Search Documents

By Paul S. Fisk, Arne Fareth, Julie Frietas, Francis Lo, Fidel L. Mallonga

INTRODUCTION This report describes the inspection of parts of the New Croton Aqueduct (NCA)undertaken for the New York City Department of Environmental Protection (NYCDEP)by Parsons Brinckerhoff Quade & Douglas, Inc., (PB) in association with Montgomery Watson Engineers of New York, P.C. (MWH). Support for the inspection was provided by AFC Enterprises, Inc., under Construction Contract CRO-333, “WM-11 New Croton Aqueduct Rehabilitation and Inspection Program.” The scope of the inspection work under CRO-333 included assessing the condition of the 10.3 km (6.4 mile) long, pressurized section of NCA and inspection of shafts, head houses and blow-off structures in both the pressurized and gravity sections. The CRO-333 inspection continued investigation work begun under ContractCRO-196, which ran from 1993 to 1997. The CRO-333 inspections were conducted from November 2004 to September 2005. Background The New Croton Aqueduct was put into service in 1891 to deliver water from the Croton River Watershed in Westchester County to consumers in New York City. Figure 1 shows the location plan of Croton Water Supply System. The design flow into Jerome Park Reservoir was 12.7 m3/s (290 mgd) and into the135th Street Gate House, further south, was 10.9 m3/s (250 mgd). The NCA has been operated as a gravity conduit from Croton Lake to Gate House No. 1, just north of Jerome Park Reservoir, since its original construction. The length from Gate House No. 1to 135th Street, which includes a major siphon under the Harlem River, has been operated under pressure. Croton Lake gate house, the north end of the alignment lies at Station 4+75; Shaft 33, the south end of the alignment lies at Station 1628+05. The diameter of the tunnel is 3.2 m (10.5 ft) in the siphon and 3.7 m (12.3 ft) in the Bronx and Manhattan sections. The pressurized sections, constructed in rock, consist of a brick lining surrounded by a mortared and grouted rubble backing. Figure 2depicts a typical tunnel cross section. The objective of the shaft and tunnel inspections was to locate and document defects, such as leaks, deterioration of lining material, cracks, spalls, delaminations,

Jan 1, 2007

By Edwin R. Phelps

Good morning ladies and gentlemen - today I am in an enviable position for two basic reasons - No. 1, since I am first on the program, the audience should start out awake because those that partied too much last night are still asleep, but in their room, not here. No. 2, since copper, iron, and mining technology are not competitive, the veracity of my statements will not be questioned. Most such meetings I attend are based on the subject of energy and the coal industry does have competition from oil, gas, hydro, and nuclear. However, to counteract this advantage I am the usual engineer with a limited vocabulary by schooling, and the remaining vocabulary almost completely eliminated due to the presence of ladies. In relation to the past of the coal industry, we have not only suffered the competition of other energy sources mentioned before, but in addition have in the last 25 to 30 years been required to meet the demands of a vastly changing market. To explain this statement, I am sure many of you can remember 30 to 40 years back when most homes were heated by coal furnaces or stoves and shudder to recall the shoveling of coal into the fire and the carrying out of ashes with the attendent manual labor dust. Now this space heating portion of our sales has almost become non-existant due to an almost universal switch from coal to natural gas, oil, and electric heating. Actual figures show a decrease from 119 million to less than 28 million tons per year in less than a twenty year span. Also, most of you can remember the coal burning steam locomotives and the tremendous volume of coal they consumed and then the very rapid change to the diesel-electric locomotives, incorporating improved large diesel engines driving D C generators and electric drive motors, which resulted in cheaper motive power. This change over was so complete that the annual tonnage of coal dropped from 125 million to less than 2 million tons in 15 years. 'Actually, now it requires some considerable interrogation and traveling to find a locomotive still operating on steam.

Jan 1, 1968

By C. E. Golson

Modern concrete technology emphasizes the basic qualities required of an acceptable aggregate: it must be clean, sound, homogeneous, and of a size gradation resulting in a concrete of the desired physical qualities at a minimum cost. In the case of coarse aggregates, crushing, scrubbing, and screening will usually provide the required material, although beneficiation is often necessary in order to eliminate unsound or deleterious fractions. Beneficiation is also applicable to fine aggregates,( but the processes most often employed are washing, classification, and dewatering.

Jan 1, 1959

By Jan Wolski

Increasing interest in the Bucket Wheel Excavator (BWE) technology calls for a universally understandable definition of suitable performance factors which would reflect the unique features of this technology. The importance of properly designed and calculated performance factors for the BWE systems cannot be overemphasised. They are used by all levels of management in any mining organization for a wide variety of purposes, in particular for budgeting, for selecting new equipment, for monitoring current equipment and for comparison with other operations.

