Search Documents

By B. H. Kaye

Particle-size Distribution Specifications for Particulates. Feed to and finished products from size-reduction operations are defined in terms of the particulate sizes involved. It is also well to know whether the ultimate individual particle is being measured, or, if any aggregation or agglomeration of particles exists, whether this has been created by the size-reduction operation. The most complete description of a powder is given by its particle¬size distribution. This can be plotted in terms of cumulative percent oversize or undersize in relation to the diameters of particles, or it can be plotted as a distribution of the amounts present in each unit of diameter against the several diameters. It is common to employ a weight basis for percentage, but there are some data in the literature where frequency, or number of particles, is used. The basis of percent¬age, whether weight, frequency, or some less commonly used factor, should be specified, as also should be stated the diameter, its units, and preferably whether determined by sieve, settling velocity, or other¬wise. Fig. I presents two sets of distributions-ore cumulative and the other in unit intervals. The slopes of the 5-µ intervals of the cumulative curves are converted to percent per micron and plotted as a block, or histogram, from which smooth curves are derived. Powder A has a narrower, or tighter, size range for the bulk of its weight than powder B. Both materials have the same weights below and above the size marked by the arrow. Simpler treatments of distribution are possible. In some cases the significant value is the top size. Since the 100% point is dubious, some amount, as 95 or 98%, so specified, can be called top size. In other cases the percent on some sieve helps define coarseness. Merely stating that all, or all but a small percentage, passes a given sieve is inadequate for defining the true fineness or a material. Complete parti¬cle-size analysis to show the distribution is essential for most compari¬sons and calculations. Particle-Size Equations. A number of equations have been pro¬posed to correlate the quantity of a particulate material with its parti¬cle size to obtain a distribution relationship. 's 19 In the literature it is often assumed that a powder must follow some distribution, such as the Rosin-Rammler-Bennett:20, 21

Jan 1, 1985

By D. J. Hutchinson, S. Nickson

Cable bolts are used as a means of rock support around underground excavations in many mines across Canada and around the world. A substantial body of research on cable bolting was conducted at a number of Canadian universities and mines from the mid-1980s through the 1990s. Since then, research into selected areas of cable bolting practice has continued in Canada. The research has focussed on cable bolt instrumentation and on the inclusion of cable bolts in empirical stope design techniques. A review of cable bolting practice is now warranted at many mines. It has been five years since the completion of the previous substantial body of Canadian academic research and the associated advancement in understanding of cable bolt design, implementation and verification practice. Attempts were made at that time to transfer the new design procedures and performance assessment technologies to mine-site personnel. In some cases, this was effective, and ground control personnel continue to improve on their cable bolting practice at each specific mine site. However, at other sites, experienced people have moved on, and the new, less experienced personnel do not have access to the training or technical resources required to improve their understanding of the subject. In other cases, the technology was not transferred effectively to practitioners, with the result that substantial improvements can be made to the cable bolting practice at those mines. Guidelines for auditing cable bolting practice are provided in this paper. The guidelines include a discussion of the objectives of the audit, suggestions for audit procedure and a summary of the possible outcomes of a cable bolt audit. The objectives of an audit might include assessing the reasons for unexpected cable bolt failures, evaluating the quality of the installation procedures, quantifying the efficiency of the cable bolt system and assessing training requirements and procedures. A cable bolt audit should include consideration of all aspects of the cable bolting cycle, including the design, implementation and verification phases of the operation. At the end of the audit, a ranking should be assigned to the components of the cycle. The ranking system can then be used to identify items that require immediate attention, others that could be improved and others that are adequate. Following completion of a cable bolt audit, increased confidence in the support system and its application is generally, found, along with the potential for cost savings in many cases.

