted and possible fire control actions recommended. An example is given and shows how this system can be used as an analytical tool in various ways to assist the combating of coal mine fires. Further development of the system is discussed.

Jan 1, 1993

The world's largest hydraulic excavator was recently introduced at Syncrude's North Mine at Fort McMurray, Alberta, in Canada. O&K's 826t (910-st) behemoth RH400, with a 42-m3 (55-cu yd) bucket, is capable of loading 72.5 t (80 st) in one pass. Syncrude's Alberta operation is the nation's largest single source of crude oil. It is also the world's largest producer of oil from oil sands. Syncrude produces 205,000 bbl/day, expects to increase production to 225,000 bbl/day by 1999 and to 320,000 bbl/day by 2005. That translates to 73.5 million bbl of Syncrude Sweet Blend (SSB) produced in 1996, 82 million bbl in 1999 and 114 million bbl in 2005. The North Mine is a new development that will replace the current East Mine, to be depleted of oil sand by the end of 1999. The North Mine will feature hydrotransport, a new and unique method of transporting oil sand from the pit to the process plant. Oil sand from the truck-and-shovel operation will be processed through a double-roll crusher and placed in a cyclofeeder where it mixes with hot water. The material is then screened and transported by pipeline to the extraction plant. Hydrotransport will replace conventional conveyor transport for moving raw product from the pit. Mine development will also use two 290-t (320-st) haul trucks to compliment the fleet of existing 218-t (240-st) trucks.

Jan 1, 1998

By R. A. Jankowski, J. J. McClelland

Laboratory tests were conducted by the U.S. Bureau of Mines to determine the respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Exhausting face ventilation was varied from 3,000 to 9,000 cfm (1.42 to 4.25 m3/sec). Spray-water-flow was varied from 15 to 35 gpm (0.057 to 0.132 m3/min), while nozzle operating pressure was varied from 80 to 200 psi (5.62 to 14.06 kg/cm2). Results from gravimetric dust samples indicated that airflow had the greatest individual impact on reducing dust levels, with return and operator concentrations reduced by as much as 57% and 99%, respectively. Interactions between dust control parameters were found to be significant. Often, these interactions defined a level of application for a control parameter where further increases in that parameter failed to produce additional reductions in dust concentrations. In several cases, increases in a control parameter resulted in higher dust levels at the operator's location. These higher dust levels were attributed to additional rollback and/or airflow turbulence. Regression modeling indicated that increases in airflow to 8,400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.84 kg/cm2) typically were beneficial at the operator and return sampling locations.

Jan 1, 1991

By Alan G. Mayton, Jon C. Volkwein

The U.S. Department of the Interior, Bureau of Mines, in cooperation with an American firm, has been contributing toward the creation of a new highwall mining system for extracting coal in active, unreclaimed contour strip mines in the United States. The prototype system features the computer-based, remote control, video operation of a thin-seam continuous miner. Haulage is accomplished remotely also with a 76-m (250-ft) long multiple-unit continuous haulage (MUCH) conveyor system on rubber-tire vehicles. One aspect of this multi-faceted effort has been to design a ventilation system for removing dust generated at the face during the extraction process. The remote mining system eliminates the need for personnel in the mined workings. Ventilation is required to remove visible dust from the area inby two video cameras. These cameras are located approximately 6 m (20 ft) from the face, one on either side of a modified Jeffrey 102HP continuous miner. Removing the dust from this area provides the remote operator with constant visual monitoring of coal extraction at the face and thus, insures the effective operation of the mining system. A ventilation system was designed for use in a mine opening with a maximum cross-sectional area of roughly 4 sq m (44 sq ft) excluding the mining machinery. This paper describes the ventilation system and discusses how it was developed in view of the constraints imposed by the mining equipment, mining conditions, and the extraction process.

Jan 1, 1989

By Christopher J. Hall

It has been known for a long time that summing pressure drops and rises due to friction, shock, fans and natural ventilation is incorrect. In fact, lost works and works should be summed. In spite of this, the traditional method of finding a fan/system operating position has been the H/Q Curve. This paper presents (lost) work/m curves, progressing from a single fan moved around the system to include natural ventilation work, and fans in a series, parallel and series/parallel. The solutions obtained graphically are substantiated by dry air thermodynamic solutions, and the traditional solutions are shown to be in error. This method of solving problems is particularly useful when moving fans around the system, and essential in series/parallel and series situations with substantially different fan densities. The dry air analysis is employed because of its simplicity. Real air, with evaporation and condensation, will react somewhat differently, and one should use real densities (i.e.[l + w +w]/va ) when using this method. One source of error when applying this method to real air, although probably not major, will be investigated in a subsequent paper. Friction and shock losses are proportional to the square of the mass rate of flow, leading to the typical parabolic system curve. However, the unbalanced water stuff potential energy term, on a unit mass basis, is substantially independent of the mass rate of flow. It is possible that this could be handled as a negative natural ventilation work.

