Search Documents

By Bill Dershowitz

Consider a deep gold orebody with grade of 4 g/t (0.11 oz/st). At the time of this writing, with gold prices at historic highs, it could be a good, but not great, prospect. But if it is a vein deposit, and those veins are 200 g/t (5.8 oz/st), it would be significantly more attractive if there was a way to produce directly from those veins, leaving the rest of the rock in place. [Figure 1 The red around each of the four injector wells shows areas of high pressure, where the lixiviant fluid is pumped into the rock mass, with orange and yellow indicating dissipated pressure. The black lines indicate some of the fracture pathways through which the lixiviant, with absorbed metal, flows toward the central recovery well where low pressure is indicated in blue. Lixiviant is pumped out through the recovery well. Image courtesy of Golder Associates.] There is a way to do this, in situ leach (ISL) or solution mining. It has been a viable commercial technology for more than five decades.

Jan 1, 2011

By I. Sanchez

The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites. The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites.

Feb 23, 2014

By David Cronan

"Most of the recent renewed interest in manganese nodule mining has been focused in the Clarion-Clipperton Zone (CCZ) in the NE tropical Pacific where nodules are rich in Mn, Ni and Cu. However, equally interesting, but compositionally different, nodules occur in the tropical central South Pacific (CSP). The CC Zone deposits lie in the International Seabed Area whereas those in the South Pacific lie mainly in the Exclusive Economic Zones of Island States, principally the Cook Islands and Kiribati. The CSP nodules should not be regarded as an alternative resource to CCZ nodules, as they are enriched in different elements. Rather, the CCZ nodules should be thought of as a source of one group of metals (Mn, Ni and Cu) and the CSP nodules the source of another group (see below), mutually complementing each other and to be mined in parallel for their different metals.Manganese nodule mining in the South Pacific has been mooted since the 1970s. However, new data on manganese nodule composition and abundance there have recently appeared. Also, a recently developed interest in 'rare', 'green' and 'technology' elements has necessitated a re-examination of old South Pacific nodule data for information on these elements (previously thought to be economically unimportant), and the re-analysis of the deposits to obtain new data on them. Additionally, current and possibly future applications to the UN to extend island 'continental shelf' areas necessitates an appraisal of the manganese nodules in these areas. These developments have prompted recent work that has helped to refine our understanding of the distribution and abundance of metals of traditional interest in South Pacific nodules, namely Mn, Co, Ni and Cu, but has also drawn attention to other elements of possible economic interest including titanium (Ti), vanadium (V) and the rare earth elements (REE)."

Sep 1, 2014

By Jacob Carr, Rebecca Knuth, Emily J. Haas, Marvin Cheng, Bob Bissonette

Many industries, including mining, are experiencing an increase in the use of robotic and other artificial intelligence (AI) systems to improve efficiency, productivity and precision. For example, a 2023 survey showed that mining industry executives wanted to integrate more autonomous equipment to improve productivity and alleviate workforce shortages (Haas, 2024). This feedback was coupled with an increased appetite to advance the types and uses of automation and AI in the workplace. However, there is also an increasing concern about the ways that robotic applications may unintentionally affect worker safety. Humanmachine interaction poses potential risks, especially when industrial robots operate near workers in specific environments (such as drilling, handling and transporting materials, equipment inspection and lifting heavy loads). Research has explored the unintended consequences of introducing new technologies or processes in the workplace to include incidents such as being struck by equipment and challenges around data privacy (Lööw et al., 2019; Khurram et al., 2025; Haas and DuCarme, 2015; Almeaibed et al., 2021; Zio and Miqueles, 2024). More recently, the use of digital twin technologies and simulations (hereafter referred to as digital twin systems) has been boasted as a tool that can help prevent unintended consequences around worker safety by identifying and mitigating risks before a worker completes a task in tandem with a robot or other new technology. Digital twin systems produce a virtual replica of a physical environment or process (Almeaibed et al., 2021; Zio and Miqueles, 2024; Saes, 2024). To this end, this article explores the potential role of digital twin systems in enhancing safety within mining and other similar environments. It will primarily focus on environments where robots and human workers may interact, although digital twin systems can be useful with other technology applications. First, we define digital twins and digital simulation as components of a system. Then, we highlight possible applications of digital twin systems in mining to replicate real-world processes, followed by potential benefits of their use and where more research may be needed.

