Search Documents

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By Richard O. Y. Breese

Geologically and commercially, the term diatomite is applied to the nearly pure sedimentarv accumulation of diatom frustules- the microscopic skeletons of unicellular aquatic algae belonging to the class of golden brown algae, bacillariophyceae. The sediments are fine-grained, siliceous, and consist primarily of amorphous opaline silica with only minor amounts of organic residue, secondary minerals, and co-deposited non-diatomaceous or crystalline clastic debris. In the geological sense, the name diatomite implies sedimentary accumulations that have reached appreciable thickness and when thick enough, such accumulations consequently may have possible commercial potential. Although the term diatomite is popularly and inappropriately applied to any sediment in which there is an abundance of diatom frustules, alternative terminology is more correctly employed to describe the less pure diatomaceous sediments, for example: clay-bearing diatomite or diatom-bearing clay. Synonyms in current usage include diatomaceous earth and kieselghur. More antiquated and obsolete terminology includes tripoli-powder, tripolite, and infusorial earth. Worldwide, diatomites occur within Tertiary to Recent lacus- trine and marine sedimentary facies. Although diatomite is wide- spread throughout the world, deposits that contain high purity, commercially versatile ore are uncommon. Physical properties of the diatom and of processed diatomite that provide unique commercial value in a broad spectrum of market end-uses include ornate fine structure, low bulk density, and high porosity and surface area. Properties of equal importance are mild abrasiveness, high absorptive capacity, insulating ability, relative inertness, and high brightness. End-use markets are diverse and range from insulating brick and absorbents through quality sensitive filter aids and premium quality functional fillers. Notwithstanding both the economic attractiveness of the specialty markets and the commercial versatility of the high purity deposits, deposits of lesser purity are mined in nearly all parts of the world for less demanding uses. Mining costs are minimized through open pit quarrying, but in Europe, Asia, Africa, and South America underground mining methods are also employed. Blasting is not required because diatomite is soft and easily broken loose with mechanized equipment. Following gentle crushing, the ore is dried, milled, and processed into one of three broad categories of products: naturally milled, straight calcined, and flux calcined grades. Each of these principal categories is further subdivided into additional grades through particle size adjustment of the powders. Agglomeration of particles, alteration of fine structure, and color change are achieved through calcination. Flux calcination further accentuates these changes. Production throughout the world is dominated by the United States, followed by Romania, the former Soviet republics, and France. Other major producers include Spain, Mexico, Iceland, Korea, Japan, and Germany. Denmark is a major producer of Moler earth products, which consist of a diatomite-clay mixture. HISTORICAL BACKGROUND The first industrial use of diatomite can be traced back some 2000 years to the Greeks and to the use of diatomaceous earth as a component in lightweight building brick and in ceramic pottery. It was not until the mid-1800s, however, that the unique properties of diatomite were first recognized and the market end-uses explored and developed. One of the most important of the early uses followed the development of dynamite by Alfred Nobel in the mid-1860s, whereupon diatomite was used as a component of the explosive to improve stability and safety. Other early uses included low temperature insulating and refractory bricks and as a component in insulating and fireproofing construction panels. During the 1920s, processing technology underwent a very rapid evolution with the development of calcination, flux calcination, and air classification technologies. Through these technologies, innumerable different size and grade classifications could be made for market applications and for rapidly diversified end- uses. Today, the application of processed diatomite for filter aid is the largest of the quality sensitive end-uses. Specific filtration uses include the clarification of beer, wine and liquor, vegetable oil, syrup and sugar, pharmaceuticals, and swimming pool water, to name a few. As a functional filler and extender, processed diatomite is ideally suited for application in paint, rubber, and plastic formulations. Other filler applications include use as an anti-blocking agent in plastic film, anti-caking agent for fertilizer, thermal insulating material, catalyst carrier, polish, abrasive, pesticide and fertilizer carrier, and chromatographic supports. Throughout much of the world diatomite is still used as a component of insulating brick and as an absorbent.

