Search Documents

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022

By John C. Nixon

In 1959, The Australasian Institute of Mining and Metallurgy (Aus. I.M.M.) was asked by the Federal Government of Australia and the State Government of South Australia to join in the formation and management of a new contract research organization which was subsequently named The Australian Mineral Development Laboratories (Arndel) ? This body was formerly the Research and Development Branch of the South Australian Department of Mines which had been set up to develop the Radium Hill uranium deposit. It had then gone into contract R&D and the State felt that it would be more appropriate for the Branch to become a separate national organization. The Aus. I.M.M. decided that a professional institute could not participate directly in Arndel and, as there was no other suitable industry group to do so, it formed the. Australian Mineral Industries Research Association Limited (AMIRA). AMIRA held its first Annual General Meeting in September 1959 when the first Council was elected and the Memorandum and Articles of Association were adopted. The initial task of AMIRA was to raise guarantees of work or cash from its members to underwrite Arndel for the first five years of operation. The Federal and State Governments also provided guarantees and Arndel commenced operations in January 1960.

Jan 1, 1977

By P. H. S. W. Kulatilake, T. Hudaverdi, C. Kuzu

Prediction of blast fragmentation plays a key role for overall productivity of mines. In this study, a new multivariate analysis procedure for prediction of blast fragmentation is presented. Several blasts performed in various mines and rock formations worldwide were brought together and evaluated. An extensive blast database was created. Blast design parameters, the modulus of elasticity and in-situ block size were considered to perform multivariate analysis. A complete multivariate analysis procedure was applied in three steps. First, a hierarchical cluster analysis was used to separate the blast data into different groups of similarity. Two different groups were formed based on the elasticity modulus values. In the second step, group memberships were checked by discriminant analysis. The dominant parameters of the occurrence of the groups were determined. Also, discriminant analysis was used to determine the group membership of the respective blasts. As the last step, the multivariate regression analysis was applied to develop prediction equations for estimation of the mean particle size of muckpiles. Two different prediction equations were developed based on the rock stiffness. Validation of the proposed equations on various mines was performed. Prediction capability of the proposed models was found to be strong. The models are not complex and are suitable for practical use at mines.

Jan 1, 2011

By K. J. Hartman

The term kaolin is derived from "kauling". a Chinese word meaning high ridge, which was the name of a hill in China where kaolin was first mined several hundred years ago.(1) Other common names used today for kaolin include "clay" and "China Clay". The former word technically has a broader meaning and could refer to various types of clays such as bentonite and ball clay as well as kaolin. China clay, as a descriptive term, apparently results from kaolin's origin as described above but could also be due to a significant historical use in ceramic applications. The terms "kaolin" and "clay" will be used interchangeably in this analysis because of the common practice of using these terms in the paper industry. Major reasons for kaolin's widespread industrial usages center on the mineral's (kaolinite) physical features of good color, low viscosity and inertness. Kaolin is described as a hydrous aluminum silicate with approximate composition Of 2H20.A1203.2Si02. As will be shown later, a new version of the product, calcined clay with modified hydration content, is gaining widespread usages. Components of any particular kaolin in addition to alumina and silica are viewed as impurities. The more valued deposits and, hence, higher priced kaolin products are those of highest purity.

Jan 1, 1986

By P. Jonsén

Understanding mill charge motion is important. In the charge, the centre of gravity is shifted from the rotational centre of the mill system, and its motion is induced by rotation of the mill, while at the same time the charge creates a torque into the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to the motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty to measure in a tumbling mill. Experimental measurements in a lab mill were done for diverse load cases: varying feed materials, mill fillings, mill speeds and pulp liquids. The mill is set up to directly measure the charge-induced torque. The accuracy is good with relative uncertainty smaller than ±2% for relevant load cases. A full three dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill start-up behavior for torque and mill power. This proves that the model is physically correct, and can be used for full-scale mills.

Feb 27, 2013

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By James Giulianelli

Personnel at the Jet Propulsion Laboratory (JPL) are studying the technology and applications of salt-gradient solar ponds (see below) for both electrical and thermal energy generation. The brine extraction and processing site operated by the Kerr-McGee Corporation at Searles Lake, California, offers ideal conditions for economic construction of solar ponds. Furthermore, since rising conventional energy costs adversely affect the economic recovery of brine by the present process, this site was selected for a study on the feasibility of integrating the solution mining of trona (Na2CO3?NaHCO3?2H20) in the lower salt with solar ponds for heating. The major emphasis of this study was to determine whether inexpensive thermal energy available at the brine extraction site would be useful in extracting increased mineral value from the resource. The present operation, which involves the simple extraction of the complex brine and its processing at the adjacent plant, is sometimes referred to as solution mining. Since the concept discussed in this paper involves injecting a heated sodium sulfate brine to dissolve carbonate underground, the proposed scheme is referred to as "enhanced" solution mining. The subject is discussed in greater detail in a recent JPL report. (1)

Jan 1, 1981

By W. Hoecker, S. Watson

The use of oxygen (Goldox™) in gold leaching has emerged as a significant modification in the past nine years. The Goldox™ process was ori gi na 11 y developed by Afrox Ltd ( part of the BOC Group) and is currently used in South Africa, Australia, Canada and the United States. Although a variety of benefits have been observed with oxygen, this paper out 1 i nes the main ones with reference to Australian plant data. The case studies were categorised into the ore type: Oxide, blends and primary ore.