Oct 1, 2025

By M. Batzle

The upper Arkansas basin has some of the greatest potential for geothermal development in Colorado. Over several summers, students conducted an investigation using seismic, gravity, and magnetics in order to help identify the large structures and basin fill associated with the Rio Grande Rift. Adjacent to Mount Princeton Hot Springs, near surface geophysics was conducted to help understand the faulting and fractures that act as a conduit for hydrothermal flow. The methods used included high frequency 3D seismic, magnetics, gravity, D.C. resistivity, and self potential. Throughout the Mount Princeton area, passive seismic, vertical seismic profiling, and well logging were also used to better understand the geology and activity of the region. The results indicate for the area northwest of the hot springs, a 40 to 50 m thick unconsolidated layer overlying the fractured granitic basement. The DC profile shows a deep geothermal anomaly of low resistivity which correlates with a positive SP anomaly in the same region. In the Chalk Creek valley, a shear zone extends from the north east to the south west, just south of the Chalk Cliffs. There appears to be an upward migration of the water through this shear zone which then flows along the porous sediments towards the south in this area. The deep seismic data collected in the center of the basin suggests that the depth to the basement is approximately 2000m. Also identified on the deep seismic are two major faults on the west end and two minors at the east end of the cross-section. An alteration zone is identified between the faults and a possible Precambrian northeast trending shear zone. The potential for developing an Enhanced Geothermal System (EGS) near the center of the valley is high. Our geophysical results indicate a deep basin fill near the center of the basin providing high temperatures. The range front (Sawatch) fault is observed to penetrate under the center of the basin and is an attractive target for natural fractures.

Jan 1, 2011

By Josef Martinsen

This paper describes two-lane dual motorway tunnels under construction in Bergen. The tunnels are part of a by-pass motorway system throuth the most congested area of the city of Bergen. The tunnels are unique due to their length, heavy traffic, longitudinal ventilation system and the use of a tunnel boring machine, or "TBM", to excavate through hard rock. The tunnels are being built by The Norwegian Public Road Administration and the TBM was delivered by the Robbins Company. The diameter of the TBM is 7.8 m and the tunnel profile is cut by conventional drill and blasting methods in the tunnel's lower half to attain a two lane motorway tunnel. This paper also describes proposed fjord crossings along the Norwegian west coast where the TBM may be used due to its great advantages in comparison to conventional drill and blasting methods.

Jan 1, 1987

By S. S. Mauney

Natural and synthetic colors are used in almost every facet of our daily lives as a means of communication and expression. Natural ochres, umbers, hematites, and magnetites were once used in their crude or semi-processed state for their pigment value in construction products and low-end coatings applications, while yielding, in recent years, to synthetically produced iron oxides for more sophisticated products. Today, through innovative mining, processing, and marketing techniques, natural iron oxide pigments are once again gaining strong inroads into products and markets requiring precise chemical and physical characteristics. With our focus on environmental consciousness and resource conservation, value added natural iron oxides provide an economical and responsible alternative to our color needs.

Jan 1, 1993

By Wern-ping Chen, Joseph Pratt, Thomas G. Brueckner, Tracy K. Lundin

To address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area, the Narragansett Bay Commission completed a comprehensive Combined Sewer Overflow (CSO) Facilities Plan in 1993 which included a series of deep rock tunnels. Since completion of preliminary design of the program in 1994, the program has been reconfigured in response to the Environmental Protection Agency’s (EPA’s) new CSO policy. The currently proposed system consists of a deep rock tunnel with two tunnel stubs which will provide230,000 cu m (62 million gallons) of storage at depths of up to 90 m (300 ft). This paper discusses the revised 5 km (3 mile) long deep tunnel system.

Jan 1, 1999

By Jon Hurt

INTRODUCTION The entire scope of new facilities for Lake Mead Intake No. 3 includes a sub-merged intake structure, a deep tunnel beneath Lake Mead, a tunnel access shaft, Intake Pumping Station No. 3, and connections to an existing intake and water treat-ment facility, as shown in Figure 1. In March 2008 Vegas Tunnel Constructors (VTC), a joint venture of Impregilo SpA and SA Healy were awarded a $447m Design-Build contract by SNWA for a section of this work (Contract 070F 01 C1), including the 185 m deep tunnel access shaft, the 4.7 km long, 6.1 m diameter tunnel and the submerged intake. Arup, supported by Brierley Associates, is the Design Engineer for VTC. The scope of the work is shown in Figure 2. This paper will describe the design and construction on this contract, with a focus on the access shaft which is the most complete section of the work. The shaft is being sunk using drill-and-blast methods with the finallining placed as excavation proceeds. The shaft passes through a major fault zone, and extensive pre-excavation grouting for water control is required for much of the depth of the shaft.