Jan 1, 1987

By Y. Wang, E. Forssberg, R. J. Pugh

The coagulation of dispersed ultrafine weakly-magnetic oxide mineral particles (e.g., natural hematite and chromite) in an external magnetic field can be described by interparticle forces. Essentially, coagulation occurs when the short-range London-van der Waals interactions and the long-range magnetic forces outweigh the stabilizing electrical double-layer repulsion. Using the classical colloid chemistry theory, the various components of the potential energy for different-sized particles at a series of ionic strengths and magnetic field intensities were calculated. The results of this theoretical analysis were then related to the results obtained from experimental studies in which the magnetic field-induced coagulation of the ultrafines of natural hematite and chromite in aqueous suspensions were investigated using a laboratory-scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, the maximum coagulation occurred near the pH of zero-point-of-charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, the long-range magnetic forces enabled coagulation to occur in the "secondary minimum." This caused the formation of chains that appeared to be relatively stable during sedimentation.

Jan 1, 1995

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By G. O. Kesse

The Republic of Ghana, located on the West Coast of Africa, is one of the West African countries rich in bauxite deposits. The main occurrences of bauxite deposits are at Sefwi Bekwai in the Western Region, Aya-Nyinahin in the Ashanti Region, Atewa Range near Kibi and at Mount Ejuanema both in the Eastern Region of Ghana. These bauxite deposits belong to the so-called blanket deposits as they are associated with erosion surfaces of old peneplains and occur as cappings on the flat tops of hills or mountains whose heights are generally greater than 600 metres above sea level. These deposits can also be classified as laterite-silicate bauxites since they have been formed under tropical weathering conditions. Genetic and mineralogical investigations have revealed that all bauxite deposits of Ghana are the result of indirect bauxitization processes, for the minerals of the weathering parent rocks have not been transformed directly into gibbsite. In all cases, lithomarge of kaolinitic clay can be recognised. The geology of the major occurrences of bauxite in Ghana shows that the Mount Ejuanema deposit is the only deposit associated with the Voltaian System of rocks. This rock System consists mainly of sandstone, shale, mudstone, conglomerates and pebbly beds. All the otter deposits are associated with the Birimian System of rocks which are made up of metamorphosed lavas,pyroclastic rocks, hypabyssal basic intrusives, phyllites, schists, tuffs and greywackes.

Jan 1, 1984

By David Morrison

On the Corramandel Peninsula of New Zealand, the Waihi Gold Mine has undergone a major redevelopment. The upgrade included the construction of two very large overland belt conveyors, both rated for a capacity of 6000tph. The first of these conveyors (CVR2) traverses a total of 1600m over undulating terrain, including a significant section running through tunnels. A large hill is climbed, just after the mid-section of the conveyor run, before dropping back down prior the discharge point. The second of these conveyors (CVR8) traverses 1100m along an alignment with a horizontal curve, a number of vertical curves and a significant lift before the discharge point. The CVR8 conveyor also included a shuttling head pulley arrangement. The mine they service is inside the town of Waihi. The conveyor alignment runs through the town and out to the metallurgical process site on the outskirts of the municipal area. This paper documents the engineering process that took place in the design of these conveyors. The Martha Hill mine in Waihi, New Zealand is unique. The mine is placed in the township. Consequently there are quite stringent environmental limitations on the mine's operation. In [Figure 1] the proximity of the mine to the town is shown. In the top-centre of the photograph the alignment of the existing smaller overland conveyor can be seen leading from the mine to a tunnel through the hill in the background.