Jan 1, 2002

By William A. Turcotte

Introduction The need for water is fundamental to every minerals processing operation. Though this may sound rather elementary, it is one area that cannot be over- looked. Frank C. Quinn in his paper entitled "Water Is Water Is Water" (1967) said, "but it isn't as simple as that. Very often research is slowed down and production is hampered because of a lack of appreciation for the behavior of water." The quantity of water needed for any operation is determined from bench and pilot plant testing. The quality required by the process for both fresh and reuse water is also established during these two testing phases. Quinn's statements are true whether the process involves the paper industry, the minerals industry, or any other industry. It is not the author's intent to cover water quality, quantity, or re- cycle in specific terms, but to provide the reader with a general outline of the topic with reference to several valuable sources of information. The first part of the chapter will cover several of the areas that have been de- tailed by others and also provide a list of reference sources. The references at the end of the chapter are not all inclusive but will provide a good starting point. In the second part of the chapter, a detailed description, with flowsheet illustrations, is pro- vided on the evolution of the reclaim (reuse) water system at the Tilden concentrator. Mineral Industry Water Needs Beresford and Edler (1978) surmnarized the minerals industry's need for water this way: "minerals are necessary to a modern complex technological society. The minerals industry, while its water needs are relatively minor compared to large users such as agriculture, nevertheless requires a large quantity of water to carry out daily operations from mining to final product refining." In 1973 total water use in the United States was estimated at 15.14 billion cubic meters (4 trillion gallons) for the minerals industry. Of this, about 69% was recirculated within the system. In 1982 Watt and Horton stated that the percent of recycled water in the minerals industry had improved to 73%, showing the minerals industry is an efficient user of water and that steady improvement in water recycling is something the minerals industry can look to with pride. The percent of water needed by the United States' minerals industry was estimated in 1962 to be about 2% of the total water required by industry

Jan 1, 1986

By David P. Keller, George Podolsky

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The world production of iron oxide pigments is estimated by the authors to be between 350 and 400 kt. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test which now has some 20,000 years of exposure. In addition to abundance, iron oxides (about 7% of the earth's crust) have the advantage of low cost, permanency, and are non- toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when these properties were desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States, the combined production of natural and synthetic iron oxides produced sales of over $97 million in 1980 (Spimad, Jr., 1980), increasing to $138 million by 1990 (Templeton, 1990) NOMENCLATURE With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products that are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a competitive commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and are able to command a premium price over iron ores used for steel manufacturing. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary particles are produced as opposed to the use of comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1994

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By Pengfei Wang, Guorui Feng

"With the depletion of easily minable coal seams, less favorable reserves under adverse conditions have to be mined out to meet the market demand. Due to several historical reasons, a large amount of remnant coal was left unrecovered. One such case history occurs with the remnant rectangular stripe coal pillars using partial extraction method at Guandi Coal Mine, Shanxi Province, China. The challenge that the coal mine is facing is that there is an ultra-close coal seam right under it, with an only 0.8 to 1.5 m sandstone dirt band in between the two. The simulation study was carried out to investigate the simultaneous recovery of upper remnant coal pillars while mining the ultra-close lower panel using longwall top coal caving (LTCC). The remnant coal pillar was induced to cave in as top coal in LTCC system. Physical modelling shows that the coal pillars are the abutments of the stress arch structure formed within the overburden strata. The stability of overhanging roof strata highly depends on the stability of the remnant coal pillars. The gob development (roof strata cave-in) is intermittent with the cave-in of these coal pillars and the sandstone dirt band. FLAC3D numerical modelling shows that the multiple seam interaction has a significant influence on mining-induced stress environment for mining of lower panel. The pattern of the stress evolution on the coal pillars with the advance of the lower working face was found. This demonstrates that the stress relief of a remnant coal pillar enhances the caveability of the pillars and sandstone dirt band below them.INTRODUCTIONChina is one of the world’s coal-rich countries. Coal has played a significant role in the growth of China’s economy. Coal reserves have been mined commercially in China for over one hundred years. The demand for coal in China is still going to grow at a relatively high rate (BP Energy Outlook, 2019). Long-term large-scale and intensive coal mining activities have created tension between increased demand and limited resources (Bai et al., 2018). Easily minable coal seams such as sub-horizontal, tabular, and laterally extensive coal seams are being depleted, and therefore the remaining reserves are becoming less favorable. However, in many situations, the coal reserves under adverse conditions have to be mined out to meet the market demand for energy.Due to sedimentary environments and geological conditions, many coal seams are interspersed with sedimentary bands, or partings both within an individual seam and between seams. These bands and partings lead to appearance of ultra-close coal seams, as well as giving rise to considerable variation in their structural and mechanical properties (Ghabraie and Ren, 2016). Difficulties are encountered in the mining of such coal seams. If ultra-close coal seams are mined sequentially, that requires the design of a mining system for each individual coal seam; also, a large number of gateroads have to be excavated, which is not a high-efficiency option. If ultra-close coal seams are mined at a great mining height at once, for instance, using longwall top coal caving—a longwall mining method that is widely used in China for the mining of ultra-thick coal seams—then the location and characteristics of the band would have a significant influence on success of their extraction."