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

By Claude Deveau, Stephen R. Young

Introduction Tanco History Tanco is sometimes known as the Bernic Lake Mine. It is located about 180 km east-northeast of Winnipeg close to the Manitoba-Ontario boundary. Tanco operates an underground mine employing ramp access, room and pillar mining and shaft hoisting for the production of tantalum, lithium and cesium minerals. Tantalum recovery employs conventional gravity and centrifugal concentration methods along with a flotation process which recovers ultra-fine tantalum. All tantalum concentrates are shipped to Cabot Supermetals, Boyertown, Pa., for the production of tantalum chemicals and metals. Tanco also produces lithium products from spodumene ore. The lithium concentrates from Tanco are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock to the on-site chemical plant dedicated to the production of cesium formate, a high density drilling fluid. Tantalum milling operations commenced in 1969. In the early years of the operation, feed grades were three to four times as high as they are today. Coarse-grained tantalum mineralization with complete tantalum liberation at sizes of 300 µm allowed for easy recovery with conventional equipment such as spirals and shaking tables. Over the years, the process and feed material to the plant have drastically changed. Due to drastically reduced liberation sizes, efforts have been made to try to recover as much of the liberated particles as possible in order to maintain acceptable recoveries.

Jan 1, 2005

By SANJIT KUMAR PAL, Sarvesh Kumar, Arindam Guha

The integrated geophysical study around pipe 1 and pipe 2 in Wjarakarur Kimberlite Field (WKF) assisted in comprehending the response of pipes. In the present study, we have attempted a combined analysis of very low-frequency electromagnetic (VLF-EM), electrical resistivity tomography (ERT), and magnetic methods to analyze the response from pipe 1 and pipe 2. A comparative analysis along all the profiles revealed the extension, depth, and geometry of the pipes. The results of VLF data and ERT data have been compared for two profiles of pipe 1 and pipe 2. Fraser-filtered grid map generated from all profiles of pipe 1 proficiently demarcated the trend of kimberlite pipe extension with high Fraser filter value associated with kimberlite. The ground-based magnetic data around pipe 1, pipe 2, and pipe 6 have been processed to analyze the magnetic behavior and subsurface structure based on the susceptibility contrasts. Analytical signal (AS) map revealed the extension of pipes, which was validated with the Fraser-filtered grid map. Analytical signal anomaly pattern reveals that pipe 1, pipe 2, and pipe 6 are trending in SW-NE, NE-SW, and NE-SW, respectively. Based on this study, the results indicate the conducting nature of pipe 1, whereas pipe 2 is resistive in nature. Further, the Euler deconvolution technique has been applied to calculate the possible depth of pipes from magnetic data. The comparisons of calculated depth ranges obtained from all geophysical techniques correlate well and validate the result (Table 1). The geological borehole data at pipe 1 and pipe 2 reported by the Geological Survey of India are well corroborated with our combined geophysical study.

Jan 17, 2024

By M. A. Georgiana

The Emerald Mine No. 1, located in southwestern Pennsylvania is presently owned and operated by Cyprus Minerals of Englewood, Colorado. High volatile bituminous coal is produced from the Pittsburgh No. 8 seam by both longwall and continuous mining methods. The coal is then mechanically cleaned on site utilizing a combination of heavy media separation and froth flotation methods prior to shipment to both the metallurgical and steam coal markets. The Emerald Mine is presently producing 2.8 million raw tons per year, while liberating approximately 6.5 million ft per day of methane. In light of the methane liberation rate, ventilation requirements have been significant and have always received utmost priority and consideration. Figure 1 shows the locations of the current and proposed shafts. Emerald utilizes two Joy (Model M120-58-880) axial vane fans on shafts No. 1, No. 2R, No. 3R. (one operational, one stand-by) The use of computer simulation of various ventilation networks was initially employed during the design stages (1975-1977) and has been utilized through the present. Obviously, the initial planning, under the ownership of Lykes Resources, was strictly theoretical. All the quantities were proposed and the resistances were based on prior simulations of other mines and mathematical formulas. However, once the mine was moderately developed, actual values were recorded and utilized. This procedure consists of: a) layout pressure and quantity points b) measure all air quantities where an air course splits