Jan 1, 1994

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth's surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth's surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET's uranium exploration procedures.

Jan 1, 1981

By C. Widham

Introduction It is generally accepted as dogma that sampling contributes most of the error in gold fire assays. Differences in assay results on pulps from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" of relatively coarse gold particles. It is true that coarse gold particles can contribute to substantial sampling fluctuations. But, while the process of sampling is probably the major source of error, the analytical process cannot be completely ignored as a possible contributor to erratic assay results. To maintain a stable assay process, the analytic part of the system must also be kept in control. One method of monitoring the performance of the analytic system is to systematically assay standard materials, whose sampling characteristics are carefully controlled. Gold assay standards are not prepared, nor can they be prepared, to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for both preparation (i.e., comminution and splitting) and fire assaying and then come to conclusions only about the fire-assay process. Because most gold ores are very heterogeneous, sampling errors would, in most cases, completely mask the contribution of the analytical errors. Assay-standard material is prepared only to assess the accuracy and variability in the fire assay process. Because the objective of the assay standard is to provide information about the fire assaying, it is necessary to control the sampling error of the standard material, so that it is only a minor constituent of the discrepancies observed in any assay results. To do this requires that the particle size of the standard material be reduced to a point where the relative standard deviation of the sampling error (i.e... the standard deviation of the errors divided by the average gold content of the material) is 2% or less. For all but very homogeneous mineralization, this means that the material must be reduced to 100% -150 mesh before the sampling errors are adequately controlled. However, even reducing the particle size can contribute to sampling problems. The liberation of gold may cause segregation that can cause large sampling fluctuations that are not easily controlled while maintaining the desired grade. Because, in most cases, the standard material would already be in the "pulp" state when it is submitted to a lab for assay, it is not possible to entirely conceal the nature of the sample from the lab. This is a problem inherent in using assay standard material. Because of the contribution of sampling to error generation in the assay process, the use of "coarse" material does not solve the problem of submitting a totally "blind" standard to the lab. In the sections that follow, the selection, preparation, testing and use of gold fire assay standard material is discussed. While some may dismiss the production of standard material as folly, it is possible to produce and utilize standard material to stabilize and improve the fire-assay process to produce more reliable assay results. Material selection It is desirable to use material that has as nearly the same metallurgical characteristics as the samples with which the standards will be included. However, this is usually difficult. For many reasons, including the particle size at which a significant amount of the gold mineral is liberated, the sampling characteristics of even -150-mesh material may preclude the use of geologically and metallurgically similar ore as a standard. It is usually easier to get material having desirable grade characteristics with the necessary sampling properties than it is to find geologically and metallurgically similar material with the required sampling characteristics. High-grade standards are especially difficult to find and prepare. This is because, as grade increases, the size of the gold particles usually increases. Larger gold particles are liberated and tend to segregate during comminution, and the homogeneity of the material cannot be maintained. For grades much above 3 g/t (0.088 oz/ton), it is very difficult to find material that has the proper sampling properties. Old mill tailings are likely candidates for assay standards. Some of these have sufficiently homogeneous mineral contents, so that the sampling errors can be effectively controlled. Where mill tailings are either not available or are not acceptable, mineralization that has exhibited homogeneous results in reassays of the pulp material is also a good candidate for the standard. Finally, the mineralized rock being sampled may (and should) be used if adequate homogeneity in the -150mesh material exists. "Adequate" ("acceptable") homogeneity is defined below.) It is important to use standards having a wide range of grades. This alone may preclude the material being