Jan 1, 2019

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden

"Current Environmental Protection Agency (EPA) risk models and asbestos fiber counting techniques for monitoring airborne exposures treat all fibers as being equivalent and ignore the effect of dimension on toxicity. While this may have been appropriate when modern analytical methods were not available, the measurement world is now fully capable of making the appropriate distinctions. The importance of width as a determinant of carcinogenicity has been recognized for nearly 30 years within the published literature. Stanton,1 in a landmark study of a suite of fibrous materials, found that durable mineral fibers with widths less than 0.25 mm and lengths longer than 8 mm were causally associated with the induction of tumors. Pott,2 in a later study, postulated a fiber toxicity model that agreed reasonably well with the Stanton findings, but extended the concept to include varying toxicity as a function of length and width. Wylie et al.3 reanalyzed samples used by Davis et al.4 and found that tumor generation was strongly and inversely correlated with fiber width. Crump5 testified increasing fiber length was correlated with disease occurrence. Lippman6 reviewed a number of studies and suggested that mesothelioma was closely associated with long, thin fibers. Berman et al.7 published a risk model, which found that disease was correlated almost exclusively with fibers longer than 40 mm and width less than 0.25 mm. Recently, Loomis et al.8 reanalyzed textile mill samples and found that aspect ratios greater than 40:1 were highly correlated with disease. Incorporation of width into risk models has been limited by the availability of data from operating asbestos plants and, in particular, the observation of an asbestos plant for which there is no observable mesothelioma. There have been only limited studies published on the dimensions of asbestos fibers, with a few serving as the primary references in other literature.9_13 A rare opportunity to collect detailed concentration and dimensional data of airborne crocidolite from an operating asbestos-cement plant using modern analytical procedures arose, providing a chance to supplement the existing literature on airborne fiber dimensions. The asbestos-cement plant is located in the eastern end of Cochabamba, Bolivia along Highway 4. Cochabamba is a relatively large city located in the Andes Mountains, approximately 250 km southeast of the capital La Paz. The city sits in a valley that runs east-west with mountains to the north and south. The crocidolite used in the products made at this facility is mined in central Bolivia, approximately 75 km northwest of Santa Cruz. The crocidolite is a fibrous magnesioriebeckite 14 (blue asbestos). Crocidolite fibers from Bolivia were the subject of prior reports suggesting the fibers are generally longer and thicker than crocidolite from Australia or South Africa.9 At the cement plant, the run-of-mine crocidolite was first pulverized using a hammer mill and then sieved on vibratory sieves to produce fibers of limited size ranges for use in the cement. The sieved crocidolite is mixed with other components, including recycled cement product, to produce a slurry that is vacuum filtered into sheet form. The sheets are then manually molded into a corrugated shape, air dried, and sawed (using circular saws) to accepted dimensions. The sawed sheets are cured in soaking pits for 28 days before being shipped to the consumer. Prior to shipping, the sheets are finished by a light hand sanding followed (at customer request) by applying one or more coats of paint. A detailed description of the cement plant and the industrial hygiene results can be found in Van Orden et al.15"

