Search Documents

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 µ m fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 µ m. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1993

By C. Hanson

Two modes of potential loss of oxime extractants in liquid extraction processes for the extraction of copper have been studied. In loss "by chemical degradation, two mechanisms of acid hydrolysis are possible, some reagents degrade primarily in the organic bulk phase, Others at the interface between the organic phase-- phase protects the oxime but salts added to the aqueous acid phase can promote the rate of degradation. The reagents reported on are the LIX series (Henkel Cpn), SME529 (Shell Chem.Co.) and P5100 (Acorga) Loss by organic entrainment in the aqueous phase leaving mixer-settlers has also been studied, parameters investigated including impeller/tank geometry and the phase inlet arrangements. The consequences of extractant loss by the above mechanisms...are commented upon. They include the direct economic cost, the possible environmental problems and the implications for downstream operations such, as electrowinning.

Jan 1, 1980

By J. Y. Kim

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In the present study, the flotation response of silver from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (Ag, CU)2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1990

By G. Paul Anderson

Personnel at Utah Copper Division's Bingham Canyon Mine use current computing technology to compile pertinent production statistics and mining plans. Within hours after the day's work has been completed, concise reports summarizing the previous day's production statistics, actual production vs. budget statistics, the location of shovels relevant to the mining plan, the performance of equipment, equipment next scheduled for maintenance, etc. are available at the terminals located throughout the mine. Also, engineering personnel us e computerized systems, directly from their offices, to assist them in the timely development of mining plans. Timely and concise reporting and planning capabilities such as these assist mine personnel in their efforts to review mining progress and equipment performance, and as such they are in a better position to detect adverse trends early and to seek appropriate resources or make changes in plans or practices.

Jan 1, 1977

By Jaime Lomelin

The brines from the sub-surface of the Laguna del Rey dry lake are pumped to Química del Rey, S. A. plant, where they are cooled in adiabatic crystallizers precipitating sodium sulphate decahydrate. This salt is dehydrated in multiple effect evaporators and dried in rotary kilns producing high purity anhydrous sodium sulphate. The spent brines from the sodium sulphate operation are concentrated in solar ponds, precipitating astrakanite and leaving a brine with a higher concentration of magnesium ions. This brine is treated with calcium chloride solution to eliminate the remainder of sulphates, leaving a solution of magnesium chloride ready for the manufacture of refractory grade magnesium oxide or periclase. The magnesium chloride is reacted with dolime to produce magnesium hidroxide which is washed, filtered, and calcined to produce soft burned magnesium oxide, which is briquetted and dead burned to produce the periclase.

Jan 1, 1984

By R. O. Y. Breese

The term "diatomite" implies the nearly pure sedimentary accumulation of diatoms. Sedimentary and chemical purity, low density, inertness, intricate fine structure, high brightness and other properties give the diatom and diatomite unique industrial usefulness and commercial value in high value functional filler and specialty filter aid products. Although diatomite deposits occur commonly throughout the world in Miocene and younger marine and lacustrine sediments, deposits that contain significant reserves of crude suitable for these quality sensitive markets are uncommon. U.S. production is centered on exceptional deposits located in Arizona, Nevada, Oregon, Washington and California. Evaluation of deposits requires understanding of geology, mining, production and end use. As crude quality in deposits varies within and between strata, ore suitable for quality sensitive end uses must be identified through sampling and evaluation programs tailored to permit recognition of critical variations.

Jan 1, 1989

By G. L. Merritt

The implementation of the Surface Mining Control and Reclamation Act of 1977 (SMCRA) has evolved into one of the most complex environmental protection programs to come out of the late 1970's. The level of detail in the statute and the regulations have resulted in a rigid and complex set of requirements for the administration, permit-ting, inspection and enforcement of the program. In addition, the constant change of the federal program caused by regulatory changes, reorganization of the Office of Sur-face Mining Reclamation and Enforcement (OSMRE), ongoing litigation involving OSMRE, and the use of the budget to establish additional mandates on OSMRE and the State Regulatory Authorities have resulted in an unstable program. The instability of the program makes it extremely difficult for the States to implement their programs and to achieve the goals of SMCRA.

Jan 1, 1988

By Chi-shing Wang

In many cases the roof strata of a bedded deposit may be considered as a composite of rock beams of rectangular cross section, whose component layers differ in thickness and may or may not be separable from each other when they are subjected to loading by their own weight. An analytical study of the behavior of such multiple-layer beams is extremely difficult owing to the heterogeneity and anisotropy of rock materials. The complexity is revealed by the fringe photographs obtained from several series of barodynamic photostress experiments conducted on various types of multiple-layer model beams of a medium-grained Bedford limestone. Further discussion on the applicability of barodynamic photostress techniques to the model study of the behavior of mine roofs in stratified geologic media is presented by comparing the phenomenological observations recorded in this investigation.