Jan 1, 1997

By Yi Yang, Xiuzhu Su, Wei Sung Ng, Shuiping Zhong, Miao Chen

With over 260 tons of gold reserves, the Shuiyindong gold mine is one of the largest Carlin-type gold deposits in China. A particular challenge in the processing of the ore is the presence of carbonaceous compounds, which can cause substantial losses in recoveries via the preg-robbing and adsorption of gold. To investigate the structural properties of the native carbon and to compare between different characterization techniques for such compounds, pre- and post-flotation mineral samples containing 0.9–4.8% non-carbonate carbon from the Shuiyindong mine have been examined via mineralogical and thermogravimetric approaches, as well as spectroscopic techniques, including X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine edge structure spectroscopy (NEXAFS), solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, Raman spectroscopy and preg-robbing measurements. NEXAFS and DRIFT yielded the most reliable results, indicating that 60–75% of the organic carbon in all samples consist of aliphatic alkenes with substantial unsaturated content, highly similar to activated carbon, with the remainder being graphitic and humic. Speciation by XPS was sub-optimal due to spectral overlaps between graphitic and aliphatic carbon, and between carboxylic and carbonate functionalities, while NMR spectroscopy could not provide reliable speciation of the carbon groups. The preg-robbing strength was strongly correlated to the aliphatic content and structural disorder in the carbon, while no such relationship was found with the graphitic and humic content.

Nov 29, 2021

By Yuchen Wu, Jing Mei, GUOZHONG LIU, KE GAO, Songjie Tian, Jianwei Cheng, Yu Wang, Yuhang Wu, Hui Wang

The stability and integrity of protective coal pillars between the longwall working face and development roadways are greatly affected by the mining activities such as the development face advancing or retreat mining. Due to underground strata pressure, the coal pillar cracks could be further developed and then the air leakage passages (mainly cracks) could be produced greatly. The air circulation caused by the atmospheric pressure difference between the two sides of the coal pillar may also provide suitable conditions for the possible spontaneous combustion of the residual coal in the mine gob. In this paper, a typical the protective coal pillar in a Chinese coal mine is studied. The deformation and stress of coal pillars during the mining process of longwall working face are simulated by using FLAC3D. The displacement and strain of coal pillars are analyzed. Two indexes, the linear fracture rate (LFR) and area fracture rate (AFR), are introduced to characterize the development of internal cracks’ development within coal pillars. By using field measurement, the air leakage intensity distribution due to coal pillar cracks is obtained; the equation of air leakage resistance of coal pillar under the influence of mining is derived. Then, the possible location of large air leakage of coal pillar is determined, which can be used as guidelines to study the possibilities of coal spontaneous combustions happening in pillar or mine gob. The research results help to control such potential hazards in advance.

Jun 16, 2022

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971

By D. Jacobson

There are many different machine design parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the speed at which the cone gyrates. In June 2012, pilot tests were conducted to determine the production and operating conditions over a wide spectrum of speeds. mining operations will have variations in the ore characteristics and feed rates that result in non optimal use of the crushing energy and inconsistent process control. This study documents the measured variation in production and energy efficiency with two operating modes. Overall, the results match the theory, and the capacity and power fluctuated by 25% and 17%, respectively, when operated at full capacity, with an overall trend of slightly coarser discharge size distribution as the speed decreased. Using a fixed feed rate, the crushers had 4-14% higher production when operating at the optimal speed. Secondary analysis showed that the power draw consistency and magnitude of power spikes could also be improved by optimizing the cone speed. Varying the speed of the crusher can be used to tune the crusher during commissioning, adapt to changing ore conditions over long periods of time or be used as a dynamic input into an advanced control system. each action above would serve to make the crusher(s) more productive, more energy efficient, impove process control and would also have mechanical benefits for the machine

Dec 1, 2013

By O. Babak, O. Leuangthong, M. A. Cuba

Integration of data from multiple sources and/or multiple scales is a common, yet challenging aspect of geostatistical resource modeling. Common approaches to data integration are based on a cokriging framework that assumes a consistency of scale in the information that leads to a requirement to composite the data prior to model construction. It is well known that the geostatistical model parameters are scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the semivariogram that should be used in model construction and/or the assessment of volume-variance relations as it affects resource estimation. This paper reviews and compares two different approaches for semivariogram upscaling. The first approach is the scaling laws. It is an empirically derived approach, involving several simplifying assumptions, one of which is a strict assumption of invariance of the semivariogram shape. The second approach is a theoretically derived direct upscaling of the semivariogram. This approach has been around for a number of years, but is seldom implemented due to software limitations. In this paper, we present a numerical integration approach to facilitate direct semivariogram upscaling. The advantage of direct upscaling over the scaling laws approach is shown by considering a synthetic example and a case study. Further, in the case of multiple codependent random variables, the extension of the direct semivariogram upscaling to the cross semivariograms is derived and an upscaled consistent linear model of coregionalization is presented.