Jan 1, 2012

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017

By C. W. Fitzgerald

INTRODUCTION Continuous mining machines are used in regular flat ore beds having uniform thickness. Since coal is the most common type of material occurring in such beds, most continuous miners are used for the extraction of coal from underground mines. The first continuous mining machine for under¬ground coal mining was introduced in 1948. In one machine, the continuous miner combines the functions performed by a conventional face drill, a cutting ma¬chine, and a loading machine. It breaks or digs the material out of the surrounding solid and transfers the material back through the machine chassis by means of a chain conveyor. The conveyor carries the material to a haulage system, usually a rubber-tired vehicle known as a shuttle car. Generally, continuous miners are used in seam heights from 890 to 3660 mm (35 to 144 in.). For seam heights of 1070 mm (42 in.) or less, the haulage system may be a multiple-bridge conveyor or battery-powered tractors that haul low-bed trailers. Proj¬ects are being undertaken by private industry and through government contracts to develop a continuous haulage system for all seam heights. As of 1976, the majority of continuous miners were of two types. The first type is the drum miner, which mounts the cutting elements on a series of drums across the cutting head of the machine, sometimes using a cutting chain to cut clearance for the gear drive. In the drum-type machines, the cutting head rotates parallel to the material face. The second type is the auger miner, which utilizes cutting elements mounted on two auger-type cutting heads. One head is located on each side of the machine, with the heads mounted per¬pendicular to the material face. Chain-head ripper-type miners/miners having rotary cutting elements with oscillating motion and twin-head boring-type miners have all been popular within the last 15 years. Although these are considered obsolete, some machines are still being supplied for specialized applications. GENERAL DESCRIPTION This chapter describes only continuous mining ma¬chines available as manufacturers' production models as of September 1976. Figs. 1 through 11 illustrate some typical machines currently in use. Cutting Elements The cutting elements are the interface between the machine and the material being mined. In describing the cutting elements, consideration must be given to the differences between the drum- and auger-type machines, the bit-tip speeds, and the bit types. Drum-Type Continuous Mining Machines: Three of the four principal manufacturers of drum-type miners use multi-motor designs that provide separate a-c motors for driving the cutting elements. Gear trains are used to reduce the speeds of the motors to the rotational speeds of the cutting elements. One of the three suppliers drives the cutting elements of its low-seam models with a heavy-duty drive chain that is equipped with cutting bits; all other functions of this machine have separate motor drives that are either electrical or hydraulic. The fourth principal manufacturer generally provides two a-c electric motors, utilizing gear reducers, drive shafts, and hydraulically operated engaging clutches to power all of the operating functions, including the cut¬ting elements. Some drum-type miners use trim chains, equipped with cutting bits, to cut clearance for the gear drives. These trim chains vary from two 305-mm (12-in.) chains to one 760-mm (30-in.) chain per machine, de¬pending upon the manufacturer's design concept. In all machines other than the low-seam models that use chains to drive the heads, the trim chains are driven by sprockets on the drive shaft of the final cutterhead drum; therefore, the trim chains are not used for power trans¬mission to the cutting elements. In addition to cutting clearance for the gear drives, the trim chains provide uniform bit spacing all the way across the head and assist in moving the cut material to an area where it is either loaded directly into the miner's conveyor or is easier to load into the conveyor. On a drum-type mining machine, the cutting ele¬ments all rotate from the top to the bottom. Therefore, the recommended procedure is to raise the cutterhead to the maximum seam height, sump the entire machine forward to maximum depth by means of a crawler drive, and then shear downward until the cutter elements reach the floor level. The maximum sump depth varies ac¬cording to the drum diameter, the type of material, the floor conditions, and the operator's abilities. It normally varies an average of 460 to 760 mm (18 to 30 in.). Cutter drums are supplied with two types of cutting bit holders. Weld-on holders are attached permanently. Pin-on holders are replaceable at the face. Cutter-drum diameters over the bit tips vary from 660 to 965 mm (26 to 38 in.), depending upon the chassis height of the machine and the range of cutting heights. Auger-Type Continuous Mining Machines: As cut-

