Search Documents

By Jr. Pitts

Elevation of surface charge density on colloidal particles in the presence of a high potential electrostatic field is demonstrated as a viable technique for preventing the accumulation of solids in solvent extraction circuits. The effect of the technique is manifest by relative turbidity measurements between pregnant leach solution and raffinate, by changes in the character of the sludge accumulations, by alteration of the zeta potential of particulates, and by a general reduction in the mass of solids.

Jan 1, 1992

By John F. Oyler

The performance of high alumina refractory subjected to high compressive loads and high temperatures is an area in which operating experience is quite limited. This paper documents the results of five months of operation of a combustion chamber lined with 83 pct alumina brick subjected to compressive stresses as high as 45psi and hot face temperatures of about 2750°F. It also describes a method for predicting long term subsidence results based on the limited information available in standard hot load limit tests. Descriptions of the chamber itself and the pilot plant upon which its design was based are included.

Jan 1, 1978

By J. A. Haggman

In a country richly endowed in mineral wealth, Climax Arimco Mining Corporation's (CAMC) Dinkidi porphyry Au?Cu deposit in Nueva Vizcaya province, Philippines, represents the most significant mineral discovery in the country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon a region previously unassociated with porphyry-style mineralization. Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.41 % copper. Regional exploration throughout CAMC's 37,000 hectare FTAA has identified a further sixteen potential porphyry-related deposits. A new mining law was passed in March 1995 but prior to that CAMC had the first Financial and Technical Assistance Agreement (FTAA) granted by the Philippine government allowing 100% foreign ownership of mining projects.

Jan 1, 1997

By Guangyao Si, Ismet Canbulat, Xun Luo, Yi Duan

Routine analyses of seismicity and event locations are essential for coal burst risk management, especially in the presence of unfavorable and complex geology. In an Australian longwall coal mine, a small-scale seismic monitoring network was installed to monitor a section of a major dyke intersected by the roadway, which was classified as a coal burst prone zone. The Deep Convolutional Neural Network (DCNN) technique was adopted for automatically discriminating seismic events to assess seismicity in this zone. The discriminated seismic events were located with the Shortest Path Method based on the Boundary Discretization Scheme (BDS-SPM) for temporal-spatial seismic event distribution analysis. The results demonstrate that the seismic events are discriminated with an average accuracy of 94%. Moreover, the seismic events are more accurately located using the BDS-SPM with a 3D heterogeneous velocity model compared with results obtained with a homogeneous velocity model. The temporal and spatial variances in seismic activities identify that the rock fractures in the dyke zone are closely related to the longwall mining process and a local dyke has a controlling influence on the stress concentration in its vicinity.

Apr 26, 2022

By M. C. Mound

A recent development using XRD techniques, a unique fixed detector, specifically permitting full mineralogical information simultaneously for the first time, specially designed sample preparation and presentation system and Rietveld codes provide a continuous real- time analysis on the true contained mineral polymorphic composition of powder streams such as ore materials, cement, ground clinker or any other mineral stream conducive to XRD analysis. There are several COSMA systems currently operating in the US, Canada, Italy and Australia, proving service and reliability of this concept. The mineralogical information generated continuously in real time is used for automated efficiency, product quality and reduces costs. Quantitative Phase Analysis information is transmitted to the plant DCS via Modbus over RS422 or ethernet. Some limited information is stored in the on-board computers for optional future use at the operator?s option.

Jan 1, 2010

By H. N. Frock

The use of low-angle forward light scattering for measurement of particle size distribution has been described previously.1 Laboratory instrumentation using this technology is used routinely in operating plants for quality control and production control.2,3 Extension of the technique to on-line process monitoring and control has also been undertaken in several important areas. This paper will discuss the application of MICROTRAC R systems to the monitoring of particle size in wet slurry processes and dry powder grinding circuits. Examples of existing installations will be given with emphasis on performance and on-line reliability.

Jan 1, 1979

By John D. Elmes

The purpose of this paper is to describe the geology and the modelling work carried out to date. The Lisheen Zinc-Lead deposit was discovered in April, 1990. The deposit comprises two stratiform sulphide orebodies, hosted within the Lower Carboniferous Waulsortian limestone formation. The fully diluted geological resource is 22.5 Mt @ 13.02% Zn and 2.19% Pb, based on a total of 548 diamond drill-boles and 10,998 sampled core intersections. Due to the absence of a geological marker it was necessary to apply economic criteria to define and model the resource envelope. In common with other drill-hole geological databases, the establishment of a workable geological model presents unique challenges.