Jan 1, 1984

By M. A. Cornachione

The west central upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur which can create emission problems when processed in a kiln. A low cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated.

Jan 1, 1992

The amount of hydrophobic materials constituting the mineral froth strongly influences the froth viscosity. Higher froth viscosity on the other hand can retard the drainage of physically carried over hydrophobic particles. In phosphate flotation tests a direct correlation was observed between froth viscosity and recovery and an inverse correlation between froth viscosity and grade. Phosphate flotation tests in the presence of a silica depressant indicated that higher froth viscosity is an effect rather than a cause of silica particles reporting in the froth.

Jan 1, 1992

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By John D. Smith

This paper describes how a knowledge of inherent rock characteristics can aid the mining engineer in his design of a mining method for a massive domelike structure. The paper shows how the pertinent rock characteristics were measured and analyzed and how the data obtained was used for design purposes. This analysis was conducted in 1964 in a producing salt dome, since that time, mine management has tried certain of the recommendations for mine design changes. The results of such changes are presented.

Jan 1, 1968

By Y. C. Kim

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the U.S. has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms.

Jan 1, 1988

By J. Bartrum

Kidston Gold Mines is a 14 000 tonnes per day rated operation located 280 kilometers west of Townsville in Queensland. The principle shareholder is Placer Development Limited. Kidston's orebody consists of 44.2 million tonnes graded at 1.79 g/t gold and 2.22 g/t silver. Production commenced in January, 1985, and despite a number of control, mechanical and electrical problems, each month has seen a steady improvement in plant performance to a current level of over ninety percent rated capacity.

Jan 1, 1985

By M. J. Fairweather, J. R. Egan, W. A. Meekel

Cominco Metals, in cooperation with two Canadian Universities and the Government of Canada, is developing applications for column flotation in the treatment of lead and zinc ores. Plant scale results at Polaris and pilot plant studies of Sullivan, Pine Point and Red Dog ores show column flotation to have significant advantages over conventional mechanical flotation for lead and zinc cleaning. Results from these ongoing studies are discussed in relation to ore texture, mineral recovery, impurity behaviour, scale-up and control.

Jan 1, 1988

By E. D. Attanasi

Geologic resource assessments describe the location, general characteristics, and estimated volumes of resources, whether in-situ or technically recoverable. Such compilations are only an initial step in economic resource evaluation. Forecasts that assume that resources that exist in nature can be commercially produced as needed ignore economic constraints. This paper identifies, by example, the salient features of a geologic assessment that will assure its usefulness for economic analysis. These features are demonstrated with examples of coal resource assessments and coal bed gas assessments.

Jan 1, 2001

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

By T. B. Jarboe, H. Wen

Introduction The 150 MW circulating fluidized bed (CFB) power plant described in this article is the product of recent Bechtel experience in the industrial power and steam market, where the economic feasibility of fluidized bed projects has been proven. The ability of CFB boilers to burn low grade fuels makes it possible to burn low ranking coals or coal wastes. These include anthracite culm, coal mine rejects, and coal wash-plant-waste slurries. This article also addresses the impact of fuel characteristics on plant design. This includes solids handling, steam generation, sulfur capture, and auxiliary load requirements. The uncertain economic environment in which utilities must now operate has shifted the industry's interest away from large, base-loaded generating units to small, more versatile installations. Utilities now consider purchasing new generating capacity in smaller increments and staging its deployment to correspond with demand increases. In this way, they lower their risk in the increasingly hazardous art of long-range load forecasting. This strategy has many advantages. Multiple, smaller units have inherently greater turndown capability and better availability than a single larger unit of the same size. In addition, the smaller units will each have better cycling capability. And, with CFB combustion, the smaller units will have greater fuel flexibility. General plant description The 150 MW powerplant described here is a grassroots CFB unit. Fluidized bed technology differs from conventional combustion techniques. With CFB, solid fuel, together with inert material such as sand, gypsum, limestone, or ash from the fuel, is kept suspended in the combustion chamber. This is done by using the action of the fluidizing air distributed below the bed. Fluidization promotes the turbulent mixing conditions required for good combustion. The turbulence causes the entire mass of solids to behave like a liquid. The result is improved mixing. This allows heat to be generated at a lower and more uniformly distributed temperature that is below the ash fusion temperature of most coals. The fluidizing mechanism offers several other advantages over conventional combustion. There is less volatilization of alkali compounds, which cause deposits on boiler tube surfaces. And there is less sensitivity to the quantity and nature of the ash in the fuel. The low combustion temperatures prevent vitrification of the ash particles and minimize problems associated with furnace slagging. The ability to select from many fuels is one of the major advantages of CFB combustor technology. Fuels that can be burned in CFB plants to produce steam and electricity include: low grade coals with high ash or sulfur, lignite, peat, wood and pulp products, biomass, refuse, anthracite culm, petroleum coke, and oil shales. The plant's turbine cycle uses superheated steam at 12.4 MPa (1800 psi) and 538°C (1000°F), with single reheat to 538°C (1000°F). Two high pressure and three low pressure, closed, feedwater heaters are furnished. So is a deaerator, which is an open, direct-contact heater. The CFB plant exceeds EPA's New Source Performance Standards (NSPS) for air emissions. The design limits sulfur dioxide (SO,) emissions to 0.25 kg/GJ (0.6 lb per million Btu). SO2 reduction occurs in the combustor by reac-