Jan 1, 1992

By Jacob D. Baker

Sulphur dioxide is a versatile gas which has many uses throughout Pulp & Paper, Chemical, specialty Chemical, Mining and other industries. During recent years, S0 2 consumption and distribution patterns have resulted in renewed interests for liquid S0 2 and on site gaseous S02 manufacturing facilities. one relatively new use for S0 2 in the Mining Industry is its use for cyanide detoxification. Our purpose in this paper is to describe the process steps, economics and general technical features of so 2 gas generation using a Jet Type sulphur Burning System.

Jan 1, 1991

By Peter Krag, Rob Henson

It is well known that titanium and zirconium alloys offer superior corrosion resistance in the oxidizing sulfuric acid environments present in sulfide pressure leaching operations. The use of these materials is limited, however, due to their pyrophoricity; several accidents attributed to titanium equipment have been described in technical literature, and other, minor incidents·occur regularly1 • We describe an application of a commercial titanium alloy, Nb-55 Ti, with suitable mechanical properties, corrosion resistance similar to Grade 2 Ti, and featuring a significantly reduced field of ignition conditions

Jan 1, 1992

By Vernon F. Swanson

The expansion of a fluidized bed of carbon depends on fluid velocity, fluid temperature (viscosity) and particle size of the carbon. This paper presents a mathematical model which can be used to calculate the necessary fluid velocity. It will allow the design of sufficient freeboard in the column to accommodate expected operating conditions. Although this paper is keyed towards the use of activated carbon in precious metals adsorbtion from water solutions, the model is.valid with any fluid. Additionally, the method of calculating the required suspension velocity in CIL or CIP pulps is described.

Jan 1, 1992

By Michael Botz, Craig McKenzie

Recovery of cyanide from mill tailings can be conducted to lower the overall cost of precious metals extraction, while lowering cyanide concentrations in mill discharges and potentially eliminating the need to chemically destroy cyanide. Recent applications of cyanide recovery based on acidification­volatilization-reneutralization (A VR) technology have elimi­nated the need for cyanide destruction and substantially increased the profitability at several gold and silver operations. Recent developments in the technology permits processing of scale-prone and high percent solids pulps while generally affecting cyanide recoveries in excess of 70% to 90%.

Jan 1, 1997

By M. Cimini

The main objective of this paper is to propose a new sustainability parameter, called Visibility Indicator (VI), to describe the influence of mining operations on the visibility of the open works in the site from the surrounding land. A further goal is to point out a procedure for Visual Impact Analysis and Assessment (VIAA) of mining and quarrying operations in the phases of elaborating and evaluating of the project and depleting the resources. The Visibility Indicator has been computed taking into consideration the evolution of the area involved in the exploitation activity.

Jan 1, 2003

By C. J. Barbee, P. J. Bethell, C. J. Wood

Heavy medium cyclones (HMCs) are commonly used to clean run-of-mine coal in the 50 x 0.5 mm size range. Unfortunately, field studies suggest that industrial HMC circuits are often poorly designed or improperly operated, resulting in significant losses of recoverable clean coal. To assist plant engineers in overcoming these problems, a spreadsheet-based simulation package has been developed to predict HMC performance based on mathematical expressions originally developed by Wood (1990). A case study is provided to illustrate the predictive capabilities of this simulation package for an industrial HMC.

Jan 1, 2004

By John R. Turney

MARY KORPI: Harry Hinds will be filling in for John Turney today. Harry is an exception to the industry these days, in more ways than one. He has worked for the same mining company for 33 years. That is something very few of us can claim. He is currently metallurgical superintendent for Homestake Mining Company in Lead, South Dakota. Harry is also the envy of many of us as he will be retiring this year and working on lowering that handicap! Harry will be discussing the "Role of Consultants."

Jan 1, 1998

By Tim Wolf

The paper "Weld Notch Affects on Pulley and Belt Conveyor Reliability" has done an excellent job of describing theoretical fatigue and fracture mechanics methods used in modern weld design. From this foundation, we intend to further detail areas previously discussed and present new research in the application of these principles to pulley weldment life prediction. Affects of changes in alternating stress range, mean stress, and residual stress have been investigated using controlled laboratory fatigue tests on a pulley weldment. Comparisons between these results, weld codes, and theoretical fatigue predictions will be made and discussed.

Jan 1, 1998