Jan 1, 2013

By I. H. Warren

Hydrometallurgy has a well-known and established role in the production of manganese metal (1) and manganese compounds, including battery grade manganese dioxide (2). Also, several leaching processes have been developed and applied at various times for the recovery of manganese from low grade ores (3). Recently, interest in the hydrometallurgy of manganese has been stimulated by the problems presented in the processing of sea nodules (4). Fumes and dusts from the ferro-manganese furnaces also offer a potential field for the application of manganese leaching techniques (5). In treating low grade manganese ores a major requirement of the leaching process is that it should dissolve manganese from a mixture of manganese and iron oxides. The most selective reagent for this purpose is ammonium carbamate applied after preliminary pyrometallurgical reduction of the ore (6). Since soluble carbamate complexes of the postulated type (7) are formed by both manganous and ferrous, but by neither manganic nor ferric, ions, selectivety of manganese leaching is achieved by control of the reduction operation to yield, essentially MnO and Fe304? A potential improvement to this two step process would be to simultaneously reduce and selectively leach the manganese in one hydrometallurgical operation. This possibility has been experimentally studied and the results are described below. During the preliminary study of the stability of solutions of ammonium, ferrous and manganous carbamates at elevated temperatures, it was observed, contrary to the observation of Welsh (8) at lower temperatures, that

Jan 1, 1971

By J. H. Hill

The globalization of mineral markets and intense competition in downstream mineral-consuming industries such as transportation, agriculture, and construction are requiring raw materials suppliers to innovate, improve quality, invest in new technology, and control costs. Mineral specifications are becoming more refined, and pressure to improve products is felt from increasing numbers of competing producers, substitute materials, customers, and regulators. As a result, engineered mineral products are becoming more like manufactured ones in terms of cost structure, differentiation, and the importance of market driven, customer specific product development. Engineered mineral products are defined as those where the costs of refining and upgrading outweigh those of conventional mining activities (blasting, crushing, classification, haulage etc.), and where close control of physical and chemical parameters is required for customers' processing and manufacturing applications. This includes industrial minerals such as calcium carbonate, kaolin, mica, specialty oxides, talc, and some metal powders. It excludes most metals and bulk commodity materials such as gypsum, lime, sulfur, and soda ash. Engineered mineral products are utilized in common household goods, and are at the forefront of industrial materials engineering in plastics, ceramics, composites, glazes, coatings, and construction materials. As a group, they introduce interesting questions to the minerals firm. Advanced materials or basic? Diversify or specialize? What are the implications of advanced materials and for mineral markets, and most importantly, where can the producer look for long-term value, volume, and profits?

Jan 1, 1993

By D. Malhotra

Most primary-molybdenite producers use a selective-flotation process in which molybdenite is floated from the ore while other sulfide and non-sulfide gangue minerals are depressed in the same step (Figure 1). The process was developed at the Climax mill. Reagents used in the rougher-flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother) and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born, et al, (1976) and Malhotra, et al, (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50 percent of the total molybdenite-flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors which would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate non-oil based collectors and collector systems that are less expensive than vapor oil.