Jan 11, 1988

By B. Mather

I was very glad to see an article on alkali-silica reactivity of concrete aggregate in Mining Engineering. It is a topic that should be reexamined every 45 or 50 years. The last paper (that I am aware of) that examined this topic in Mining Engineering was Rexford (1950), who, at the time, was chief of the Petrography Section, South Pacific Division Laboratory, Corps of Engineers, Los Angeles, CA. The paper was presented at the AIME meeting in Los Angeles in October 1948. Professor Leming's discussion generally reflects the current state-of-the-art; but it provides no references for more detailed information. I wrote a paper titled "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," which was included in the Proceedings of the Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams (Mather, 1995). In it, I emphasized that it was the hydroxide ion (not the alkali ion) that caused the pore fluid in the concrete to dissolve reactive silica, producing alkali-silica gel capable of taking up water, thereby, causing swelling and rupturing of the concrete. Excessive expansion will not occur unless there is a sufficient amount of potentially expansive alkali-silica reaction product and water. However, this will not occur unless there is a sufficient quantity of reactive aggregate and unless there is a mechanism by which the pH of the pore fluid can get well above the normal value of about 12.6. In many cases it is sufficient that the cementitious medium not only contains portland cement but also contains ground granulated blast-furnace slag (GGBFS) or a pozzolan such as fly ash, silica fume, metakaolin, volcanic glass or calcined shale - any of which may have been included for economic reasons. If, however, the person selecting the ingredients for concrete knows that the aggregate is reactive (with no alternate nonreactive aggregate available) and if the person knows that the only available portland cement has a high alkali content (i.e., more than 0.6% Na2O.; Na2e = % Na20 + 0.658 x % K20), then it becomes irresponsible not to establish what reasonable precaution one should take. Professor Leming suggests using one of the following: 30% Class F fly ash, 50% GGBFS or 7% to 10% silica fume. My view is that one should prepare test specimens with the cement and aggregate to be used and then expose these both with and without at least two dosages of each of the various alternative materials (slag, pozzolan and lithium salts), so that the required dosage. to control the expansion is established. Then, economic considerations can dictate the final selection. I would point out to the author that GGBFS is not a pozzolan and is not an admixture, but, rather, it is a latent hydraulic cement. An admixture is, by definition, a material other than hydraulic cement. I commend him for suggesting that aggregate producers should become more active in knowing about the reactivity of their products and the precautions needed to permit those products to be safely used in concrete.

Jan 1, 1997

By Y. C. Kim

M.S. Azun The article unfortunately has some serious flaws negating the usefulness of the paper. The authors claim that kriging (linear kriging) is superior to other methods such as polygon. This is not the case. The deterministic methods (referring to polygon, ID, IDS, etc.) should not be compared with the statistical methods (linear kriging, disjunctive kriging, etc.) because they differ not only in their assumptions, but also their tools used in estimation. Thus, they give different results. By comparing the results of deterministic methods and linear kriging, the authors conclude that polygon, IDS, and linear kriging give an average thickness close to the value obtained from realizations. Besides, they argue that linear kriging gives less variance than the others (Fig. 2). The first conclusion is expected, due to the well-known central limit theorem. The second is the result of the statistical properties of different estimators. Thus, the comparison presented in the paper is rather meaningless because the authors have failed to follow basic statistical procedures. The numerical results of different approaches to an estimation problem cannot be generalized. In conclusion, the paper is not a meaningful contribution, and sadly, quite erroneous. Reply by E.Y. Baafi and Y.C. Kim The two key contentions made by M.S. Azun regarding the paper are: deterministic methods should not be compared with statistical methods and, hence, the results are erroneous; and the paper does not make a meaningful contribution. The first contention is an academic one. Most practitioners in ore reserve estimation could care less whether the tool they are using falls under a deterministic or a probabilistic method, so long as it gives the desired answers. It is probably for this reason that, whenever any new tool such as linear kriging is introduced to practioners in the mining industry, they would like to see a comparison test performed between the existing and the more familiar tools with a new and "strange" tool. Only when a new tool passes such a test, the generally conservative mining community would begin to utilize the new tool to its advantage. The second contention, is a subjective one. The final judgment should be left up to the readers within the mining community. If kriging is accepted more among practitioners, partly due to the paper, then the paper makes a practical contribution to the state-of-the art in ore reserve estimation. Finally, M.S. Azun entirely missed two main points in the paper. The first is that any comparative study of kriging vs. Polygonal or IDS should be performed for local estimation and not for global estimation. In the past, kriging was frequently compared with other existing tools in its performance on global estimation. Such results were nearly identical due to the central limit theorem effect, which further prevented the acceptance of kriging by practitioners. The second point is that a single case study using an existing property, as it was frequently performed in the past, is not sufficient because results depend not only on the tool itself, but also on the nature of the mineralization.