Jan 1, 1998

By E. Watkins, R. Kimutis, H. Dougherty

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry and can assist with a well breach scenario. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Mar 2, 2022

By Wade Edward Speer

The Hiddenite District of Alexander County, NC has produced some of the world?s finest large emeralds since the first one was discovered 134 years ago. In fact, North America?s largest emeralds come from the district, making this one of the continent?s most unique gem deposits. In addition to emeralds, the Hiddenite District is also famous as the discovery site for the rare spodumene mineral hiddenite, first identified in 1881. Nowhere else in the world do these two minerals naturally occur together. The emeralds are a unique color variety of beryl (Al2Be3Si6O18) with trace amounts of Cr+3 and V+3 substituting for Al+3. The hiddenite (LiAlSi2O6) crystals also exhibit emerald green color due to traces of chromium. Consisting of three large deposits and numerous prospects, the district encompasses an area of 10 km2 (4 sq miles) centered on the small town of Hiddenite. Operations at the Adams, Ellis and North American Emerald Mines properties have been productive at irregular intervals since the 1880s. Currently, only the North American Emerald Mines property is being mined on a regular basis. Recent activity there has exposed a 3-hm2 (7.4-acre) pit with depths of 25 m (82 ft) that provides the best exposures of unweathered bedrock seen in the district in more than 120 years. Although no official records exist, public and private data indicate that the production of the entire Hiddenite District from 1880 to 2007 is about 70,000 carats of emerald and 20,000 carats of hiddenite. The bulk of the emeralds came from the North American Emerald Mine property (NAEM, formerly known as the Rist Mine) where sustained mining replaced the previous sporadic prospecting in 2000.

Jan 1, 2009

By H. E. Hirsch

Propelled by the invention of the transistor at Bell Laboratories, germanium's unique properties have advanced our electronic world by many years. Germanium has found major uses in infrared optics, fiber optics and a revised vigor as a catalyst for PET plastic production. Other advanced applications are in various stages of development. The solid state electronics industry has been the driving force behind the accelerating demand for gallium since the late sixties. Past developments of substrates for light emitting diodes, lasers and magnetic bubble memories are paling in view of the current excitement over the use of semi-insulating gallium arsenide for high performance integrated circuits. This application requires gallium metal and gallium compounds of extraordinary purity.

Jan 1, 1986

By R. C. Bratton, R. Q. Honaker

Hindered-bed separators are recognized as low-cost, high-capacity devices for both classification and density separation; however, since their inception, there have been few significant advances in the fundamental technology. Recently, Eriez has shown through modeling and pilot-scale testing that the innovative approach to feed presentation offered in the CrossFlow teeter-bed separator provides improved metallurgy when compared to traditional hindered-bed classifiers or single-stage coal spirals. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Most recently, a side-by-side industrial scale evaluation has verified that this technology improves overall efficiency and simultaneously reduces the separation cut-point. With regards to coal processing, data from full-scale units indicate that the CrossFlow offers good separation efficiency, high unit capacity, and metallurgical results consistent with laboratory- and pilot-scale separators.

Jan 1, 2006

By Henry P. Ehrlinger

These are exciting times for those of us involved in the discovery, development, beneficiation, sales and end uses of industrial minerals. The known sources of traditional raw materials are rapidly being consumed or covered up with highways and urban developments. We would never knowingly cover up a source of gold, silver, diamonds, or even base metals with a shopping center, but it has been difficult to justify not locating construction atop a limestone, granite, or sand dune deposit. During the last ten or so years most of the users of significant amounts of industrial minerals have established task forces made up of geologists, mining engineers, beneficiation experts, ceramic and refractory scientists, and senior members of their purchasing departments whose duty it is to determine where the raw materials for their particular finished products will come from now and farther down the road, like 20 years from now. Likewise, these same ceramic and refractory scientists are developing new materials which require a never ending change into different raw materials and the traditional materials must be refined by selective mining, exotic beneficiation practices and expensive but necessary post-beneficiation treatments to produce minerals for commercial use that were either theoretical minerals or at best showcase specimens when most of us here today were in school studiously acquiring a vocabulary which included Calcite, Magnesite, Dolomite , Feldspar, (Labradorite had the play of colors the prof could see but which I rarely focused on) Wollastonite, Celestite, Chromite, Olivine, Barite and Lepidolite to name a few.