Jan 1, 1985

By J. E. Russell

The purpose of this paper is to describe an independent study which forecasts Texas coal production, specifically for electric power generation. This study, extending to the year 2000, is justified on the following basis. Texas produces and consumes considerably more electric energy than any other state, has consistently high growth rates in the population and industrial sectors, and has large lignite reserves. Also, since recent forecasts have been criticized as overly optimistic, this study is timely when considering the long lead times required in obtaining new power sources. In the study demand for electric energy was assumed to rest on two dominant factors: 1) overall state of the Texas economy as measured by the Texas Gross State Product (TGSP) and 2) Texas population. Demand models were prepared and tested following a study of several options. A final linear regression demand model with time lags for the two variables was chosen on the basis of good correlations. On the supply side, uncertainties such as impact of nuclear sources, gas-fired cogeneration, and ratio of imported to lignite coal exist. These uncertainties were studied with high and low cases for effects on lignite. Finally a simple supply model was chosen. Results of the study indicate that lignite production in Texas will rise from the current (1984) 40 million tons per year (XTPY) to the range of 77 to 124 MTPY and more probably 100 HTPY in the year 2000.

Jan 1, 1984

By Keith S. Olsen

Any discussion of barite mining is virtually impossible without considering, almost in the same breath, the many other variables, such as beneficiation, transportation, infrastructure and location that impact the economics of a particular barite orebody. My comments will be limited to just the mining aspects of barite orebodies and these observations must be considered in proper context with all other parameters affecting exploitation of a barite property prior to final decision on economic feasibility. In many instances low-cost mining situations are more than offset by high-cost beneficiation requirements. Likewise, there are cases of relatively high-cost mining associated with no or low-cost beneficiation requirements thus permitting economic exploitation. Barite orebodies and occurrences are almost as varied as the number of occurrences. As in most mining situations, the design of a mine plan and implementation of a proper exploitation program must be approached on a case by case basis. Proper and sufficient geologic control of a barite orebody must precede the development of a mine plan. Generally speaking, barite orebodies can and, at many times, do "strange" things; pinch with depth; almost never increase in size with depth, overturn, fault-off, change grade, etc. Due to the extreme variable nature of most barite orebodies, a mine plan and its implementation must be as flexible as possible. The ability to quickly adapt to variable conditions will greatly enhance the economics within a particular barite mining environment.

Jan 1, 1980

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 1960's, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

By C. M. Sliepcevich

This paper is a brief status summary of investigations by the authors over the past decade to develop a continuous process for recovering' high purity metal powder from pregnant solutions by gaseous reduction at elevated temperatures and pressures. Although these studies included extraction of other metals such as nickel, silver, and gold, this presentation will be confined to the hydrogen reduction of acidic and ammoniacal solutions of copper. The continuous hydrogen reduction process (CHR) described herein enjoys the environmental advantages of other hydrometallurgical processes but, in addition, provides a substantial benefit in fuel economy over competing processes. As was recognized by Schaufelberger in 1956, for a given amount of fuel a continuous hydrogen reduction process has the potential for producing four to six times as much metal as an electrolysis process (1). Although hydrogen reduction of metal salt solutions has been known for more than a century, extensive development work leading to commercialization was not initiated until the 1950's. Since then, commercial applications relative to other extractive techniques have been minor and have been confined to batch or to continuous, completely-mixed autoclaves. By contrast, the process described herein utilizes a continuous, tubular reactor which is operated in modified plug flow so that only limited and localized backmixing occurs. Thus, gradients in concentration, temperature, and pressure exist over the length of the reactor, the presence of which can be utilized to advantage for achieving high conversions and product quality (2, 3).