Jan 1, 1982

By M. J. DeJong, R. J. Mair, S. Ritter, G. Giardina

"For urban tunneling projects it is essential to predict and prevent building damage. Although various case studies and experiments have shown that buildings considerably modify greenfield soil movements, widely accepted damage assessment methods neglect this soil-structure interaction and simplify structures as linear elastic beams. This paper summarizes an experimental investigation of the response of more realistic structures to tunneling-induced deformations. Small scale structural models with façade openings and brittle material properties were 3D printed and tested in a geotechnical centrifuge. Soil and structure displacement data were obtained by image-based measurement. Results demonstrate that structures notably mitigate differential greenfield ground displacements. It is also shown that maximum soil settlements, horizontal soil displacements beneath the structure and structural damage in the form of cracking significantly depend on the position of the structure in the settlement profile. The results provide a basis from which to predict building settlement response with greater certainty. INTRODUCTION With continuing population growth and increasing urbanization expected in the next decades, there is an urgent need for a next generation of infrastructure. It is likely that a large part of this infrastructure will be underground. Such creation of urban underground space frequently involves the excavation of shallow tunnels in close proximity to existing structures and utilities. For example, along the Crossrail project in London more than 1,200 structures are located within a possible influence area of the tunnel construction (Torp-Petersen and Black 2001). The assessment of building damage plays a vital role throughout the planning, design and construction stage of urban tunneling projects. However, while predictions of tunneling-induced deformations in the greenfield can generally be made with some confidence, much uncertainty exists about how structures interact with ground movements arising from tunnel construction."

Jan 1, 2016

By Chiranjibi Santi, Amit Kumar Gorai, VIVEK KUMAR HIMANSHU

Air overpressure (AOp) and peak particle velocity (PPV) are the most undesirable effects of blasting in mines. It is an urgent need to design a predictor model for AOp and PPV for universal applications to minimize environmental effects and damages that occur due to blasting. The present study attempts to design an artificial neural network (ANN) model for the prediction of AOp and PPV in different conditions. In this study, the blast design parameters (number of holes, depth of the blast hole, stemming length, spacing, burden, distance of vibration monitoring location from the blast site, charge weight per delay) of two active mines (coal and iron ore) are considered in four different conditions for training and testing of the model for the prediction of AOp and PPV. The model was trained and tested in four different combinations of data (trained using data of one mine and tested using data of another mine, trained and tested using data of coal mine, trained and tested using data of an iron ore mine, trained and tested using combined data of both the mines) for examining the applicability in different conditions. The results indicate that R2 values are ranged from 0.886 to 0.908 and 0.8728 to 0.8959, respectively, in the prediction of PPV and AOp. A comparative study of the performances of the developed model with the other empirical model is also demonstrated. For this, the site constants of different empirical models were estimated individually for both the mines. The study results indicated that the ANN model performs much better than all the empirical models. It can be inferred from the results that blast vibration cannot be accurately predicted only from charge per delay and distance from the blast hole. The ANN model was considered many other factors and thus can predict the vibration level more accurately.

Jul 30, 2021

By J. C. Bradbury

The Illinois State Geological Survey's program in industrial minerals is twofold-the gathering of information on mineral raw materials and the generation of data on the use of these materials. The first function is carried out by the Industrial Minerals Section and the Clay Resources and Clay Mineral Technology Section of the Geological Group, and the second is the responsibility of the Chemical Engineering Section of the Chemical Group. Gathering in formation on raw materials includes both mapping of resources and fundamental geological research. Recent and current research projects include studies relating lithologies of limestones to their physical properties, investigation of sulfur dioxide reactivity of various types of limestone, lithostratigraphic studies of limestones of Mississippian age, investigations of heavy minerals in Cretaceous, Tertiary, and Pleistocene sands, studies of the environments of clay deposition, electron microscope studies of clays and limestones, and investigation of long-term expansion in ceramic products. A relatively recent development that relates more to dissemination of information than to research is environmental geology. This affects the Survey's industrial minerals program chiefly by stimulating the study of rock and mineral resources in metropolitan areas and reporting the results for the land- use planner as well as the engineer or mineral producer. The Survey's program of research on the use of industrial minerals was expanded and diversified in 1966. Incorporating a minerals beneficiation lab, the program is designed to develop new uses for existing mineral resources and to assist producers in implementing these ideas: Projects of the minerals engineering program have included the separation of a feldspar concentrate from certain glacial outwash and river sands, recovery of kaolinite from the waste from silica sand operations, development of the use of an Illinois clay as a binder for pellets, and investigations into the use of fly ash and fluorspar mine tailings.