Jan 1, 2000

NIOSH is conducting research to reduce the silica dust exposure of workers at surface coal mines. One goal of this research is to evaluate the relationship between drilling parameters, rock strata and silica dust generation. This study involved measuring blast hole emission dust from a rotary drill rig which required sampling high concentration dust (>400 mg/m3) for silica content in a high velocity airstream. To measure dust initially, traditional sampling methods using personal sampling instruments were attempted in and around the shroud area of the drill with no success. Variations in the dust cloud concentrations under the shroud, the condition of the shroud and its orientation over the hole, and ambient air conditions prevented consistent and accurate dust measurements from being obtained. Amore consistent dust cloud is necessary for accurate measurements. An area of the drill’s dust collector system that consistently draws the emitted airborne dust from the hole is the collector tube. This tube connects the drill collector’s vacuum and dust filtration system to the shroud area. Assuming the collector system is working as designed, sampling from the collector tube would enable more consistent and accurate samples to be taken. However, current personal samplers are unable to sample in the concentrations and velocities experienced in the collector tube, so another method had to be devised. To achieve the desired results, an in-stack cascade cyclone was used. Preliminary field testing shows positive results.

Jan 1, 2003

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in nine states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards (Richmond, 2017).Abandoned mine fires, if left uncontrolled, can burn for years and, in fact, one of the most wellknown mine fires in the United States is the mine fire in the Borough of Centralia, PA, that began on May 27, 1962. Reportedly, officials decided to clean up the local landfill for the upcoming Memorial Day holiday by burning the garbage on the site. Unfortunately, the landfill was located on the site of an abandoned strip-pit mine on the edge of the Borough (Dekok, 2009). The strip pit had been left open after being excavated around 1935 and was approximately 23 m (75 ft) wide and 15 m (50 ft) deep. It is believed that the lack of a properly constructed noncombustible shale barrier in the strip pit enabled the fire to spread to adjacent carbonaceous refuse material and then to nearby coal mine workings (PA DEP, 2017). As time went on, the fire grew and spread under the Borough and directly affected the residents despite various efforts to extinguish the fire by the state and federal governments (Fig.1). In 1984, a voluntary program was begun to move residents from their homes. Many accepted buyout offers for their properties and moved elsewhere and after leaving, their homes were demolished. In 1992, the state used eminent domain to take control of all the property within the Borough. In 2013, after years of litigation, the eight remaining residents were allowed to stay for as long as they lived. Today, only a few buildings remain within the Borough (Centralia, PA, 2014). This fire has been burning for more than 55 years."

Jan 5, 2018

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer gas studies, as well as for studies in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources have previously been demonstrated in mines, but this new work details the development and testing of multiple, distinct tracer compounds that can be used in passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed, which are PMCH, PECH and PMCP. The release rates of these tracers were examined over a 180 day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in understanding complicated ventilation circuits, flow through gob, and leakage. INTRODUCTION The use tracer gases for ventilation applications is an established practice, with various research projects being perform with Sulfur Hexafluoride (????6) in the past. Perfluorocarbon tracers (PFTs) however are relatively new compared to ????6, which is proven to be useful in ventilation and air modeling experiments along with other PFTs (Watson, Wilke, Dietz, Heiser, & Kalb, 2007). These liquid tracers are characterized by low background presence in air, inert behavior with other gases, high detectability with a gas chromatograph and low toxicity. A design was proposed called a permeation plug release vessel (PPRV), which initially introduced by Brookhaven National Laboratory to meet those requirements. The PPRV works by allowing the gaseous form of the tracer to diffuse through the permeable silicone stopper and evaporate into the open air on the other side. The PFTs inside the vessels are injected as a liquid but instantly begin to convert to their gaseous phases at room temperature due to high vapor pressures (Zhang, H., Cloud, A.,2006). Previous studies have detailed how release rates change based on plug thickness across various temperatures (Jong et al., 2015), but not on the release rate stability based on temperature across multiple tracers. For use in underground mines passive release sources need to be durable, be simple to manufacture, have customizable and reliable release rates as well as a long operating life. The PPRV vessel provides a steady release of tracer gas that is essential for long term passive release experiments, making it a viable vessel for the PFTs being tested. The PPRV design also allows for vessels to be bundled together to achieve release rates at detectable levels and allows for the capability to run ventilation surveys with multiple tracers simultaneously. The ability to conduct ventilation surveys with multiple tracers using the PPRV bundling design and detection of the PFTs makes testing the tracers and design together a promising potential for complex and long term mine ventilations studies."