Jan 1, 1976

By C. Clark, J. Johnson, M. Stepan

"Shotcrete and mesh are often installed to control ground deformation, falls and ejection between bolts. The combination of mesh and shotcrete forms a panel or plate that is typically bent by ground extruding between restraining rockbolts. The ground pressure applied (that is, the resistance of these panels to bending) over large ground deformations is important for maintaining ground support safety. This paper describes a new test device that measures this resistance and its evolution over large deformations. Mixes of shotcrete, mesh and other components that can maintain significant support pressure are desired, a characteristic described as the “toughness” of support. Results show toughness depends largely on how shotcrete is integrated with other components. Shotcrete strength is less important. INTRODUCTION Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often called upon to do this (Figure 1). Applications are especially common in mines with squeezing ground or seismic loading. The support pressure maintained during ground deformation is key to the performance of these systems, and to protecting miner safety. However, the toughness of a design is difficult to estimate. Researchers at the Office of Mine Safety and Health Research (OMSHR) responded to this deficiency or “gap” by designing a full scale test device, described in this paper, and beginning a testing program. Some initial results from this program are reported to demonstrate test capabilities.BACKGROUND - TOUGHNESS Mining in ground that fails from the combination of in situ and mining induced stress is commonplace. Ground support elements are installed to reinforce such ground and preserve mine safety. Typically, the strength of support is considered key, and is used to prevent or halt yielding. However, ground movements driven by creep of weak ground or seismic loading may be impossible to halt altogether. In these cases, it is essential that support is able to yield with the ground in a safe manner while maintaining confining pressure that mobilizes the strength of rock in the immediate perimeter of the opening. In addition, it’s usually desirable to contain ground between rockbolts to protect miners from loose rock that might fall or be ejected. Shotcrete and screen are often employed, sometimes together and in combination with other support elements, to accomplish this function. A key characteristic of such a system is its ability to maintain support pressure through large ground deformations, a characteristic often called “toughness” – especially in support systems incorporating shotcrete. Toughness can be quantified as the work done during deformation (e.g. force x displacement)."

Jan 1, 2015

By Shu Fan Chau, Innes Duncan, Harry Asche, Bill Newns

The North Auckland Line (NAL) in Northland, New Zealand, is being upgraded to pass Hi-Cube containers. The line includes many tunnels and bridges which need to be refurbished to improve structural clearances and line capacity. Tunnel 2 along the line, the Makarau Tunnel, has posed special challenges. Opened in 1898, the tunnel suffered multiple collapses during construction and has shown significant distortion during operation. The tunnel has been repaired many times since opening. Successfully enlarging this delicate and distressed structure has involved historical research, advanced analysis and design, and careful construction. The results provide lessons for dealing with brick lined tunnels and poor ground conditions

Jun 13, 2021

By Robert Kimutis, Heather Dougherty, Eric Watkins

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry as a predictive tool for planning and monitoring and can assist with a well breach scenario over a large mining area. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Oct 12, 2023

By W. Fletcher

Startup of a new plant is a very interesting time. It generally is also a very demanding and often frustrating period. Startup problems can become serious ii they impede the early achievement of full plant production. Raw materials are wasted, manpower is unproductive, field modifications can be extremely expensive and market commitments may not be met. This paper outlines a well proven and highly successful approach to eliminating many of the problems and frustrations often experienced in plant startup. The procedures and methods summarized in the following paragraphs have been developed over a period of 25 years during which some 90 plants were started up.

Jan 1, 1981

By Art Hamid, Manfred Wong, R. John Caulfield

"The proposed Channel Tunnel is a critical component of the San Francisco Public Utilities Commission’s (SFPUC) Central Bayside System Improvements Project (CBSIP), which is a key element of a $6.9-billion sewer system improvement program to upgrade its aging and seismically vulnerable wastewater facilities. The tunnel will provide gravity conveyance and storage of combined sewage flows from the northeast sector of San Francisco, CA to the Southeast Water Pollution Control Plant for treatment. The tunnel will be approximately 2.7 km (1.7 miles) long and 7.3 m (24 ft) in internal diameter. It will utilize a single-pass precast concrete segmental lining system. Tunneling challenges include excavating with pressurized face tunnel boring machine (TBM) technology through highly variable ground conditions including the Franciscan Complex (rock and mélange), clayey/silty sands, stiff to hard clay (Old Bay Clay) and mixed-face conditions. The project will also require several deep shafts that will be technically challenging. Project backgroundThe SFPUC is a department of the City and County of San Francisco, CA that provides municipal power, drinking water and wastewater services to San Francisco.San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. The sewer system includes tunnels, large storage/transport boxes, 1,600 km (1,000 miles) of collection sewers, 28 pump stations and three wastewater treatment plants. After decades of service, much of the system is nearing the end of its useful life.The existing system is also vulnerable to seismic damage. During the 1989 Loma Prieta earthquake, damage to SFPUC wastewater infrastructure was extensive. This included the 3,415 m (11,200-ft) long, 1.7m (66-in.) diameter Channel Force Main, built in 1976, and a critical component of the conveyance system. The Channel Force Main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the Southeast Water Pollution Control Plant for treatment. It is antiquated, not pile-supported and not constructed to current seismic codes. There is also currently no conveyance redundancy for north/central bayside flows to the treatment plant. Figure 1 shows the SFPUC’s wastewater collection system, the existing Channel Force Main and the project location."