Jan 1, 1970

By William W. Edgerton, Moussa Wone, David H. Corkum, Carlton M. Ray

"The DC Clean Rivers (DCCR) Project is a 25 year, $2.6 Billion court ordered project to reduce combined sewer overflows (CSOs) discharging into the Potomac and Anacostia Rivers and Rock Creek, and also reduce flooding in the northern areas of the District of Columbia. Like all massive infrastructure programs, DCCR faced technical challenges, management challenges, risks of cost and schedule overruns, procurement challenges, and financing challenges. While DC Water is no stranger to large capital improvement projects (CIP), this CSO Program represents a once in a lifetime event for the Owner requiring the assembly of a single purpose team to implement. Some of the DCCR Project team’s most successful accomplishments to date are attributable to its introduction of early contractor involvement (ECI) to thoroughly vet the work from the perspective of the future constructors, development of functional baselines to share risks that are difficult to price and reduce reliance on geotechnical baseline interpretation during tunnel excavation, and attainment of financing through Municipal Century Green Bonds based on using design criteria of a minimum of 100 year life for the structures to establish intergenerational equity and fairness. This paper will discuss these innovations in detail and provide some sets of recommendations for the underground industry on when and how to use different approaches to better manage projects of this magnitude. INTRODUCTION The District of Columbia Water and Sewer Authority (DC Water) is an independent multi-jurisdictional authority that was established in 1996. Its primary mission is to provide water distribution services to more than 640,000 residents in the District of Columbia (District), and sewer treatment and disposal to 1.6 million residents of the District, Montgomery and Prince George’s counties in Maryland and Fairfax and Loudoun counties in Virginia."

Jan 1, 2016

By Carlo Sampaio, Moacir Veras, Aaron Young, Carlo Petter

"Three major challenges for the mining industry are the minimization of energy use, water consumption and environmental impact. Therefore, any technique that reduces milling waste, decreases water usage and shrinks impact during mine life must be considered a major innovation in mining.To these ends, one of the most impactful developments in mining within the last 10 years has been the expanded use of high technology sensors to create preconcentrations of mine ore (Jönsson, 2014). The most common sensors used are charge-coupled device (CCD) cameras, that allow through a red, green and blue (RGB) coloring system, the separation of minerals with different colors, tones and, in many cases, with differences in brightness.More recently, the development and use of dual energy X-ray transmission (DE-XRT) to enable the separation by atomic density of the constituent minerals within a given rock has become a reality. Within this work, a rapid bibliographical review of the CCD and DE-XRT methods and examples of their usage within mining and the industrial minerals sector are presented.Sensor-based sorting in miningAutomation within mining is one of the industry’s current goals. Sensors of various kinds have been used as steps toward automation in recent years, from improving the safety and productivity of haul trucks through the use of cameras and global positioning satellites (GPS), to the divination of slope failures. Just as with other mining areas, sorting has improved dramatically and made great steps toward automation in recent years (Wotruba et al., 2014).Sensor-based sorting (SBS) uses spectromatic sensors to identify intrinsic characteristics of particles and separates them by either mechanical or pneumatic means into different product streams (Wotruba et al., 2014). SBS can be used with great effectiveness to improve gravimetric beneficiation through the selective separation or preconcentration of run of mine ores (ROM)."