Jan 3, 1984

By Charles L. Kimbell

Introduction Despite the focus on the so-called "high-tech" and service components of the economy, the minerals industry in 1987 continued to provide the world the overwhelmingly dominant share of the total raw material supply for all manufacturing operations. And, in the form of fertilizers and other soil treatment materials, minerals also supplied indispensable raw materials to ensure continued high production of the agricultural and forestry sectors of the world's economy. Moreover, the role of minerals as a source of construction raw materials was essential to that sector. On the basis of preliminary and partial statistics on world output of crude mineral commodities, 1987 appears to have been a year of further recovery from the recessional years of 1981-1983. The value of world crude mineral industry production (all mineral commodities including fuels) apparently advanced about 5% to nearly $1.1 trillion in terms of constant 1983 dollars.' That is significantly above the recently revised 1986 level of nearly $1.05 trillion, but still considerably below the record-to-date high of $1.27 trillion set in 1980, as shown in Table 1. That growth in value took place despite relatively flat world oil prices - oil being the most important component of the aggregate, as it has been for decades. There is insufficient information available to assess the total value of processed mineral commodities (refined metals, refined oil, manufactured fertilizers and the like). But a figure of $2.6 trillion (constant 1983 dollars) would be a quite conservative estimate for those materials derived only from primary or newly mined materials. And an additional, as-yet-unestimated increment should be added for processed materials derived from secondary raw materials - scrap and other reclaimed substances. From a world trade viewpoint, minerals and mineral products dominate in terms of tonnage. For example, in 1985, on a weight basis, mineral commodities including fuels constituted more than 58% of all goods moving through the Suez Canal and 53% of all goods passing through the Panama Canal. These waterways cannot accommodate giant tankers and ore carriers. So an even larger share of total oceanic trade is composed of minerals and mineral products. Yet, in terms of value, the share of the total accounted for by these industrial essentials is much lower than that accounted for by other commodities, most notably sophisticated high-tech equipment and other goods with a relatively high per-pound value. Worldwide data on the value of mineral export trade for 1987 is so incomplete at this writing that it is impossible to assess that actual level. Indeed, the compilation of similar available data for 1986 covers only the exports of nations with developed market economies. In 1985, these countries accounted for only 67% of total world exports of all goods. They accounted for only 41% of world exports of major mineral commodities: crude nonmetals; metal ores, concentrates, and scrap; mineral fuels; nonferrous metals excluding gold; and iron and steel. For these developed-market-economy countries, the value of exports of these major mineral commodities declined by more than 10% between 1985 and 1986. Most of the shortfall came as a result of a 26% drop in the value of fuels exports. If these patterns of