Jan 1, 1986

By James J. Gusek

Passive-treatment systems that mitigate acid-rock drainage (ARD) from coal mines have operating since the mid-1980s. Large systems at metal mines are being contemplated. A 95L/sec (1500-gpm) capacity system is planned this year at an underground lead mine in Missouri. Mine, process and environmental managers need to understand how and why passive-treatment systems work. They must understand what operational limitations to expect, as well as the economics of construction and operation compared to the alternatives, like lime precipitation. Wetlands have been recognized as nature's method of improving water quality. Contaminant reductions can occur through the precipitation of metal hydroxides, sulfides and carbonates and pH adjustments. Local conditions, oxidation state and water and soil chemistries dictate whether these natural reactions will occur under oxidizing (aerobic) or reducing (anaerobic) conditions.

Jan 1, 1995

By James Thompson

Mine planning at Consolidation Coal Company's (Consol) Glenharold Mine in North Dakota is being constrained by environ¬mental concerns that did not exist when the mine opened in 1965. One such concern which developed in the mid-1970's is the impact of mining on woodlands that are considered impor¬tant wildlife habitat. To better coordinate mine planning with permitting, a cooperative task force was created to evaluate woodlands for their wild¬life habitat potential. The task force included representatives from Consol and state and federal agencies. This cooperative process is seen as a method of communication between industry and government and as a way of developing decision-making tools for mine planners and regulatory agencies.

Jan 1, 1981

By Thomas Schwind, Pamela S. Moran

For short tunnels, a reinforced cast-in-place lining is not economical and shotcreteis a logical substitution. In the past, reinforced shotcrete linings have been constructed with lattice girders and welded wire fabric. For the Russia Wharf Tunnel in Boston, MA, the Contractor, with the help of the Dr. G. Sauer Corporation offered the MBTA a VECP to substitute the reinforced cast-in-place concrete lining with a steel fiber reinforced shotcrete lining. The challenge was to adequately model the ductility of the steel fiber reinforced shotcrete and to test the shotcrete prior to and during construction to assure quality control. To our knowledge, this type of numerical simulation has not been used on any other tunnels in the US.

Jan 1, 2005

By R. Keith Evans

Potential large scale uses in secondary battery systems and fusion reactors together with a steady increase in demand for conventional applications, particularly in aluminum smelting, has resulted in an increasing interest in lithium and its compounds. Current world requirements are met from both granitic pegmatites and non-pegmatitic sources and although the emphasis in this short paper is on the pegmatitic minerals, and, in particular, on their "direct usage" applications, a short summary of other sources and requirements for chemical production is included for the sake of completeness.

Jan 1, 1977

By G. W. Luxbacher

With the advent of acid rain legislation included within the Clean Air Act Amendments of 1990, a great deal of uncertainty with regard to price, source and production quantities has been cast into the coal market. Powder River Basin and other western coals continue a rapidly accelerating migration eastward, South American coals move into the northern markets, states propose legislation to assist utilities in complying with the new regulations in hopes of maintaining their own coal industries, while some utilities question the long term availability of eastern compliance coal. Any major coal producer must make decisions now to assure their continuing presence in the market place; several companies have adopted a strategy to acquire eastern compliance reserves while others have invested in technology to compete as a low cost producer. This paper discusses some of these options in light of the uncertainties of the market place, from an eastern coal producer?s viewpoint.

Jan 1, 1992

By G. Caron, M. Boisclair

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce the energy consumption, thus contributing to the reduction of Green House Gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. A soft-sensor prototype, based on primary crusher data (i.e. energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index, and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e. use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2007

By D. C. Fuller

CoaLiquid, Inc. (CLI) has been in the coal- oil-mixture (COM) business for over five (5) years. The initial pilot processing facility was replaced by a 2000 barrel per day commercial production facility in August of 1979. For over two (2) years CLI has been expanding its efforts and conducting large scale production and combustion demonstrations successfully in many locations across the United States. To facilitate the marketing effort, CLI has recently constructed a special trailer containing all equipment needed for a temporary COM retrofit. CoaLiquid has conducted commercial scale combustion demonstrations in the following types of combustion units: kilns, calciners, industrial boilers, blast furnaces and driers.

Jan 1, 1982