Jan 1, 2015

By John W. Carson, David S. Dick

The last few years have produced new methods of characterizing flow properties of bulk solids. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field condi¬tions. In addition, the effect of large par¬ticles on a material's flow properties (cohe¬sive strength, bulk density, wall friction) can be determined as well as the effects of var¬ious additives such as freeze conditioning agents. New developments have occurred with devices to improve the reliability of solids flow. Much attention has been paid to find¬ing ways, by using inserts, to provide a mass flow pattern with relatively shallow hopper walls. Such devices can also provide reli¬able in-bin gravity blending of bulk solids or completely nonsegregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. The technology and hardware for running bench scale flow tests on bulk solids samples and transforming the results into reliable designs has been in existence for nearly 30 years (Jenike, 1964; Marinelli and Carson, 1986). It has been shown repeatedly that reliable materials handling systems can be designed to avoid the problems of no-flow due to arching or rat-holing, erratic flow, segregation, loss of capacity, or spontaneous combustion. Running flow properties tests and carefully designing a bulk handling system are not expensive, particularly when compared to downtime costs and continual flow problems. New developments in characterizing flow properties of bulk solids include: • a shear tester for measuring the properties of run-of-mine ores containing large par¬ticles; • attrition testers to simulate a wide range of flow conditions; • a tester to measure the wear rate of liners in bins, feeder parts, etc.; • a dustiness tester to measure the potential for dust and the effect of dust control meas¬ures; and • techniques for measuring the strength of frozen ores and the effect of freeze condi¬tioning agents. In the area of improving the flow of bulk solids, there are new techniques for ensuring reliable flow without using up excessive headroom. These include: • belt-to-belt transfer chutes to handle po¬tentially sticky, abrasive, and dusty ores; • designs for the interface between a bin/ hopper and apron or belt feeders to avoid hangups and minimize feeder loads; methods to feed solids reliably into a pres¬surized process; and designs for handling systems that will mini¬ mize attrition, avoid segregation, or auto¬matically blend materials together. Characterizing flow properties Large shear cell It has long been known that the cohesive strength of a bulk solid is due mainly to its fine fraction. However, the effect of the larger particles (that were assumed to re¬duce the strength) could not be measured. The development of larger scale (205 mm¬diam and 0.6 x 0.9 m or 8 in.-diam and 2 x 3 ft) shear testers has made it possible to measure the properties of a wider range of materials. Now cohesive strength measurements can be made with up to 100 mm (4 in.) particles. The results obtained from the large shear testers, together with the results of the nor¬mal shear tests on the fine fraction, are used in the design of reliable stockpile reclaim systems and crusher feed systems. A high percentage of large particles can reduce the measured shear strength of a bulk solid. However, segregation may alter the size distribution and should therefore be considered (Carson, Royal, and Goodwill, 1986). In addition, larger particles will

Jan 1, 1989

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

By E. De Souza, H. Heidrich

In underground operations the evaluation of blasting fume dilution times and the application of recirculation techniques require accurate determination of the concentration of toxic fumes produced by the explosive used. This paper describes a methodology for obtaining concentrations of detonation products from commercial explosives tested under typical rock confinement and looks into the development of techniques for reducing toxic gases produced by explosives. This paper also analyses the application of techniques for the removal of toxic gas which would enable reduced re-entry times, a reduction in the quantity of fresh air and the use of air recirculation techniques, thereby providing substantial economic benefits to the industry. INTRODUCTION Toxic fumes from blasting operations are among the most common and serious hazards encountered underground. The implication of high concentrations of toxic gases emitted from blasting on the mine ventilation system are very significant and, in many cases, catastrophic results have occurred. Because blasting is a routine practice underground, the mining engineer is always confronted with the problem of controlling the fumes within acceptable levels. Typical control procedures employed underground include preventing or reducing the amount of fumes liberated from blasting through the proper selection of explosives and proper blasting techniques; removing the fumes through local exhaust systems or auxiliary ventilation (dilution ventilation); blasting off-shift, or at restricted times; localizing or isolating the effects of blasting where workings are isolated or sectionalized in the ventilation system; and absorbing some of the components of the fumes using air-water sprays. Dilution is one of the most effective control measures against blasting fumes and is universally applied. However, for precise determination of the dilution times for the fumes to reach safe concentrations, accurate determination of the concentration of toxic fumes produced by the explosives used is required. Research work has been carried out in determining the types and volumes of gases produced from blasting. In the case of ideal detonations, the nature and quantity of the fumes produced can be predicted by thermo-hydrodynamic calculations. However, commercial explosives exhibit non-ideal behaviour which is enhanced by the relatively small diameters of application in underground mines. The confinement offered by the surrounding rock further complicates the situation. It is well recognized that confinement affects performance and consequently fume generation. A detailed data base of fumes generated by commercial explosives at various conditions is introduced and the effect of blasting parameters such as, confinement, shock desensitization and incomplete detonations on toxic fume production is described for a variety of commercial explosives in use today. Thermodynamic predictions on fume production by the explosive compositions tested are also presented and compared with experimental results and their significance in assessing the quantity of fumes produced is discussed. A mathematical model capable of determining dilution ventilation requirements and dilution times to reduce the fume concentrations in the blasting zone to acceptable levels has been developed and it is being incorporated into a network system so that the effects of blasting can be simulated in typical mine ventilation systems. Solutions to the problem of controlling blast fumes within acceptable levels are described. These solutions include the use of control procedures which prevent and reduce the amount of fumes liberated from blasting. The use of low fume explosives, proper blasting techniques, dilution ventilation and filtration can be combined to effectively control fume production and save on costs. The application of these techniques to enable recirculation of underground air with reduced quantities of fresh air requirements is evaluated in a case study.