Jan 1, 1968

By J. K. Brooke

Fluorine is a lively element in both its chemical and economic behavior. It was not isolated as an element until 1886 by Moissan. However, its principal source to this day, fluorspar, was known and its special merits recognized long before that time. Our own mining brother, Agricola, is credited with having named fluorite, the mineral name, in 1546 from the Latin, "fluere", to flow. It made things melt and was already being used as a flux. Because fluorspar has been found as a relatively common gangue mineral in metal ore veins, it has long attracted the attention of geological thinkers seeking to, explain the whys and wherefores of veins. Fluorine has been thought of as one of the principal mineralizers, holding metals in ascending vein solutions for deposition close enough to the eventual surface to be accessible for profitable mining.

Jan 1, 1964

By K. Hanna

This paper describes a method to improve coal mine entry intersection design. The method considers the effect of in situ stresses, local geologic conditions, rock physical properties, and mining sequence. Development of the method is discussed, including the results of field instrumentation studies and numerical modeling investigations. Data required to evaluate the effects of roof span, mining sequence, entry orientation, and bolting patterns on intersection stability are also presented. Ground control studies conducted by the U.S. Bureau of Mines in two underground mines in the Illinois Coal Basin have shown that in situ horizontal stresses and roof geology have a critical effect on intersection stability. Methods to reduce the adverse effects of these parameters are emphasized. Typical failure behavior associated with specific geologic and horizontal stress conditions is' presented to illustrate proposed control methods to alleviate adverse ground conditions.

Jan 1, 1988

By R. M. Parlman

Interest is increasing in obtaining incremental improvements in mineral recoveries in flotation processes because of changing world economic conditions. Research on collector reagents, long indispensable components in flotation systems may provide the cheapest and simplest route to higher metal recoveries. Sulfhydryl group - containing compounds (-SH) and their salts, e.g., dithiophosphates, xanthates and a few other derivatives are commonly used to promote the flotation of sulfide minerals. Alkyl mercaptans, another class of sulfhydryl compounds, have long been known to have collecting properties but have been relegated to dormancy for one reason or another. This paper reports results from new investigations of alkyl mercaptans, trithiocarbonates, and a petroleum oil with a variety of western domestic and Canadian ores for copper and molybdenum sulfides recovery. Specific opportunities are pointed out to the industry for mineral recovery enhancement through the use of the proper reagent combination.

Jan 1, 1980

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By Lester F. Sanford

Located in the Santa Cruz Mountains eight miles north of the City of Santa Cruz and inland from the coast, lies a typical beach sand consisting of quartz and feldspar grains of the Santa Harguerita formation of the middle tertiary age, Reserves of over twenty-five million tons of this sand form the deposit presently being harvested by Pacific Cement & Aggregates, a Division of Lone Star Cement Corporation. The deposit ranges from 350 to 700 feet above sea level and varies from two percent passing a 200 mesh screen to ten percent retained on a ¼ inch screen (see Figure '#l) In 1929 the first sand plant went into operation at this site. It was replaced by a new plant in 1937. This plant continued operation until the middle of 1965 when replaced by the modern plant described in this paper.

Jan 1, 1967

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By Joseph G. Selmeczi

Lime and limestone-based SO2 scrubbing processes have demonstrated reasonably good success in removing low concentrations of SO2 from flue gases. While most of the operating problems experienced in the early days of scrubbing have been worked out, problems usually increase and removal efficiency drops with increased amounts of SO2 present in the gas stream. In order to overcome these difficulties, yet still taking advantage of lime and limestone as the lowest cost neutralizing agents, a host of so-called double- alkali systems were developed. These processes take advantage of cations such as Na+ and NH4+ capable of forming highly water soluble bases or basic salts, such as hydroxide, carbonate or sulfite, which having been neutralized or acidified by the absorbed SO2 can be regenerated with a lower cost base such as lime.

Jan 1, 1974

By Jan M. Mutmansky, Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs.-quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1998

By Kenneth N. Han, Jianshe Liu

Various techniques used in the removal of metal ions from effluent streams have been reviewed. These techniques include recovery of metals by biological treatment, chelating agents, adsorption, ion- exchange and chemical precipitation. The main thrust of this paper however, is concerned with the removal of cadmium and zinc ions from the solution by adsorption utilizing liquid fluidized beds. The bed particles used were silica of 150x200 mesh. The range of the concentration of these ions studied was 10-3 to 10-5 M. Important variables examined included flow rate, concentration of metal ions and amount of bed particles. A mathematical model describing the concentration profile of metal ions in the axial direction in liquid fluidized beds has been developed. The equation of continuity was solved numerically and the results were used to predict the recovery of metal ions in fluidized beds.