Jan 1, 2017

By John J. Simmons

Federal and state regulations, in an effort to reduce acid rain, are becoming increasing more stringent regarding sulfur content of fossil fuels. Whereas coal from Illinois and Ohio contains between 1.5 and 37. sulfur, Wyoming has billions of tons of coal reserves containing less than O.5/% sulfur. However, much of Wyoming's coal is high in moisture, 25-30%, and low in energy, 8,200 to 8,900 BTU, vs. 10,500+ BTU for Illinois and Ohio Basin coals. Wyoming currently ships in excess of 130 million tons of coal to utilities as distant as Michigan, Wisconsin, Minnesota, Iowa, Nebraska, Louisiana, Oklahoma, and Texas. With freight charges ranging from $12.00-$20.00/ton, more than $1.5 billion a year is spent to transport water. A test shipment of more than 50,000 tons of Wyoming coal has recently been made from Mobil's Cabello Rojo Mine, south of Gillette, by Burlington Northern to the Robert's Bank British Columbia coal terminal for transloading and shipment to Taiwan Power Company. This coal assayed approximately 8,400 BTU/lb. and 277. moisture. Carbontec Energy Corporation feels the future availability of dried coal containing 11,000+ BTU could substantially enhance the potential export as well as the domestic market for Wyoming coal. Large and small utilities, along with industrial furnaces require tens of millions of tons of Wyoming, West Virginia, and other Eastern The federal government is encouraging the expenditure of hundreds of million of dollars by utilities to retrofit their boilers to allow them to burn higher sulfur coal. This program, if carried to completion, would cost many tens of billions of dollars, with the net result being high power costs sustained by the utilities. These costs will be passed on and paid for by the American consumer. A sensible alternative would be the burning of low sulfur coal by the utilities, without costly capital and operating expenditures. Carbontec Energy feels the successful operation of a Carbondry Coal Drying Plant in Wyoming will be the forerunner to other similar and larger operations in the State. CARBONTEC RESEARCH The activities of Carbontec's personnel to develop a viable process to dry sub-bituminous and lignite coal goes back some 14 years; in fact, for some of us it goes back to 1962 when we were involved in a program under which lignite coal from Truax Trayer's Velva mine was placed in low sulfur coal, which are burned alone or blended with high sulfur, Midwestern coal. Carbontec believes that a high BTU. reasonably priced, shippable coal fuel produced in Wyoming and delivered at costs competitive with Eastern low sulfur coal, could offer substantial benefits to Wyoming coal producers, utility customers, and to the State of Wyoming.

Jan 1, 1989

By A. Mull, J. Weyer, J. Brune

"The “Reiche Zeche” mine in Freiberg, Germany, a 600-year-old lead-zinc-silver mine with extensive open mine workings, experiences severe ventilation losses due to leakage. Much air leaks into abandoned workings, decreasing the airflow available to active working areas. Usually, this leakage occurs in remote areas that lack transportation infrastructure like roadways or rail, making it difficult to haul construction materials to the sites to erect passive ventilation controls such as stoppings, regulators and seals. Transportation distances make it impractical to hand carry traditional construction materials, such as bricks and concrete. Alternative materials, such as brattice, foaming polymers, concrete canvas, and some innovative ventilation control designs have been investigated for this purpose. The suitability of the materials investigated depends on many factors including the pressure it can withstand, the ease of transportation, and workability. Impacts of mine water must be considered, as the Reiche Zeche is below drainage and experiences significant inflow of water. Researchers must consider the effects water inundation as well as how the stopping construction material reacts to being exposed to acidic mine water. INTRODUCTION Problem Statement Mining in the area around Freiberg, Germany began in the 12th century. The mine is used for research, mining engineering education, tourism and air conditioning for a local hospital. The first records of mining in the Reiche Zeche are from around 1384. Due to the strength and competency of the host rock, many of the oldest workings still stand and remain open today, although they may not be accessible. Reiche Zeche also connects to several other, closed mines in the area that are largely unmapped. This allows air to leak into neighboring mines, reducing the air available to ventilate to the working areas of Reiche Zeche. In order to improve ventilation efficiency, it is necessary to control the ventilation and reduce leakage by constructing seals, stoppings and regulators. A challenge with building traditional seals and stoppings in the Reiche Zeche is that the old workings lack transportation pathways or rails. Also, the lack of compressed air, water or electricity makes it difficult to operate power tools and drills. This means that construction materials must be hand carried – some over distances of several kilometers. Figure 1 shows a typical drift in the Reiche Zeche. Researchers investigated using lighter, more easily transportable materials including concrete canvas, expanding polyurethane and polyurea foams, and brattice. The applicability and utility of these materials depends on a variety of factors including the ventilation air pressure, chemical resistance to acidic and mineral-laden mine waters, ease of transport, and ease of construction. Stoppings and seals must be substantially constructed so that they remain tight and do not require maintenance. It is also important to consider the toxicity of the construction materials in case of a mine fire."

Jan 1, 2016