Jan 1, 1975

By D. J. Boron, R. Kollrack

Introduction The US has the largest total (364 Gt, or 401 billion st) and recoverable (182 Gt, or 201 billion st) coal reserves in the world (Steam/Its Generation and Use, 1978). However, progressive coal use in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. Since the promulgation of the Environmental Protection Agency (EPA) New Source Performance Standards (NSPS), it has become apparent that all US coals will require sulfur removal to comply with the new sulfur dioxide emission levels. If more stringent emission standards are imposed, through pending acid rain legislation or amendments to the Clean Air Act, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the development of new and advanced coal cleaning technologies to continue and promote the use of coal. Table 1 summarizes the EPA NSPS for sulfur dioxide emissions. Fortunately, the basis for determining sulfur dioxide removal is the Btu and total sulfur content of the run-of-mine coal. Thus, credit is given for any sulfur removed before combustion, e.g., through physical coal cleaning. Unfortunately, physical coal cleaning alone may be unable to produce a compliance coal with respect to the EPA NSPS. Therefore, all industrial and utility coal-fired boilers will require post combustion gas cleanup, e.g., flue gas desulfurization (FGD), to comply with the new regulations. Table 1 - EPA NSPS for SO2 Emission Category SO2 Content of ROM Coal SO2 Reduction Required 1 0-2 Ib/M Btu 70 2 2-6 Ib/M Btu To 0.6 Ib/M Btu (70% to 90%) 3 6-12 Ib/M Btu 90% 4 12 Ib/M Btu To 1.2 Ib/M Btu Alternatives to post combustion gas cleanup, such as staged combustion, lime and coal injection, fluidized-bed combustion, and chemical coal cleaning, are currently under development. Of these, chemical coal cleaning offers the advantages of providing (1) high quality fuel for combustion (low sulfur and ash, high Btu, and attenuated product variability); (2) a solid fuel product for use in retrofitted gas and oil boilers; and (3) a solid fuel product with multiple end uses, e.g., internal combustion engines, carbon electrodes, coke, or chemical feedstock. Gravimelt process In the Gravimelt process, 1.4 mm x 0 (14 mesh x 0), physically beneficiated coal of about 5% moisture is fed into a 3401 to 3901 C (644 ° to 734 ° F) molten bath of sodium hydroxide and potassium hydroxide. Organic and pyritic sulfur and most of the mineral matter in coal react with and are dissolved in a molten mixture of potassium hydroxide and sodium hydroxide. The reacted coal sulfur is converted to alkali sulfides and polysulfides, whereas the mineral matter is apparently converted to alkali-aluminum silicates and other byproducts that are water and acid soluble. Coal residence time is 60 to 240 minutes. The sodium hydroxide to potassium hydroxide ratio is about 9:1. The total hydroxide-to-coal ratio is no less than 10:1. The specific gravity of the caustic melt is about 1.8 g/cm3 . Thus, coal is buoyant in the bath, and insoluble mineral matter with density greater than 1.8 g/cm3 would sink. Reacted coal is first water-washed with an equal weight volume of water in a countercurrent mode of operation. The coal is filtered and the filtrate sent for regeneration. The coal is then acid-washed in 10% sulfuric acid. The acid-water/coal mixture is filtered to recover the final coal product, and the filtrate treated with lime to precipitate dissolved mineral matter. The precipitate is filtered from the mixture and discarded. The water is recycled to the plant. Filtrate from water-washing is treated to remove sodium sulfide. The sodium sulfide is chemically treated to produce hydrogen sulfide, calcium car¬bonate, sodium hydroxide, and other products. The hydrogen sulfide is treated to produce sulfuric acid for the acid-washing step. The calcium carbonate is treated further or discarded, and the sodium hydroxide is concentrated by evaporation and recycled to the reactor. The Gravimelt process is currently at the bench-scale stage of development. A 0.9-kg (2-lb) continuous reactor is in operation with a continuous water- and acid-washing section adjacent. The regeneration section is not developed to a meaningful extent, although key reactions have been tested in the laboratory. Process conditions, product recovery efficiencies, etc., however, have not been determined adequately and continuous regeneration operation has not been attempted. Work is now in progress to develop each section to a continuous bench-scale operation in processing coal at 9.1 kg/h (20 lb per hr). Microwave process The carbon and hydrogen in coal are relatively transparent to microwave radiation. However, water, caustic, pyrite, and other mineral matter components are strong conductors of microwave radiation energy at the proper frequency. As a result, selective heating of the noncarbonaceous materials occurs that enables the chemical reaction of sulfur and ash with caustic. Although very high temperatures may result from