Jan 7, 1988

By B. Hornsby

At the Mount Isa mine, Mount Isa, Qld., Australia, sublevel open-stope mining is used for copper ore while both sublevel open-stope and cut-and-fill methods are used for the silver-lead-zinc ores. Production in 1979¬80 was 4 730 000 t (5,200,000 st) copper ore and 2 590 000 t (2,850,000 st) of lead ore. The deepest mine level currently is 960 m below the surface. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The mine is located in the valley of the Leichhardt River in Lower Proterozoic sediments of the Mount Isa group. The regional strike of the sediments is north¬south and they have a persistent westerly dip of about 1.1 rad (65°). In the mine area, the Mount Isa group comprises a sequence of alternating bands of dolomitic shales and siltstones some 3.2 km (2 miles) in width. It is bounded on the east by greenstones and quartzose sediments of the Eastern Creek volcanics, and on the west by the Mount Isa fault, west of which occur schists and other metamorphic rocks. The ore bodies as currently known at Mount Isa are restricted to the Urquhart shale, a formation of thinly bedded pyritic, dolomitic, and volcanic shales some 1070 m (3500 ft) thick. Towards the top of the Mount Isa group sediments, copper and silver-lead-zinc ore bod¬ies occur as contiguous but discrete entities and are mined and treated separately (see Figs. I and 2). Argentiferous galena, sphalerite, pyrite, and minor associated sulfides occur in distinct concordant bands throughout the Urquhart shales. Wherever these bands are grouped together in sufficient density they constitute silver-lead-zinc ore bodies with widths varying up to 36.6 m (120 ft). Other mineralized bands are common in intervening beds. Individual ore bodies persist for many hundreds of meters concordant with the strike and dip of the enclosing shales. Intersections of these beds with fold axes provide local zones of enrichment but otherwise the mineral content of the ore bodies varies only slightly throughout the extent of the dip and strike. Chalcopyrite is the only important primary copper mineral. It occurs in association with pyrite and pyrrhotite as disseminated flocks and as vein fillings throughout irregularly shaped zones of folded, brecciated, and re¬crystallized Urquhart shale. These zones, which are lo¬cally termed "silica-dolomite" bodies, are broadly transgressive to the shale bedding and confine all significant copper mineralization to the virtual exclusion of silver¬lead-zinc mineralization. In some areas, the downward percolation of acidic water through faults and shears has caused extensive leaching of the coarse-grained carbon¬ates to depths in excess of 610 m (2000 ft), but most of the silica-dolomite remains unleached and the ground is competent. The majority of lead ore being mined is north of the main shaft pillar (R62, U62) area. The major lead¬producing areas for many years have been the Black Star ore bodies (2 and 5 ore bodies) and the Racecourse ore

Jan 1, 1982

By Robert E. Blackett

To help local governments plan for long-term supplies of sand and gravel for buildings and infrastructure, the Utah Geological Survey is assessing natural aggregate resources (mainly sand and gravel) in the St. George, Utah area. Whereas much of the aggregate in the study area is adequate for road-base construction, high-quality aggregate for Port- land cement concrete is limited due to geology, and also due to land administration and environmental issues. Virgin River alluvial gravels southwest of St. George are generally poor sources of aggregate because they contain clasts of soft sediments and soluble minerals derived from Mesozoic rocks. Elsewhere, widespread secondary calcium carbonate (caliche), as rinds and matrix in gravel, lower the quality of material. Young river-terrace deposits in Fort Pearce Wash, and along the Virgin River above St. George are the primary sources of sand and gravel for the area. Alluvial fans on the east side of the Beaver Dam Mountains, and on the west side of the Hurricane Cliffs are also sources of aggregate. Stream-channel deposits associated with "inverted valleys" north of the towns of St. George and Hurricane, Utah, and older pediment gravels on the west flank of the Beaver Dam Mountains may be future sources of high-quality aggregate. Accelerated urban development during the 1980s and early 1990s has caused St. George and other communities in Washington County to encroach upon sand and gravel pits originally located in rural, undeveloped areas. Urban residents often view nearby sand and gravel operations as undesirable neighbors and pressure elected officials to close the pits. Pit closures effectively eliminate the remaining reserve from the sand and gravel resource base of the area. More- over, resources may also be lost as new homes are built upon undeveloped sand and gravel deposits. The St. George area is particularly susceptible to loss of aggregate resources because high-quality natural aggregate for construction is already in short supply. Moreover, most of the land in the study area is administered by the U.S. Bureau of Land Management and subject to various land-use restrictions. Much of this public land cannot be developed for mineral materials, such as sand and gravel, because of federal regulations protecting rare plants and animals, archaeological sites, and important watershed areas. Of particular concern to resource development are areas designated as Areas of Critical Environmental Concern, Wilderness Areas, and Wilderness Study Areas. Protection for Endangered Species is a critical element in all planning efforts. Those species present in the St. George area or in areas near- by include: the desert tortoise, southwestern willow flycatcher, Virgin River chub, and dwarf bearclaw poppy. As the St. George area is depleted and/or deprived of sand and gravel resources through extraction and urbanization respectively, construction costs will rise unless conservation measures are instituted. To avoid the loss of aggregate resources, the UGS is pursuing a program of data gathering and field surveying of surficial deposits to determine tonnage and quality of the remaining sand and gravel resources. The resource information from this program will help land planners, developers, and government officials make informed decisions concerning urban development throughout the region.

Jan 1, 2001