Jan 5, 2017

By Tristan Joubert, Fabio Panella, LiLing Chen, Yung Loo, Michael Devriendt, Nasir Qureshi, Ahmad Ali

Tunnel inspections have traditionally been carried out manually by inspectors writing up observations and taking photos of defects. The results from the inspection and the defects observed are dependent upon the rigor of the inspectors and may be subject to repeatability and consistency issues and is often time consuming with elevated health and safety risks. This paper will discuss work that is being carried out in developing and implementing an innovative hardware and software solution integrating machine learning to automate the process of capturing objective tunnel condition information, offering cost and programme savings as well as health and safety improvements

Jun 13, 2023

By Jesus M. Rohena

Concrete pipes and small boxes have been installed by the jacking method. This paper will describe a recent project were large concrete boxes were installed by the jacking method. This project is in the city of Boston, MA. By now everyone in the USA knows something about this project. The project official name is The Central Artery/Tunnel Project (CA/T). This is the biggest public work project in the USA right now, with an estimated construction cost of 14 billions. The main objective of the CA/T project is to replace an existing artery built in the 1950s to increase capacity and safety. One section of the new artery will cross under several railroad tracks near the South Station. To construct the section of the new artery under these tracks, big concrete boxes were installed by the jacking method. The jacking method can be used to install pipes, small concrete boxes, and the CA/T project has demonstrated that big concrete road tunnel boxes can be installed by jacking.

Jan 1, 2003

By Larry Murphy, Mohammad R. Jafari, David M. Giel, Sharat K. Kalluri

"Built in 1940’s to provide a key roadway arterial between New York and Boston, the Heroes Tunnel is the only highway rock tunnel in the state of Connecticut and is part of the Wilbur Cross Parkway. This 365.0 m long tunnel consists of two barrels, each with two lanes of traffic, and carries over 71,000 vehicles per day. For nearly 70 years, the tunnel has seen millions of vehicles pass through but time has taken its toll and now the tunnel lining, ventilation system and radial section joints are significantly deteriorated and in need of rehabilitation. Owned and maintained by the Connecticut Department of Transportation (CTDOT), CTDOT initiated a unique managed approach to mitigate the risk, social impacts and financial implications associated with rehabilitation of this tunnel. This new approach consists of performing field inspection and conducting a comprehensive study to explore six rehabilitation options, including construction of new tunnels and enlarging the existing tunnels. The main criteria for this study are: Impact on traffic and the resulting delay cost; Construction cost; Construction duration; and Construction complexity. This paper will present the results of the alternative study. PROJECT BACKGROUND Location and Importance Heroes Tunnel is located in the State of Connecticut within the Town of Woodbridge and the City of New Haven near the Town of Hamden border. Heroes Tunnel is the only true highway tunnel in the State of Connecticut. The tunnel is part of the Wilbur Cross Parkway (Route 15), a scenic connection between Hartford and New York. Originally constructed and opened to traffic in 1949, the tunneled portion of the parkway passes through the West Rock Ridge. The tunnel was originally named West Rock Tunnel, but was re-designated as Heroes Tunnel in 2003. Route 15 is a vital roadway within the State transportation infrastructure. In the vicinity of Heroes Tunnel, Route 15 carries approximately 71,000 vehicles daily. Locally, Route 15 provides access to residences, shopping centers, and points of interest, as well as other state roadways. Regionally, Route 15 connects New York to the Hartford area and serves as an alternate expressway route to I-95 and I-91. The tunnel is approximately 365.0 m long and passes through the West Rock Ridge. West Rock Ridge is an 11.3 km long rock ridge located on the west side of New Haven. A network of suburban streets abuts the mountain on all sides and a seasonal paved park road climbs to the crest of the ridge. Figure 1 depicts the tunnel topography and location."

Jan 1, 2016