Jan 1, 1993

By J. R. Frederick

Introduction In response to industry needs and requests, Joy Mining Machinery is aggressively evolving a "game changing" system of underground development mining machinery. This entry-development system (EDS) project is concentrated on providing clean, protected and ergonomic operator areas and a quantum leap in productivity. To meet these goals, a virtually continuous and automated mining system is needed. Operators must be able to efficiently and ergonomically perform required functions from a protected environment. Health-related issues, such as respirable dust and noise, must also be addressed. A new concept system of integrated face equipment, from the continuous miner to and including advancing the section belt and services, is needed. Phase I of the project was aimed at developing the bolting technology required. Through acquisition of Cram Australia and joint development efforts with Canyon Fuel Co., Joy now has this capability. The test platform, known as the Joy Multibolter, has successfully completed its trials at Canyon Fuel's SUFCo Mine (Fig. 1). These tests validated the bolting technology and operator protection and ergonomic issues. Phase II includes the development and testing of an integrated mining machine (IMM) capable of advancing a heading 1.5 m (5 ft) while simultaneously cutting a fullface width (single pass) and installing a complete bolt pattern. The IMM, unveiled at MINExpo 2000, incorporates the bolting technology of the Multibolter with automated full-face cutting. This machine was designed to meet Joy's stringent health, operator protection and 300m/d (1,000-ft/d) productivity goals. Phases III through V will include development of processes and integrated haulage, ventilation, power, material handling and section services advancing equipment. Processes and equipment developed will be designed for seamless integration into a complete entry development system. The focus of this paper is the new continuous miner (IMM) development, proposed testing and expectations for the EDS. The IMM is scheduled for commissioning and trials beginning in April 2001 at the SUFCo Mine. SUFCo Mine Canyon Fuel Co. is jointly owned by Arch Western Resources and the Itochu Corp. of Japan. It owns and operates three coal mines in Utah: the SUFCo Mine in Sevier County, the Skyline Mine in Carbon and Emery Counties and the Dougout Canyon Mine in Carbon County. Incorporating state-of-the-art-mining technology and advanced mine management practices, the SUFCo Mine is one of the most efficient underground coal mines in the world. The SUFCo Mine is located approximately 50-km (30 miles) northeast of Salina, UT, in the Wasatch Plateau portion of the Uinta coal basin. The mine property consists of 9,900 hm2 (24,470 acres) with approximately 118 Mt (130 million st) of recoverable reserves. Public utilities and industrial concerns purchase approximately 95% of the coal mined at SUFCo through short- or long-term contracts. Coal reserves are extracted by longwall mining, and the panels are developed using continuous miners. The longwall face at SUFCo Mine is 283-m (930-ft) wide, and the seam height ranges from 2.4 to 4 m (8 to 13 ft). The two development sections are in full operation using Joy 12CM12 continuous miners. Two super longwall panels, under development in the northeast portion of the lease block, are 4,270-m (14,000-ft) long with a 283-m (930-ft) wide longwall face. Each panel contains approximately 5.4 Mt (6 million st) of recoverable coal. SUFCo has been a world leader in productivity for a

Jan 1, 2003

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991