Jan 1, 1987

By Harold Bloom

The Mount Pleasant Mines, or Mount Pleasant Joint Venture as it is presently known, is located approximately 59.5 km (37 miles) south of Fredericton, NB, Canada. Earliest indications of mineralization were found in 1954, during a regional reconnaissance geochemical stream sediment survey carried out over large parts of New Brunswick and the Gaspé Peninsula. The regional geology of New Brunswick is shown in Fig. 1. This program, sponsored by Selco Exploration Co. Ltd. of Toronto was conducted by H. Bloom, H.E. Hawkes, J.E. Riddell, and J.S. Webb. At its conclusion in 1955, 30 significant anomalous drainages were identified for follow-up evaluation. A total of 4937 sample sites were occupied. Geochemical reconnaissance using stream sediment sampling was a new technique which had only been field tested the previous year in the Gaspé and the northern coastal area of New Brunswick. Sediments collected from known mineralized drainages were found to leave a train of anomalous heavy metals from 1.6 to 9.7 km (1 to 6 miles) in length. When the exercise was extended to a reconnaissance survey, the previously unknown mineralized prospect at Nash Creek, New Brunswick, was discovered, staked, and later drilled (Hawkes and Bloom, 1956). Although it did not come into production, the discovery left little doubt as to the viability of the method and led to the Selco sponsorship of the program for the following two years.

Jan 1, 1991

By E. J. Beckman, R. M. Enick, C. Shi

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. Two inexpensive and environmentally benign fluids were selected for the study, water and carbon dioxide. The separation, which is conducted at 295 K and at the vapor pressure of carbon dioxide (6.0 MPa), is based on differences in wettability between the precious metals and other minerals. Contact-angle results indicated that, in the presence of water and liquid CO2, gold is slightly hydrophobic. The addition of CO2-soluble fluoroalkyl thiols or f uoroetherthiols increased the hydrophobicity of gold exposed to water and CO2 to a greater extent than alkylthiols. Minerals, including quartz, pyrite and magnetite, were hydrophilic. During the separation, an aqueous slurry of fine mineral and gold particles was mixed with liquid carbon dioxide. Pure gold particles (-325 mesh) were found to agglomerate at the H2O-CO2 interface. The minerals tended to remain in the aqueous phase. Despite these promising preliminary results, very poor gold recoveries were obtained when applying the procedure to an Australian gravity concentrate. This was attributed to the native gold particles in the concentrate being either too large, agglomerated in slimes or coated with minerals. Although this particular application was unsuccessful, this water-CO2 biphase technique may be applicable for other separations that require the removal of very fine, hydrophobic particles from an aqueous slurry.

Jan 1, 2000

By C. Zografidis

Environmental protection, economic prosperity and respect of the need for social equity promotion, constitute a prerequisite for any modern industry aiming to operate in a sustainable manner. The Natural Stone industry in Europe, a sector comprising mainly of SMEs, despite the fact that consists a dynamic extraction sector, often lucks the resources to apply novel techniques and management schemes towards achieving sustainable performance. I-STONE, an EU Integrated Project funded by the 6th Framework Programme, is aiming to contribute in the improved performance of the Natural Stone industry. A primary project objective is the re-engineering of the stone production chain, in order among others to considerably in-crease its efficiency and productivity, and minimise the amount of stone wastes disposed. The present paper, resulting from the research con-ducted on environmental management within I-STONE, is focusing on the use of sustainable indicators as a tool for the assessment of the stone industry?s performance. Based on Commission Decisions and reported studies, a list of indicators was selected and used within I-STONE, including environmental and socio-economic indicators. A set of selected environmental indicators were quantified based on operational data of a number of Greek and Portuguese quarries examined as case studies. The analysis indicated that an integrated strategy, including the application of novel operation techniques and equipment, waste minimization and systematic environmental monitoring and reporting, constitute key factors for the sustainable operation of natural stone industry.

Jan 1, 2007