Jan 1, 1992

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

Jan 1, 2004

By E. V. Bowman

This paper is intended to deal with the material handling aspects of fine coal cleaning as applied to a recently built plaint in: southern West Virginia. This plant is processing 160 tons per hour of 1/4" x.0 coal on a two shift basis. Past experience with this very friable low volatile metallurgical coal indicated that its plastometer readings, varied directly with the size and length of time elapsing between mining' and ultimate consumption. Due to the mines location with, respect to its consumers, little could be done to decrease the time element. Studies indicated that the plastometer readings are considerably less in the minus 60 mesh range than that experienced in the plus 60 mesh sizes. Therefore, handling the coal in such a manner as to have the least amount of degradation became extremely important.

Jan 1, 1961

By B. J. S. Sceresini

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentra­tion and high pressure to achieve extremely rapid gold dissolu­tion rates. This is made possible without suffering from high energy or wear rates by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device which can be constructed from a variety of wear and chemical resistant materials. High temperature tolerance is also possible so that the device can be incorporated into a pressure leach circuit with significant capital cost savings because of the high capacity to volume ratio that is an inherent feature of the device. For cyanidation applications the outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of about 150 dry tonnes per hour at 40-45 % solids. Service life at this throughput is at least three months. Six mines are currently employing the Filblast Process and another six are conducting plant trials. The ore types range from highly reactive, almost impossible to treat, pyrrhotite/ arsenopy­rite to deeply weathered clay ore which forms a highly viscous pulp. It has been found that the effect of shear thinning has resulted in improved leaching and adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately eight million tonnes per annum. This paper presents the operating benefits and cost savings which have been achieved in four plants, two treating oxide/ sulphide ore blends and two treating highly reactive sulphide ore and concentrate. Filblast leasing and maintenance charges and pump operating costs are about ten percent of the benefits. A conceptual cyanidation circuit based on the Filblast Cyanidation Process is also discussed. The Filblast System is an in-line pressure leach aerator/ reactor which generates very high shear and greatly enhances mass transfer rate by generating extremely small gas particles where oxygen gas is required for oxidation reactions and/or utilising the high shear characteristics to minimise the diffusion boundary layer. Both of these rate limiting factors effect the rate mechanism for gold cyanidation. Initially two multi-stage Filblast aerator cartridges formed a leach train but now the trend is to install a single submersible cartridge of equivalent perfor­mance. This design simplifies installation and minimises change-out times. However the in-line concept can be employed where high pressure leaching or pressure oxidation is required. The reactor is submerged in the leach tank so that the mass of gas micro-bubbles contained in the discharging slurry is entrained in the agitator vortex and is thoroughly dispersed throughout the tank. A diagrammatic representation of a leaching circuit incorpo­rating the Filblast Reactor is shown in Figure 1. The recirculation pump takes new feed directly from the cyclone overflow trash screen either under gravity or pump fed and recirculates the balance to maintain 250 - 270 m3/h total slurry flow. All of the leach feed slurry gets at least one pass through the Filblast thereby eliminating short-circuiting. Typically a 6/4 EAH Warman pump drawing 60-70 kW is required to circulate 250 m3/h through the system. The back pressure generated by the Filblast is in the range of 400-500 kPa depending upon pumping rate, pulp density and slurry rheology. The high shearing rate effectively negates the viscous effect of slurries and the addition of a gas further reduces the pulp density by virtue of the intensely aerated, homogeneous medium. The gold leaching Filblast cartridge elements are made of polyurethane but stainless steel, ni-hard, rubber or ceramics can be used depending on the operating temperature and design duty. The efficiency of the Filblast Leach Reactor in gold cyani­dation is due to the extremely efficient mixing, oxygen dissolu­tion and surface polishing action of the Filblast design. Either air or oxygen may be used but Atomaer recommend the use of oxygen because of the rate benefits gained from cyaniding at [02] significantly > 20 ppm D O in the reactor. Very high DO concentrations have been measured; in excess of 50 ppm. There is some debate as to whether the value is a true measure of the DO or the oxygen meter sensor is measuring the effect of a mass of very fine bubbles of free oxygen. Regardless of the fact the reactor has registered some amazing gold dissolution rates commonly in excess of 80 % during transit of the pulp through the reactor. The elapsed time is less than half a second!

Jan 1, 1995